Search Documents

By Jesse J. Brown

Over 60 simple; were prepared and forwarded to Dr, S. Z. Toma, TPO, PMSRC as a result of this project. Included among these samples were various low temperature forms of silica. Samples of quartz, cristobalite, and tridymite with iron, manganese, and titanium impurities present were prepared. In addition, a long series of samples both wet ground and dry ground for times from 1/2 to 8 hours were prepared. Numerous miscellaneous samples were submitted which included kaolinite, calcite, muscovite, illite, montmorillonite, Ba3(P04)2, and YPO4 among others, in response to special requests from the TPO. The silica rich portion of selected binary (CA 203-Si02, In 203-Si02, Li20-Si02) Na20-Si02, PbO-Si02, SnO2-Si02, Sn02-Si02 BaGa204-SiO2 and SrGa204-Si02) and ternary systems (Na20-Ga203-Si02 and Li20-Ga203-Si02) was investigated to determine the effects of solid solubility on the stabilization of the high temperature forms of tridymite. In addition to the determination of the extent of these crystalline solubilities, observations were made. on the mechanism of the transformation of silicic acid to tridymite and the rate of the reaction in the presence of foreign ions,

Jan 1, 1973

By D. J. Parker

Before the various States began to enact workman's compensation laws accidents were considered inherent in many industries, and little or no effort was made to prevent or reduce them. The hazard was accepted by the employee with the job, and the avoidance of accidents by mental alertness or physical agility was largely his responsibility. After the employee had given evidence of enough skill inn performing his allotted task efficiently the responsibility of the employer apparently ceased with respect to the personal safety of the employee. However, following the enactment of workmen's compensation laws, at least two facts that had not before been fully appreciated soon became apparent: (1) The majority of accidents can be prevented if the management firmly determines to prevent them; (2) frog a monetary point of view alone accidents are decidedly expensive, both to employer and to employee. It is now evident that savings effected by conscientious safety effort add substantially to net profits of operation.

Jan 1, 1934

By Jr. Hazen

Two statistical techniques, the mean-square-successive-difference test and correlation, are used to investigate the problem of assigning an area of influence to an assay. Data from five hydrothermal deposits, Climax molybdenum, Cebolla Creek titaniferous iron, San Manuel copper, Piedra Hueca copper, and Butte copper, are studied. Two groupings of the assays are used for the mean-square-successive-difference tests. One group involves an increasing sample volume by reaveraging assays to represent a longer sample intervals, the other by regrouping assays to represent longer sample intervals without a change in sample volume.

Jan 1, 1967

By Richard J. Mainiero, James H. Rowland III, Marcia L. Harris

This paper reviews the potential hazards posed by the toxic fumes produced by detonating explosives in surface mining and construction operations. Blasting operations produce both toxic and nontoxic gaseous products; the toxic being mainly carbon monoxide (CO) and the oxides of nitrogen (NOx). The quantity of toxic gases produced by an explosive is affected by formulation, confinement, age of the explosive, and contamination of the explosive with water or drill cuttings, among others. Techniques to protect workers and the public from the potential hazards of explosive-related toxic fumes are discussed. These include: • Minimizing the quantity of toxic fumes produced. • Determining where the fumes may go so workers and neighbors can be moved out of harm’s way. • Preventing the fumes from moving towards workers and neighbors. • Monitoring the air near workers and neighbors so they can be relocated if fumes appear. • Ventilating structures or confined spaces until CO falls below a hazardous concentration.

