Search Documents

By Kenneth L. Whitehead

After many years of research, the occurrence of pneumoconiosis, black lung disease, among miners has been related to the mass of respirable coal dust to which mining personnel have been exposed. Congress passed Public Law No. 91-173 in 1969, which limited the dust concentration of respirable dust allowed in the mine working areas to 2.0 mg /M3 as of December 31, 1972. As a result of these restrictions, much work has been done in determining methods of either eliminating or suppressing respirable dust. The purpose of this project is to determine the state-of-the-art in continuous mining machine bit technology, particularly with regard to dust production.

Jan 1, 1973

By G. R. Smith

This report describes research carried out by the Bureau of Mines to develop new technology for electrorefining metals at much higher current densities than those normally used in commercial practice, preliminary studies using rotating-ring and cylinder electrodes to increase the mass transport of copper are discussed. Following this work, single- and multichannel cells were developed that utilized a high electrolyte flow in the channels formed by the anode-cathode pairs. Using these cells, copper was successfully refined at current densities in the range of 70 to 300 amp/ft2. The effects of flow rate, electrolyte composition, and grain-refining and leveling agents on the morphology and purity of electrodeposited copper were determined.

Jan 1, 1979

By R. W. Stahl

The use of continuous mining machines has greatly minimized the necessity for blasting in coal mines, even during pillar recovery; however, explosives are still used to blast stumps. The use of improper blasting materials, improper procedures, or both has caused mine explosions and fires, with loss of life and property damage. Researchers and manufacturers are continuously improving explosives and blasting accessories; use of the more recently developed materials will make the blasting operation safer. Extreme caution is mandatory when blasting stumps, as the ignition of methane or coal dust may trigger an explosion or cause a fire. Since the blasting of stumps will no doubt continue, although often unnecessarily, this paper summarizes recent findings published by the Bureau of Mines and recommends safer methods.

Jan 1, 1962

By W. M. Bangert, F. S. Boericke

"INTRODUCTION Previous investigations of the Boulder City station of the Bureau of Mines have demonstrated that low-grade domestic chromite concentrates can be roasted with carbon to obtain selective reduction of the contained iron, and that the reduced iron can be removed by acid leaching of the roasted products to produce residues with higher chromium iron ratios. Thus, some chromite ores or concentrates that originally contain too much iron to be acceptable for the production of ferrochrome can, by this treatment, be rendered marketable as ""high-grade"" chromite. 3/The present report supplements the earlier work of the Bureau and re¬cords the results of small-scale laboratory tests investigating the effects of:1. Temperature and time of the reducing roast.2. Chromite and carbon particle size.3. Ratio of carbon to chromite in the initial roast mixture.4. Variations in the alumina and silica content of the ore.5. Back-oxidation of the roast product.6. Temperature and time of leaching .of roast product.This work differs from that done previously in that particular emphasis was placed on roast mixtures containing just enough carbon for the reduction of the iron in the chromite, whereas some two and one-half times this amount of carbon was used in the earlier work.In addition to these tests, the mechanism of the production reactions was examined for the purpose of explaining the precance of acid-soluble chromium, which occurs under certain conditions of chromite reduction."

Jul 1, 1945

By J. J. Taber

Gas and water permeabilities of a large number of samples from the Pittsburgh and Pocahontas coals were measured at various overburden and mean flow pressures. A wide variation in the air and water permeabilities was obtained for each type of coal. Overburden pressure has the most significant effect on the single-phase permeability. Considerable hysteretic effect was observed for both air and water permeabilities. Gas permeabilities are affected to a lesser degree by mean flow pressures above atmospheric. However, at subatmospheric mean pressures, appreciable increase in permeability occurs for low permeability samples. Air and water relative permeabilities were also measured for numerous samples of Pittsburgh and Pocahontas coals. Tests were performed under steady-state conditions for both drainage and imbibition cycles. Results indicate that the flow of gas is greatly reduced during the latter process, whereas it is largely undiminished over a wide water-saturation range during drainage. It is also shown that imbibition saturation distributions obtained from liquid-water imbibition as opposed to water-vapor adsorption produce gas permeability curves of radically different character. The effective permeabilities to both gas and water were significantly reduced with the application of overburden pressures in the range of 0 to 1,000 psig, but the general shapes of the relative permeability curves remained the same.

