Search Documents

By L. C. Brichta

The Canyon Diggings zinc-lead deposit is in an area of structural deformation of sedimentary rooks in Newton County, Mo., 14 miles southeast of Joplin, within the southern limits of the Tri-State district. Mining and milling on the several tracts covering the area had been carried on sporadically since 1900, and incomplete records show a production of 1,341 tonsof zinc and lead concentrates. On the northern part of the deposit the predominant metal is which occurs as galena, cerrusite, and pyromorphite in broken chert near the surface. On the southern part, lead is subordinate to zinc, which occurs mainly as carbonate and silicate minerals in brecciated chert to a maximum depth of about 150 feet. Analyses of samples from Bureau of Mines drilling indicate that approximately 77 percent of the zinc and 50 percent of trio lead i8 in nonsulfide minerals resulting from the oxidation of sphalerite and galena. Between August 12, 1948, and October 5, 1949, the Bureau of Mines investigated the deposit by churn drilling and sampling 85 holes aggregating 10,571 feet of bore and sampling two mill-tailings dumps and three mine dumps. Factual data on the investigation and the logs of Bureau of Mines drill holes are presented in this report.

Jan 1, 1950

By R. J. Leary

Oxidation testing of copper-clad steel strip was performed in a muffle furnace to determine whether copper in contact with steel scrap could be removed by oxidation in an airstream at high temperatures. Substantially all of the copper was oxidized before any significant iron oxidation occurred. The rate of copper oxidation was not affected by contact with iron. Copper oxide scale separated spontaneously from the underlying metal during cooling. Results indicate the possibility of removing light-gage copper coatings and components from ferrous scrap by oxidation in an incineration process.

Jan 1, 1965

By Thomas Novak, Robert Goldstein

The analysis of a machine-luminaire configuration is a time- consuming process requiring the construction of a machine mockup, installation of a designated lighting arrangement, and an extensive set of illumination measurements. This entire process, however, is well suited to computer analysis. By simulating the machine geometry and the characteristics of the desired luminaires, the incident light levels can be calculated at the required set of points. This Bureau of Mines paper presents a general description of the techniques involved in performing this simulation.

By Gerald T. Homce

A system capable of monitoring mine electrical power systems and detecting impending component .failure could significantly improve power system safety and reduce unscheduled equipment downtime. Such monitoring would require a method of evaluating electrical parameters, calculated from terminal values, for indications of component deterioration. The U.S. Bureau of Mines has targeted electrical failure of squirrel cage induction motors and examined the use of mathematical models to aid in this evaluation. The initial stage of this work is complete, and has produced polynomial networks called adaptive learning networks (ALN's) that can detect and quantify winding insulation leakage simulated on laboratory motors. In this modeling process, empirical data from laboratory motors were used to select the electrical parameters most significant for assessing? motor conditions, and mathematical expressions relating these parameters to simulated deterioration were formed. ALN's developed thus far can process readily measured motor terminal information and quantify power and current levels of laboratory-simulated leakage to within 1% and 3% of full load values, respectively, for motors in the 10-to 150-hp size range. The next stage of this research is validation of these ALN's for actual motor failures; this stage is currently underway, using accelerated life testing of laboratory motors.

Jan 1, 2010

By E. R. Palowitch

Two samples of the Lower Hartshorne (Spadra) bed were collected: A sample of the raw coal with the machine cuttings excluded, and a sample of the machine cuttings exclusively. Analysis of the 5-inch by 200-mesh size fraction of the raw coal, excluding machine cuttings, showed that a product meeting minimum quality specifications could be produced by washing at 1.60 specific gravity, yielding a theoretical 93.7 percent of clean coal. A negligible amount of near-gravity material at the separation gravity indicated an easy washing problem. The sample of machine cuttings had a maximum size of 2 inches and contained about 50 percent ash. Washability tests of the 2-inch by 200-mesh size fraction indicated that a theoretical yield of 30.0 percent of specification-grade coal could be achieved by washing at 1.49 specific gravity. As the machine cuttings represent an estimated 10 percent of the total coal mined, their inclusion in the mine output would increase the theoretical net yield of salable coal by only 3.7 percent. Because the machine cuttings contained a high percentage of sink 1.80 specific-gravity material, they had neither an effect on the separating gravity required to clean the raw coal nor on the difficulty of separation. Gabbing underground versus transporting the cut-tings to the surface for disposal or washing either separately or combined with the raw coal involves a number of practical, economic; and intangible factors; hence, no specific recommendations could be made. A discussion of some of the factors involved in dealing with a similar problem is given by Gandrud and Riley.4

