Search Documents

By J. R. White, S. W. Lambert, C. M. McCulloch

Examination of several coalbeds in Walker County, Ala., Cambria, Greene, and Fayette Counties, Pa., and Raleigh and Wyoming Counties, W. Va., indicates that cleat orientations are similar throughout a vertical sequence of strata. Studies of cleat orientation were carried out in underground mines that are operating in separate coalbeds vertically above one another. The data show that over a vertical separation of 100 to 400 feet, the average difference in coal cleat orientation between mines is 04° for the face and 08" for the butt cleat. Variations of coal cleat direction between coalbeds examined in strip-mined areas show similar values. Cleat orientations measured at outcrops agree well with the directions measured underground, suggesting that the amount of vertical separation between coalbeds has little effect on the resulting differences in cleat directions. The largest variation of cleat directions between adjacent coalbeds occurs where a large horizontal distance separates two sample locations. Cleat orientations for deeper coalbeds are most reliable where the data are taken from directly above.

Jan 1, 1976

By K. K. Kelley, W. W. Weller

Heat capacity measurements of akermanite ( Ca,MgSiO ) , cordierite (Mg2A14 Sig018 ) , gehlenite ( Ca₂Al₂ SiO ) , and merwinite ( Ca ,MgSiO ) were conducted over the temperature range from 50 ° to 298.15 ° K. The entropies at 298.15 K ( expressed in cal / deg mole ) were evaluated as follows : Akermanite , 50.0 ± 0.5 ; cordierite , 97.3 ± 0.9 ; gehlenite , 47.4 ± 0.4 ; and merwinite , 60.5 ± 0.5 . All four compounds have positive entropies of formation from their constituent oxides at 298.15 ° K ; the values range from 4.6 cal /deg mole for akermanite to 10.1 cal / deg mole for cordierite .

Jan 1, 1963

By L. A. Haas

The Bureau of Mines, in cooperation with three Minnesota agencies (Department of Natural Resources, Geological Survey, and the Iron Range Resources and Rehabilitation Board), investigated the potential of using glacial lake clay from Minnesota, as well as other areas, as a binder for iron ore pellets. The best clay-characterizing procedures for predicting binder effectiveness were the cation exchange capacity (CEC) using the methylene blue method and the plate water absorption test (PWAT). The best clay binder was found in the Red River Valley. However, compared to a typical western bentonite at the 0.5-pct-addition level, addition of about 2 pct Minnesota clay was required to obtain comparable unfired (green) pellet strengths. Soda ash addition only slightly improved the binding properties of Minnesota clay, but considerable improvement was obtained by the addition of a small quantity of water absorbing organic compounds. For example, with a mixture of 0.5 pct Minnesota clay or paint rock and 0.1 pct pregelatinized starch, the unfired and fired physical pellet properties were about the same as with 0.5 pct of typical western bentonite. The reduction rate at the 40-pct reduction level and the percentage of plus 6.3-mm particles from the reduction disintegration index test were also about the same.

Jan 1, 1987

"U.S. Bureau of Mines Publications and Articles, 1994 with Subject and Author Index Compiled by Office of Public Information U.S. Bureau of Mines (USBM) Department of the InteriorINTRODUCTIONThe U.S. Bureau of Mines (USBM) was established in 1910 to conduct inquiries and scientific and technological investigations on mining and the preparation, treatment, and use of mineral substances; to promote health and safety in the mineral industries; to conserve material resources; to promote economic development; to increase efficiency in the mining, metallurgical, quarrying, and other mineral industries; and to inquire into the economic conditions affecting those industries. The organic act of the Bureau, as amended by Congress and approved February 25, 1913, made it the province and duty of the Bureau of Mines to ""disseminate information concerning these subjects in such manner as will best carry out the purpose of this Act.""In accordance with this directive, USBM reports the findings of its research and investigations in its own series of publications and also in articles that appear in scientific, technical, and trade journals; in proceedings of conventions and seminars; in reference books; and in other non-USBM publications. This edition describes reports and articles published during calendar year 1994. It supplements the 50-year list of Bureau publications issued from July 1, 1910, to January 1, 1960; 1 the 50-year list of articles by Bureau authors published outside the Bureau from July 1, 1910, to January 1, 1960; 2 andthe 5-year lists of publications and articlesfrom January 1, 1960, to December 31, 1964,3from January 1, 1965, to December 31, 1969,4from January 1,1970, to December 31,1974,5from January 1,1975, to December 31,1979,6from January 1,1980, to December 31,1984/and from January 1, 1985, to December 31,1989.8"

