Search Documents

By M. F. Bucek

This report summarizes the activities performed and the results achieved during a two-phased investigation of the technical and economic feasibility of disposing of coal mine refuse underground in active mines, Three coal regions in the United States that are most severely affected by coal refuse disposal problems are identified: southwestern Pennsylvania, southern West Virginia, southwestern West Virginia and eastern Kentucky. For each region, a conceptual mine model is presented that describes the geologic conditions, mining methods, and environmental circumstances typical of that region. The model mine that was prepared for the Kanawha Region in Southwestern West Virginia and eastern Kentucky was selected as the basis for developing alternative conceptual designs of underground disposal systems in the second phase of this investigation. Procedures used in selecting the regions and in modeling typical mines are described in Part I of the report. Part II of the report describes existing methods for stowing refuse underground, presents three alternative conceptual designs of stowing system that would be appropriate for the model mine postulated in the first phase of the study, discusses technical characteristics and environmental effects relative to the various systems, and evaluates the technical and economic feasibility of the three alternative disposal system designs. Comparisons costs among systems and with costs or surface disposal are presented.

Jan 1, 1980

By Matthew N. Rubin

This report summarizes the work performed under USBM Contract No. H0155155. The purpose of this work was to obtain operational data on retrofit noise control treatments suitable for use in coal preparation plants. This data was obtained by evaluating the performance of four categories of noise control treatments which were installed in a commercial coal preparation plant. The four categories of treatments were resilient screen decks, resilient impact pads, chute liners, and curtains. The selection, installation and initial evaluation of the treatments was documented in the Volume I report issued in 1977. This Volume II report summarizes the results of the long-term evaluation of the original treatments, as well as some additional tests which were conducted on elastomer-clad (resilient) screen decks. This project demonstrated the feasibility of a number of retrofit noise control treatments, some of which also proved to be quite durable over the long term.

Jan 1, 1982

By K. L. Paciorek

The aim of this program was to develop a reliable and meaning-ful basts for assessing certain safety aspects, namely fire and, in particular, toxicity hazards of articles employed in underground coal mining operations. This investigation was centered on the thermal oxidative degradation of "pure" ingredients used specifically in the formulation of conveyor beltings. To achieve this goal all products formed on thermal oxidative degradation of the materials studied were analyzed, identified I and the amount of each individual species present was determined quantitatively on a weight of product per weight of material basis. The weight/weight data thus obtained can then be factorized to reflect the relative toxicity of each individual species present, using for example the Threshold Limit Values adopted by the American Conference of Governmental and Industrial Hygienists, whereby an overall "toxicity index" can be arrived at which makes it possible to compare the different potential formulation components in a quantitative manner insofar as their "toxicity" is concerned. Furthermore, knowing the off-gassing characteristics of the commonly used additives I their contribution to the product mix obtained from actual belting can be postulated. Conversely, from the species obtained on thermal oxidative degradation of conveyor belts the type and to a degree the content of additives can be deduced. Based on the se data meaningful regulations governing the material selection for underground use can be developed. For these studies a quiescent system at 370°C was employed. Thermogravimetric and differential thermal analyses were performed to supplement and extend the sealed system investigations and to provide information regarding thermal oxidative behavior under dynamic conditions.

Jan 1, 1975

By W. W. Adams

This bulletin covers all mines in the United States that were operated in 1936 to produce metallic ores and all mines that were operated to produce nonmetallic minerals other than coal, stone, sand, gravel, or their products. Reports from mine operators revealed a better safety record for fatal accidents in 1936 than in any other year except 1934 during the 26 years for which annual surveys of accidents in the mineral industries of the United States have been conducted by the Bureau of Mines. On the other hand, the record for nonfatal injuries, although better in 1936 than in any year prior to 1930, was not as good as it was from 1930 to 1935, inclusive.

