Search Documents

By Steven J. Schatzel, Robert B. Krog

Frictional ignitions are defined as the ignition of a flammable mixture of methane and air that is initiated by frictional heating. Ignitions created through the addition of energy from open flames and exposed electrical circuits are not included in this analysis. Energy released in a roof fall that creates a spark and ignites a methane mixture would be considered a frictional ignition. Frictional ignitions represent the majority of all ignitions in underground coal mines. Over the study period of 1983 to 2005, a total of 1993 ignitions were reported in underground bituminous coal mines in the United States, of which 1589 were frictional ignitions. Reportable ignitions to the Mine Safety and Health Administration (MSHA) are any unintentional occurrences of flame underground regardless of duration. Frictional ignitions were reported in 155 mines and 13 states. Continuous miners represented the largest source for frictional ignitions with 1090 (68.6% of all frictional ignitions). Longwall mining operations represented the highest concentration of frictional ignitions during this study period with 1365 frictional ignitions (85.9% of all frictional ignitions). The 17 mines with the most frictional ignitions were all longwall mining operations and had 1130 frictional ignitions (307 from the shearer) that represented 71.1% of the total. In 1983, mines with frictional ignitions represented 6.9% of operating underground mines and 36.6% of total underground coal production. The percentage of operating underground mines with frictional ignitions and their total production has increased steadily and in 2005 represented 9.8% of active mines and 46.2% of underground coal production. The three coalbeds with the highest number of frictional ignitions (Blue Creek, Pittsburgh No 8, and Pocahontas No 3) had 1049 ignitions that represented 66.0% of all frictional ignitions. The three states with the highest number of frictional ignitions were Alabama (710), Virginia (247), and Pennsylvania (242) that represented 75.5% of the total. Frictional ignitions peaked in 1991 with a high of 114. In 2005, only 34 frictional ignitions were reported. If only frictional ignitions that occur at the face are considered, there have been no fatalities since 1983. Since this time, there were 33 ignitions that caused 53 workers to lose a total of 2912 working days. When including ground falls, then there have been four frictional ignitions with one incident causing two fatalities and injuring eight workers. From 1983-1991, underground productivity and the number of frictional ignitions increased. However, productivity continued to increase from 1991-2000 while total frictional ignitions fell, thereby disproving this connection between productivity and frequency of frictional ignitions. Ninety percent of all frictional ignitions occurred in underground coal mines that liberated more than 393 L/s (1.2 MMcfd million cubic feet per day) of methane through the main ventilation system. Although methane production is not the determining factor for the occurrence of frictional ignitions, it is a good indicator of the anticipated frequency.

By George A. Morgan

The production and processing of crude petroleum and natural gas are the dominant economic sectors of the Middle East. Downstream processing of these mineral fuels to petrochemicals and fertilizers is a major investment opportunity. In 1991, the 15 countries that constituted the region accounted for 26 % of world crude petroleum output, 15.3 % of world natural gas plant liquid production, and 4.5 % of world dry natural gas production. Only Cyprus and Lebanon were not crude petroleum producers. Production of these mineral fuels all declined from that of 1990 owing to the Persian Gulf War, during which output from Kuwait and Iraq either ceased owing to war damage, or was embargoed. Prior to the war, Iraq and Kuwait were the fourth and fifth largest world producers of crude petroleum, respectively. In the war, virtually all of Kuwait's production and transport facilities were destroyed or damaged. Iraq's output was embargoed from export, with only domestic sales taking place. The embargo also affected Jordan, both in terms of transshipment of materials through it to Iraq and in exports of phosphate and potash. Shipments of crude petroleum by pipeline from Iraq through Saudi Arabia and Turkey and by vessel through the Persian Gulf were terminated. However, the loss in production from Iraq and Kuwait was made up by accelerated output from other Middle East and world producers. Saudi Arabia, in particular, with its excess production capacity, accounted for the largest portion, increasing crude petroleum output by 27 % to almost 3 billion barrels.

