Search Documents

By Burton Scott

A device for detecting carbon monoxide at ppm levels is described which is based on the measurement of infrared absorption at 4.65 microns. The unique feature of the nondispersive infrared instrument is contained in the optical design which includes a confocal cavity, increasing the effective optical path length by a large factor, thus greatly reducing the required package size. The cavity has the effect of reducing the total amount of radiation passing to the detector, but at the same time increasing the percent attenuation observed when adding CO, by a factor called gain. The radiation is chopped by a filter wheel which contains narrow band filters at 4.0 and 4.65 microns. The resultant signal produced by the pyroelectric detector is demodulated by the electronics to product an automatic gain control signal, proportional to the total radiation, and a difference signal, proportional to the CO present. Tests of a breadboard model are described which show cavity gains of 10 with noise levels equivalent to 2 to 10 ppm CO.

Jan 1, 1975

By A. W. Deurbrouck

This report describes the washability characteristics of 18 coal samples taken from 11 drill hole cores from the San Juan Basin area of New Mexico and Colorado. The ash content of these coals could generally be substantially reduced by removing the heavy impurities. The coals were characteristically low in sulfur content; only one sample contained more than 1 percent sulfur after removing the sink-I.50 specific gravity material. The coals ranged in rank from subbituminous C to high volatile C; 11 of the samples were subbituminous A. Many of these core samples came from areas where very little fieldwork has been done; consequently, an outgrowth of this work has been an increase in known coal reserves of the San Juan Basin area.

Jan 1, 1972

By S. E. Khalafalla

In support of its goal to maintain an adequate supply of minerals to meet national economic and strategic needs, the Bureau of Mines has investigated a novel hydrometallurgical system with sulfur dioxide. Differential leaching with dissolved SO2 of manganese, nickel, and cobalt from their hydrous oxides was found to be very rapid and efficient--almost instantaneous and quantitative. In this method a given weight of mixed oxides previously ground to minus 200-mesh is slurried with a leach solution containing a specified quantity of dissolved SO2 for 10 minutes at room temperature and ambient pressure. An empirical leaching parameter, R, is defined as the ratio of the number of SO2 moles in the leaching solution to the weight of the metal oxide charge. Plots of the variation of metal extraction with the ratio R generate a series of sigmoidal-shaped curves, each of which is characteristic of a specific metal extraction. A threshold value of R is required to initiate the leaching of a given metal from the mixed oxides. Once this threshold is reached, the metal recovery can increase to more than 95 pct in very short times. For increasing values of R, the extractability of various metals by SO2 follows the order: Mn > Ni > Co >> Fe, Al, Cu. Differences in the threshold R values permit a variety of metal separations to be made simply by adjusting the quantity of SO2 in the contacting solution. Success in this leaching system depends upon comminuting the sea nodules to less than 0.149 mm (100-mesh). Above this critical size, leaching is slowed due to the inaccessibility of inner particle reacting groups to the SO2 leaching agent. This results in nonselective extraction and less extraction of preferred metal values. At or below 0.149 mm, leaching by SO, is possible with all its attributes of selectivity, sensitivity, and rapidity. Leaching with HC1 solutions of the same pH level as dissolved SO2 yielded mixed, slow, and incomplete metal extractions. This observation rules out any interpretation based on hydrogen ion as the leaching agent. The leaching curves resemble the complexometric titration curves of heavy metals with specific coordination species.

