Search Documents

By Richard F. Hewlett

This Bureau of Mines report presents the computer programing methods and mathematics required to generate either random numbers or normal random numbers to be used for the construction of statistical probability models for simulating mineral deposits by Monte Carlo techniques . Theoretical frequency functions are evaluated as an illustration of simulation applications . Numerical and analytical methods of simulating and dissecting some complex frequency distributions are described .

Jan 1, 1964

By A. W. Deurbrouck

Five preparation plants employing concentrating tables for washing 3/8- inch to 0 raw coal were tested. Two of the plants were washing Pittsburgh-bed coal, two were washing Pocahontas-bed coal, and one was washing Elkhorn-bed coal. Samples of the feed to and products from the tables were collected over the normal operating shift. These samples were analyzed, and complete performance criteria were determined. The results of this study show that the concentrating table is an effective fine-coal cleaner even when operating at 40 percent over the recommended 10 tons per hour feed rate. Recovery efficiencies for the 3/8-inch to 200- mesh size fraction ranged from 97.3 to 99.3 percent; maximum yield errors and ash errors were 2.4 and 1.0 percent, respectively; probable errors ranged from 0.074 to 0.115 specific gravity units and error areas from 52 to 73 square centimeters. The amount of minus 200-mesh material in the water used for feed water and dressing water to the table had no significant effect on the sharpness of the separation achieved but did have an effect on the ash content of the clean- coal product. In the one plant studied, the substitution of fresh water for plant circulating water reduced the ash content of the clean coal by about 6 percentage points.

Jan 1, 1963

By Gary E. Sherman

This report presents a Bureau of Mines study on the cost of mine permitting and compliance with environmental regulations in Alaska. It discusses permitting requirements and procedures for placer and lode mines. Placer miners must comply with recently established (1988) water quality regulations and effluent treatment requirements. To estimate the impact differing treatment options (no recycle, 100% recycling, and flocculation) have on a placer mine's rate of return, three models (1,500, 1,000, and 500 yd3/d) were simulated. Rates of return for these models show a marked decrease as effluent treatment is increased. The incremental increase in operating cost from one treatment option to the next is relatively small; however the opportunity cost of lost production if' significant and accounts for the decreasing rate of return with increased effluent treatment. Lode mines face greater costs for permitting and compliance than similarly sized placer mines as a result of the impact of the operation. Direct permitting costs for lode mines range from 2 to 6% of total project cost, with 4% the most common figure cited by industry. Total costs for permitting and compliance are approximately double those for permitting. Indirect costs associated with compliance include mitigation, monitoring, and reclamation.

Jan 1, 1991

By Walter Kawa

Bureau of Mines research on the hydrogenation of coal has been concerned with developing processes that could be used to supplement the Nation's petroleum and natural gas resources. Motor fuel was produced in a subsidized coal hydrogenation industry in Europe prior to 1945, but the process used is still not economical and other methods of producing liquid and gaseous fuels from coal are being investigated. As an aid to the planning of coal hydrogenation research, a literature survey was made of processes or methods of hydrogenating coal that differ from the subsidized or conventional process. This report contains a bibliography of unconventional methods of hydrogenating coal and a brief discussion of the economics of the conventional method. A general discussion of unconventional methods is included, and the advantages and disadvantages are pointed out where possible. The survey supplements a previous Bureau of Mines survey3 and a comprehensive review published in 1930.4

Jan 1, 1964

By David R. Jessey

Water pollution problems associated with surface metal/nonmetal mines throughout the United States were assessed. Three major problems were identified: acid mine drainage (AMD), toxic concentrations of heavy metals and excessive sedimentation. Several factors affect the type and amount of pollutants generated at a mine site. Among these are hydrologic regime, geology, mineralogy, topography, climate, size of the mineralized area and mining method. Nine surface mines situated in distinctly different settings were visited and their pollution problems studied. These mines were located in Morenci, Arizona; Hayden, Arizona; Sauharita, Arizona; Cobalt, Idaho; Spruce Pine, North Carolina; Iron Mountain, California; Butte, Montana; Fernwood, Idaho; and DeLamar, Idaho-Oregon. A detailed evaluation of the pollution problems at the Morenci mine indicated that a diversion system and treatment pint would be the most effective means of abatement for the existing water quality problems. Based on the study of the Morenci mine and three other porphyry copper mines with differing problems a water management plan was conceived for a new source copper mine. A companion Appendix Volume containing detailed reports on the mine site visits is on file at the US Bureau of Mines Spokane Research Center.