Jan 1, 1962

By Walter Murphy

For a number of years the Bureau of Mines has been studying the properties of crude petroleums produced in the United States and the Western Hemisphere. A number of reports have been published giving the analyses of crudes from the different field and regions as made by the Bureau of Mines Hempel method of analysis.4/ Several of these reports include analyses off crude oils from the Rocky Mountain region.5/ The search for new fields and new producing horizons in old fields in the Rocky Mountain region has been quite intensive during the last few years, and a number of discoveries have been made.

Jan 1, 1937

By Charles S. Allbright

This report describes hydrogenation of petroleum distillate fuels in bench scale equipment and the effects of hydrogenation on the storage stability and the composition of the fuels. Two distillate fuels were hydrogenated in laboratory equipment using a commercially available cobalt molybdate catalyst. Reactor temperatures were varied from 600° to 850° F and pressures from 100 to 600 psig. Product fuels were analyzed by ASTM, Bureau of Mines, mass, and infrared methods. Hydrogenation of a catalytically cracked fuel from Oklahoma crude oil significantly improved the storage stability, reducing insoluble gum formed during 9 months of storage at 110° F from 19.0 to 1.3 mg per 100 ml fuel, average. Conversion of the olefins to other hydrocarbon types varied with the temperature of hydrogenation--at 700° to 850° F the conversion was mainly to aromatics, at 650° F about 50:50 to saturates and aromatics, at 600° F principally to saturates. Processing a fuel composed of a mixture of virgin distillate and catalytically cracked stock, both from Illinois crude, at 700° F and 200 psig effected marked improvement in stability; the buildup of insoluble gum in storage was lowered from 18.3 to less than 1 mg per 100 ml fuel.

Jan 1, 1967

By John R. Parker

Work places of an underground coal mine are required (30 CFR 1719) to be illuminated while self-propelled equipment is used. Permissible machine mounted systems have been developed and applied satisfactorily to many mining operations. However, some low seam and thin seam equipment has been difficult to illuminate because reliable, direct current systems and compact, low output, low glare luminaires were not available. This program resulted in the design and prototype construction of compact, low glare luminaires and AC and DC power systems, particularly suited to resolving illumination problems on low and thin seam mining equipment. Design objectives were based on enhancing the prospects for thin seam illumination solutions through definition of a product which could challenge markets enjoyed by higher glare luminaires and through reduction of technical risks associated with any new product development as well as the MSHA certification process.

Jan 1, 1982

By Paul H. Lu

This Bureau of Mines report summarizes the analysis and eveluation of the field measurement results of a comprehensive ground control study conducted in a mechanized longwall coal mine in West Virginia. Emphasis is placed on the three basic ground control parameters: ground pressure, ground movement, and geomechanical properties. Specific topics include premining ground pressures, front-abutment pressure in the longwall panel, histories of pillar loading, differential roof-strata movement and bed separation, differential floor strata movement, entry roof-to-floor convergence, in situ moduli of rigidity of coal seam and roof and floor strata, and mechanical properties of coal and coal measures rocks.