Jan 1, 1981

By Robert C. Hickman, Xavier B. Starnes

"The general location of the Kentucky, Fluorspar District and the Moore Hill fault area are shown in figure 1. An engineer3/ the Bureau of Mines visited the district in July 1942 and reported on the Moore Hill fault system. Subsequently the Bureau explored the Summers, Pepperbox, McCune, Eagle-Watson, Henry Watson, Davenport, Felix Tyner, and Eagle-Wring prop¬erties by core drilling. These properties and the principal faults are shown on figures 2 and 3.Collaboration of the Federal Geological Survey4/ was of great benefit, particularly in mapping the properties, determining the stratigraphy, and furnishing information on that and other geologic factors.Fluorite was noted as early as 1818 near Shawneetown in southern Illinois.5/ In 1835 an attempt was made to work deposit in Crittenden County, Kentucky, but interest centered chiefly upon the galena found with the fluorite. The first shipments of fluorspar from Kentucky wore made in 1373 from the Yandell mine of Crittendon County.6/ It is not known when the first work on the Moore Hill fault was done, but it seems probable that the Cullen-Eagle and Nancy Hanks were being ,worked in 1900. Gravel spar was found on the surface at the Two Brothers mine in 1904,7/ and the main shaft was started in 1914; work also began at .the Davenport in 1914, and in 1917 the Eagle-Watson was in production. A shaft was gunk on the Pepperbox in 1918, and in 1922 fluorspar was found and work was started on the Summers property. In 1924 work began at the McCune, Felix Tyner, Eagle-Wring, and probably the Hicks properties.No Good approximate record of production from each property on the Moore Hill fault system is obtainable, but an estimate based upon all data available is as follows:"

Sep 1, 1946

By Joseph M. Kuchta

The limits of flammability and minimum autoignition temperature of a fuel are important elements in assessing fire and explosion hazards that may exist when using or handling the fuel. The limits of flammability define the range of compositions of the fuel gas or vapor mixed with an oxidant through which a flame, initiated by an outside energy source such as an electrical spark, can propagate. The minimum autoignition temperature (M.A.I.T.) is the lowest temperature at which the fuel vapors ignite spontaneously in a specified medium; in this case the ignition energy is supplied by the heat content of tae environment. This temperature is also referred to as S.I.T. value by some authors. Because the autoignition of a fuel also depends on the time interval during which the fuel is subjected to heat, ignition delays are significant. Ignition delay is defined here as the total time elapsed between the introduction of the liquid fuel into the oxidizing atmosphere and the appearance of a flame. This time interval includes both the physical and chemical processes leading to ignition. The ignition delay is usually maximum at the M.A.I.T, and decreases as the temperature of the system is increased. The flash point and the fire point are also useful in assessing the fire and explosion hazards of a fuel. The flash point is the lowest temperature at which saturated, flammable fuel vapor-air mixtures are formed at atmospheric pressure and, therefore, it is essentially the lower limit of flammability

Jan 1, 1962

By Geo. S. Krueger

This paper, describing mining methods and costs at the Judge mine Park City, Utah, is one of a series being prepared by the Bureau of Mines on mining practices in the United states. ACKNOWLEDGMENTS The writers acknowledge the assistance of E. D. Gardner, supervising engineer, Southwest Experiment Station, Bureau of Mines; Paul H. Hunt, mine manager, Park Utah Consolidated Mines Co.; Wm. Osika, chief mine accountant; and Eric Neilson, assistant master mechanic of the mine.

Jan 1, 1938

By Lindsay D. Norman

Computer models for simulating the construction and for calculating the properties of particulate solids in two- and three-dimensional systems (coverings of circles and packings of spheres, respectively) were developed. By simulating the physical process of constructing circle coverings and sphere packings, in which the circles or spheres were randomly selected from many different distributions of sizes, physically realizable loose random assemblies were simulated whose physical and geometrical properties were predictable with the computer. Many of these properties, such as the number of contacts, are extremely-difficult to measure accurately, or considerable ingenuity is required in their determination. All of these properties were easily and accurately calculated by the computer models for many different coverings and packings constructed from equal, discrete, uniform, and log-normal distributions of particles. In addition to the loose random assemblies, dense random covering and packing constructions were simulated whose properties are ideal upper limits for those of the loose random coverings and packings. The properties of the dense random coverings and packings, heretofore only obtainable by theoretical analysis, were also simply obtained. The statistical geometry of loose random coverings and packings was studied, and several new interpretations of the area-covering or space-filling requirements in these systems were made. In two dimensions, it was found that the properties of all loose random coverings are predictable by taking suitably weighted averages of the corresponding properties of just four kinds of polygons whose edges are defined by connecting the centers of mutually tangent circles in the covering. The distributions of these polygons that permit area-covering were determined, and empirical equations for predicting the density, average coordination number, and average pore area in loose and dense random coverings were formulated. The properties of loose packings were determined by performing a simplicial division of the computer-simulated assemblies to produce a unique set of minimum volume, space-filling tetrahedra whose edges connected the sphere centers in each packing. A simple empirical equation was formulated that permits the calculation of the average number of contacts in any sphere packing, random or regular. Some of the statistical geometrical properties of the simplicial tetrahedra in the computer-simulated packings were analyzed. The tetrahedron edge length distributions in all the loose random packings were nearly identical when the edges were presented in terms of sphere diameters, regardless of the sphere population in the packing. Moreover, the gap lengths in the loose packings were to an excellent approximation representable by a uniform distribution of sizes. The distributions of spheres in tetrahedra resulting from the simplicial division of the loose random packings also existed in the tetrahedra in dense random packings. These observations were employed in developing a unique method for predicting the geometrical properties of loose random packings without simulating the assembled packing. Instead, the space-filling simplicial graph could be predicted for any given density of packing of any sphere population. The cumulative packing properties of these tetrahedra were shown to be nearly identical to those calculated by all loose random packing simulations attempted in this investigation. The simplicial tetrahedra completely describe a packing and can therefore be used to predict all properties of interest.