By G. B. Clark

One portion of this project was to test a blast shield and to design some features for a novel tunneling method termed the Automated Drill and Blast System (ADBS). The ADBS tunneling concept was developed for the design of an excavation system of greater efficiency than conventional drill, blast, and muck (DBM) systems by minimizing the down time and approaching the non-cyclic efficiency of continuous tunneling by means of small charge blasting. Small charge blasting uses simultaneously detonated, small light charges (less than 200 grams per hole) in four to eight shallow (24 to 36 in. deep) holes usually in a line. Limitation of the total explosive per blast reduced air blast overpressure, fly rock velocity, vibration, and noise. Thus, shielded equipment can remain at the face and a tunnel shield permits support personnel to work outby the shield at all times. The ADBS equipment will be composed of five components: (1) a chassis, upon which is mounted automated mucking equipment, and a frame which carries (2) the hydraulic drill(s), (3) load/blast system(s), and (4) control cab(s). The blast shield may have its own mounting. Ventilation, horizontal, and vertical alignment controls are incorporated in the system. The blast sheild, which protects personnel outby the advance equipment from air blast overpressure, fly rock, and gases, was tested with full scale small charge blasting. A blast shield was designed, fabricated, and tested under conditions anticipated for a working model. The shield was designed to expand to fit the tunnel shape, to seal itself to the tunnel periphery, and to contain air blast, fly rock, and gaseous explosion products. In addition, the shield, which was lined on the inby side with rubber belting, reduced the blast noise level outby the shield to 113 dBA or less, which is very near permissible levels. The test results show conclusively that the shield concept is viable. Based partially on the shield tests, a blast resistant control cab was designed to be located on the equipment chassis inby the blast shield to protect operators during blasting, and to contain all the controls necessary for system operation and safety. The economics of tunnel driving using the ADBS were compared with those of DBM. Four rock types, which determine advance rate, and four cost categories were examined. The results of this analysis are as follows: 1. ADBS advance rate is faster because equipment remains at the face and operation procedes semi-continuously. 2. ADBS bit and explosive cost (which accounts for 4%o of the total advance cost) is higher than for DBM. 3. ADBS equipment cost, on a per foot basis, is lower than for DBM. 4. Due to a reduced labor force, ADBS labor cost is lower than for DBM. 5. Because of the overbreak reduction due to controlled blasting, ADBS tunnel support cost is lower than for DBM. 6. On a per foot basis, total ADBS advance cost is from 17% to 20% lower than for DBM, depending on tunnel diameter and rock type. The small charge method greatly reduces ground vibration, increases personnel safety by limiting excessive fracture, and decreases tunnel support requirements by reducing overbreak. The overall analysis, tests, and results to date show that the Automated Drill and Blast System may be developed into a viable tunnel excavation method. The method also may be adapted to use in the mining of ore. For some types of mining operations, the cyclic nature of conventional drill and blast methods may not be a disadvantage, either where the drilling and mucking may proceed simultaneously or where the operations are carried out in adjacent working faces. The proposed method would find application where continuous methods of excavation are desirable.

Jan 1, 1979

By Khamis Y. Haramy

This Bureau of Mines paper describes the use of the borehole shear tester (BST) In mines. Assembly and procedure sections explain how the equipment is assembled and used properly. Schematics of the BST, limitations, test hole specifications, data recording and calculations are all explained briefly, and an example of the data collecting and calculations is given to assist understanding.

Jan 1, 1981

By David A. Lipton

U.S. Bureau of Mines personnel examined mines, prospects, and mineralized areas to determine the mineral resources and potential of the Moses and Dennison Peak RARE II areas in Tulare County, California. These areas, along the west slope of the Sierra Nevada, are underlain by grarnitic rocks of the Sierra Nevada batholith and contain numerous metasedimentary roof pendants. Silver, copper, and zinc occur in contact-metasomatic deposits within the metasedimentary rocks. In the Moses area, the Powell Mine (fig. 1) contains an estimated 90,000 tons (82,000 t) of subeconomic silver, zinc, and copper resources. The King Solomon Prospect has 3,000 tons (2,700 t) of silicified phyllite containing zinc. On the Helen-Joyce Prospect, 44,000 tons (40,000 t) of gossan occur above a poorly exposed silver-zinc rich zone. Potential exists for additional mineral resources and occurrences at each of these properties.

