Search Documents

By Ray Heater, Qian Liu, Alan Bauer

The channel effect is a phenomenon that takes place with decoupling explosive charges; an air shock wave propagating ahead of the detonation wave in the annular space around the explosive charge compresses the charge so that the process of detonation is modified and even stopped. For commercial explosives, such as AN/FO slurries and emulsions, the channel effect causes partial detonation under certain conditions. To simulate and evaluate the phenomenon, a hydrodynamic model was developed based on the assumption that the pre-shock wave is produced by Mach reflection at the tube walls. Based on instrumented experimental studies with the above explosives in diameters ranging from 25 to 90 mm in pipe sizes ranging from 35 to 127 mm, it has been possible to demonstrate that a criterion for failure based on a critical impulse concept fits the experimental data well. Critical impulse values for the various explosives tested are presented along with the necessary correlations between charge and borehole diameter required to produce this.

Jan 1, 1988

By Brian Stump, Rong-Mao Zhou

A series of single-fired (simultaneously detonated) explosions were conducted in an Arizona copper mine. The explosions spanned yields from 1700 to 13600 lbs (773 to 6169 kg) and were all detonated in an approximate 100 m by 100 m area. In order to quantify the effect of the mine free-face, the individual explosions were also detonated under three different emplacement conditions including at the free-face of the mine under normal burden, twice normal burden and fully contained. The purposes of these experiments were to investigate: (1) Generation of in-mine and regional phases such as Pg, Pn, and Lg from mining explosions; (2) Quantification of the relationship between yield and seismic amplitudes; (3) Quantification of the effect of confinement; and (4) Similarities and differences between single-fired waveforms and those from delay-fired explosions. Instrumentation was deployed at near-source (100-700 m) and in mine (1-5km) distances. Empirical scaling relations for the different shots in this test series were developed in order to quantify the effects of yield and confinement.

Jan 1, 2006

By Mark S. Stagg, Rolfe E. Otterness, Stephen A. Rholl

The Bureau of Mines fired seven test blasts in a 22-ft bench of limestone, screening the material to investigate the influence of explosive type and between row delays on fragmentation. Four 4-hole, single-row test shots were conducted evaluating dynamite, ANFO, emulsion, and a 60-40 emulsion-ANFO mix. Three 12-hole shots, with three rows of 4-holes, evaluated delays between rows of 24, 36, and 120 ms. Accurate in-hole electronic delays were used, firing within 1.5-ms of the nominal delay. All seven shots had a 6- to 7-ft burden, 10-ft spacing, with a hole diameter of 3-1/2 in fired on a 12-ms delay between holes in the row. The tests were instrumented with strain gauges grouted in the burden region examining stress wave and gas pressure effects. Fiber optic probes were used to confirm timing and to obtain detonation velocities.

Jan 1, 1989

By Gungor Tuncer, Ali Kahriman

This paper presents the results of ground vibration measurements carried out in Hisarcik Boron open pit mine located on the west side of the central Anatolia near Kütahya province in Turkey. Within the scope of this study in order to predict peak particle velocity level for this site, ground vibration components were measured for 304 shots during bench blasting. In blasting operations; ANFO (blasting agent), gelatin dynamite (priming) and delay electric detonators (firing) were used as explosives. Parameters of scaled distance (charge quantity per delay and the distance between the source and the station) were recorded carefully and the ground vibration components were measured for all blast events using 2 different types vibration monitors (1 White Mini-Seis and 1 Instantel Minimate Plus Models). The absolute distances between shot points and monitor stations were determined using GPS. The equation of square root scaled distance extensively used in the literature was taken into consideration for the prediction of peak particle velocity.

Jan 1, 2006

By J. Sigler

A series of small scale tests have been performed to establish the effect of powder factor and initiation timing on the grindability of rocks. The blasts were performed in high quality granite blocks, which were cut from stone prepared by dimensional stone quarry operations. Three different types of granite were tested. The charge configurations included detonating cord placed in five holes with water as a coupling medium or concentrated charges of equal mass, placed in the same number of holes, fully stemmed or air decked. The powder factor was varied from 0.4 to 1.2 kg/m3. Typically all charges were detonated simultaneously; however, in some experiments, detonation waves collided in the middle of each borehole and in others a small delay was used between charges. All fragments were collected and screened, and drop weight impact tests were performed on selected size fractions, using different impact energy, to calculate the resistance of the rock to impact breakage. The work index of some of the blasted samples was measured using a standard Bond mill arrangement. The experiments generally showed increased softening of the rock with powder factor, which appeared to be the dominant factor. Charge configuration as well as in-hole collisions of detonation waves affected the initial fragmentation but had little effect on the impact breakage of the samples.