Jan 1, 1971

By F. A. Penning

Improved skips, with lightweight cylindrical bodies, have made a significant contribution to advancing mine hoisting technology. New concept skips of aluminum bodies with rubber lining; fiberglas bodies with polyurethane liners have been designed and fabricated for field testing at an operating mine. New design, adjustable guide rollers have shown improved ride characteristics with noticeably less wear. Major reductions have been made in stress levels and stress concentrations. Field experience has shown the practicality of the approach. Guide alignment has been measured using the Guide Alignment Measuring System (GAMS). Analysis has been applied to interpret the data. Field measurements in an operating shaft and a test tower have shown the agreement in data from GAMS and plumb wires. Reproducibility has been demonstrated. The data are useful to realign shafts, to use as s maintenance tool, and to evaluate the maximum safe hoisting speeds. The surveys are made at several hundred feet per minute and the system is self-contained. Dynamics of skip-guide interaction has been analyzed using the computer program SKIP II. The effects of speed, weight, type of guides, kind of misalignment have been studied. Resonance has been demonstrated and factors that eliminate resonance have been identified. Data from the GAMS surveys are applicable to the SKIP II program. Interaction between the hoist rope and the mine conveyance has also been studied. Computer programs and closed-form solutions are presented. Economic impact of lightweight skips is presented for an existing mine and for a new mine. Reduction in rope size has a profound effect when using a lightweight skip for the same capacity. Increased productivity can be realized by keeping maximum rope pull the same while increasing skip capacity. Examples and charts project the significant savings in capital expenditure for new installations.

Jan 1, 1985

By Michael Kaplan

An investigation was conducted of the use of a mechanical rock splitter as the primary means for rock fragmentation in underground hard rock mining systems. Analyses and scale model tests showed that reasonably sized splitters that could be mounted on the booms of conventional drill jumbos were capable of fragmenting over a ton of rock per cycle. Detailed drill-split mining systems were developed for entry development, room and pillar, bench mining, and cut and fill mining. Economic analyses of these systems showed them to be generally competitive with conventional drill-blast methods. Except for bench mining, drill-split offered substantial cost savings over drill-blast. The investigation also included a technical evaluation of the mechanical splitter, an analysis of health and safety, and a determination of the potential applicability of drilling and splitting.

Jan 1, 1979

The works recorded in this Test Report have been performed by Rade Roncar - Electrotechnical Institute of Zagreb, SFR Yugoslavia in collaboration with Bureau of Mines. The main objective of these investigations was to investigate the possibility of fabrication of thin-walled square enclosures of satisfactory safety factor in accordance with requirements of effective technical regulations. The results and the investigations can be divided in three main fields: - investigations of thin-walled enclosures with the view of determination of pressures causing technological deformations before performing tests in accordance with effective applicable regulations, - finding the safety factor by means of tests of metal-foam pressure vents, - comparison of enclosures with and without pretreatment by technological deformation.