Jan 1, 1985

By Kay E. Goldberg

The Bureau of Mines conducted a study to develop and evaluate a training workshop for mine safety training personnel. The workshop was based on the Instructional Development Institute (IDI) which has been used for nearly ten years to train educators and administrators in the application of a nine-step model for defining, developing, and evaluating instruction. The Mining Instructional Development Institute (MIDI) was developed by investigators at the University of Southern California as a two-phase project. Phase I involved the modification of the six-day IDI program (including audiovisual presentations, workbooks, games, and exercises) for use by mine safety trainers as a workshop lasting three and one-half days. Phase II involved the evaluation and validation of the prototype MIDI workshop by means of a two-stage jury of experts and a prototype field trial. On the basis of data collected in the validation process it was determined that the institute provided an effective and useful method of instruction in mine safety training and that the institute would be especially valuable for mine safety training administrators and supervisors.

Jan 1, 1980

By Thomas M. Barczak

This Bureau of Mines report investigates shield mechanics by describing the elastic response and interaction of shield components to applied vertical and horizontal displacements for various canopy and base contact configurations. This research provides information on generalized shield mechanics, which is applicable in describing the behavior of all two-leg shield supports. Utilizing mechanics of materials concepts and known kinematic relationships for two-leg shield supports, free-body diagrams are constructed for each shield component illustrating internal axial, shear, and bending moment responses required to maintain equilibrium for each load case evaluated. Predicted shield (component) responses are verified by controlled displacement of instrumented longwall shields in the Bureau's mine roof simulator (MRS). Conclusions drawn from these analyses include shield structural responses are significantly dependent upon canopy and base contact configurations. Applied displacements also significantly affect shield responses. Horizontal displacement produces different responses than those produced by vertical displacements. The direction of horizontal displacement is also significant in evaluating shield response. Applications of shield mechanics to in situ support monitoring are also discussed. An objective of this research program is to establish unique shield responses to identify in situ load conditions.

Jan 1, 1989

By Robert T. MacMillan

A process has been developed in the laboratory and expanded to semi-pilot-plant scale for recovering titania, iron, and byproducts from two types of titaniferous iron ores. A reducing roast with coke and soda ash followed by grinding and magnetic separation produced powdered iron and slag from which titania and byproducts were recovered by H2SO4 decomposition. Based on the steps tested on a. semi-pilot-plant scale supplemented by the results of the laboratory investigations, enough data are available to make a balanced flow sheet. Combined data from the laboratory and semi-pilot plant indicated that 85 to 9O percent of the titania content of the ore was recoverable and that approximately 90 percent of the iron could be recovered as a metallic-iron powder. Tahawus magnetite from the Maclntyre mine at Tahawus, N. Y., was successfully treated as follows: (1) The ore was roasted at 1,050° to 1,080° C. with carbon and soda ash, thereby reducing the iron to metal sponge and retaining the titania in the slag. (2) The metallic iron was separated, after wet grinding, by magnetic or gravity means. (3) The slag fraction was air-roasted at 850° C. and leached with NaOH to recover Na3VO4. (4) The leached solids received a dilute-H2SO4 leach to remove interfering impurities, chiefly Na2O and SiO2. (5) Titania was dissolved from the leached solids of step (4) by a H2SO4-bake followed by a water leach. (6) Titania was precipitated by seeding and boiling the resulting solution. The spent liquor was used for the dilute-H2SO4 leach in step (4). The following scheme was found to be technically feasible for recovering other byproducts of the process. (1) The gelled filtrate from the dilute-acid leach step was washed and dehydrated to produce a commercially acceptable silica gel. (2) The wash liquor containing sulfates of Na2O, Al2O3, Fe2O3, and TiO2 was combined with the highly alkaline filtrate from the wet-grind and metallic iron-separation steps, precipitating iron and titanium hydroxides, which were separated for special treatment. (3) Anhydrous Na2SO4 and Al2O3?3H2O were recoverable from the alkaline filtrate from step (2) by evaporation and carbonation, respectively, and the barren liquor was recycled to the magnetic-separation step.

