Search Documents

By S. E. Khalafalla

In support of its goal to maintain an adequate supply of minerals to meet national economic and strategic needs, the Bureau of Mines has investigated a novel hydrometallurgical system with sulfur dioxide. Differential leaching with dissolved SO2 of manganese, nickel, and cobalt from their hydrous oxides was found to be very rapid and efficient--almost instantaneous and quantitative. In this method a given weight of mixed oxides previously ground to minus 200-mesh is slurried with a leach solution containing a specified quantity of dissolved SO2 for 10 minutes at room temperature and ambient pressure. An empirical leaching parameter, R, is defined as the ratio of the number of SO2 moles in the leaching solution to the weight of the metal oxide charge. Plots of the variation of metal extraction with the ratio R generate a series of sigmoidal-shaped curves, each of which is characteristic of a specific metal extraction. A threshold value of R is required to initiate the leaching of a given metal from the mixed oxides. Once this threshold is reached, the metal recovery can increase to more than 95 pct in very short times. For increasing values of R, the extractability of various metals by SO2 follows the order: Mn > Ni > Co >> Fe, Al, Cu. Differences in the threshold R values permit a variety of metal separations to be made simply by adjusting the quantity of SO2 in the contacting solution. Success in this leaching system depends upon comminuting the sea nodules to less than 0.149 mm (100-mesh). Above this critical size, leaching is slowed due to the inaccessibility of inner particle reacting groups to the SO2 leaching agent. This results in nonselective extraction and less extraction of preferred metal values. At or below 0.149 mm, leaching by SO, is possible with all its attributes of selectivity, sensitivity, and rapidity. Leaching with HC1 solutions of the same pH level as dissolved SO2 yielded mixed, slow, and incomplete metal extractions. This observation rules out any interpretation based on hydrogen ion as the leaching agent. The leaching curves resemble the complexometric titration curves of heavy metals with specific coordination species.

Jan 1, 1981

By Joseph M. Kuchta

The limits of flammability and minimum autoignition temperature of a fuel are important elements in assessing fire and explosion hazards that may exist when using or handling the fuel. The limits of flammability define the range of compositions of the fuel gas or vapor mixed with an oxidant through which a flame, initiated by an outside energy source such as an electrical spark, can propagate. The minimum autoignition temperature (M.A.I.T.) is the lowest temperature at which the fuel vapors ignite spontaneously in a specified medium; in this case the ignition energy is supplied by the heat content of tae environment. This temperature is also referred to as S.I.T. value by some authors. Because the autoignition of a fuel also depends on the time interval during which the fuel is subjected to heat, ignition delays are significant. Ignition delay is defined here as the total time elapsed between the introduction of the liquid fuel into the oxidizing atmosphere and the appearance of a flame. This time interval includes both the physical and chemical processes leading to ignition. The ignition delay is usually maximum at the M.A.I.T, and decreases as the temperature of the system is increased. The flash point and the fire point are also useful in assessing the fire and explosion hazards of a fuel. The flash point is the lowest temperature at which saturated, flammable fuel vapor-air mixtures are formed at atmospheric pressure and, therefore, it is essentially the lower limit of flammability

Jan 1, 1962

By R. D. Rosenkranz

The Bureau of Mines has investigated the availability of copper from 272 deposits in market economy countries. The deposits studied have demonstrated resources totaling 413 million metric tons of contained copper and account for more than 90 pct of the reserve base for market economy countries. Using data gathered as part of its Minerals Availability Program, the Bureau performed geologic, engineering, and economic evaluations in order to determine the copper production potential of each deposit. At the 1981 copper market price of $0.85/lb, the deposits studied could economically produce an estimated 88 million metric tons of copper (allowing for profit computed at a 15-pct rate of return), primarily from mines operating at the time of the study (1981). At this price, producing mines in market economy countries could economically produce only 2.1 million metric tons of refined copper per year. However, actual 1981 production was 6.2 million metric tons, indicating that many mines continued to operate even though they were unable to cover all production costs. For U.S. producing mines, the estimated average cost of production per pound (including profit at a 15-pct rate of return) was $0.15 higher than the average cost in other market economy countries.