Jan 1, 1974

By Maurice C. Fuerstenau

The kinetics of leaching galena with ferric chloride and ferric nitrate have been examined as a function of ferric concentration, salt concentration, temperature and particle size. Diffusivity of ferric complex ions was also established as a function of ferric chloride concentration and temperature. In the presence of 3 M NaCl, leaching rate is controlled by product layer diffusion when ferric chloride is added as oxidant. With NaCl concentrations less than 3 mole/liter rate decreases with decreased NaCl concentration, and, thus, rate is apparently not controlled by product layer diffusion. It is suggested that rate is controlled by lead chloride solubility at the reaction interface under these conditions. When ferric nitrate is added as oxidant, leaching rate is limited by chemical reaction control. An electrochemical model is presented. Activation energies are 8.1 and 11.3 kcal/mol in the ferric chloride and ferric nitrate systems, respectively.

Jan 1, 1984

By K. L. Paciorek

The aim of the present study was to determine the thermal oxidative behavior of materials used in coal mines, with emphasis on the type and relative concentration of the products, in particular the toxic species formed. To supplement this work and to gain understanding as to the type of products possibly formed and also to assess the limitations and advantages of the various analytical methods used a literature survey of the past investigations performed on the compositions of direct interest to the subject program was conducted. The compositions thus covered were cellulose, polyvinyl chloride, neoprene, urethanes, polyamides, polyesters, polyethylene, epoxy, phenoxy, urea-formaldehyde and melamine formaldehyde resins. The results of this review are compiled in the Appendix. The experimental work consisted of thermal oxidative degradation of 36 materials and 4 composites using a stagnation burner apparatus developed in these laboratories which affords a dynamic system approximating somewhat the conditions encountered in underground coal mines. This technique as employed during this program gave only the relative product concentration at specific periods of the decomposition process, The advantage of this approach is that in this manner screening of materials can be accomplished in conjunction with some assessment of the decomposition rate as influenced by temperature and material composition. Limited static tests were performed using a sealed tube method. The materials studied were grouped according to their compositions. The following were the main groups: (a) polyvinyl chloride-containing materials, (b) neoprene compositions, (c) rigid foams (urethanes, isocyanates), (d) miscellaneous materials (including jute, fiberglass, polyethylene and some articles of unknown composition), (e) coal and fluids (phosphate esters, organic esters, oil-water emulsions), and finally (J) composites. The latter comprised a mixture of a phosphate ester fluid with (a) coal, (b) a representative polyvinyl chloride sample, and (c) a neoprene type composition.

Jan 1, 1972

By R. A. Hatch

The United States depends mainly on foreign imports, principally India, for an adequate supply of sheet mica suitable for its many uses in the electrical and electronics industries. Sheet mica has, in fact, played an indispensable role in developing these industries,4/ and, in turn, the products of these industries (radio, radar, electric motors, and many others) have become indispensable to the military forces. Because or these conditions, sheet mica in its better qualities long has been classified as a strategic and critical material, and from this stems the wide-spread interest in substitute materials of which synthetic mica is one potential type. The United States Departments of the Navy and the Army entered into a cooperative agreement with the Bureau of Mines in 1947 to study ways and means of synthe-sizing and growing mica crystals. This is one of a series of reports5/ that describe the results of this program.