May 1, 1995

By H. E. Harris

It has long been recognized that one of the principal ways of combating dust in coal mines is by means of water sprays. However, spray systems, currently in use, clog or plug frequently, thereby reducing the effectiveness of dust control aid, in turn, possibly increasing the health hazard to mining personnel. Moreover, the maintenance and replacement of spray system components, e.g., nozzles and filters, can be expensive in terms of direct costs of labor and material, and the consequent loss of production. Recognizing these problems, the Bureau of Mines sponsored a research project on the "Development of a Non-Clogging Water Spray System"; this project was carried out by Eastern Associated Coal Corp. The overall objective of this project was to develop a non-clogging water spray system suitable for use in underground coal mines. Since most of the dust formed is at or near the working coal face, emphasis was placed on face equipment such as a continuous mining machine. To accomplish this objective, a two-phase project was carried out. The first phase involved determining the causes of spray nozzle and spray system clogging, determining the availability of spray nozzles or systems that could be modified to be non-clogging, and developing a non-clogging water spray system. Phase two was concerned with the fabrication and the laboratory and field testing of a non-clogging system. In each phase, there were both laboratory and field investigations, and the results of these investigations are presented in this report.

Jan 1, 1975

By Albert L. Toenges

This paper is the fourth of a series5/ that describes some methods and practices of mining coal mechanically where operations are conducted on more than one shift. Many inquiries have been received regarding methods of extracting pillars with mechanized equipment, and this paper deals primarily with this phase of mechanical mining. Some of the questions that have been asked are:

Jan 1, 1942

By George W. Healy

The direct retorting of zinc sulfide concentrates in the presence of lime and carbon was examined on a laboratory scale with ten-gram charges of loose mix or fifteen-gram ones of pellets. A slow stream of nitrogen swept through the furnace tube over the boat of reactants, carrying with it the zinc vapor, which condensed on a rolled-up steel sheet near the exit, permitting weight of zinc produced to be obtained after completion of a run. Variables explored were percent of theoretical reagents, temperature, and time. During the runs gas samples were analysed periodically, and the content of CO2, CO and nitrogen were obtained. The quantities of the carbon gases could be calculated because the nitogen flow rate was measured. The gases were also examined for sulfur species, but neither COS nor SO2 could be detected at maximum sensitivity. Zinc recovery increased with excess carbon and lime and with temperature. It ranged from 77% at a ten percent deficiency to 90% at a ten percent excess at 1100°C. Going to 1200°C and theoretical reagents gave 93% recovery. Increasing time from 200 minutes to 300 minutes increased zinc yield by up to 10%. Results from sphalerite and a commercial concentrate from AMAX gave generally similar results. The reaction rate of zinc sulfide as sphalerite and of calcined sphalerite indicated that the latter reacted almost twice as fast, and recovery of zinc was five percent higher. Though the retorting step using sulfide, lime, and carbon proved to be non-polluting, it was feared that on storage the calcium sulfide in the residues would decompose, giving off noxious gases. Consequently the stabilization of the residues by oxidation was essayed. Because of the presence of unreacted zinc sulfide, the first product of oxidation was S02. Reaction of CaS to CaSO4 was incomplete, going from 20% at 800°C to 90% at 1200°C. Thus the non-polluting nature of the process as a whole is in doubt, and its economics are likely to be unfavorable compared to the traditional way of calcining the concentrates, followed by retorting of the oxide with carbon.

Jan 1, 1982

By Ronald P. Hollenbeck

The value of mineral production in Alabama increased 1 percent above the record high set in 1965. Alabama ranked second among the States in the production of bauxite, third in the production of masonry cement, native asphalt, and scrap mica, sixth in the production of portland cement, ninth in the production of iron ore, and tenth in the production of lime. The mineral industry of Alabama was dominated by the mining and processing of coal and stone, the manufacturing of cement, and the production of crude petroleum. These industries accounted for 87 percent of the State's total value of mineral production, compared with 85 percent in 1965.