Jan 1, 1987

By John C. Holtz

Information on the gaseous products from the detonation of explosives has been obtained in two ways. In the first, the atmosphere in mines is analyzed after blasting, aid in the second, the gases found after detonating an explosive in a testing apparatus are analyzed. The Bureau of Mines, in

Jan 1, 1940

By John C. Holtz

Information on the gaseous products from the detonation of explosives has been obtained in two ways. In the first, the atmosphere in nines is analyzed after blasting, aid in the second, the gases found after detonating an explosive in a testing apparatus are analyzed. The Bureau of Mines, in

Jan 1, 1940

By W. H. Ode

In 1949 the Coal Committee of the Economic Commission for Europe, Geneva, Switzerland, established a Classification Working Party, to develop an international system for classifying coal. This project was necessitated by the increased trade in coal among various nations following World War II. Although national classification systems existed, they had been developed to cover the characteristics of domestic coals without reference to coals of other countries. Different terms for describing similar or identical coals in each nation caused confusion in evaluating coals shipped in international trade. Experts from Austria, Belgium, Bulgaria, Czechoslovakia, Denmark, the Federal Republic of Germany, France, Greece, Hungary, Italy, the Netherlands, Poland, Sweden, the Union of Soviet Socialist Republics, East Germany, the United Kingdom, the United States of America, and Yugoslavia participated in various stages of the classification work. Walter A. Selvig was appointed by the Bureau of Mines as the technical expert to represent the United States because of his experience in developing and standardizing methods of analyzing and classifying American coals. He served on the Classification Working Party until his retirement from the Bureau of Mines early in 1956. Extensive laboratory work was done in connection with the classification studies at the Pittsburgh Experiment Station of the Bureau of Mines.

Jan 1, 1958

By R. F. Zaffarano

Data presented on the physical characteristics of the reservoir oil, Aneth field, represent the initial phase of a study of Paradox basin reservoir oils being made by petroleum engineers of the Federal Bureau of Mines, Petroleum Research Center, Laramie, Wyo. The purpose of the study is to determine the original reservoir-oil characteristics in several important new discoveries in the Paradox Basin and to investigate correlations between the properties of these reservoir oils and structural or areal position within the basin, If migration is limited and oil accumulates near its source, then it seems probable that few differences should be found in the composition and characteristics of reservoir oils occurring in given age rocks and within the confines of a geological basin. Within these limits, conditions that effected the formation of oil and its transfer from parent to storage rocks probably were rather uniform in an area the size of most of our geological basins. However, if oils should migrate considerable distances, it seems logical to expect that the relative quantities of gas and liquid components may differ in traps occurring along the direction of migration, corresponding with the theory of differential entrapment (5).4/

Jan 1, 1959

By B. J. Moore

The Bureau of Mines has estimated helium resources of the United States at 727 billion cubic feet as of January 1, 1979. These resources are divided into four categories in decreasing degrees of assurance of their existence: (1) Helium in storage and in measured natural gas reserves, 185 billion cubic feet; (2) helium in indicated natural gas resources, 150 billion cubic feet; (3) helium In hypothetical natural gas resources, 186 billion cubic feet; and (4) helium in speculative natural gas resources that makes up the remaining 206 billion cubic feet. The identified helium reserves, which are made up of that in measured and indicated natural gas categories, are further divided into depleting, non- depleting, and stored classifications. The depleting resources are those that are associated with natural gasfields that are, or will be, produced for the natural gas they contain. All of the helium in undiscovered natural gas resources are included in this classification. These depleting resources comprise 600 billion cubic feet of the total resource base. The nondepleting helium resources are estimted tototal 88 billion cubic feet. There is 39 billion cubic feet of helium in storage in Cliffside gasfield near Amarillo, Tex.

Jan 1, 1980

By Francis E. Federspiel

In 1984 and 1985, at the request of the U.S. Forest Service, the U.S. Bureau of Mines examined the 87,720-acre South Boise Yuba study area (formerly known as RARE II Wilderness Recommended area I-4553) to evaluate mineral resources. The study area and additions are in Blaine, Camas, and Elmore Counties, 10, about 60 mi east of Boise. Granitic rocks of the Cretaceous age Idaho Batholith occupy the western two-thirds of the study area. A Tertiary age granitic complex has intruded, and broken into small blocks, Paleozoic age sedimentary rocks in the eastern third of the study area. Tertiary Challis Volcanics overlie both of these rock types. Principal mineralized structures are gold-and silver-bearing quartz veins and shear zones trending northwest to easterly in the Cretaceous granitic rocks. Copper, lead, and zinc are accessory metals in many mineralized structures.