Jan 1, 1939

By Philip Thompson

The Bureau of Mines investigated a selective flocculation-flotation technique to remove insoluble slimes from low-grade potash ore in a continous 45-kilogram-per-hour (100-pound-per-hour) process investigation unit (PIU). This research is part of the Bureau's program to improve resource recovery from low-grade ores. Results showed that 84 percent of the insoluble slimes were removed from an ore containing 5.5 percent water-insolubles and 14 percent K20 using a Bureau-developed, cationic flocculant-glycol ester-diesel oil reagent. Subsequent potash flotation recovered 75 percent of the potash in a cleaner concentrate assaying 56 percent K20. Concentrate leaching upgraded the product to market specifications of 60 percent K2O. An economic evaluation by the Bureau suggested that the rate of return on investment, after taxes, should be about 20 percent for such an enterprise.

Jan 1, 1980

By Kenneth M. Maas

The U.S. Bureau of Mines began a five-year study of the 7.0 million acre Ketchikan Mining District during 1990. This study is part of the Bureau's ongoing statewide mining district evaluation program. The study area was subdivided and then prioritized by mineral potential into work units. Bureau field work in 1990 focused on the southern portion of Prince of Wales Island and vicinity. Extensive mineral resources have been mined historically in the area and are presently being evaluated by private industry. Information in this report is based on an extensive literature search and Bureau field work. Over 150 mines, prospects, and mineral occurrences were visited in 1990; an aggregate of 1,300 rock, placer, and limestone samples were taken; and nearly 3 miles of underground workings were mapped. Many prospects, some untouched for more than 80 years, were mapped and sampled. High metal values at several prospects were confirmed by Bureau sampling. Reconnaissance sampling along logging roads on Southern Prince of Wales Island revealed mineralized areas not previously recorded. Follow-up work at many locations is planned for the 1991 season.

Jan 1, 2011

By Shail J. Butani

In 1986 the Bureau of Mines conducted a probability sample survey, Mining Industry Population Survey, to measure such employee characteristics as occupation; principal equipment operated; work location at the mine; present job, present company, and total mining experience; job-related training during the last 2 years; age; sex; race; and education. The population estimates are necessary to properly analyze the Mine Safety and Health Administration (MSWA) injury (includes illness and fatality data) statistics; that is, to compare and contrast injury rates for various subpopulations in order to identify those groups that are exhibiting higher than average injury rates. This report uses the survey's results to characterize the U.S. metallic mining workforce from March through September 1986. Similar reports have been published for the stone, sand and gravel, and nonmetallic mining industries, as well as for the entire metal and nonmetal mining (includes metallic, stone, sand and gravel, and nonmetallic industries) sector and the coal mining sector.

Jan 1, 1988

By W. W. Adams

"The eighth National Safety Competition, that for 1932, conducted by the United States Bureau of Mines, was participated in by 322 mines and quarries operating in 34 States. Tables 2 to 6 show the relative standing of the various plants. Bronze trophies, known as the 'Sentinels of Safety,' which were provided by The Explosives Engineer magazine to be awarded annually by the Bureau of Mines, were awarded to five companies, each company having established the best accident-prevention record within one of the five classes into which all companies were divided, - namely, anthracite-mining companies, bituminous-coal-mining companies, metal-mining companies, operators of nonmetallic-mineral mines other than coal mines, and quarries or open-cut mines. The trophies are awarded for one year and are then transferred to the winners of the succeeding year's contest.The trophy for bituminous-coal mines, which has been in New Mexico for the past year, was won by a mine in West Virginia. The metal-mine trophy goes to New York State for the first time in the history of the contest. Previously it had been won by mines in Minnesota, Michigan, Kansas, and Oklahoma. The trophy for nonmetal mines remains for another year at Retsof, N. Y.; that for quarries and open-cut mines is transferred to a quarry in Michigan. The trophy for anthracite mines, of course, remains in Pennsylvania, as all anthracite mines in the contest are in that State.In determining the relative standing of the various companies enrolled in the competition, all mines and quarries were graded according to their accident-severity rates, - that is, according to the number of days of disability of employees on account of accidents in proportion to the number of man-hours of work done by all employees at the plant. Reports of accidents and of man-hours worked were furnished by the companies to the Bureau of Mines. These reports were carefully examined and classified to insure uniform weighting of accidents according to the number of days of disability to be charged and to insure uniformity of methods of calculating the accident-severity rates for the various mines and quarries. When the relative standing of all plants had been determined in this way, a summary of the records of the companies having the lowest accident-severity rates in their respective groups was sent to the members of a committee of award for examination in accordance with the rules governing the safety contest. The members of the committee of award were W. H. Cameron, managing director of the National Safety Council; William Green, president of the American Federation of Labor; James F. Callbreath, secretary of the American Mining Congress; T. T. Read, Vinton professor of mining engineering of Columbia University; C. B. Huntress, executive secretary of the National Coal Association; A. J. R. Curtis, assistant to the general manager of the Portland Cement Association; and A. T. Goldbeck, director of the bureau of engineering of the National Crushed Stone Association. When two or more mines within the same group operated without an accident during the year, the contest rules provided that the trophy for the group should be awarded to the plant whose record showed the largest number of man-hours worked."