Jan 1, 1983

By Edward A. Barrett

The ability to recognize visual cues commonly associated with roof and rib hazards is fundamental to the prevention of groundfall accidents. The perceptual skills that miners possess to visually search and assess hazardous ground conditions differ considerably. This U.S. Bureau of Mines report summarizes recent investigations on the use of stereoscopic (3-D) slides as a training aid for improving the ability of miners to recognize the various geologic and mining-induced irregularities that cause ground-falls. The feasibility of using 3-D slides for training and their effectiveness for representing roof and rib hazard conditions are discussed. Information is presented on equipment and procedures for creating a 3-D slide program that can be updated by mine trainers. Recommendations are made on selection of 3-D equipment and on the use of 3-D slides for training miners to recognize roof and rib hazards.

Jan 1, 1988

By M. L. Skow

Large tonnages of the manganese ores found in Aroostook County, Maine, are refractory to conventional mineral-dressing techniques and to the common chemical- extraction procedures. The Maple Mountain-Hovey Mountain ores are typical of this type. Because the most promising method of recovering the manganese from these ores has been a chloridizing roast in which the ground ore is in contact with gaseous hydrogen chloride, preliminary batch tests were made with a fluidized bed. On the basis of these tests, it was concluded that fluidization, with careful control of operating conditions, could be employed for this cloridization and warrants further study. Selective volatilization of the iron at 600° C. was unsuccessful. An operating temperature of approximately 950° C. was necessary for a practicable rate of volatilization of manganese chloride. Hydrogen chloride contents of 10 to 100 percent of the fluidized gas gave essentially equivalent manganese recoveries with an 80- minute retention time, For shorter periods reaction was more complete with the higher hydrogen chloride concentrations. At the 80-minute retention period the lower hydrogen chloride concentrations volatilized somewhat less iron and also improved the physical operation of the process. Fluidization gave results superior to comparable tests on chloridization in a fixed bed.

Jan 1, 1956

By A. G. Loomis

METHODS for measuring relative permeability as a valid function of saturation were compared by the. Bureau of Mines, using core samples from representative oil-productive California formations, from the Bartlesville sand in Oklahoma, and from synthetic samples. Measurements for gas-oil systems were made by steady-state dynamic, unsteady-state displacement and two stationary-phase methods. Measurements for water-oil systems were made by the unsteady-state displacement method. As the ratio rather than individual relative permeabilities is measured by the last method, three methods for calculating individual relative permeabilites from their measured ratio were compared for gas-oil systems and two methods for water-oil systems. Errors arising from capillary discontinuities, such as the end effect and stabilized-zone flow, are discussed and evaluated; possible errors rocs arising from turbulant flow are also examined. The inapplicability of non-steady-state methods for water-oil systems that are not definitely oil-wet is discussed in detail. Measurements of relative permeability to both gas and oil can be made quickly and accurately by the steady-state dynamic method when rates of flow of the two phases are sufficient to minimize the capillary discontinuity at the outflow end of the sample. At such rates relative permeability-saturation measurements are essentially independent of the rate of flow. The steady-state method wits modified by a dispersion section at the inflow end of the sample acid designated tie dispersed-feed method.

Jan 1, 1962

By Phillip N. Yasnowsky

The thrust of this Bureau of Mines report is to relate the size of automobiles to the price of gasoline, and the use of minerals in automobile manufacture to the size of automobiles. Only one of the many plausible scenarios of public reaction to higher gasoline prices, a switch to economy size automobiles, is developed. No account is taken of other potential impacts such as improvements in public transportation or increased occupancy per vehicle. Furthermore, a gasoline price increase is the only incentive to the greater utilization of economy cars that is considered. A gasoline price increase to $0.60 per gallon would reduce the amount of minerals required to produce the automobiles sold in the United States by an estimated 15 percent. Gasoline prices of $0.80 and $1 per gallon would cause declines in mineral requirements for U.S. automobile sales estimated at 26 percent and 35 percent, respectively.