Jan 1, 2008

By John Wright

As part of the redevelopment of the Royal Brisbane Hospital complex in Australia, a number of antiquated buildings were to be demolished and replaced by newer, modem facilities. Aside from the decommissioning of the hospital buildings, the project called for the removal of approximateIy 24,000 bank cubic metres (bcm) of varying quality rock material. Given the sensitivity of the project, in particular the close proximity of the required excavation to the existing hospital structures (-3 metres at the closest point), and the requirement that these were to remain lily operational during the construction phase, it was initially proposed to use hydraulic rock hammers as the primary means of excavation. Poor production rates and unexpected dif3icuIt rock conditions led to a revision of the excavation methods and a feasibility study on drill and blast practices was undertaken. Subsequent to an initial series of trial blasts to illustrate that vibration and flyrock could be adequately controlled, drill and blast methods were used in conjunction with mechanical methods of rock breakage. This paper reviews the drU and blast processes and the practices which were necessary to comply with the multiple constraints imposed on the project. The project has highlighted that modified drill and blast practices remain a cost-effective method of excavation, even in sensitive areas which are commonly deemed inappropriate for such methods.

Jan 1, 2000

By Courtney Vallejo, Rafiqul Tarefder

This study examines the effects of small scale airblast experiments on cohesive soils and the resulting ground vibrations and crater geometries. Relationships for ground vibration attenuation with soil depth and distance from the blast source were developed. The study is part of a broader research topic of understanding the vulnerability of earthen embankment dams to blast loading. Many earthen embankment dams in the United States were constructed more than fifty years ago and were not designed to withstand high-stress loading such as blast loading. These structures may be susceptible to failure and it is important to describe the response of the earthen dam during a blast event.

Jan 1, 2013

By Claude Cunningham

AEL has been developing electronic detonators continuously since 1986. It launched its first system for opencast mining in 1993, and now has two distinct product lines. The path has not been without great difficulty, but the determination to persevere was always buoyed by the strong encouragement of customers who experienced the transformed blasting results, as well as a clear vision of the enormous intrinsic value of the concept. The path of growth to dominant global supplier is traced through the separate application channels of coal stripping, quarrying, massive mining, opencast mining and narrow reef mining, to the first allelectronic detonator demolition blast in June 2001. Reasons for the slow coming to market of this highly desirable concept, which often coincide with reasons for the demise of various other systems, include the difficulty of safely mating electronics and explosives in a low cost environment; the extreme difficulties of achieving proper connection under mining conditions; the rapid rate of evolution of the technology, and the safety concerns raised by various accidents and incidents along the way. ED.s are now established as the way forward and are set to displace other systems in all serious applications. There is place for both programmable and pre-set delay systems.

Jan 1, 2002

By W. Birch

The traditional concept of scaled-distance modelling for predicting blast induced ground vibration holds many drawbacks, not least of which is the major effect data scatter imparts on confidence determination. An investigation by the Department of Mining and Mineral Engineering, The University of Leeds, England has resulted in the development of simple but effective method of improving prediction capacity through the reduction of effective error by incorporating individual location response into a scaled-distance model. The work is the product of an l&month blast-monitoring campaign at a limestone quarry situated in North Yorkshire, England. The data, when presented in the form of a scaled-distance model, indicates a typical scenario where a good overall correlation becomes marred by the extent of data scatter. Examination of the individual monitoring locations however indicates that the response of the individual location is an important factor in the explanation of the large residuals. The novel approach thathas been developed incorporates a series of locational site factors which when incorporated into a scaled distance model reduces the effective error and therefore improves prediction capacity. The approach is based on using a standard computer package “spread sheet” on the understanding that these are commonly available on all quarry or home computers. This approach has been validated by comparison with a more rigorous statistics method.

Jan 1, 2001

By Karl E. Burger

Recently an experiment was completed at the Golden Sunlight Mine, a property owned by Placer Dome Inc. of Vancouver, British Columbia, to measure the Body Waves entering their highwall created by blasting. The purpose of the study was to assess the damaging effects of blasting on the highwall, in order to further slope stability. Stress and Strain experienced in the earth that is created as a result of blasting can be determined by knowing several important pieces of information. These include the compressional and shear wave particle velocities initiated by blasting, the Body Wave travel velocities in both the shear and longitudinal direction, and the densities of the rock in question. A series of equations based on wave theory can then be used to determine the stress and strain affecting the highwalls. The Blasting Engineer can then use this information to design blasts that create peak particle velocities less than levels that maintain the integrity of the highwalls. This paper first discusses the experiment used to measure the Body Wave velocities. It then traces through the subsequent calculations necessary to generate the information needed by the Blasting Engineers, the Mining Engineers, the Geological Engineers, and the Geophysicists to design blasts and develop open pit plans to alleviate unstable highwall conditions.

