Search Documents

This Bureau of Hines report on underground mine communications addresses methods and equipment to meet the communication requirements of working sections and places of coal and metal-nonmetal mines. A review of the status of trapped miner detection is also presented.

Jan 1, 1977

By Mark P. Zaitsoff

The project involved design, construction, and testing of hydraulic models of culverts, decant and open channel spillways which are typical drainage structures used for protecting mine waste embankments. MSHA (The Mine Safety and Health Administration, U. S. Department of Labor) made a motion picture of the tests. Tests results and products in the forms of graphs, tables and films, demonstrate the principles and factors which govern the function and performance of the three types of drainage structures.

Jan 1, 1981

By Douglas F. Scott

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied an 11,980-acre part of the 33,300-acre High Rock Canyon Wilderness Study Area, CA-020-913B, in order to evaluate its identified mineral resources. No mineral resources were identified during this study, and no significant amounts of gold, silver, mercury, gem-grade opal, or placer gold are present. The study area is located in Washoe County, NV, about 53 miles southeast of Cedarville, CA. No mining districts or mineral production are known, and no oil and gas leases are in the area. No current claims are in the area; however, six placer claims were located in 1911 in High Rock Canyon near its confluence with Mahogany Creek.

Jan 1, 1987

By William C. Cooley

This report includes a review of all relevant data on underground hydraulic coal mining technology collected during Phases I and II of the contract. Data collection and analysis procedures are discussed. Information is included on past and existing underground hydraulic coal nines in the USSR (27 mines), Poland (1 mina), Germany (1 mine), Japan (1 mine), Canada (1 mine), China (1 nine), as well as underground tests conducted in the United Kingdom (2 mines), and in the United States (5 mines). Data is also included on Czechoslovakia and New Zealand. In all operational hydraulic mines, coal is transported underground in flumes. In most cases, bituminous coal is broken by monitors with nozzle diameters larger than 16 mm (0.63 in.) and jet pressures of 50 to 125 atm (710 to 1780 psi). Technical design and performance data are included on all key types of equipment and components which have been developed for, used in, or which could be potentially be used in hydraulic coal mining systems. Data sheets are presented on 180 types of equipment, divided into 24 major categories. Where available, sketches, drawings, photographs, and price estimates are included. Data are included on pitching coal seams in the United States which potentially can be mined by hydraulic methods. Preliminary conclusions are presented, subject to revision as a result of economic feasibility studies to be completed during Phase III. An outline is presented of the final report, which will include economic studies and recommendations for research and development.

Jan 1, 1975

This report describes the work performed by Mine Research Company in developing a prototype mobile roof shield during 1971-1972 for the U. S. Bureau of Mines, along with background information leading to the design decisions adopted for the project. In addition, the report evaluates the choice of design and analysis and the results of the project in terms of future possibilities of mobile roof support systems. The report begins with the discussion of the problems of designing, building, and using mechanical and hydraulic roof support in coal mines. It then gives a historical summary of past work with discussions of the design choices made for previous roof support systems.

Jan 1, 1973

By F. G. Schwartz

This circular presents the results of a survey of research on jet fuel thermal stability jointly sponsored by the National Petroleum Refiners Association (NPRA), Tulsa, Okla., and the Bureau of Mines. The development of supersonic planes has led to many problems that did not exist in the operation of subsonic aircraft. One of the most important of these is rapid deterioration of the fuel at the high temperatures to which it is subjected. At higher speeds, aerodynamic heating of the airframe imposes severe thermal problems, and conventional techniques of rejecting the heat to the atmosphere become impractical. The fuel is the only material present in sufficient bulk to be used as a heat sink. Thus, the fuel is subjected to aerodynamic heating and also is used to dissipate heat from lubricating oil, hydraulic fluid, electronic equipment, wheel wells, and cabin air. Consequently, the fuels may have to withstand both moderate temperatures for sustained periods in the fuel tanks and higher temperatures for brief periods during transfer from the tanks to the combustion chamber. Because of high temperatures, insoluble residue or gum may form in the fuel and contribute to heat exchanger fouling and to clogging of the fuel manifolds, nozzles, control systems, and other components of the fuel system.

Jan 1, 1962

By E. D. Calvert

Molybdenum has been successfully cast into static and rotating molds in conventional equipment used for casting titanium and zirconium. Melting was accomplished by using an arc potential of 36 to 40 volts with a current of 10,000 amperes. Pouring efficiency, after a skull had been formed in the crucible, averaged 70 percent. Techniques are described by which four successful castings were made. Tensile properties on specimens cut from one centrifugally cast tube averaged: Tensile strength, 39,800 p.s.i.; yield strength (0.1 pct. offset), 35,300 p.s.i.; elongation, nil; reduction in area, nil; impact strength, 2 ft.-lb.; hardness DPH (diamond pyramid hardness) 180. Mold reaction was not evident in shapes cast in machined graphite. This was not true, however, for rammed graphitic-base molds.