Jan 1, 1967

By F. W. Horton

Investigation of an extensive deposit of chromite-bearing actinolite-talc schist situated on the summit of Casper Mountain, 10 miles south of Casper, Wyo., was one of the first projects Undertaken by the Bureau of Mines under the Strategic Materials Act (Public 117, 76th Cong., Ch. 190, 1st sess.), for which an appropriation became available August 9, 1939. During the previous summer; the Geological Survey? made? a magnetometrical survey of the area in which the schist occurred. It was exposed in several small lenses and two larger ones aggregating about 19?acres in area. Although the occurrence of chromite here had been known for many years, the only work done on the deposit was the digging of? a few shallow pits on some of the more promising outcrops. From August 23 to December 3, 1939, the Bureau of Mines investigated the larger of the two main schist bodies. Twenty-four trenches having a total length of 8,073 feet were dug across the deposit, and its subsurface extension was explored by 3,623 feet of diamond drilling. Over 32 tons of samples were shipped to the Metallurgical Division of the Bureau of Mines at Reno, Nev., for reduction, analysis, and ore testing. In all, there were 853 individual samples. Geological maps, based upon examination of outcrops, trenches, and drill cores, as well as a contour map of the area were made by the Geological Survey.

Jan 1, 1949

By Howard J. Pincus

The purpose of the study is to investigate the effects of fracture filling and associated alteration on the mechanical behavior of rocks. Results are presented for specimens from the Climax and Henderson mines in Colorado and the San Manuel mine in Arizona. The rock types studied from each location are from 1) Climax, medium-grained - granite, fine-grained granite, granite porphyry, schist, and gneiss; 2. Henderson, rhyolite porphyry; 3. San Manuel, quartz monzonite and quartz monzonite porphyry. A description of the rocks was made including: color, texture, mineral composition, composition and fabric of fracture fillings, density and porosity. Unconfined and triaxial compression tests were run on the Climax and San Manuel specimens. Sonic relocities were measured during the compression tests; Shore sceleroscope hardness was measured before the compression tests. Tentative conclusions are that some relation appears to exist between compressive strength and the following properties and features for all the specimens: dynamic Young's modulus, sonic velocity, density, rock composition, and composition and fabric of fracture fillings - veinlets. There appears to be some relation between compressive strength and Shore scleroscope hardness and porosity for quartz monzonite (San Manuel). A relation appears to exist between compressive strength and texture for schist and between com¬pressive strength and extent of failure on fracture fillings for fine-grained granite, schist, and gneiss (Climax). We plan to perform additional analyses of data collected so far and data yet to be collected in the next few months, with emphasis placed on devising a practical index of alter¬ation that can be used in the field. Limitations on interpretations arise from such factors as heterogeneity of the rocks studied, the small range of confining pressures used, and other factors presented in the text.

Jan 1, 1973

By Mark Sheppard

This paper is the second of a series recording the results of tests made at various quarries throughout the United States to determine, (1) the relation between the size gradation of feed to, and product from, primary crushers; (2) the particle shape of crushed product; (3) the differences in gradation and particle shape produced by different tries of primary crushers; and ( 4) the differences in gradation and particle shape caused by crushing different kinds of stone. Primary crushing has received comparatively little attention in the technical literature in spite of tine fact that the design of the whole crushing plant should be correlated to the performance of the primary crusher.

Jan 1, 1938

By N. B. Greninger

The U.S. Bureau of Mines conducted explosion tests on various full-scale cementitious bulkheads used in abandoned mine areas to evaluate the ability of the bulkheads to withstand gas explosion over-pressures of 20 psig. Tests were performed on 120-ft2 solid-concrete-block seals of varying thicknesses and designs. Of the seven solid-concrete-block seals tested, only the standard-type seal, having a 16-in thickness, keyed at the floor and ribs, all joints mortared, wedged at the roof, and a center pilaster, maintained its integrity when subjected to a 20-psig pressure wave. After being subjected to repeated explosions, the standard seal only showed a small hairline crack and had an air leakage of 87 ft3/min at a pressure differential of 1 in H2O. Tests were performed on cementitious foam seals of varying thicknesses and compressive strengths. Explosion tests have shown that 200-psi strength, 4-and 8-ft-thick seals can withstand a 20-psig pressure wave. At a pressure differential of 1 in H20, no air leakage was detected through the 200-psi, 8-ft-thick foam seal.