Jan 1, 1983

By F. A. Penning

Improved skips, with lightweight cylindrical bodies, have made a significant contribution to advancing mine hoisting technology. New concept skips of aluminum bodies with rubber lining; fiberglas bodies with polyurethane liners have been designed and fabricated for field testing at an operating mine. New design, adjustable guide rollers have shown improved ride characteristics with noticeably less wear. Major reductions have been made in stress levels and stress concentrations. Field experience has shown the practicality of the approach. Guide alignment has been measured using the Guide Alignment Measuring System (GAMS). Analysis has been applied to interpret the data. Field measurements in an operating shaft and a test tower have shown the agreement in data from GAMS and plumb wires. Reproducibility has been demonstrated. The data are useful to realign shafts, to use as s maintenance tool, and to evaluate the maximum safe hoisting speeds. The surveys are made at several hundred feet per minute and the system is self-contained. Dynamics of skip-guide interaction has been analyzed using the computer program SKIP II. The effects of speed, weight, type of guides, kind of misalignment have been studied. Resonance has been demonstrated and factors that eliminate resonance have been identified. Data from the GAMS surveys are applicable to the SKIP II program. Interaction between the hoist rope and the mine conveyance has also been studied. Computer programs and closed-form solutions are presented. Economic impact of lightweight skips is presented for an existing mine and for a new mine. Reduction in rope size has a profound effect when using a lightweight skip for the same capacity. Increased productivity can be realized by keeping maximum rope pull the same while increasing skip capacity. Examples and charts project the significant savings in capital expenditure for new installations.

Jan 1, 1985

By John C. Holtz

Information on the gaseous products from the detonation of explosives has been obtained in two ways. In the first, the atmosphere in mines is analyzed after blasting, aid in the second, the gases found after detonating an explosive in a testing apparatus are analyzed. The Bureau of Mines, in

Jan 1, 1940

By John C. Holtz

Information on the gaseous products from the detonation of explosives has been obtained in two ways. In the first, the atmosphere in nines is analyzed after blasting, aid in the second, the gases found after detonating an explosive in a testing apparatus are analyzed. The Bureau of Mines, in

Jan 1, 1940

By Francis E. Federspiel

In 1984 and 1985, at the request of the U.S. Forest Service, the U.S. Bureau of Mines examined the 87,720-acre South Boise Yuba study area (formerly known as RARE II Wilderness Recommended area I-4553) to evaluate mineral resources. The study area and additions are in Blaine, Camas, and Elmore Counties, 10, about 60 mi east of Boise. Granitic rocks of the Cretaceous age Idaho Batholith occupy the western two-thirds of the study area. A Tertiary age granitic complex has intruded, and broken into small blocks, Paleozoic age sedimentary rocks in the eastern third of the study area. Tertiary Challis Volcanics overlie both of these rock types. Principal mineralized structures are gold-and silver-bearing quartz veins and shear zones trending northwest to easterly in the Cretaceous granitic rocks. Copper, lead, and zinc are accessory metals in many mineralized structures.

Jan 1, 1987

The works recorded in this Test Report have been performed by Rade Roncar - Electrotechnical Institute of Zagreb, SFR Yugoslavia in collaboration with Bureau of Mines. The main objective of these investigations was to investigate the possibility of fabrication of thin-walled square enclosures of satisfactory safety factor in accordance with requirements of effective technical regulations. The results and the investigations can be divided in three main fields: - investigations of thin-walled enclosures with the view of determination of pressures causing technological deformations before performing tests in accordance with effective applicable regulations, - finding the safety factor by means of tests of metal-foam pressure vents, - comparison of enclosures with and without pretreatment by technological deformation.

Jan 1, 1987

By A. W. Deurbrouck

This report describes the washability characteristics of 18 coal samples taken from 11 drill hole cores from the San Juan Basin area of New Mexico and Colorado. The ash content of these coals could generally be substantially reduced by removing the heavy impurities. The coals were characteristically low in sulfur content; only one sample contained more than 1 percent sulfur after removing the sink-I.50 specific gravity material. The coals ranged in rank from subbituminous C to high volatile C; 11 of the samples were subbituminous A. Many of these core samples came from areas where very little fieldwork has been done; consequently, an outgrowth of this work has been an increase in known coal reserves of the San Juan Basin area.