Jan 1, 1956

Approximately half of all the fuel energy used in the United States is now pro-vided by oil and natural gas. A persistent and rapid growth in energy demand during the last 3 decades has been absorbed largely by the liquid and gaseous rather than solid fuels. In 1948 the energy provided by coal was substantially the same as in 1920. Meanwhile, the use of oil and natural gas each had increased fivefold. On a per capita basis, the change is more significant. Coal consumption has dropped from about 6 tons per person to 4-1/2 tons, while oil has increased from 4-1/3 barrels to 14-1/3, and natural gas from 7,500 cubic feet to about 35,000. These facts would have only academic interest if the United States had unlimited supplies of all fuels. However, while the Nation's reserves of coal are adequate to meet our needs for centuries, those of oil and natural gas appear limited. It is obvious, therefore, that the security of our liquid-fuel position would be greatly enhanced if the supply could be based in an increasing degree on solid fuels, such as coal/and oil shale, which make up more than 95 percent of our fuel reserves, instead of natural oil and gas. In addition, this would create new employment and help to stabilize the market for coal, which may be facing comparatively bleak prospects in the near future unless its position with respect to other fuels is improved.

Jan 1, 1950

By E. C. Fitch

This report discusses fire-resistant hydraulic fluid safety from three different directions. First, results of a survey prepared for the Fire Resistant Hydraulics Journal by the staff of the Fluid Power Research Center are analyzed. Second, operational limitations of fire-resistant hydraulic fluids are examined. Finally, laws and standards of various foreign countries are investigated. Three conclusions are derived from a close study of fire-resistant hydraulic fluid safety from these three directions. First, a significant number of experts in the fluid power industry are no in agreement about aspects of fire-resistant hydraulic fluid fire-resistance and toxicity. This indicates a need for more in depth research. Second, the use of fire-resistant hydraulic fluids involves a compromise between the decreased fire hazards and increased toxicity and machine incompatibility problems. Finlly, major foreign governmental agencies have thorough laws and standards concerning fire-resistant hydraulic fluids. These laws and standards may provide a solid framework for further international research into fire-resistant hydraulic fluid safety.

Jan 1, 1979

By David Allen Jones

A depleted county gravel pit was rehabilitated by contracting an artist to convert it into sculpture, rather than using traditional reclamation methods. The sculptor's ideas were generally implemented as designed, but problems arose because of a faulty survey and severe weather. Public reaction was critical. A design symposium was presented by retaining six artists to prepare designs for varied sites. A public forum was offered and video-documented for broadcast. A new art-reclamation project grew out of this project.

Jan 1, 1981

By W. H. Oppelt

The Federal Bureau of Mines investigated combustion of lignite in domes-tic heating equipment to obtain information on equipment performance and to evaluate testing procedures. Three types of domestic heating equipment were tested, ranging from a hand-tilled, magazine-type space heater to a ram-type overfeed stoker. Lignite was readily burned in each of the three units under various test conditions. Burnoff rates determined by adding weighed charges to the magazine were found to be in error because of shrinkage of the lignite when only a portion of the magazine capacity was consumed during a test. More reliable burnoff rates could be determined by carbon-nitrogen balances. A hand-fired magazine-type space heater (Booker heater) was operated without the furnace attachment at efficiencies to 75 pct. One test series was run with minimum supervision under conditions encountered in actual household operation. No mechanical trouble was encountered.

Jan 1, 1960

By W. A. SLOAN, G. L. Oldright, J. D. Sullivan, E. K. PRYOR, A. F. HALLET, R. S. Dean, S. L. BROWN, F. S. Wartman, A. J. Thompson

Lack of sufficient publication funds has resulted in the accumulation of considerable unpublished experimental work on copper metallurgy by the Bureau staff . The present report gives extended abstracts of this work , as well as a discussion of the best direction for future efforts . The experimental work reported in this series of papers was done in cooperation with the University of Arizona , Tucson , Ariz . The investigations covered in the third , fifth , and seventh papers were done under the direction of G. L. Oldright and the remainder under the direction of V. H. Gottschalk .