Jan 1, 1981

By H. H. Fields

The Bureau of Mines conducted research to determine the effectiveness of long holes drilled in solid virgin coal in degasifying an area of the Pittsburgh coalbed showing that horizontal holes drilled into a virgin coalbed from the bottom of any shaft will effectively remove methane gas in commercial quantities from the Pittsburgh coalbed. The in situ pressure at a depth of 214 feet into the coalbed and the average gas and water flows from the five degasification holes were 3 lb/in2 gage and 860,000 ft3/d and 1.7 gal/min, respectively. On June 19, 1975, after 593 days of degasification, a compressor was installed and pipeline quality gas was introduced into a commercial pipeline. As of June 1, 1976, after 1,022 days of degasification, over 753 million cubic feet of gas had been drained and 117 million cubic feet of gas had been purchased by the gas company for use in the local community of Wadestown, W. Va. The gas drained to date is six times the gas estimated to be in the area subtended by the holes. Methane emissions at the working face of 1 West mains, Federal No.2 mine has been reduced by 50 pct, proving the value of methane drainage by horizontal degasification holes drilled from shaft bottoms ahead of mining.

Jan 1, 1976

By J. F. Barkley

"The fly-ash problem of the smoke-abatement engineer - who now might well be titled, ""Smoke and Fly-Ash Abatement Engineer"" - starts with the necessity for him to know what fly ash really is, what plants really create it, and how much is being created. Fly ash in this connection may be defined as all solid particles emitted to the atmosphere as a result of the combustion of fuel.COMPOSITION OF FLY ASHMuch can be learned about fly ash by studying samples with a strong magnifying glass or, preferably, a high-power microscope. As an example, figure 1 is a photomicrograph of an underfeed-stoker fly ash weighing 23.7 pounds per cubic foot, which passed a baffle-type cinder catcher and was caught by a Cottrell precipitator. Figure 2 shows a similar fly ash made at a higher stoker rating and weighing 36.2 pounds per cubic foot. The lighter ash contains more light, unconsolidated ash than the heavier. In both instances some of the ash has been fused to a glass, as is indicated by the spherical particles resembling marbles; however, the heavier dust contains more and larger spheres. With the faster burning and higher air pressures occurring at the higher burning rates, more of the larger fused spheres reached the precipitator.Such studies of fly ash frequently make possible correct determination of its source. For example, the Supreme Court Building, one of the finest of the Federal buildings in Washington, was having considerable difficulty with fly ash from some outside plant. It was thought to come from a nearby apartment house. A fly-ash trap was installed there, and care was taken in the operation of their underfeed stokers. The fly-ash nuisance continued. Microscopic examination of the fly ash found about the building compared with samples taken from the stack of the apartment house showed to the surprise of the accusing building superintendent that the present source was elsewhere. By the same means, the source was found to be a plant about ore-half mile away."

Sep 1, 1939

By James L. Eirls

Tracor MBA under a contract to U.S. DOI Bureau of Mines designed, developed, fabricated and demonstrated a conveyor belt service machine. It is self-contained, battery powered, rubber tired and capable of handling, storing and transporting conveyor belting, wire rope and associated structures for sectional conveyor belts. While moving the tail section to its next position the machine discharges the belting, wire rope and belt structures. The belting is elevated and separated to provide for the insertion of the structures with minimum expended effort. A hydraulic system provides the power for steering, braking, winding or unwinding under controlled tension the belting and wire rope, operating a load-bed slat conveyor, raising, lowering and locking connection hitches and powering external hydraulic tools. Also, a pneumatic system is available to operate air impact tools. The service machine, with its present components can function in coal seams as thin as 48 inches, double wind conveyor belting 42 inches wide, 400 feet long, load or unload 3/4" wire rope on two separate reels and is controlled by two operators. A complete belt move using this machine requires only four workers. Successful underground demonstrations were conducted in coal mines located in West Virginia and Kentucky.

Jan 1, 1983

By C. Harry Benedict

This paper presents the details of milling practice and costs at the conglomerate mill of the Calumet & Hecla Consolidated Copper Co., Lake Linden, Mich., and is one of a series on milling methods being published by the Bureau of Mines. GENERAL DESCRIPTION The mines of the Calumet & Hecla. Consolidated Copper Co. are located in the Keweenaw Peninsula of northern Michigan. The mines of this district lie in a belt not over 4 miles wide and 100 miles long, which contains more or lees commercial ore. The Calumet & Hecla properties are the farthest north, except for the Seneca, of the operating mines. The district borders on Lake Superior, and by means of the Portage and Torch Lake waterways the largest lane vessels, can transport coal and other supplies from the lower Lakes directly to the company docks.

