Search Documents

By John A. Johnson

The first report of investigations5/ in this series pertaining to the investigation of stemming at the Mount Weather testing adit dealt with dust produced from blasting. The present report discussed the effect of stemming on eases generated by blasting, describes the test procedure, and analyzes the results from, blasting 61 standard rounds. Following care the types of stemming that are being investigated: 1, No stemming. 2. Sand in 2 paper cartridges. Clay in 2 paper cartridges. Commercial hydrated lira in 2 paper cartridges. 5. Combustible blasting plugs. 6. Ceramic is blasting plugs with clay in 2 paper cartridges.

Jan 1, 1940

By John W. Thatcher

A demountable X-ray tube vacuum spectrograph was designed by the Bureau of Mines for the determination of long-wavelength X-ray spectra from the light elements. This instrument was operated for both secondary and combined primary-secondary excitation of the aluminum K-series. There was an increased analytical sensitivity for elements in period 3, and an indication that with improved X-ray tubes or direct election excitation of the sample, X-ray determination of elements in period 2 is also possible.

Jan 1, 1965

By Roswell W. Prouty

As part of a general plan for control and economic utilization of the waters of the Missouri River Basin as well as development of its inherent power resources, the Corps of Engineers of the United States Army has under construction a rolled earth dam near the site of old Fort Randall in South Dakota. The dam is in Charles Mix and Gregory Counties on the Missouri River at a point about 922 miles above its mouth. It is approximately 125 air-line miles southeast of Pierre and 55 miles southwest of Mitchell, S. Dak. The storage reservoir to be formed by the dam will extend upstream for 150 miles and, at maximum operating pool level, will cover an area of some 107,000 acres. It will have a storage capacity of 6.2 million acre feat.

Jun 1, 1949

By T. L. Iapalucci

To determine the behavior of chlorine in coal combustion, the Bureau of Mines burned 10 chlorine-containing coals, high-, medium-, and low-volatile, in a laboratory-scale pulverized-coal combustor. At carbon-combustion efficiencies of 94 to 98 percent, 1.6 to 7.1 percent of the chlorine or an average of 4 percent of the chlorine in the coal was retained in the ash; the balance, predominantly hydrogen chloride, was evolved in the combustion gas. Sulfur retention in the ash ranged from 2.3 to 10.7 percent or an average of 6.3 percent, Addition of alkali and alkaline earth carbonates to a medium-volatile coal containing 0.27 percent chlorine by preferentially reacting with the chlorine increased the Cl/S atom ratio in the ash, Lithium carbonate addition at 0.43 percent and K2C03 at 1.59 percent increased the C1/S ratio in the ash from 0.2 to 0.6.

Jan 1, 1969

By R. Hogg, S. Chander

"INTRODUCTION The behavior of particulate systems in general is determined by the properties of the solid and fluid phases and of the interfaces between them. As particle size is reduced, the inter facial effects become increasingly important until, in colloidal systems, they become completely dominant. Interfacial phenomena are especially important in coal processing for a variety of reasons. Because coal is naturally hydrophobic and its density is low, surface forces begin to dominate over gravity at relatively coarse sizes. Coal is thermodynamically unstable in the presence of air, so that surface oxidation occurs readily leading to important variations in surface properties with time and environment. These effects are further compounded by the inherent heterogeneity of the material.Surface characteristics and properties play a significant role in most aspects of coal processing. Comminution, for example, is a process of creating new surface, while agglomeration involves the reduction of surface area and is usually controlled by surface forces. Both solid-solid and solid-liquid separations are influenced by interracial phenomena, Gravity separations are usually performed in a liquid phase and are affected by the wetting characteristics of the various solids present and by the need to ensure proper dispersion of the individual particles. Froth notation, of course, separates particles on the basis of differences in surface characteristics. Chemical processes such as leaching generally involve interfacial reactions whose rates depend on surface area and may be influenced by electrochemical effects in the electrical double layer at the solid-liquid interface, or by adsorption of reactant and/or product species from solution. Solid-liquid separations and associated processes such as flocculation are strongly dependent on the nature and properties of the solid-liquid interface.In characterizing solid surfaces, it is important to consider first the surface area, since this determines the relative importance of the interfacial effects. The structure and chemical composition of the surface may depend on the distribution of different petrographic constituents and impurities such as finely disseminated mineral matter, on the extent of surface oxidation, and on adsorption from the environment. These, in turn, will generally determine the surface properties which define particle behavior. Since the relationships between structure etc. , and properties are not generally known, it is usually necessary to measure properties such as wettability and electrical charge directly."