Jan 1, 1960

By J. B. Gayle

Commercial flotation plants operate on a continuous basis that is not simulated closely by the batch testing methods widely used in Bureau of Mines laboratory studies of flotation, Batch methods indicate whether a particular separation is possible but provide little or no information about the rates at which such separations can be effected in continuous operation, Therefore, laboratory equipment suitable for testing on a continuous basis was assembled for an investigation of a number of the operating variables that influence the flotation of coal. The results of these tests lead to the following conclusions: 1. Flotation recoveries were markedly influenced by variations in the percent solids in the feed, However, the relation between these variables is complex and depends on the particular coal and operating conditions used. Flotation rates generally increased with increased cell concentrations.

Jan 1, 1962

By T. D. Hackett

Multislice mining methods were analyzed by the U.S. Bureau of Mines to determine their application to western United States thick coal seams; ground control, geology, and costs were considered. Multislice mining is used in widely varying seam conditions worldwide, including flat seams too thick to mine in a single pass, pitching thick seams, and seams containing a rock parting. Longwall multislice methods predominate, but room-and-pillar variants also exist. The initial use of the method in western seams is planned at a deep Colorado mine where a rock parting will be used to separate two slices mined by longwall. Ground control and spontaneous combustion are major hazards associated with multislice mining. A well-consolidated upper slice gob can reduce ground control problems and provide a seal against spontaneous combustion. Geologic analysis indicates that the consolidation of the gob depends on the composition of the upper slice roof, the presence of water, and sufficient overburden pressure. A geologically competent intermediate rock parting can also reduce ground control problems and seal against spontaneous combustion. To compete in western coal markets, the cost of multislice mining must be within the range of normal longwall costs. Analysis indicates that multislice operating costs should be within this range, and that multislice mining costs decrease as panel width increases. Relatively wide (600 to 800 ft) panels also provide increased coal recovery.

Jan 1, 1990

By Robert W. Decker

This report presents a survey of published novel coal cutting (mining) concepts and a brief discussion of each one. A preliminary evaluation follows which identifies promising concepts, emphasizing reduced dust generation and economic production potentials. The promising concepts are then studied more deeply and evaluated in more detail with recommendations given for further development action. The concepts recommended for further work include: Roan and Pillar Mining: Deep Cutting Continuous Miner Linear Cutting Rotary Head Miner Longwall Mining: Oscillating Continuous Water Jet Miner Deep Cutting Shearer

Jan 1, 1981

By R. O. Dannenberg

The Bureau of Mines conducted laboratory investigations with the objective of developing an alternative process for recovering cobalt and copper from complex sulfide concentrates. Processes currently used depend largely upon precipitation techniques to remove impurities and recover cobalt from sulfate liquors prepared by oxidative pressure leaching of the sulfide concentrates. The Bureau conducted bench-scale research on a process for treating cobaltite concentrates, comprising (1) oxidative pressure leaching, (2) jarosite precipitation followed by H202 oxidation and pH control to remove iron and arsenic, (3) copper solvent extraction with a mixed hydroxyoxime-amine extractant, (4) copper electrowinning from recirculating acidic strip liquor, (5) selective cobalt extraction from copper solvent extraction raffinate with a phosphinic acid extractant, and (6) electrowinning of cobalt from a recirculating weak acid strip liquor. Overall cobalt and copper recoveries were 91.7 and 84.1 pct, respectively. Electrowon products assayed 99.8 pct Co and 99.89 pct Cu.