Jan 1, 1974

By F. J. Perzak

The Bureau of Mines conducted a study to develop a standard fire test for 5-gal containers used for storing combustible fluids in underground coal mines. A standard test method was developed which evaluates the performance of the container in a 4-min tray fire. Bureau investigators used the standard test method to evaluate several types of closed 5-gal plastic and metal cans in outdoor tests. Each can tested contained 1 gal of nonfire-resistant (NFR) hydraulic oil. A container failed the test if it lost its contents in any of seven trials. Contents spilled either as a result of thermal rupture or melting. Fewer than 10 pct of the metal containers failed this criterion, but all the plastic containers failed. The metal container failures were usual-ly due to tipping over during pressure relief, which spilled the NFR oil. Replacing the NFR oil in the container with kerosene resulted in failure of more than 30 pct of the metal containers. The standard tests and preliminary tests showed that plastic containers are not equivalent to metal containers in their ability to contain combustibles such as lubricants and greases in a fire. For solvents and lubricants more volatile than NFR hydraulic oil, approved metal safety containers are recommended.

Jan 1, 1985

By J. H. Daniel

This report, summarizing the results of two studies sponsored by the Bureau of Mines, presents information on the types of mobile machines used in surface coal mines in the United States, and the amount of noise to which miners are exposed. Data consist of a calculated value of the probability of noise overexposure caused by specific equipment. These data are extrapolated to estimate the number of overexposed operators. Bulldozers were identified as the major contributors to noise overexposure, and the report presents results of a Bureau-funded program on the feasibility of providing retrofit noise control on bulldozers.

Jan 1, 1980

By E. Wittenau

This paper describing the concentrator practice of the Copper Queen Branch of the Phelps Dodge Corporation at Bisbee, Ariz., is one of a series of papers on milling methods and costs being prepared by the United States Bureau of Mines. The Copper Queen Concentrator treats 4,000 tons of copper ore daily by preferential flotation, whereby the copper sulphides are floated and considerable iron pyrite is depressed. During 1929 the heads to the concentrator averaged 2.15 per pent of copper, the recovery was 91.32 per cent of the total copper, and the concentrates produced contained 12.92 per cent of copper.

Jan 1, 1931

By John F. Papp

Based on a review of historical domestic and international chromium metal production capacity, production, consumption, trade, and trade literature, world annual chromium metal production capacity in 1995 was estimated to have been 38,300 metric tons, a drop from 43,500 tons in 1994. World chromium metal production and consumption were estimated, on average from 1984 through 1992, to have been 21,000 tons per year. U.S. consumption was estimated, on average over the same time period, to have been 6,200 tons per year. The major world chromium metal producers between 1984 and 1995 were China, France, Germany, Japan, Russia, United Kingdom, and United States. From 1984 through 1992, world trade averaged 8,400 tons per year. Germany and the United States accounted for over 75 percent of imports on average during the same time period. U.S. chromium metal import value rose from under $1 per kg before 1964 to over $6 per kg in 1993. Over the same time period, prices rose from about $4 per kg to about $10 per kg. Chemical specifications have become more stringent. Detailed chromium metal trade, prices, value, chromium metal chemical specification, and production capacity by country are reported. A shift in trade patterns was anticipated as Japan exits production and displaces Germany as the second largest importer and as Russia increases its role in world trade.

Jan 1, 1995

By Alan H. Goode

Glass wool meeting requirements for commercial use was made from glassy fractions of urban solid wastes by the Bureau of Mines. This research was a part of the Bureau's program to develop building products and other usable materials from reclaimed urban waste materials. Mixes of molten glass were fiberized into glass wool during laboratory studies by impingement of a jet of compressed air on a stream of the molten glass. The principal test variable studied was composition of the melt; this was varied by adding dolomite and alumina to obtain molten glass with the handling characteristics required for producing final wool products of the desired composition and physical characteristics. When no charge is made for the waste glass and approximately $75 per ton can be obtained for the wool product, an interest rate of return on investment after taxes of about 12 percent can be obtained. If a charge of $5 per ton is required for the waste glass, a selling price of about $78 per ton would be necessary to obtain a l2-percent-interest rate of return on investment after taxes.