Jan 1, 1952

By John C. Machisak

Employment and related injury experience of the coking industry in the United States for 1956 contained in this publication is summarized under three general sections: (A) General injury experience: Tables 1 to 9: Current and comparable statistics on operating data, number, frequency, and degree of severity of injuries and major accident agencies involved in the cause of injuries. Data are presented for the industry as a whole, for each type of oven, and for the States in which coke was produced. (B) Selected injury experience: Tables 10 to 15: Comparable injury data covering 5- and 10- year periods on the number and degree of severity of injuries and major accident causes.

Jan 1, 1958

By W. M. McKewan

The U.S. Bureau of Mines has established a wire rope research laboratory to examine the factors that affect the life of wire rope. A 2-in-diameter 6x25 fiber core rope was degraded on a bending fatigue machine. This was the first in a series of tests on rope of this construction and size. Baseline testing at the laboratory was reported in an earlier publication. Tensile and nondestructive tests were performed on samples of the rope to determine the relationship between rope deterioration and rope breaking strength. The tests indicated that as a wire rope nears the end of its useful life, deterioration and the consequent loss of rope strength increase at an accelerated rate.

Jan 1, 2010

High resolution seismic refraction tomography has proved to be a useful tool to effectively estimate depth of blast induced damage in a mine face. Excavation blast damage can be as shallow as 1 to 2m and requires resolution at a fraction of a meter for effective imaging. We used an accelerometer with flat frequency response to 1000Hz to record data at spacings of approximately 0.25 to 0.5m along mine walls. First arrival times from the seismic data were used to produce P-wave velocity tomograms. The tomograms show transition from low velocity zones to velocity associated with competent rock. We interpret the low velocity zones to indicate residual fracturing from blasting. Experiments on a concrete test block and at two underground mine locations give results that are consistent with fractured rock transitioning to competent rock. Our method can be applied efficiently in an underground environment to provide continuous velocity information with depth into a mine wall over a span of approximately 10m.

Jan 1, 2009

By W. W. Adams

"During the calendar year 1925 the Bureau of Mines received from the operators of several hundred mines and quarries complete accident records covering deaths, permanent disabilities, and “lost time” temporary injuries. Some of the companies, - those that participated in the National Safety Competition-also furnished information showing the number of man-hours of work performed during the year. With these two types of information it was possible to calculate the accident-frequency and accident-severity rates of the different plants. Complete and comparable reports of accidents and Man-hours of “exposure” were received from 34 underground metal mines, 59 underground coal mines, 15 underground mines producing other nonmetallic minerals, and 102 open quarries or open-pit mines. The figures in the table appended to this report show the accident severity rates and other data for each of the 34 underground metal mines and for the group as a whole. It is proposed to publish similar figures for the other classes of mines and quarries at an early date.The 34 metal mines listed in the table are situated in Arizona, Idaho, Kansas, Michigan, Minnesota, Missouri, New Jersey, New Mexico, Oklahoma, South Dakota., and Utah; they employed 5, 925 men, an average of 174 men per mine, including employees above-ground as well as underground. With but few exceptions, 50 men was the minimum number of employees in any mine. The total period of employment or “exposure” at the 34 mines was 14,612,607 man-hours, an average of 2,466 hours per man, or the equivalent of 308 work-days of eight hours for each employee. Accidents resulted in 15 fatalities, 9 permanent disabilities, and 1,950 temporary “lost time” injuries (causing disability exceeding remainder of shift). The fatal and nonfatal injuries represented 132,575 days of disability. Thus the accident frequency rate for the group was 135 accidents per million hours and the accident severity rate was 9.073 days lost per thousand hours of 1 “exposure”. The severity rates ranged from 0.227 to 88.653, while the ·range of the accident-frequency rates was from 16. 6 to 307 .4. In compiling the accident severity rates shown in the table, all accidents caused by explosives were weighted at twice the number of days actually lost, as one of the purposes of the National Safety Competition was to stress the prevention of accidents caused by explosives."