Jan 1, 1987

By D. A. Reynolds

THIS PAPER gives results of an investigation of the composition and carbonizing properties of coals from the Beckley bed, Caretta No. 5 mine, Susanna, McDowell County, and Glen Rogers No. 2 mine, Glen Rogers, Wyoming County, W. Va. The investigation included BM-AGA carbonization tests at. 800° and 900° C. and various chemical and physical tests designed to evaluate agglutinating, plastic, and expanding properties of coal. Both coals were of low-volatile bituminous rank, and each was blended with 70 and 80 percent high-volatile A coal from the Pittsburgh bed, Warden mine, Allegheny County, Pa. The Beckley bed was 39 to 58 inches thick at three points in the Caretta No. 5 mine, and the coal was 39 to 49 inches thick. The carbonizing sample contained 83.0 percent fixed carbon on the dry, mineral-matter-free basis. It contained 3.1 percent moisture, 15.8 percent volatile matter, 72.4 percent fixed carbon, 0.7 percent sulfur, and 8.7 percent ash, as carbonized. The ash softened at 2,680° F. The free-swelling index was 7;i, and the agglutinating value was 7.7. This sample fused weakly in the Gieseler plastometer; its blends with 70 and 80 percent Pittsburgh coal attained maximum fluidities of 830 and 600 dial divisions per minute, respectively. The single coal yielded 83.0 percent coke at 900° C. Yields of other carbonization products per ton of coal at 900° C. were: Gas, 9,950 cubic feet; tar, 3.5 gallons; light oil, 1.36 gallons; and ammonium sulfate, 16.3 pounds. Blending with Pittsburgh coal lowered the yield of coke and raised the yields of other products significantly. Caretta coal yielded strong, blocky coke at 900° C., 89 percent of which was plus-2-inch size. Strength indexes of 900° C. coke from 30:70 blends of Caretta No. 5 and Pittsburgh and of Pocahontas No. 3 and Pittsburgh coals were, respectively: 2-inch shatter, 68 and 53; 1%-inch shatter, 90 and 85; 1-inch tumbler, 50 and 53; and %-inch tumbler, 62 and 65. The specific gravity of the 900° C. gas from Caretta No. 5 coal was 0.272, and the heating values were 491 B. t. u. per cubic foot and 2,440 B. t. u. per pound of coal. The blends yielded much richer gas. Yields of tar acids and bases (0.09 and 0.04 gallon per ton, respectively) were within the normal ranges for low-volatile coals. Caretta No. 5 coal expanded 7.5 percent in the sole-heated oven at a charge density of 55.5 pounds per cubic foot. The blends containing 70 and 80 percent Pittsburgh coal contracted 4.8 and 7.5 percent, respectively.

Jan 1, 1953

By A. R. T. Denues, A. P. Rowles

"INTRODUCTION Summarized data developed by J. E. Crawshaw and E.J. Murphy, 4/of the Explosives Division of the Bureau of Mines, suggesting marked variations in oxygen condition in three permissible explosives, have been reported 5/. Such variation is of interest in other work, it having been shown, for example, that the oxygen condition may have marked effect upon the products 3/ and the propulsive strength 7/ of explosives. It seemed that a more detailed presentation and more usual statistical analysis of these data might be of considerable general interest and not complemented in the literature.This report presents both the original data developed by Crawshaw and Murphy and the results of a simplified but seemingly acceptable statistical analysis of these data. The logical ground for this analysis might seem somewhat questionable because of the lack of systematic information concerning the extent of errors in the analytical procedure but the data show that there are several cogent and seemingly unequivocal indications of real heterogeneity in the explosives."

Jun 1, 1942

By Marvin L. Whisman

This report describes the preparation of tritium-labeled organic compounds to be used by the Federal Bureau of Mines in studying the role of certain gasoline constituents in gum-forming mechanisms. The gasoline constituents that have been investigated boil within a range of approximately 90 to 230° C. and can be classified as paraffins. naphthenes, olefins, diolefins, monocyclic aromatics, polycyclic aromatics, and organic sulfur, nitrogen,: and oxygen compounds. The technique of Wilzbach has been applied to more than 50 samples. Purification techniques have been developed that accomplish rapid and effective purification as well as removal of labile tritium in a one-step operation. Data are presented to show the rate of exchange between tritium and hydrogen that can be expected for a variety of compounds common to a full-boiling-range gasoline. These values should be useful to other investigators using tracer programs involving tritium labeled compounds.

Jan 1, 1961

By Michael G. Zabetakis

Limits of flammability of normal propyl nitrate (NPN) vapor were investigated at ambient and elevated temperatures. Minimum spontaneous ignition and decomposition temperatures were determined with laboratory apparatus over the pressure range from 0 to 4,000 p.s.i.g. Flame speeds and the detonation susceptibility of NPN vapor were measured at elevated temperatures. Stable detonation was obtained with liquid NPN at elevated temperatures, and the detonation velocity was determined to be between 4,700 and 5,100 m./sec.

Jan 1, 1962

By Chris Nelson

Two pieces of European Union (EU) legislation together establish requirements for protection against risks from vibration at work. The vibration directive1 specifies duties of employers to protect workers from risks from exposure to vibration; the machinery directive2, specifies duties of manufacturers and suppliers regarding the safety of machinery marketed in the EU. This paper discusses both directives and the standardisation programmes that support them. It also addresses the implementation of these requirements in Great Britain. Employers’ duties: the vibration directive This directive requires employers to assess and control risks to health and safety arising from hand-arm vibration (HAV) and whole-body vibration (WBV). Member States were required to implement the directive in national legislation by 6 July 2005. Employers are required to eliminate vibration risk at source, or reduced to a minimum. The duties include: assessing risk and exposure; planning and implementing the necessary risk control measures; providing and maintaining suitable work equipment; providing workers with information and training on risks and their control; and monitoring and reviewing the effectiveness of the risk control programme. Daily exposure exceeding a specified action value triggers a requirement for a programme of technical and organisational measures to minimise vibration exposures and the resulting risk, and the provision of health surveillance. Exposures above a specified limit value are prohibited. When conducting their risk assessments, employers are required to “assess and, if necessary, measure” the vibration exposure of workers, for comparison with the action and limit values. Vibration measurement in the workplace is not expected in all cases and the use of vibration information from equipment manufacturers is specifically mentioned. This provides a link with the machinery directive (see below). Manufacturers’ and suppliers’ duties: The machinery directive The machinery directive, first introduced in 1989, is intended to remove barriers to trade. It puts duties on manufacturers and suppliers who place machinery on the European market to design their products to eliminate or reduce risks to health and safety and to warn the user of any residual risks, providing information required for safe use (for example, operator training, maintenance and selection of consumables). There are specific requirements for minimising risk from vibration in the design and construction of the machine and, in the case of hand-held, hand-