Jan 1, 1989

By Robert D. Perry

This report describes methods of reclaiming abandoned or inactive tailings ponds and dams. The investigated sites were selected tailings deposits adjacent to metal mines in the southwestern United States and the Pacific Northwest. The basic data developed for each site consisted of the following: a review of existing literature; a site visit that included sampling of the tailings and surrounding materials; laboratory and engineering studies; and development of reclamation plans. Laboratory tests determined the gold and silver content of each tailings deposit and the chemistry of the tailings and surrounding materials. Reclamation plans that include approximate costs were developed for five tailings deposit sites. These ranged in size from 52,000 to 103,000,000 tons. Our conclusions on the remining potential of each site are based on the tailings assay and other technical data. This study concludes that remining as a reclamation tool is feasible at certain sites. Included in this report is a remining program as part of the overall reclamation plan for two sites. Our preliminary results indicate that remining as a reclamation tool is feasible for only one of them.

Jan 1, 1981

By Gary E. Sherman

The Bureau of Mines estimated the remaining lode gold endowment of eight mining districts in Alaska using historic production data. A log-arithmic model of cumulative tonnage of ore processed versus cumulative grade was applied to the following districts: Chichagof, Fairbanks, Homer, Hope-Seward, Juneau, Ketchikan, Prince William Sound, and Willow Creek. To assess the remaining endowment, a computerized production data base was compiled from Bureau records. These data were aggregated in 5-yr intervals for each district. Data were sorted in order of declining grade, and log cumulative grade was plotted against log cumulative tonnage. Linear regression was performed on the data for each district. The linear equation for each curve was used to predict remaining endowment at a limiting mining grade. Based on conservative extrapolation of the grade-tonnage curves, a substantial total endowment of 8,415,100 tr oz of gold remains in the eight districts. The districts with the greatest remaining endowment are the Juneau, Chichagof, Fairbanks, and Willow Creek Districts.

Jan 1, 1987

By W. T. Millar

Field reconnaissance and laboratory tests on clay from South Windsor, Hartford County, Conn., indicate that the clay is suitable for lightweight aggregate raw material. Exploration of the deposit supports the conclusion that the reserves of clay are sufficient for economical mining operations to produce lightweight aggregate. Preliminary tests indicated that the clay has a short bloating range. Initial expansion occurred at 2,000° F, and at 2,100° F the clay was slightly overfired and sticky. Rotary kiln tests verified the preliminary data, and these tests showed that the clay would make a good lightweight aggregate if the processing temperature and the kiln feed sizes were closely controlled. Lightweight concrete made from the processed aggregate had properties comparable to those of concrete made from a commercial clay aggregate.

Jan 1, 1964

By Holmes, George H. Jr.

The Cherry Creek tungsten district was explored by the Bureau of Mines from April 16 to August 13, 1942. This district is in north-central White Pine County, Nev., 50 miles north of Ely. Principal work was done on the property of the Cherry Creek Tungsten Mining Co. and at the adjacent Chance mine, although the entire district was examined and mapped. The exploratory work was done in cooperation with the Federal Geological Survey and comprised surveying, trenching, sampling, long-hole and core drilling, rehabilitation of mine workings, road building, drifting, and shaft sinking. The more important tungsten occurrences were explored by trenching and diamond drilling. Sixteen holes, having a total length of 2,515 feet, were drilled. The project resulted in partial development of three new tungsten deposits and small increases in the reserve tonnage of two scheelite-bearing lenses that were being mined by the company. The following pages summarize the history of the district, outline the ownership of the properties explored, and describe the physical features and mineral deposits. Mining and milling practices at the Cherry Creek tungsten mine are outlined, and the plan and results of project work are presented in detail together with surface maps, assay maps, and drill-hole logs.

Jan 1, 1950

By M. C. Irani

This Bureau of Mines report tabulates methane emissions from U.S. bituminous coal mines with daily emission rates of at least 100,000 cfd according to States, counties, and coalbeds. Most of the methane emitted is from mines in the Appalachian States. Total daily emission in 1975 was 216.3 MMcfd, compared with 227.0 MMcfd in 1971 and 214.5 MMcfd in 1973. Thirty counties in nine States hid daily methane emissions of 1 MMcfd or more. These emitted 93 percent of the total methane. The highest emissions were from Monongalia County, W. Va., which accounted for 18.9 percent of the total. This was followed by Marion County, W. Va., 9.6 percent; Buchanan County, Va., 8.3 percent; Jefferson County, Ala., 6.1 percent; and Washington County, Pa., 5.9 percent. The Pittsburgh coalbed emitted 45.7 percent of the total methane, followed by the Pocahontas No. 3 coalbed with 12.9 percent. The report lists 196 mines, of which 60 had daily methane emissions of 1 MMcfd or more. Included in this compilation are the identification and thickness of the coalbed, methane emission, coal production and ventilation rates, number of drifts, shafts, and slopes used for ventilation purposes, shaft depth, age of mine, and gas-to-coal ratio.