Jan 1, 1993

By Christopher C. Jobes

This U.S. Bureau of Mines report describes a system to determine the position and heading of a mining machine during maneuvers in the face area of an operating mine section. The system is the first step in the development of a guidance system for automated mining machines. The position and heading algorithm is described, and a preliminary error analysis is performed. The sensors employed were linear position transducers mounted on a mining machine with their cables attached to points on a stationary reference. Four linear position transducers were used to provide a data redundancy that increased the reliability of the guidance system. The linear position information obtained from the transducers was processed mathematically via the position and heading algorithm to provide the desired position and heading information. The algorithm takes advantage of sensor redundancy to continually test the accuracy of the sensor data. The major sources of error were determined to be the linear position transducers, the analog-to-digital (A/D) converter used to interpret the data, and the sampling frequency of the measurement system. These sources of error were evaluated to determine their inaccuracies for use in calculating the overall system accuracy.

Jan 1, 1990

By R. Karl Zipf

Multiple seam mining interactions caused by full extraction mining, whether due to undermining or overmining, frequently involve tensile failure of the affected mine roof. The adverse ground control conditions may prevent mining for both safety and economic reasons. Prior researchers have identified the geometric, geologic and mining factors controlling multiple seam mining interactions. This numerical study examines the mechanics of these interactions using a modeling procedure that 1) incorporates the essential constitutive behavior of the rock such as strain-softening of the intact rock and shear and tensile failure along bedding planes and 2) captures the geologic variability of the rock especially the layering of weak and strong rocks and weak bedding planes. Specifically, the numerical study considered the effect of vertical stress, interburden thickness, and the immediate roof quality of the affected seam in both undermining and overmining situations. The models show that for overburden-to-interburden thickness (OB/IB) ratios of less than 5, interactions do not occur, and that for OB/IB more than 50, extreme interaction is a certainty. In between, the possibility of an interaction was found to depend on gob width-to-interburden thickness ratio, site specific geology and horizontal stress to rock strength ratio in addition to the OB/IB ratio. The models also showed that horizontal stress was profoundly altered well above or below a full extraction area and that these changes are likely to influence the success or failure of multiple seam mining. The role of horizontal stress in multiple seam mining interactions has received little attention in prior investigations. Four factors control the mechanics of multiple seam mining interactions: 1. vertical stress concentration 2. horizontal stress concentration 3. stress re-direction 4. bedding plane slip bands A combination of vertical and horizontal stress increase and high stress gradients in the vicinity of full extraction areas re-orients principal stresses into a very unfavorable direction. This seemingly small stress re-orientation has a profound adverse effect on bedded rock.

By Thomas M. Barczak, Dennis R. Dolinar, Gabriel S. Esterhuizen

Longwall mines typically use some form of standing support for secondary roof support in longwall tailgate entries. Although there have been several new support products developed for this application, there remains no universal design criteria to optimize the application of these support technologies. The requirement for optimization and proper support selection is to understand the degree of control that the support has on the ground behavior. The ground reaction curve and numerical modeling was used to evaluate the impact of standing support on ground behavior. LaModel was used to evaluate the impact of standing support on main roof and floor behavior and pillar yielding. The conclusion drawn from this study was that standing supports do not have sufficient capacity to control main roof or floor loading or prevent the resulting convergence of the tailgate entry. However, it is imperative that this “uncontrollable convergence” be considered in the support design to prevent premature failure of the support. A FLAC model was used to evaluate the near-seam roof and floor behavior in conjunction with the global vertical and horizontal stresses. The model suggests that standing roof supports can have some impact on the ground behavior as the elastic response of the rock is exceeded and rock structure deteriorates from the stress concentrations that develop around the tailgate opening. During this phase, the capacity and stiffness of the standing support can be critical to the stability of the opening, as eventually the rock mass will be transformed into a partially detached structure whose weight must be supported by the standing support. This work is part of a ground control program of research at the National Institute for Occupational Safety and Health (NIOSH) aimed at improving mine safety by reducing roof fall injuries and fatalities.

This study was conducted to determine the effects of a machine-mounted scrubber and water sprays on face methane levels. Testing was conducted in the NIOSH ventilation test gallery which was designed to simulate a full-scale mine entry. In the test entry, a model mining machine, equipped with water sprays and a simulated dust scrubber, was located at the face of a 20-ft box cut. Blowing ventilation was provided using a curtain with a 40-ft setback distance. Methane released from a pipe manifold located inby the mining machine was monitored at six locations that were 1 ft outby the pipe manifold. Tests were first conducted to evaluate the effects of using sprays and scrubber separately on face methane levels. Additional tests were conducted to determine how a scrubber used with various water spray systems would affect face methane levels. The use of either sprays or scrubber reduced face methane levels significantly. The combined use of sprays with the scrubber further reduced face methane levels a small amount. Primarily the sprays affected methane levels by changing airflow distribution close to the face.