May 1, 1934

By Arthur E. Bruszak, Marcel Vanpée

In many practical combustion systems ignition may occur through contact with hot burned gases . Such a process plays a vital role in flame stabilization on bluff bodies . It is also of importance in the ignition of firedamp by the hot spent gases of explosives used in mines . Also , in the communication of flames through narrow channels , a problem of practical importance in flameproofing electrical equipment , the propagation of the flame is essentially a reignition process in which hot burned gases are the agent of ignition . In the actual ignition problem a great variety of conditions may be visualized . Ignition may occur where pockets of hot gases are surrounded by cold explosive mixtures or where pockets of cold mixture may be surrounded by hot gases . Alternately , a flowing stream of combustible mixture may be initially in contact with another stream of hot combustion products , or a jet of hot gases may flow into a cold quiescent mixture ; the jet may be laminar or turbulent , continuous or discontinuous . The hot gas may also consist of the oxidant ( air for instance ) and the cold combustible pure fuel . This study by the Bureau of Mines is concerned only with ignition produced by a continuous jet of gas ( hot ) flowing into a practically quiescent cold mix- The investigation of ignition by bursts of hot gases or by turbulent jets is outside the scope of this report , and work performed on this phase of the problem has been published elsewhere

Jan 1, 1963

By Frank G. Schwartz

VARIABLES OF composition and environment affecting storage stability of gasoline-type fuels were studied, utilizing radioactive tracers and other analytical techniques. Changes in gasoline composition brought about by aging were determined and correlated with gum formation. The amounts of reaction of selected gasoline components, measured by radioactive tracers, were determined in a gasoline-type blend and in a mixture of 17 selected pure gasoline components. The data show that sulfur compounds, nitrogen compounds, polycyclics, and olefins enter into gum-forming reactions. Certain sulfur and nitrogen compounds were found to be most reactive in the gum-forming process. Results of this study indicate that the aromatic constituents of gasolines may contribute substantially and directly to gum formation. A mixture of tetralin and indan-type compounds is reactive, and this mixture appears to be the main aromatic portion entering into gum formation. A secondary but significant amount of naphthalenes also appears to have reacted in the gum-forming process. Analyses of the sulfm compounds in a fresh and an aged fuel indicated that elemental sulfur, hydrogen sulfide, thiols, sulfides, and disulfides were depleted during aging, but thiophenes and residual sulfur compounds were not depleted by fuel deterioration.

Jan 1, 1964

By R. A. Hatch

This report summarizes the results of nearly 8 years research on and production of synthetic mica at the Electrotechnical Experiment Station of the Federal Bureau of Mines, Norris, Tenn. This program was undertaken at the request of the United States Department of the Navy and was financed mostly by the Army Signal Corps and the Navy Bureau of Ships through a contract with the Office of Naval Research, The original objectives included fundamental studies of fluor-phlogupite and other fluorine-micas and production of synthetic mica sheets on a pilot-plant scale. The first 3 years of this project were devoted mainly to a search for practical solutions of the many problems involved in designing and constructing a pilot plant for crystallizing fluor-phlogopite mica. The first and most urgent need was a suitable container for the corrosive mica melt. After extensive study, it was concluded that platinum, graphite, high-silica fire clay, and silicon carbide were the most promising refractories for crucibles; but none was perfect. Silicon car¬bide seemed to have the better combination of qualities, combining good corrosion resistance with oxidation resistance.

Jan 1, 1957

By Christopher Mark

This proceedings volume contains papers presented at technology transfer seminars sponsored by the National Institute for Occupational Safety and Health (NIOSH) on New Technology for Ground Control in Retreat Mining. The seminars were conducted at five locations: Uniontown, PA (March 26, 1997), Norton, VA (April 8, 1997), Pikeville, KY (April 10, 1997), Charleston, WV (April 17, 1997), and Evansville, IN (April 22, 1997). The papers presented here describe several new, highly practical technologies developed by the NIOSH Pittsburgh and Spokane Research Centers3 to improve safety during pillar retreat operations. Two central issues are addressed: pillar design and mobile roof supports (MRS's). Proper pillar sizing is essential for safe pillar extraction. The Analysis of Retreat Mining Pillar Stability (ARMPS) program and its large data base of actual mining case histories are presented. LAMODEL, a second computer program, can be used for analysis of multiple-seam and other complex mining situations. Other papers address pillar design to avoid massive pillar collapses and the proper role of coal strength testing. MRS's have greatly improved safety where they are used for pillar line support. We studied the application of MRS's at 20 mines throughout the Eastern United States. Conclusions regarding the most effective section layouts, cut sequences, and support placements are reported. Field and laboratory tests of MRS's are also described.