Jan 1, 1989

By V Krishna Mohan, J Edmund Hay

This paper discusses the results of the gap sensitivity measurements made on water-gel explosives, sensitized by monomethylamine nitrate (MMAN) and flake aluminium, and one emulsion explosive. This study specifically deals with the effect of the mode of initiation, end or center, on the measured L50 values with air gap and coal dust gap for the above explosives. Similar measurements have also been carried out on a nitroglycerine (NG) - based explosive. The results show that the mode of initiation plays an important role in determining the air-gap sensitivity of these explosives. However, in tests carried out with the coal dust gap, the L50 ( grams of coal dust ) values for these explosives are close in both the types of initiation. The results indicate that the sensitivities of these explosives may be ordered in the following manner: NG-explosive>> Aluminized explosive ~ MMAN-explosive > Emulsion explosive

Jan 1, 1982

Bloomfield Collieries Rix’s Creek Mine is an open cut coal operation located in the Hunter Valley region of Australia. The mine produces approximately 1.1 mt of saleable product per year and routinely employs cast-blasting practices for its unique dragline-truck overburden excavation method.

Jan 1, 2006

By Sharon K. Reamer, Klaus G. Hinzen

A series of controlled seismic experiments was performed in a limestone quarry in southern Germany to study seismic effects of cylindrical charges fired in both a half space (HS) (burden 63 m) and quarter space (QS) (burdens of 3 and 3.5 m) geometry. Charge columns contained from 20-32 kg of explosives and initiated from the bottom. The explosives formed a cylinder 4 m (20 kg) and 5 m (32 kg) high and 90 mm in diameter at depths from 3-8 m below ground level. Prior to each of the larger explosions, small charges of 0.12 kg seismogelit were fired at 4 m and 8 m depths in the same boreholes. Seismograms were obtained from 23 three component surface stations and up to 10 three component borehole stations (6 m depth). For each experiment, stations were located on three linear profiles of length 72 m at different azimuths from the source and one semicircular profile at a constant range of 30 m.

Jan 1, 1991

Computational techniques in determining particle size distributions after blasting is getting wide acceptance. A well known approach to extract this kind of information from digital images is edge detection. The number of edge points on a given image increase proportional to the increase of the particles on the image. By selecting a conveniently smooth threshold, counting the signed edge pixels may be a suitable metric further used to quantify the number of particles in the image. Here we propose an image processing algorithm together with Adaptive Neuro Fuzzy Inference System (ANFIS) to efficiently count the rock particles with various sizes on a given surface. To determine a suitable approximation for a mapping between the number of edge pixels and the number of particles, ANFIS is a suitable tool. As a trainable classifier ANFIS proved itself as being better efficient approach than other well known multilayer perceptron classifiers. ANFIS is trained by using convenient training data pairs previously experienced from empirically counted sample images. When given a new image containing the particle information of selected surface, the hybrid neuro fuzzy image processing approach provides satisfying performance on counting the correct number of particles up to the given scale of sizes. In this paper an experimantal study for assessment of particle size using ANFIS is presented.

Jan 1, 2004

By Tom Hale

Developers and blasters are faced with increasing public demand and regulatory restrictions to maintain the lowest possible levels of noise and vibration from blasting operations in populated urban areas. Pyrotechnic products have proven to be a low noise, low vibration alternative to conventional blasting for close-in rock excavation and concrete demolition applications. Pyrotechnic breaking charges often yield 1/10th the vibration and noise compared to traditional explosives, and have been demonstrated to increase public confidence and decreased damage potential where they have replaced explosives, thus allowing new opportunities for work and greater job profitability. This paper presents a practical approach to utilizing pyrotechnic products in various applications including trenching, mass excavation, demolition, and dimension stone production, providing methodology for pattern design, vibration probability and loading calculations. Field research data is reviewed and compared to conventional explosives.