Jan 1, 1972

By H. V. Makar

Laboratory tests were performed to obtain a quantitative description of the effectiveness of sodium sulfate (Na2SO4) for removing copper from molten iron and to determine the effectiveness of Na2SO4 on actual auto scrap. The tests were conducted on induction melted heats of iron averaging 0.58 and 1.50 percent initial copper and on cupola-melted auto scrap containing 0.45 percent initial copper. The Na2SO4 was added in powder form in amounts ranging from 2.9 to 43.8 percent of the weight of iron being treated. The data showed that copper removal for the various Na2SO4 treatments followed a similar trend, regardless of the iron composition that was tested. The equation Y = 1 - e-3.23x approximately reflects the relationship between copper removal and amount of Na2SO4 added, where Y is the fraction of copper removed and x is the ratio of the weight of Na2SO4 added to the weight of metal treated. Copper removals ranged from 3.3 to 74.5 percent and reductions down to less than 0.10 percent final copper were achieved in the auto scrap. Copper removals were generally accompanied by sulfur removal, and initial sulfur contents ranging from 0.10 to 0.20 percent were reduced to as low as 0.02 percent. High temperatures and long slag reaction times tended to induce copper and sulfur reversion from the slag, but, generally, the Na2SO4 treat¬ments were effective up to approximately 2,820° F with reaction times not exceeding 7 minutes.

Jan 1, 1968

By J. P. Powell

Since the beginning of waterflooding in the Midcontinent area, the Bureau of Mines has published many reports3-6/ describing in detail the results obtained on individual waterflooding projects in the area. These are intended as guides for operators in the selection of well-spacing, water-treating, and other techniques, as well as an indication of the results being obtained in waterflooding in various areas, fields, and horizons. In addition, Bureau personnel has arranged a tour of selected waterflooding projects each year for the past several years so that actual operating conditions may be observed and an additional opportunity provided for exchanging information. Each of these tours has been supplemented by a published

Jan 1, 1959

By James Westfield

A brief résumé follows of recent activities of the Division of Coal-Mine Inspection that have had a favorable effect on health, safety, and the reduction of injuries at coal mines: 1. The Federal Mine Safety Code for Bituminous Coal and Lignite Mines of the United States was issued originally by the Director of the Bureau of Mines on July 24, 1946, after consulting with management and labor representatives of the coal-mining industry. The code has been used by Federal coal-mine inspectors while inspecting bituminous-coal and lignite mines as a basis for determining the existence of unhealthful and unsafe conditions and practices in these mines. A revised code was issued by the Secretary of the Interior on October 8, 1953, after further consultations with representatives of management and mine workers and was incorporated by reference in the 1952 and subsequent bituminous-coal wage agreements. The agreement of May 29, 1946, between the Secretary of the Interior, acting as Coal Mines Administrator under authority of Executive Order 9728, and the United Mine Workers of America, covering bituminous-coal and lignite mines in Government possession, charged Federal coal-mine inspectors with the responsibility of making periodic investigations of the mines and reporting to the Coal Mines Administrator any violations of the Federal Mine Safety Code. Federal coal-mine inspectors also had temporary authority to close mines found to be imminently dangerous, but such authority (under Executive Order 9728) was removed on June 30, 1947, when Government control of the mines was terminated.

Jan 1, 1958

By Michael Rieber

Among the principal gathering/distribution systems for coal is over-the-road trucking. Where alternative trunk line modes such as barge or rail links are weak or nonexistent, trucks may, particularly for relatively short line hauls, act as substitutes. Their major application, however, appears to be in connection with smaller mines or coal users particularly where terrain problems are significant. Truck use has increased as rail lines have been abandoned or suffered neglect. For example, in 1956 about 38 percent of the coal transported in eastern Kentucky and about 8 percent of the coal moved in western Kentucky went by truck. By 1975, the percentages were almost 77 percent and 26 percent, respectively [4,U-11]. While rail route .limitations and deterioration played a part in the change, increased emphasis on road building, particularly during the 1950's and 1960's, and improved truck load capacity and efficiency were also important.

Jan 1, 1977