Jan 1, 1997

By R. K. Koch

The vapor pressures of liquid titanium and liquid platinum were studied under the Bureau of Mines program for the determination of thermochemical data on the transition elements. Beating was done in a 2-kw electron-beam furnace with a water-cooled copper crucible to contain the melt. Temperature was measured with a disappearing-filament brightness pyrometer. The vapor pressure data for liquid titanium in the range 2,008° to 2,379° K are represented by the least-squares derived equation [log p (atm) = 6.268 - 22, T] Two series of determinations were made on liquid platinum. Results of the first series are expressed by the least-squares derived equation [log p (atm) = 8.240 - 30,460T] for the range 2,0860 to 2,4200 K. Results of the second series are expressed by the least-squares derived equation [log p (atm) = 7.795 - 29,580 T] in the range 2,045° to 2,442° K. Third-law evaluations of each series gave mean standard heats of sublimation of 112.4 kcal/mole, 133.3 kcal/mole, and 133.8 kcal/mole for titanium first series on platinum, and second series on platinum, respectively. Second-law heats of sublimation and equations for heats, free energies, and entropies of vaporization were obtained from sigma plots of each data set.

Jan 1, 1969

The original manuscript of section 2 of this series of miners' circulars devoted to accident prevention in bituminous-coal mines was completed in September 1944. At that time roof bolting had been tried with some success in the lead-mining district of south-eastern Missouri, but information on the subject was so fragmentary that it was not included as a method of roof support. References to roof support in bituminous-coal mines, therefore, were confined almost entirely to conventional timbering methods. In 1947 the Bureau instituted a research program and intensive study of the general problem of roof control, which emphasized roof-bolt application. The rapid increase in mechanized mining following the close of World War II provided the impetus for the Bureau's roof-control investigations, because the vertical supports used with conventional timber restricted the maneuverability of mechanical face equipment, and the industry wanted to explore every possible method of eliminating interference with the production cycle to gain full advantage of mechanized mining. Moreover, the accidental dislodgment of vertical supports greatly increased the roof-fall hazard. As roof falls have killed and seriously injured more mine workmen every year than any other cause or classification of injury since records have been kept, the Bureau assumed this investigative leadership with the prime objective of substantially reducing the annual toll from falls of roof, including falls of rib and face.

Jan 1, 1958

By W. F. Watts

This report describes a statistical analysis of 41,502 respirable quartz dust samples collected from 1974 through 1981 in metal and nonmetal mines and mills. The goal of this Bureau of Mines study was to identify commodities and occupations associated with high quartz dust exposure so that future enforcement and research activity can be focused on the high-exposure areas. For this analysis, the Bureau used its computerized Mine Inspection Data Analysis System (MIDAS), which contains data on nearly 350,000 air samples, including data for 61 contaminants in 45 commodities. The samples analyzed were collected by inspectors of the Mine Safety and Health Administration (MS HA). The data were entered into the MIDAS computer and coded according to commodity, occupation, location, and other categorical information. Occupations an. commodities with high quartz dust exposure were identified by grouping the data by code categories. Workers at sandstone, clay and shale, and miscellaneous nonmetallic mineral mills had the highest quartz dust exposures. Within these mills, occupations with high exposures were baggers, general laborers, and persons involved in crushing, grinding, and sizing operations. Dust concentrations in these mills were not necessarily the highest, but because the dust contained a high percentage of quartz, the health risk from dust exposure was the greatest.

Jan 1, 1984