Jan 1, 2008

By B. A. Cheeseman, R. Skaggs, C. F. Yen, S. Wolf

Shallow buried explosives pose a significant threat to lightweight vehicles and their onboard personnel. To date, designers of lightweight vehicles are limited in their knowledge of what occurs during the blast. The high intensity, short term loading imparted by the explosion is enormously complex and can be significantly affected by a number of parameters including the size, shape, type, detonation point and depth of burial (DOB) of the explosive and the type, density and water content of the soil. Recent advancements in numerical simulations have enabled the complex blast event to be accurately modeled by coupling Eulerian and Lagrangian analyses: the former is well suited to modeling the blast and while the latter, the structural response. Further validation of the modeling technique is considered in the current paper, which details simulations performed utilizing the coupled Eulerian-Lagrangian analysis to the study the blast output of explosives buried in saturated sand. These experiments varied explosive charge size, its depth of burial, the target stand-off (SO) distance and target plate dimension. The investigation concludes with a discussion of the accuracy of the numerical simulations when compared with the experimental observations.

Jan 1, 2005

By L. Russell Payne

The use of shock tube in the blasting industry is relatively well characterized and understood within the realms to which it is used. Non-conventional uses of shock tube within the EOD and the Aerospace Industry however has not been as widely researched and published. Characteristics of shock tube such as its reliability, simplicity and its non-electric nature make it ideal for functioning or driving mechanical mechanisms, detonators, and timing devices. Outlined in the text are the performance characteristics of shock tube in an array of atmospheric environments including pressures ranging from ambient to 100,000 ft equivalent atmosphere. In addition the useful exit work energy or impulse of the shock tube for driving these various EOD and Aerospace mechanisms is published as a function of tube lengths and atmospheric pressures. Of particular interest to these devices is the required length of shock tube needed to produce the steady state detonation energies and the accompanying properties of the shock tube at these lengths. Various sources publish an arbitrary run distance for steady state detonation and output some where between 20 cm and 1.0 meter. Statistical and experimental evidence with in the text show these numbers to be low and provides an updated reference for shock tubes usage in nonconventional situations.

Jan 1, 2008

By J P. Tidman

The demand for more data on the detonation properties of commercial explosives grows as blasting becomes a more exact science. Proper use of this information by blasting engineers depends on the appreciation of the assumptions and limitations inherent in calculating energies and pressures of explosives. The strength of an explosive is usually a calculated energy value derived from a model of the explosive. The model may be simple or complex, depending on the thermo-hydrodynamic assumptions made. The calculated energy and pressures of commercial explosives are sensitive to assumptions about their reaction products. The equation of state describing the reaction product gases, the treatment of solid reaction products (e.g. reacted calcium and sodium nitrate and aluminum) and the reaction time are examined to show the variability of calculated results as a result of different assumptions. These same models of explosives also serve to explain phenomena of explosives such as the effect of charge diameter on V.O.D. (and strength) and decoupled explosives.

Jan 1, 1981

By Pharis E. Williams

The ability of voids, microballoons, and even solids to sensitize explosives has been known and used for many years. This phenomenon has generally been studied and reported under the terminology of "hot spots" because of the increase in local pressure and temperature when a shock wave encounters such sensitizers. A method for treating this phenomenon in detonation theory or in a detonation model has been studied for almost the same length of time. Perhaps because of the complexity and non-linearity of the void, or microballoon collapse, several of these studies have used the expediency of including additional terms in the burn rate law to account for the influence of hot spots. The detonation model proposed here considers the sensitization due to discontinuities in the shock impedance to be a mechanical phenomenon to be accounted for in the mechanical equations governing the detonation and not in the burn rate law. While this is not a new contention, the method for handling this non-linear phenomenon within the proposed model is new. The model also includes a method which accounts for the manufacturing variables of emulsion matrix cell size, microballoon size and type, as well as energetic additives.

Jan 1, 1992

By A. S. Tawadrous

The stress field around a detonating charge in a borehole was calculated using AUTODYN for a variety of in-situ stress conditions. Calculations were conducted for zero in-situ stress, hydrostatic conditions at 100MPa, uniaxial stress conditions of 100MPa, and bi-axial state of stress with amplitudes of 200MPa and 100MPa along the axes. Two different explosives, ANFO and emulsion, were used for the calculations. It was shown that in-situ stress fields had an effect on the tensile and compressional damage zones around the blasthole, calculated on the basis of the maximum amplitude of the stress pulses in the rock after the detonation of the explosive in the blasthole. The extent of compressional damage increased around the borehole, whereas, the extent of the tensile damage decreased. The damage zones are of elliptical nature with their axes parallel to the direction of the principal stresses. The difference between the major and minor axis of the elliptical damage was not very significant in the case of the compressional damage; however it was significant in the case of the tensile damage.

Jan 1, 2007