Jan 1, 2010

By J. E. Doo1ey

To process and use the heavy ends of petroleum effectively, the development of suitable separation and characterization procedures not currently available was required. A systematic procedure was developed by the Bureau of Mines using such techniques as isothermal and molecular distillation, chemical treatment, silica-alumina gel chromatography, gel permeation chromatography, and spectrometry. Using these techniques, the Bureau achieved a detailed separation and characterization of a 370° to 535° C distillate from Gach Saran, Iran, crude oil. Such a systematic procedure and the semiquantitative data resulting therefrom should be of value in selecting feedstocks and in optimizing petroleum processing operations.

Jan 1, 1973

By T. E. Gray

This report describes the preparation characteristics of the three significant coal beds in Greene County, Pa. It is one of a series planned to determine which coals are suitable for the production of metallurgical coke, either as mined or after beneficiation. Over 12.5 million tons of coal was produced in Greene County in 1956, of which approximately 10 million tons was cleaned mechanically in 8 cleaning plants. The Bureau of Mines has estimated that 3.5 billion tons of recoverable coal remained in the county as of January 1, 1954.

Jan 1, 1958

By R. G. Nelson

This report covers investigations of the Bureau of Mines for the period of June 15, 1952, to June 15, 1953, on a research project for the Materials Laboratory, Wright Patterson Air Force Base, Dayton, Ohio. The primary purpose of this investigation was to make high-purity chromium-base alloys having room-temperature ductility and high-temperature strength. The Nonferrous Metals Branch of the Bureau of Mines, Albany, Oreg., has, during the past 7 years, developed on a laboratory scale a hydrogen treatment method for making high-purity chromium that can be fabricated into thin sheet and wire. This material can be bent at room temperature. The object of this investigation was to use this material to develop improved chromium-rich alloys for high-temperature uses.

Jan 1, 1955

By E. P. Youngman

Gold and precious stones were mined in Egypt in prehistoric times. This mining, carried on at intervals, extended over thousands of years, until about 1300 A. D. Then ensued a dormant period of several hundred yoars. In the mean- time Europe made great rogress in mining practice, metallurgy, and geology and sent out various expeditions during the nineteenth century to investigate ancient mines. But the exploratory work produced no material results, and not until the beginning of the present century did actual mining recommence. The reopening of old gold mines in Rhodesia aroused interest in London and Paris, and these cities provided the capital necessary for the investigation of the ancient minee in West Africa and Egypt. Speculation resulted in the division of most of the uncultivated area of Egypt and the Sudan into huge concessions, and a number of expeditions were made; but after an unprecedented activity in West Africa, roaction set in, and the flow of capital ceased. The concession- aires, mostly individuals with insufficient capital and with a misconception of the initial difficulties of communication, water supply, and labor, allowed

Jan 1, 1932

It was decided to demonstrate the use of latex as a soil sealant by irrigating three small plots at Lanse coded 03A on the west of Brown's run, 3C on the east of the stream, and SB, an area on the spoil bank. Earlier plans to sprinkle latex on twenty acres of the side were abandoned because of easement difficulties. On the basis of results from laboratory soil columns and small plot experiments at Lanse, Naugatex J-3471 was the latex of choice. The irrigation system consisted of plastic pipe (two inch size) for the main line from the water meter to the irrigation area because of lower price and ease of handling. Because the municipal water supply was limited to 20 gpm, low-volume 14V-LA-TNT Rainbow sprinklers were specified with low angle 20° 3/32 inch nozzles to reduce wind effects. At the expected nozzle pressure of 50 psig, each sprinkler covers a 56 foot diameter area at a delivery rate of 1.64 gpm. Each of the three test areas was covered with twelve sprinklers, six used with water alone as a control area and six used with latex and subsequent water spraying. One-quarterturn inlet valves were positioned on the main lines leading to each area. Flow to the treated and untreated areas was set at 10 gpm by Dole flow control valves in the' main entry lateral to each of the six sprinklers. To avoid the use of dilution tanks, a Moyno pump operated by a 1/2 HP, 1140 rpm 5:1 reducing drive was used to deliver 1/2 gpm 48% latex for mixing with 10 gpm water. A 3500 watt gasoline generator provided power for pump and light. Latex was applied at night to take advantage of the lower evaporation and higher humidity. Neutron gauge access tubes were placed in orthogonal arrangement in the areas that were irrigated, with four tubes in the section that were sprinkled with latex and four tubes in the untreated irrigation section in each of the three locations. Each tube, five and one-half feet long and sealed at one end with a plug welded in place, was inserted five feet into the ground in a cored hole. In each irrigation area, the left section of six sprinklers spread the dilute latex while the right section sprinkled the same amount of water to serve as a control plot. As shown in Figure 7 each sprinkler has a 56-foot sprinkling diameter at 50 psig design water pressure. The sprinklers are 30 feet apart on the laterals and 35 feet apart between the laterals. The access tubes (coded AT on Figure 7) were placed in comparable spots on the two sections of each area, so that four soil moisture measurements on the two sections could be compared. Bouyoucos resistance blocks (BB) were also placed in areas 03A and 3C at one, two and three foot depths, but not on the spoil bank area.