By Paul M. Tyler

The alkali metals , sodium and potassium , and more particularly sodium , occur abundantly in chemical combination with other elements . The elements themselves are available in metallic form but are so active chemically that they oxidize rapidly in contact merely with the air . Potassium will even catch fire spontaneously in air , and both the metals will decompose water with explosive violence . Inasmuch as they are almost as soft as wax they are not suitable for the structural or other mechanical uses characteristic of ordinary metals , and consequently the uses of these elements even in the metallic condition are based upon chemical rather than physical qualities . Sodium metal is used largely as a commercial reducing agent , but potassium metal is rarely found outside of chemical laboratories . Numerous salts and other compounds of these elements enter largely into world trade and are commercially very important , but none of these compounds except sodium peroxide and sodium cyanide are made economically from the metals . Sodium is generally considered as rather an uncommon metal , but in point of annual tonnage produced it is far more important than mercury , magnesium , molybdenum , bismuth, cadmium, cobalt , gold , silver , or the various rarer metals .

Apr 1, 1932

By Thomas M. Barczak

Secondary roof support systems play a vital role in preserving the safety of underground mine workers by preventing the unintentional collapse of the mine roof. Hundreds of thousands of standing roof supports are constructed each year in underground coal mines. Historically, wood and concrete cribs and timber posts have been used for secondary roof support. These support constructions require the handling of heavy and bulky materials, causing numerous injuries to the mine workers and resulting in more than 40,000 lost workdays in the past 9 years. Since 1993, various alternative support technologies have been developed. These new support technologies not only provide superior roof support, but many also have significant material handling advantages by using smaller and lighter weight materials, fewer components, mechanically installed support systems, and pumpable support systems. The National Institute for Occupational Safety and Health (NIOSH) has conducted extensive material handling research and has developed recommended lifting thresholds to reduce material handling injuries. An analysis of roof support construction reveals that conventional support materials used in wood and concrete cribbing exceed the recommended lifting thresholds, while the engineered support systems are closer to the recommended weight thresholds. Finally, recommendations are made relative to proper lifting techniques and material handling practices to prevent injury to mine workers when constructing roof supports in underground coal mines.

Jan 10, 2000

By W. A. Calhoun

The purpose of this investigation was to develop economical mineral dressing processes for removing objectionable quantities of impurities, such as quartz and pyrite, from refractory clay deposits in east central Missouri. The presence of excessive quartz in these clays causes crazing. Pyrite causes bloating and unsightly dark blobs on the surface of fired refractory brick. The iron concentration in the proper state of oxidation may also act as nucleation centers for carbon crystal growth which can result in bursting of the refractory. Numerous deposits, representing a very large tonnage, have been examined and prospected by various refractories companies and found to contain impurities in objectionable quantities. Upgrading these clays would greatly extend our reserves of high-quality refractory clays. Wet-tabling and wet-cyclone concentration were found to be effective for removal of impurities from clays. Of the two methods, wet-cyclone concentra¬tion would be cheaper and more effective. Although wet-tabling improved the refractory properties of each clay, beneficiation by wet-cyclone produced clays of superior quality. Clay recoveries by wet-cycloning ranged from 56.1 to 81.8 percent of the weight of the crude samples, and the beneficiated clays contained from 71.9 to 94.4 percent of the total alumina. The pyrometric cone equivalent (PCE) was increased from 1 to 3 cones by wet-cycloning. The beneficiated clays also met the reheat shrinkage requirements on refiring to 1,400° C. Missouri is one of the major domestic sources of fare clay. In addition to deposits of high-grade refractory clays, there arc many deposits that contain small percentages of impurities, which render the clays unfit for the production of high-heat-duty firebrick. Development of methods to beneficiate these submarginal clays to usable materials would greatly increase commercial fire clay resources.