Jan 1, 1972

By John S. Berber

Acids, neutral oils, and pitch were produced by distillation of low-temperature lignite tar and processed to upgrade them into more valuable products: The acids were separated from the distillate and catalytically dealkylated to produce phenol, cresol, and xylenol. Aromatic and naphthene fractions of the neutral oil were converted into phthalic and maleic anhydrides by catalytic hydrodealkylation and vapor- phase oxidation. Paraffins and n-olefins from the neutral oil were processed into alkybenzene sulfonate, a biodegradable substance. Aromatic materials from the neutral oil were also extracted with organic compounds and the extract hydrogenated under pressure to produce jet fuel. The pitch was processed by various means to change its characteristics and make it suitable for similar applications as high- temperature tar pitch, including preparation of carbon black and metallurgical electrodes. In most cases, products obtained from the low-temperature tar were examined for physical and chemical characteristics and for potential commercial utility. Information obtained from this research would be helpful if a new coal- chemical industry based on tar utilization were established.

Jan 1, 1973

By J. Bootle

Marrow vein deposits will continue to be an important source of valuable minerals. Productivity per manshift is not keeping pace with operating costs. Increased mechanization of stoping operations must be obtained to create greater productivity at a reduced cost per ton. This application of mechanization may be to either present methods or to newly developed concepts. The total mine unit operations will be effected by increased productivity. Two approaches to increasing the mechanization of narrow vein stoping were studied with the intention of increasing stope productivity and decreasing stoping costs. A method of bringing efficient rubber-tired equipment into narrow cut and fill stopes was designed. It proposes to provide stope access by way of a ramp constructed on the stope fill. Impact breaking equipment was studied and specific applications proposed.

Jan 1, 1977

By B. J. Moore

The Bureau of Mines has estimated helium resources of the United States at 727 billion cubic feet as of January 1, 1979. These resources are divided into four categories in decreasing degrees of assurance of their existence: (1) Helium in storage and in measured natural gas reserves, 185 billion cubic feet; (2) helium in indicated natural gas resources, 150 billion cubic feet; (3) helium In hypothetical natural gas resources, 186 billion cubic feet; and (4) helium in speculative natural gas resources that makes up the remaining 206 billion cubic feet. The identified helium reserves, which are made up of that in measured and indicated natural gas categories, are further divided into depleting, non- depleting, and stored classifications. The depleting resources are those that are associated with natural gasfields that are, or will be, produced for the natural gas they contain. All of the helium in undiscovered natural gas resources are included in this classification. These depleting resources comprise 600 billion cubic feet of the total resource base. The nondepleting helium resources are estimted tototal 88 billion cubic feet. There is 39 billion cubic feet of helium in storage in Cliffside gasfield near Amarillo, Tex.

Jan 1, 1980

By Joseph A. Cavallaro

This report describes the timed release analysis technique that was developed to serve as a tool for assessing the froth flotation cleaning potentials of fine-size coals. Using this developed technique, 16 coals from 10 different coalbeds were tested. All of the coals included in this study were quite amenable to froth flotation with float coal yields ranging from 80.7 to 99.5 percentage points. Float-and-sink analyses of the coals tested are shown to be of limited value in predicting froth flotation cleaning potential. Generally the float-and-sink analyses indicated a better product could be obtained than froth flotation could provide; although, in four of the coals tested froth flotation results were superior to those expected from the gravimetric analysis. The fixed carbon content of the samples collected was found to correlate with the floatability of the coals. The higher rank coals were the most readily floatable coals while the lower rank coals did not respond quite as well to flotation.

Jan 1, 1965

By Geo. S. Krueger

This paper, describing mining methods and costs at the Judge mine Park City, Utah, is one of a series being prepared by the Bureau of Mines on mining practices in the United states. ACKNOWLEDGMENTS The writers acknowledge the assistance of E. D. Gardner, supervising engineer, Southwest Experiment Station, Bureau of Mines; Paul H. Hunt, mine manager, Park Utah Consolidated Mines Co.; Wm. Osika, chief mine accountant; and Eric Neilson, assistant master mechanic of the mine.

Jan 1, 1938

By John C. Machisak

THIS PUBLICATION presents injury experience and employment data for the nonmetal mining industry in the United States for 1960. Data for the mines and mills are presented separately, as shown in the list of tables. The Bureau of Mines is authorized to send questionnaires to the nonmetal mining industry for their voluntary submission of injury and employment data. As the information submitted contributes largely to the promotion of safety in the industry, special effort has been made to ma e these questionnaires as complete as possible.