Jan 1, 1930

By Don Belsher

Work on contract H0272007 is summarized for the period of 1 February 977 to 1 February 1978. The initial evaluation of two potential systems for the location of well casings, voids, and tunnels in coal are described. The pulse measurement equipment used for the evaluation of the antennas selected possible use with a pulse time domain system and an FM-CW system is described. A TEM horn antenna design potentially suitable for use with these systems is given. An operational comparative analysis between various antenna types is presented.

Jan 1, 1978

By Doss H. White

The value of non fuel mineral production in Alabama in 1991 was $539.9 million, a decrease of $20.7 million, a result of the nationwide recession that was felt throughout the State's economy. The 3.7% decline in mineral sales was due primarily to a slowdown in construction, which had a major impact in the construction minerals mined instate. Production and sales of crushed stone and sand and gravel fell significantly below the value reported in 1990. Despite the recession, Alabama moved from 21st to 20th place nationally in mineral value. Mineral industry developments in 1991 were primarily in the metals manufacturing sector. Reynolds Metals Co., Sheffield, celebrated 50 years of operation in Alabama. During the November celebration, the company dedicated a $121 million expansion that included a new casting facility and sheet rolling operation. Gulf States Steel Corp., Gadsden, completed the first full year of operation of its new multimillion-dollar continuous caster.3 The Foundry of the Shoals Inc., Florence, replaced two coke-fired furnaces with electric furnaces.

Jan 1, 1993

By J. A. Woolf, A. P. Towne

"INTRODUCTION A considerable part of the metallurgical work of the Precious Metals Section comprises ore-testing experiments on ores selected as representative of various mining districts on areas. Projects authorized by the Bureau and assigned to the Precious Metals Section generally include only those ores or tailings in which the precious metals are the main valuable constituents; however, there are also included ores that contain strategic or critical metals in addition to the precious metals. The recovery of strategic and critical minerals is the most important phase of the treatment of this latter class of ores. However, if a considerable percentage of the precious-metal content of such ores can be recovered without complicating the flow sheet too much, it may be possible to treat an ore for the recovery of strategic or critical metals that could not otherwise be treated at a profit.Standard testing procedure involving cyanidation, amalgamation, gravity concentration, and flotation, or a combination of these methods, is employed in the greater part of this work. However, as the complexity of the ores furnished for this work has increased, it has been necessary to include special applications of standard procedures in many instances, Standard methods of conducting tests and the purposes of the work as a whole have been discussed in previous reports 4/ of ore-testing studies. In the present report, whenever it has been necessary to apply some special phase of standard treatment, this has boon explained in detail in that particular section of the report."

Aug 1, 1944

By J. E. Shelton

This presentation covers the results of laboratory studies conducted by the Bureau of Mines Mineral Dressing Section, Northwest Electrodevelopment Laboratory, Albany, Oreg., on alluvial sands from Dismal Swamp, Bear Valley, and Cascade, Idaho. The search for radioactive minerals has led to the reexamination of alluvial deposits; in the process of this reappraisal the frequent presence of minerals bearing columbium and/or tantalum was toted. Because of increased demand for these metals by the defense industries and because these industries depend upon foreign sources for their supply the domestic alluvial black sands are being considered, as a possible domestic source. However, utilization of these alluvial deposits depends upon development of methods of concentrating these valuable minerals. The primary objective of the test work was the study of the effect of attrition scrubbing, sizing, magnetic, electrostatic, and gravity separa¬tion as methods for concentrating and recovering the columbium and tantalum-bearing minerals, samarskite, euxenite, ilmenorutile, and columbite.

Jan 1, 1955

By R. H. Nafziger

Bureau of Mines research has shown that very low-sulfur pressure vessel steels with improved mechanical properties can be prepared by two melting processes. Four pressure vessel steels having sulfur contents ranging from 0.0008 to 0.0040 wt-pct, were produced by the electric-arc furnace or by the electroslag processes. Calcium carbide was used as a desulfurizer in the electricarc furnace. Fluxes containing at least 40 wt-pct CaO provided sufficient desulfurization during electroslag remelting. Element recoveries were higher for electroslag remelting than for metal melted in the electric-arc furnace. Bar rolled from electroslag-remelted ingots generally possessed higher tensile strengths and ductility than bar rolled from it t melted in the electric-arc furnace. Charpy V-Notch upper shelf energies were also improved as a result of electroslag remelting. The primary failure mode during impact testing was was microvoid coalescence. Sulfide inclusions were minimal, especially in the electroslag-remelted material.