Jan 1, 1961

By Perry N. Halstead

This report describes two goniometers that, by simple manipulation, can be used to ascertain the attitude of a joint, vein, or fracture plane observed on the planar projection of a borehole photograph taken with an NX borehole camera of the type developed by the U.S. Army Corps of Engineers. One goniometer was designed to interpret photographs taken in vertical drill holes and the other for photographs taken in inclined drill holes. In practice, several measurements are made on each photograph with the goniometer. These data are then substituted into mathematical equations, which are derived in this report and the attitudes of fracture planes are determined.

Jan 1, 1968

To provide operators of large-opening mines with a ventilation planning tool that will help them develop a healthier, safer, and more efficient ventilation system in the underground workplace.

Jan 3, 2006

By Foster Fraas

Almost all minerals show irreversible changes in electrical conductivity after heating in the temperature range 100° to 800° C. This effect can be detected with only a limited number of minerals with the standard ionizing-electrode-type separator, which differentiates between nonconductors and conductors in the single-particle resistivity range of 1011 to 1013 ohms. Tests outside this range with other type separators, such as the static field type, increase the number of minerals with which the effect can be detected to almost all that were tested. Irreversibility may be the result of an alteration of adsorption layers, volatilization of surface cations or anions, or an oxidation or reduction. One example is limonite, which decomposes to hematite and passes through two minima and two maxima in conductivity in the temperature range 100° to 900° C.

Jan 1, 1959

By David Hill

The Australian underground coal mining industry has made extensive use of the Coal Mine Roof Rating (CMRR) classification system for a diverse range of purposes in recent years. These include mining method selection, and coal pillar and roof support design. This paper outlines a series of case histories, from large-scale feasibility studies to local support design investigations, that collectively illustrate the broad applicability, advantages, and usefulness of the methodology, as well as some of the current limitations. The key role of the CMRR in an overall hazard definition methodology is demonstrated for a major Australian project, and some ideas with regard to the future application of the CMRR, in the context of geotechnical risk management within a progressive, highly productive extractive industry, are put forward.

Jan 5, 2007

By D. Gearhart

Full-scale tests are conducted on mine roof supports using protocols developed by the National Institute for Occupational Safety and Health (NIOSH) using the unique capabilities of the Mine Roof Simulator (MRS). These protocols simulate the loading conditions that the support will be exposed to in an underground mine to determine the performance capabilities and limitations of the support. Some tests are conducted with rigid boundary conditions, creating uniform contact and near ideal axial loading conditions. These tests are used to determine the ultimate performance potential of a support, including the strength, stiffness, and stability. For prop supports where stability is a critical design issue, tests are implemented to induce buckling by a modified end condition, eccentric contact, or biaxial loading. It is important to determine the cpacity of the support design when the support is subjected to unpredictable loading conditions. This paper examines the effect of end conditions and load profiles on prop support performance and applies a new analysis methodology based on eccentric loading to determine a factor of safety for load capacity. Recommendations for installation practices that minimize eccentricity and therefore preserve capacity are also provided.

By R. P. Vinson, Abdurrahman Cetinbas, Joseph Cervik, M. G. Zabetakis

The effect of water infusion on the flow of methane and on the production of dust was investigated at an active face in the Pittsburgh coalbed. The average total flow of methane at the face decreased by approximately 79 percent, whereas the flow from the ribs increased about 24 percent after infusion. On the day after infusion, dust concentrations appear to have been reduced; however, the presence of large quantities of rock dust obscured the results on the following days.

Jan 1, 1972

By Scott W. Hazen, George W. Gladfelter

This report presents the results of an initial investigation into some problems resulting from the use of assays representing unequal sample interval lengths and the use of the weighted average grade of ore in evaluating bedded mineral deposits . A mathematical proof and examples are given to show that the unweighted and weighted assay averages are equivalent when there is no correlation between assay value and sample interval length but that these averages are different when there is correlation between assay value and sample interval length . The amount of this difference between estimates is a function of the degree of correlation . One set of sample and assay data , based on 11 stratigraphic sections of the Phosphoria formation in Idaho , indicates that the relationship between the amount of difference between estimates and the correlation factor is approximately linear . If this correlation relationship can be established , within acceptable limits of precision , as a consistent attribute of deposits , the estimate of weighted average grade of ore could be predicted directly from the unweighted estimate of grade of ore by using the relationship as a prediction factor . Randomness tests on the sample and assay data from the Phosphoria formation , using the mean - square - successive - difference method , indicate that correlation between assay value and sample interval length ( each sample interval length represents an individual bed or stratum of the formation ) , apparently has little effect on the independence between successive assays , between successive sample interval lengths , and between the products of assays and sample interval lengths . Therefore , these data can be analyzed statistically as long as the original sample sections have been selected at random for sampling .