Sep 1, 1926

By George H. Popper

The Bureau of Mines has evaluated the extent of phosphate resources available for recovery by the experimental borehole mining method in the Southeastern Coastal Plain of the United States- Phosphate re- sources at overburden depths greater than 30 m are as a rule currently unsuitable for recovery through conventional mining methods because of economic, environmental, or technical considerations. In the identified deposit areas, borehole mining operations are projected to yield a more favorable rate of return and to be environmentally more desirable than conventional surface mining. Borehole mining resource estimates presented in this study are preliminary and designed to serve as a basis for future resource evaluations, as the current data base is relatively sparse and incomplete. The resulting resources have, therefore, been classified as hypothetical and speculative and are subject to up- dating as additional exploratory data become available. Hypothetical and speculative resources amenable to borehole mining are estimated to total about 385 billion metric tons (rat) of phosphate matrix with a minimum in situ grade of 5 pct P205. With projected borehole mining capabilities and current conventional beneficiation procedures, this resource would make available approximately 64 billion mt of phosphate rock product at an estimated grade of 30 pct P205.

Jan 1, 1985

By N. A. Eilertsen

Mining operations were in progress at the Shawangunk mine near Summitville, Sullivan County, N. Y. as early as 1843 and again as late as 1918. Difficulty in effecting mechanical separation of sphalerite and galena was the primary reason for abandonment by various operators. The Bureau of Mines investigated this mine by diamond drilling, sampling, and performing beneficiation tests. The investigation included the construction of 1.25 miles of access road and the completion of 6,526 feet of core drilling in 24 holes. In addition, 151 samples were taken in the mine. The investigation proved an extension of ore contiguous to the old mine workings and resulted in the discovery of another ore shoot at depth. The ore occurs as fissure filling in a fault zone and contains concentrations of zinc and lead sulfides with minor dissemination of chalcopyrite in a quartz gangue. Metallurgical tests indicate that the ore can be concentrated by selective flotation.

Jan 1, 1950

Since roof falls in the vicinity of the working face in underground coal mines are a major source of fatalities and injuries in this country's coal mines, it is evident that the present systems of temporary support for use in this working area are ineffective. This seems to be chiefly due to the inconvenience of setting up heavy and awkward devices such as jacks, posts and the like, which also interfere with the movement of men and machines in this critical working area. This program was concerned with defining and testing commercially available materials that could be used as support elements in a more convenient flexible personnel shield. The objectives of this program were to: 1. survey the materials that might provide the support elements of a flexible-material personnel shield for use in underground coal mines and prepare a list of those materials which appear most suitable for use in coal mines. 2. prepare a proposed testing plan for the materials to be selected from the aforementioned list by the Bureau of Mines for further evaluation. The test plan was designed to provide the following information: a. Tensile strength. b. Proportional limit. c. Creep characteristics at room temperature. d. Elastic properties depicted by stress-strain curves. Properties were tested in two directions for woven fabrics. e. Density. f. Resistance to abrasion. g. Resistance to attack by mine atomsphere. h. Resistance to humidity. i. Impact characteristics.

Jan 1, 1972

By W. Dan Walker

In recent years the Federal Bureau of Mines tested and approved four new types of self-contained breathing apparatus and a facepiece designed for use with the McCaa 2-hour self-contained oxygen breathing apparatus. The Bureau also developed and perfected a battery-powered lifeline telephone for use in mine rescue and recovery operations. Some of this equipment is described in Bureau of Mines Information Circular 7413.4/ This publication is a revision of information Circular 7413 and presents pertinent information on more recently developed mine rescue equipment. The breathing apparatus described herein are 1/2- and 3/4-hour sell-contained types of much simpler design than the conventional 2-hour self-contained oxygen breathing apparatus ordinarily used by mine rescue crews; however, it is just as important to select rescue crews carefully and to train them properly in the use, care, and limitations of the newer types of apparatus as well as the older, established types, if the newer types are to be used safely. The Bureau of Mines recommends that 1/2- and 3/4-hour self-contained breathing apparatus be used only as auxiliary equipment in mine rescue and recovery work and that the capabilities and limitations of the apparatus should be well understood by those who wear the equipment.

Jan 1, 1957