Jan 1, 1979

By T. A. Sullivan

The work described in this report was undertaken to evaluate and develop techniques for determining the oxygen content of titanium and titanium alloys. Early investigations of volatilization techniques involving halogenation were unsuccessful. Later efforts were concentrated on evaluating vacuum fusion and inert-gas fusion techniques. Two vacuum fusion methods and an inert-gas fusion method were found to be satisfactory in the 0.02 to 1.00 pct., oxygen range. These methods are described in detail. The coefficient of variation by any of the three methods is approximately 5 pct, While the main portion of this paper is devoted to the vacuum and inert-gas fusion methods, a resume of other suggested methods for analyzing titanium for oxygen also is given. INTRODUCTION The Federal Bureau of Nines has conducted research on titanium metal since 1938. This research included development of the Kroll process for the production of titanium (2)4, various sodium reduction processes for making titanium metal and lower valent titanium chloride-sodium chloride mixtures (17), and a fused salt electrolytic process for Me production of high-purity titanium metal and the recovery of titanium by electrorefining from off-grade materials (20).

Jan 1, 1961

By Robert E. Hershey

1. This investigation shows that the most important beds in Claiborne County, from the standpoint of present production and reserves, are the Coal Creek and Jellico. Together, they contain 69 percent of the known recoverable reserves in the county. Reserves in five other beds are tabulated in this report; in order of quantity of reserves, they are: Blue Gem, Lower Pioneer, Pewee, Big Mary, and Rex. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 60 million tons, as of January 1, 1953. Of this total, 55 million tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager to permit making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1956

Collins Radio Company, through this contract with the Bureau of Mines, has conducted a System Study of Coal Mine Communi¬cations. The program was a three phase program to establish a data base, perform communication system analysis and optimi¬zation, and prepare equipment specifications to be included in this final report. At the start of establishing a data base both a knowledge of mine communication and coal mines in general was obtained. Communication system requirements and constraints were determined along with a survey of current and potential mine communication equipment. An investigation was completed concerning theoretical LF and VLF propagation characteristics, and UHF propagation tests were conducted in a working coal mine. Different mines were contacted and on-site surveys completed with respect to coal mine communication requirements.

Jan 1, 1973

By Jack C. White

The purpose of this Bureau of Mines research was to determine the technical feasibility of direct sulfuric acid digestion of Florida land-pebble phosphate matrix. Preliminary tests in a continuous digestion circuit showed that 92 to 96 percent of the P2O5 contained in the matrix was extracted, while the P.05 concentration in the product acid ranged from 21 to 30 percent. The waste filter cake contained about 1 percent P205 and up to 18 percent water. These sandy compact filter cakes, comprised mostly of quartz and gypsum, appeared to be suitable for backfilling and reclamation of mined lands.

Jan 1, 1975

This document is Volume II of a two-volume report on underground and surface coal mine fires occurring between 1950 and 1977. Volume I discusses the methods of data acquisition, data analysis procedures, results and conclusions. This volume contains (1) a master list of all fire incidents obtained from MSHA reports, (2) an annotated bibliography of all MSHA reports, journal articles on selected incidents, and non-reportable fires (appendix), and (3) indexes to be used in accessing incidents in the master list and annotated bibliography. These three types of information provide the reader with a complete summary of coal mine fires during the period from 1950 through 1977 and a convenient means to locate incidents of specific interest. The body of this volume is organized around two tables and a series of indexes. The two tables are master lists of underground and surface fire incidents. They are followed by 14 indexes keyed to the master list and annotated bibliography. The appendix contains three different parts: o The annotated bibliography of MSHA fire reports (one section each for underground and surface mine fires) o The annotated bibliography of journal articles about selected fires from the MSHA bibliography o A listing of non-reportable fires (one section each for underground and surface mine fires) Descriptions of the contents and use of each of the three major components of this volume (i.e., master list, indexes, and appendix) are presented in Section 2.0.

Jan 1, 1979

Effective control of respirable dust is one of the most serious problems associated with longwall mining in the United States. This report describes the development and laboratory testing of dust collectors for use on double drum shearers. Systems tested included: ? High Capacity Flooded Bed Scrubber ? Water Powered Extraction Cowls ? Water Powered Extraction Drums ? Water Powered spot Scrubbers. The systems were tested using tracer gas in a full-scale model of a longwall shearer face. This report provides a detailed description of the test facility, test methods, and system test results.

Jan 1, 1982