Jan 1, 1964

By Gregory M. Molinda

The Coal Mine Roof Rating (CMRR) was developed 10 years ago to fill the gap between geologic characterization and engineering design. It combines many years of geologic studies in underground coal mines with world-wide experience with rock mass classification systems. Like other classification systems, the CMRR begins with the premise that the structural competence of mine roof rock is determined mainly by the discontinuities that weaken the rock fabric. However, the CMRR is specifically designed for bedded coal measure rock. Since its introduction, the CMRR has been incorporated into many aspects of mine planning, including longwall pillar design, roof support selection, feasibility studies, extended-cut evaluation, and others. It has also become truly inter-national, with involvement in mine designs and funded research projects in South Africa, Canada, and Australia. This paper discusses the sources used in developing the CMRR, describes the CMRR data collection and calculation procedures, and briefly presents a number of practical mining applications in which the CMRR has played a prominent role.

Jan 5, 2007

By B. D. Hanson

An interactive computer program has been developed by the Bureau of Mines which enables the user to identify the effect of cutting system changes on relative dust generation for longwall shearer drums. The program simultaneously evaluates machine and coal seam parameters, and those parameters which the user can control. The user can change one or more of these parameters at a time to determine their effect on relative dust generation, cutting forces, and/or cost. The program is written in the BASIC programming language. A complete program listing is included along with user instructions and sample outputs. This program is a more comprehensive version of the relative dustiness index (REDI) program described in Bureau Report of Investigations 8979.

Jan 1, 1988

By Thomas M. Barczak

The initial Support Technology Optimization Program (STOP),Version 1.0, was released at the 19th Ground Control Conference. This original program has since been updated to Version 2.3 which was released in May, 2001. This paper describes the additional features of Version 2.3, focusing primarily on the following three aspects: (1) including uncontrolled convergence into the design requirements for standing roof supports, (2) the addition of design procedures for cable bolts as an alternative secondary roof support, and (3) the addition of new standing roof support technologies. Another new feature which should facilitate the development of design criteria for standing roof support is the capability to define ground reaction curves through convergence measurements alone without having to make support loading measurements. There are several other new features provided in Version 2.3 which are only briefly addressed in the paper. These include: (1) additional graphics capabilities to facilitate rapid assessment of support comparisons, (2)an East-West designation for support selection to more accurately provide cost and support availability data, (3) additional safety measures including a safety factor to identify support design near the peak support capacity, checks to see if the support dimensions comply with aspect ratio requirements, and a measure of roof coverage for the design layout of the support system. These new features of STOP provide more capabilities to design and analyze secondary roof support systems for conditions which could not be fully analyzed in the original version of the program.

By Wilbur A. Haley

One of the purposes of the investigation was to determine and report on how coal augers are used to mine bituminous coal that is near outcrops and may not be mined otherwise by any other present-day method. Such increased overall recovery results in the conservation of coal resources. Other reasons for the investigation were to determine and report the production rates of such operations and the types of equipment used. Auger mining of coal as a means of coal recovery supplementary to strip mining has been introduced and developed since World War II. This type of coal mining has grown rapidly, and bituminous-coal production by auger mining has been estimated at 6,000,000 tons in 1955. Mines were selected for study to give reasonably representative information on auger mining in different types and thicknesses of coal beds in different geographic areas and on different types and sizes of equipment operated under various conditions. This report is based on field studies of 8 auger-miming operations in Pennsylvania, West Virginia, and Ohio and in 5 different coal beds. Operations were observed in active strip mines, in strip mines reopened for auger mining, and along benched coal-bed outcrops. At the time of this study, no augers were reported to be operating in underground mines. The diameters of holes drilled ranged from 26 to 52 inches, and the lengths of holes ranged up to 208 feet. At some operations auger holes often penetrated abandoned underground mine workings.

Jan 1, 1957