Jul 1, 1933

By J. B. Janus

This report continues a series of analyses of coal samples made by the Bureau of Mines in connection with the yearly purchase of several million tons of coal for various Government agencies. Listed are the analytical data on the composition and quality of tipple and de livered samples of coal collected during fiscal year 1974.

Jan 1, 1975

By Laird Crocker

A goal of the Federal Bureau of Mines is to minimize the undersirable environmental conflicts and impacts associated with mineral processing operations. To help reach this goal the Bureau operated a citrate-process pilot plant for the removal of sulfur dioxide from lead smelter sintering machine waste gases to test the process. The process uses a carboxylate solution such as citric acid to absorb sulfur dioxide from waste gases. The absorbed sulfur dioxide is subsequently reacted with hydrogen sulfide to precipitate sulfur and regenerate the solution for recycle. Nominal capacity of the pilot plant was 1,000 scfm of 0.5 vol-pct sulfur dioxide gas. The pilot plant was operated for over 5,400 hr and produced about 55 net tons of sulfur. The operation demonstrated that (1) 99 pct of the sulfur dioxide could be removed from lead smelter sintering machining waste gases containing from 0.1 to 0.6 vol-pct sulfur dioxide, (2) sulfur precipitation and solution regeneration with hydrogen sulfide in conventional stirred vessels was readily controlled, (3) precipitated sulfur could be continuously recovered as a 99.S-pct-pure product by flotation and melting, and (4) 78 dry-vol-pct hydrogen sulfide gas could be produced from pilot-plant product sulfur, natural gas, and steam.

Jan 1, 1979

By Terry G. Montgomery, Eric S. Weiss, John E. Going, Kenneth L. Cashdollar

The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted joint research on dust explosions by studying post-explosion dust samples. The samples were collected after full-scale explosions at the PRL Lake Lynn Experimental Mine (LLEM), and after laboratory explosions in the PRL 20-L chamber and the Fike I m3 chamber. The dusts studied included both high- and low-volatile bituminous coals. Low temperature ashing for 24 h at 515 °C was used to measure the incombustible content of the dust before and after the explosions. The data showed that the post-explosion incombustible content was always as high as, or higher than the initial incombustible content. The MSHA alcohol coking test was used to determine the amount of coked dust in the post-explosion samples. The results showed that almost all coal dust that was suspended within the explosion flame produced significant amounts of coke. Measurements of floor dust concentrations after LLEM explosions were compared with the initial dust loadings to determine the transport distance of dust during an explosion. All these data will be useful in future forensic investigations of accidental dust explosions in coal mines, or elsewhere.