Jan 1, 1972

By Robert G. Bottge

Hard rock mining has grown in importance in the Yukon Territory during the last 10 years while Alaskan hard rock mining has declined. One asbestos deposit in Alaska is dormant, but an asbestos deposit 55 miles to the east in the Yukon Territory is being mined by the Clinton Mine Div., Cassiar Asbestos Corp., Ltd. In this Bureau of Mines report, the economics of mining in the two locations were derived using the Clinton mine as a model. Both deposits were assumed to be of equal size and mined by similar methods. Conventional open pit mining and processing methods were assumed, and capital and operating costs were derived using flowsheets and standard costing methods. The estimated cost for the mine, mill, and support facilities in Alaska was about 30 percent more expensive than that in the Yukon Territory. The higher labor rates in Alaska were the primary contributor to the higher construction costs; freight rates added only slightly to the total costs. Approximately two-thirds of the additional annual costs of operating in Alaska were for wages and fringe benefits. The price required for the Alaskan asbestos fiber was $356.65 per ton compared with $287.44 for Yukon fiber, plus or minus 20 percent. A 12 percent discounted cash flow rate of return, 100 percent equity financing, and a rapid writeoff of assets were assumed.

Jan 1, 1975

By H. W. Sohns

A retort was constructed in which fine particles of shale, entrained in steam or other gaseous media, could be retorted at controlled temperatures and residence times and the effects of retorting variables upon quality and quantity of products could be determined. Studies of the effects of temperature upon products obtained from Green River (Piceance Creek Basin, Colo.) and Chattanooga (Tenn.) oil shales were completed. The feasibility of using the retort to process a shale of extremely high moisture content from Brazil also was investigated. Air was used as the entraining medium in a series of studies in which combustion of some of the products of retorting within the retort tube supplied a major portion of the process heat. In another series, shale oil from a conventional retort was cracked thermally to obtain data for comparison with results of retorting en-trained shale. In still another series the effects of rates of steam flow and solids feed upon rates of heat transfer from the furnace to the process stream were studied. Crushed quartz rather than oil shale was charged to the retort in this series. A study was begun in which raw shale was partly retorted, the products separated, and the partially retorted shale recharged to the retort. The shale was to have been recycled until it was completely retorted in an effort to improve oil yield by recycle retorting; however, the project was terminated before the investigation was completed.

Jan 1, 1959

By L. R. Burdick

Anthracite barley is considerably cheaper than rice. Its use, therefore, is attractive from a cost standpoint, - but its smaller size (through 3/16 inch over 3/32 inch round-mesh screen) makes it more difficult to use on some equipment when fairly high combustion rates are necessary to carry plant loads. Tests wore made in one plant to determine the performance of rice and various types of barley on a chain-grate stoker in a two-arch refractory furnace. In general, the efficiency and capacity increased with increased fuel size and volatile content. This performance is presented in tabular and curve form, together with a short review of the ignition and burning process on chain-grate stokers and a discussion of the operating procedures and limitations during the tests. In this particular installation, higher combustion rates and efficiencies could have been obtained with barley if the grate links had been designed for more uniform air flow through the grate surface. Careful maintenance and operation are particularly necessary for satisfactory results with barley on equipment not especially designed for its use.

Jan 1, 1950