Jan 1, 1987

By John C. Machisak

THIS PUBLICATION presents injury experience and employment data for the nonmetal mining industry in the United States for 1960. Data for the mines and mills are presented separately, as shown in the list of tables. The Bureau of Mines is authorized to send questionnaires to the nonmetal mining industry for their voluntary submission of injury and employment data. As the information submitted contributes largely to the promotion of safety in the industry, special effort has been made to ma e these questionnaires as complete as possible.

Jan 1, 1963

By F. L. Wideman

This paper lists resources of sulfur in Wyoming, Colorado, Utah, New Mexico, and Arizons, an area comprising approximately 522,600 square miles, Sources of sulfur occuring within the region are sulfur are, pyrite and pyritic ores, and natural gases and petroleum. Data concerning these sources are presented on a statewide basis. Some of the known deposits of sulfur ore are surficial and of fumerole origin; other deposits have resulted from oxidation of pyrite or sulfide ores of copper, lead, and zinc. The deposits are small and the sulfur is distributed erratically in them. There is a small production from some of the deposits, and the material produced is used as soil conditioner.

Jan 1, 1957

By D. G. Willard

The U.S. Department of Interior, Bureau of Mines has evaluated the potential resource and annual availability of cobalt from 27 deposits or districts in 11 market-economy countries. More than 95 pct of primary cobalt production from market-economy countries, mainly byproduct output from copper and nickel operations, was analyzed. Approximately 1,200,000 mt of cobalt is potentially recoverable at the demonstrated resource level. Very large additional resources exist, especially in laterite deposits, but are at the inferred level. The producing operations evaluated in this study are expected to produce about 19,000 mt of cobalt in 1989, significantly less than the available capacity of about 31,000 mt. More than 14,000 mt per year of cobalt is produced from copper-cobalt deposits in Zaire and Zambia, of which 11,000 mt can be produced at a copper price of $O.60jlb or less with a O-pct discounted cash-flow rate of return (DCFROR). Approximately 4,400 mt of cobalt is produced annually from nickel-cobalt deposits in six countries, of which about 1,800 mt (in Canada and Brazil) could be produced at a nickel price of $1.50jlb or less at a D-pct DCFROR. Approximately 200 mt per year of cobalt is produced from a cobalt mine in Morocco. Most of the evaluated nonproducing operations and prospects that could potentially produce cobalt as a principal product or byproduct would require a total cost (including a 15 pct-DCFROR) significantly exceeding January, 1989 market prices of the principal commodities. Principal-commodity dependence, transportation routes, cobalt toxicity, and other issues that could affect the availability of cobalt are addressed herein.

Jan 1, 1991

By Maria I. De Rosa

Table 46 and figure 16 show the number of fires and fire injuries for metal/nonmetal mills by state during 1990-2001. Table 46 also shows the injury risk rates, employees' working hours, and lost workdays. In all, 77 fires occurred in 26 states. Thirty-seven of the fires caused 41 injuries and 1 fatality (including 5 fires and 3 injuries involving contractors). The yearly average was 6.4 fires and 3.4 injuries. Fifty-four fires with 26 injuries and 1 fatality occurred at metal mills; 23 fires with 15 injuries occurred at nonmetal mills. The Ewhr value was 845 x 106 hr (Irr = 0.01), and the LWD value was 6,681. Minnesota had the most fires (16 fires and 5 injuries), followed by Arizona (9 fires and 3 injuries), Wyoming (8 fires and 3 injuries), Nevada (7 fires, 4 injuries, and 1 fatality), and Texas (4 fires and 7 injuries). Of these states, Texas had the highest injury risk rate value (Irr = 0.033). Table 47, partly illustrated in figure 17, shows the number of fires, fire injuries, fire fatalities, risk rates, employees' working hours, and lost workdays by time period. The number of fires increased slightly during the second period, then decreased during the remaining periods. The number of fire injuries show a decrease during most of the periods (an increase is seen during the third period), accompanied by a decline in employees' working hours during most of the periods. The Irr values follow patterns similar to those shown by the injury values. Tables 48-53 show the number of fires by ignition source, method of detection and suppression, equipment involved, location, and burning material by time period. Figure 18 shows the major variables related to fires for 1990-2001. Table 54 shows the number of fire injuries per number of fires causing injuries and total fires by year, ignition source, equipment involved, and location.

Jan 1, 2004