Jan 6, 2006

By Timothy Y. Yen

This Bureau of Mines report evaluates audio dosimeters, 3 sample units from each of 10 currently marketed brands. Each dosimeter was treated as a "black box" with the acoustic stimulus as the input and the accumulated dosage as the output. The dosimeter microphones were exposed to a sound field gener¬ated in an anechoic chamber. Characteristics evaluated include frequency response (100 to 8,000 Hz), level-time trade-off rate (88 to 117 db), status of calibration, crest-handling capability, and power consumption rate. Experi¬mental errors revealed by replication of the tests were found to be generally much smaller than variations in performance among the samples of any brand, and possibilities of further reducing the magnitude of these errors are discussed.

Jan 1, 1977

This report is the 21st in a series summarizing research and technologic work on coal and related investigations by the Federal Bureau of Mines - the Chard of the series published on a calendar-year basis 2/ Subject publica¬tions of the Bureau during 1956 are cited, and pertinent Bureau work is described briefly. The most effective method of conserving our important coal reserves is through improved technology of production and utilization. Associated problems form the program of the Bureau.3 4 5 6/ Potential production is depend¬ent on a knowledge of the quantity and quality of the reserves, and the Bureau continues to contribute information on this subject. Many problems are being studied that relate to improvements in current production, including mining methods and health and safety measures. Preparation of mined coal is necessary for its most efficient utilization. Preparation by conventional methods is being studied, as well as the development or new methods. Fundamental studies on the structure and properties of coal are necessary to insure full advantage of the special qualities of different coals. Controlling factors in the efficient use of coal in combustion, carbonization, gasification, and direct and indirect hydrogenation of coal are being studied continuously, and new processes are being investigated. The many advances in all these fields are discussed.

Jan 1, 1959

By William G. Pariseau

The research reported here concerns a four year study of the rock mechanics aspects of two underground hardrock mine study stopes. The first study was conducted at Anaconda Minerals Company's Carr Fork Mine near Tooele, Utah. The second study was conducted at the Homestake Mining Company's Homestake Mine In Lead, South Dakota. Both case studies were cooperative efforts of mining company personnel, the Spokane Research Center of the Bureau of Mines and the Department of Mining Engineering, University of Utah. Large diameter (6 1/2 In.) blastholes were an integral part of the stoplng method at each mine. A true vertical crater retreat (VCR) method was used at the Homestake Mine, while a vertical bench mining method (VBM) was used at the Carr Fork Mine. VCR and VBM methods were developed In the 1970's; they offer significant productivity gain and are now used throughout the world. The new technology, however, brings with It a requirement for more sophisticated engineering design and control. Since there are no personnel in a VCR or VBM stope, all ground control Including dimensioning of stopes and pillars and the layout of cable bolt assays or other artificial support must be done in advance of production blasting. Accordingly, the objective of the research study was the establishment of a procedure for optimizing stops and pillar sizes. The approach taken was In each case a combination of mine measurements of the study stope response to mining, laboratory testing for rock properties and In situ stress measurements of the premining stress field, and theoretical calculations of the study stope response to mining. All calculations were done with the UTAH-II finite element computer program. Simulation of the blasting sequence gave a correlation of 0.88 between measured and calculated extensometer readings (Incremental relative displacements) at the Carr Fork Mine where other 30 Instrumentation boreholes were used to monitor the test stope response. A correlation of 0.84 was obtained at the Homestake Mine where 19 instrumented boreholes were used for monitoring purposes. These high correlations validated the computer mode and calibrated It for rock mass properties. The calibrated model was then used In parametric studies of alternative design layouts.

Jan 1, 1985

By W. J. Fullerton

This paper is one of a series prepared for the United States Bureau of Mines discussing the methods used in crushing and grinding materials for cement manufacture, and deal particularly with the methods used at the Howes Cave plant of the North American Cement Corporation. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of total production costs might in many instances cause embarrassment to individual producers as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue.

Jan 1, 1932