Jan 1, 1963

By Michael Kaplan

An investigation was conducted of the use of a mechanical rock splitter as the primary means for rock fragmentation in underground hard rock mining systems. Analyses and scale model tests showed that reasonably sized splitters that could be mounted on the booms of conventional drill jumbos were capable of fragmenting over a ton of rock per cycle. Detailed drill-split mining systems were developed for entry development, room and pillar, bench mining, and cut and fill mining. Economic analyses of these systems showed them to be generally competitive with conventional drill-blast methods. Except for bench mining, drill-split offered substantial cost savings over drill-blast. The investigation also included a technical evaluation of the mechanical splitter, an analysis of health and safety, and a determination of the potential applicability of drilling and splitting.

Jan 1, 1979

By P. M. Daling

This report, sponsored by the U.S. Bureau of mines, presents the results of an examination of available safety assessment methods and their applicability to the mining industry. Standard safety analysis procedures were evaluated for relevance to the mining industry and mire operators' needs. The major safety concerns and needs of mine operators were identified through telephone contacts and a visit to a mine site. Safety assessment methods recommended for use by the mining Industry were also investigated for potential adaptability to a user-interactive computer system. Several methods were determined to be Immediately transferrable to the mining industry; these techniques are described in a user's handbook produced as part of this project. The handbook gives detailed instructions on appropriate application and utilization of these methods. Other techniques will require further development before they can be effectively transferred to the mining Industry. These methods, their advantages, disadvantages and resource requirements are described in the final project report. Recommended system safety analysis techniques facilitate an evaluation of total mine system safety and a determination of safety-related interactions among systems within a mine. The application of these methods to the mining industry could result In reductions in both the frequency and the consequences of mine accidents.

Jan 1, 1983

By M. R. Geer

The widespread adoption during the past decade of the dense-medium process for cleaning coal increases the need for technologic studies of the process. Such studies provide information that will insure maximum usefulness of this process in its present form and may well lead to substantial improvements in design and opera¬tion. The Bureau of Mines has published the results of cleaning trials on a wide variety of coals in two dense-medium pilot plants5/ and reported the recovery of coal from waste by dense-medium treatment.6./ The present report deals with the viscosity of magnetite dense medium, an important subject about which virtually nothing has been published. Specifically, the report concerns methods for measuring viscosity, the influence of various medium contaminants on viscosity, the effect of viscosity on cleaning results, and the influence of viscosity on consumption of medium. Cleaning trials on four coals of varied density composition in a pilot plant, using mediums of different viscosities, showed a steady reduction in cleaning efficiency with increasing viscosity in every instance. However, the behavior of each coal in a viscous medium was distinctly individual. With one, an increase of only 1 centipoise in viscosity caused a reduction in recovery efficiency of 7.7 percent, whereas the same increase in viscosity with another reduced recovery efficiency only 2.7 percent.

Jan 1, 1957

By John C. Machisak

THIS PUBLICATION presents injury experience and employment data for the nonmetal mining industry in the United States for 1960. Data for the mines and mills are presented separately, as shown in the list of tables. The Bureau of Mines is authorized to send questionnaires to the nonmetal mining industry for their voluntary submission of injury and employment data. As the information submitted contributes largely to the promotion of safety in the industry, special effort has been made to make these questionnaires as complete as possible.

Jan 1, 1963

By Donald I. Bleiwas

The U.S. Bureau of Mines has evaluated the potential availability of nickel from 36 deposits or districts in 16 market-economy countries (MECs), analyzing more than 95 percent of production in those countries. This study indicates the quantity of nickel available on the basis of net production costs and total costs with a 0-pct and a 10-pct discounted cash flow rate of return (DCFROR). Costs of production are expressed in dollars per pound of recovered nickel. The study also indicates sensitivities of the cost of production to energy, labor, and other factors. The studied deposits and properties contain approximately 33 Mmt of recoverable nickel. About 26 Mmt of nickel is potentially recoverable from laterite deposits, of which 4.5 Mmt can be produced at $2.50/lb or less with a 0-pct DCFROR. Approximately 7 Mmt of nickel is potentially recoverable from sulfide deposits, of which about 6.3 Mint could be produced at $2.50/lb or less at a 0-pct DCFROR. The price of nickel averaged above $6.00/lb in 1988. Sensitivity studies performed for both laterite and sulfide deposits indicate that the total cost of producing nickel from laterites is most sensitive to increases in energy costs and that the total cost of producing nickel from sulfide deposits is most sensitive to increases in labor costs; sulfides are also affected by changes in revenues from byproducts.

Jan 1, 1991