By Michael J. Jorgensen, Pranathi B. Aedla, N. K. Kittusamy

Risk factors associated with the development of muscu­loskeletal discomfort and disorders during the operation of heavy mobile equipment include whole-body vibration and awkward and sustained joint postures of the shoulders, neck, and trunk. Cab design may influence awkward postures of the joints, and task duration may influence duration of exposure to awkward and static postures and whole-body vibration. To reduce exposure to risk factors related to the interface between cab design and task, it may be necessary for manufacturers to address cab design. This study assessed the repeatability of a cab design checklist developed to evaluate various design characteristics that can influence exposure to risk factors for musculoskeletal discomfort. The ability of the cab design checklist to identify posture-related deficiencies of design was also assessed. The checklist was used by two administrators across 10 pieces of heavy construction equipment. Video analysis was performed to quantify postures of the neck, shoulder, and trunk; correlation analysis was used to determine whether specific questions from the checklist were associated with the identification of awkward postures. The repeatability assessment resulted in kappa coefficients ranging from 0.52 to 1.0 (good-to-excellent reproducibility) across each piece of equipment, and an overall kappa coefficient of 0.77 (excellent reproducibility) when considering all equipment together. Results from the correlation analysis showed that shoulder flexion posture was correlated with scores from the cab design checklist. However, results of the cab design checklist were not significantly correlated with shoulder abduction or awkward postures of the neck and trunk. Results suggest that the cab design checklist may be useful for identifying cab design characteristics that need further improvement and for identifying design characteristics that increase shoulder flexion. The strength of the repeatability assessment suggests that outcomes of the cab design checklist administered by different individuals may be consistent, independent of the type of equipment being assessed.

By E. Concha

The concept of an Automated Continuous Explosive Excavation system (ACEE) for the underground mining applications of development drifting and room and pillar mining has been evaluated in comparison with conventional drill, blast and muck operations. The role and possible extent of application as this method was identified. The evaluation examined each element of existing and of proposed ACEE design concepts in a defined mine environment. Step by step procedures were developed to quantify the evaluation process where this appeared feasible. One conclusion drawn was that a system approach to ACEE design is not only feasible but attainable within the state of the art. Several preliminary design concepts were formulated and examined in order to determine what further research or development might be needed to realize them.

Jan 1, 1982

By Todd M. Ruff

An average of 13 mine workers are killed each year by being run over or pinned by mobile mining equipment. At surface mines, these accidents commonly involve large dump trucks that drive over a smaller vehicle or a person that is in the dump truck’s blind spot. One method of detecting a person or another vehicle in a blind spot is to use some type of sensor technology such as radar or radio-frequency identification (RFID). Researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health tested a number of commercially available and experimental sensors that monitor obstacles in a vehicle’s blind spots. None of the sensors had been previously applied to the specific problem of rigid-frame surface mining trucks. This report documents the procedures and results of tests conducted after RFID and radar systems were mounted on a 50-ton-capacity dump truck. It was determined that both RFID and radar technology show promise for detecting obstacles in the blind spots of mining equipment; however, more development work is needed to meet the unique requirements of mining equipment and the mine environment.

Jan 1, 2000

By R. A. Westin

[Polychlorinated biphenyls (PCR's) have been widely utilised as fire-resistant dielectric coolants; in electrical equipment used in mining applicants, including transformers, capacitors, electric motors, and electromagnets. In addition, PCB's have been used in hydraulic fluids and heat-transfer fluids and are present in many oil-filled transformers. The U.S. Environmental Protection Agency (EPA) recently banned the manufacture of PCB's and equipment using PCB's, and imposed strict requirements on the continued use and disposal of existing PCB equipment. This manual discusses the EPA requirements, suggests ways to decrease the risks resulting from continued use of PCR equipment, and surveys the non-PCB equipment that is available as replacements for the PCB electrical equipment presently used in mines.]

Jan 1, 1980

By G. W. Jones

In a previous report,6 results were given that showed the amount of natural ventilation in a manhole having a capacity of 74.l cubic feet when the number of ventilation openings in the cover was varied. from no openings to a maximum of 48. The results showed that the ventilation (air changes per day) in the manhole was proportional to the area of the openings in the cover, and also that the number or area of the openings was the factor that chiefly affected the ventilation.

Jan 1, 1937

By C. Ozgen Karacan, William P. Diamond

In This Chapter [Measuring the gas content of coal Predicting gas emissions based on geologic and coal reservoir property data Determining the gas storage capacity of coalbeds and other gas-bearing strata Methane drainage borehole monitoring to forecast the remaining gas-in-place and the influence on mine emissions Forecasting gas emissions during mining as a function of mining parameters and Gas emission prediction based on numerical simulation] This chapter provides guidelines for determining the gas content of coalbeds, estimating the gas-in-place, and predicting gas flow and emissions before and during coal mining operations. The techniques are discussed briefly in the following sections. However, detailed information on the techniques is provided in the cited references. INTRODUCTION Coalbed methane, if not properly controlled in the underground mine environment, is a safety concern due to the potential risk for an explosion. This is a particular problem during longwall mining, where the high rate and volume of coal extraction can result in the release of large amounts of methane from the mined coalbed and other adjacent gas-bearing strata. The variability and potential hazards of these sometimes unexpectedly high gas flows provide the impetus to develop methods to predict methane emissions into the underground workplace. A forecast of the volume of gas that might be released during coal mining is helpful for designing ventilation systems and for implementing optimum methane drainage strategies to help mitigate expected gas emission problems. A complete assessment of the need for methane drainage prior to mine development generally requires both an empirical and a theoretical approach. If there are active mines in the general area with similar geologic conditions and coal characteristics, a review of gas problems in those mines provides an initial insight into the level of gas emissions to be expected at a new location. In addition, relatively simple methods exist to determine the in situ gas content (volume of gas per unit weight of coal) of the coalbeds in a particular mining area, as well as the gas-in-place (volume of gas in the coalbed(s) within a defined geographic area).

Jan 6, 2006

By James H. McCutchan

The small and remote mine operators must comply with the Federal Mine Safety and Health Administration regulation requiring them to train and maintain mine rescue teams. The alternative is for the operators to contract with established teams within two hours travel time of their mine. Many of these remote operations are too far away from established teams and have too few employees to make up the necessary teams. Many cannot comply with the regulation either from a manpower or economic standpoint. The Office of Arizona State Mine Inspector, under the direction of the Honorable James H. McCutchan, State Mine Inspector, entered into a contract with the Bureau of Mines to develop the concept of a volunteer mine rescue program. This program with the assistance of the mining industry and volunteer rescue organizations, has planned and instituted a statewide volunteer mine rescue organization. The trained and equipped volunteers are stationed throughout the state and can respond to a mine emergency within the time constraints.

Jan 1, 1984

By J. R. Thoenen

In the summer of 1937 the authors began a series of time studies of the various processes employed in' the production of crashed stone. These studies, made at quarries situated in the eastern and southeastern parts of the United States, have not been completed, but to make results available to the industry as early as possible, it was decided to publish summarizes of the studies made to January 1, 1939, as a series of progress reports. The first of these dealt with power-shovel loading and was issued as Report of Investigations 3461 in September 1939. The second, issued in September 1939 as Report of Investigations 3467, dealt with quarry haulage. The present report discusses analyses of time studies of primary drilling a t the same group of quarries. OBJECT OF STUDY Pressure of business problems frequently requires the entire attention of quarry management, and in consequence internal plant economies often are neglected. Also, operating officials absorbed in their local problems are prone to overlook possible economies that would attract attention immediately were they critically examining another plant. The authors felt that technical studies at a number of plants, made by impartial engineers, might disclose opportunities to reduce costs or improve efficiency in internal plant processes.

Jan 1, 1940

By R. Barany

This report contains the results of experimental work conducted by the Bureau of Mines to obtain the heats of formation at 298.15° K. of analcite, dehydrated analcite, lawsonite, anorthite, hexagonal anorthite, and leonhardite. Thermodynamic data for these minerals have applications in ceramics, extractive metallurgy, and particularly in geochemistry. Except for data on anorthite, no previous similar data existed. The present results will be a substantial aid in deriving the temperature-pressure-equilibrium relationships among these minerals. The heats of formation were determined by solution calorimetry, with hydrofluoric acid as the reaction medium. The results were expressed both in terms of the constituent oxides and in terms of the constituent elements. The heat of formation data were combined with related entropy values to obtain the free energies of formation at 298.15° K.

Jan 1, 1962