Jan 1, 1977

By V. R. Miller

The Bureau of Mines conducted research on substitute brazing filler alloys with properties similar to those of silver filler alloys in an effort to conserve silver and reduce hazards from cadmium emissions. Experimental work was conducted first on the commercial silver brazing alloys BAg-I, BAg-la, BAg-2, and BAg-3 to establish criteria for evalu-ating the substitute alloys. Properties investigated included the wettability of copper, brass, and steel substrates, and the strength of joints made with the filler alloys. A series of experimental alloys containing 50 to 60 pct Cu, 20 to 28 pct Mn, and 17 to 30 pct Zn was prepared and evaluated, together with Cu-Mn-Zn alloys with 5 pct Pb or 2 pct Ni. Wetting properties and joint strengths were not as good as those for silver filler alloys, and the high application temperatures reduced the copper and brass base metal strengths. However, experimental alloys containing 70 pct Cu, 15 to 20 pct Mn, and 10 to 16 pct Sn had wetting and strength properties approaching those of the silver filler alloys. The application temperatures for these alloys were high-er than those for silver fillers, but not as high as those for the Cu-Mn-Zn alloys. With the Cu-Mn-Sn alloy fillers, copper alloy joint members are less deteriorated by recrystallization than when applying Cu-Mn-Zn alloys. The Cu-Mn-Sn system has potential for further devel-opment as a substitute brazing alloy system, particularly if the melting temperature can be reduced by the addition of other elements without decreasing the ductility and wetting.

Jan 1, 1983

By B. W. Jong

The Bureau of Mines studied reinforcement of sulfur concretes using glass, polyester, and aramid fibers. The objective of this research was to determine the feasibility of fiber-reinforcing the sulfur concrete to enhance the flexural properties. Optimum fiber sulfur concrete compositions were formulated with a cement-to-fiber ratio of 9.0:1 for glass-fiber and polyester-fiber sulfur concretes and 12.1:1 for aramid-fiber sulfur concretes. Test samples were prepared using techniques developed by the Bureau of Mines. Flexural strength values of up to 50 pct of compressive strength values were achieved with fiber additions. With non-fiber-reinforced sulfur concrete, the values ranged up to 20 pct. The impact strength and fracture toughness of sulfur concretes were increased sig-nificantly by reinforcement with glass or with aramid fiber and were adversely affected by use of polyester fiber. Strain tolerance was doubled and failure mode was shifted from catastrophic to noncatastrophic type by adding glass fiber. The glass-fiber and aramid-fiber sulfur concretes are resistant to acid corrosion and have proved durable in freeze-thaw cycles. This laboratory and field evaluation has shown that fiber reinforcement of sulfur concrete is feasible and that it enhances the flexural properties.

Jan 1, 1985

By J. J. Pfeiffer, J. W. Myers, A. A. Orning

A study was made of the feasibility of using washery refuse in the manufacture of lightweight aggregate for building materials . Preliminary caking and burning tests showed that the refuse could be converted into lightweight aggregate but that refuse passing a No. 14 U.S. Standard screen could not be used without additional processing . The aggregate was prepared by pelletizing the refuse and burning out the carbonaceous material on a chain- grate in a refractory - lined furnace . A small stationary - grate furnace was used to study the process variables involved and establish optimum ignition and combustion conditions . Maximum ignition rates were obtained at air rates of approximately 200 lb per sq ft hr , but air rates of 450 or higher were required in the burnout period to obtain temperatures high enough to sinter the ash . The data obtained from this unit were used as a guide in the operation of the chain- grate furnace . In the chain - grate furnace , satisfactory results were obtained by using primary air rates of 200 lb per sq ft hr in the ignition zone and 500 lb per sq ft hr in the burnout zone . The ignition- zone air was preheated to 500 ° F , but the air for burnout was not preheated . A total of 2-1/2 tons of aggregate was prepared in this unit and made into experimental block . A commercial development based upon the results of this study yielded a product which met the ASTM specifications C 130-42 for lightweight aggregate , and blocks made from the aggregate were of good color , durable , and light - inweight .

Jan 1, 1964

By W. G. Hopkins

The development of systems for location of miners who have become entrapped following a mine disaster has been one of the major research goals in the Bureau of Mines. This study details the preliminary development of such a system. Current technologies for locating trapped miners from the surface are either simple direction finders or time difference pulse systems that have accuracy limitations. Developing technologies using full vector field measurements at several receiving points are currently being studied. The necessity of measuring field strength with great accuracy can be a drawback in these systems. A system that operates with continuous wave radio signals, whose phase differences can be measured accurately even in weak signal conditions, greatly improves the location accuracy. A microcomputer would be used in conjunction with the system, to gather and manipulate the data to automatically pinpoint the location of the trapped miner. Comparison of this system with existing technology indicates a favorable accuracy/complexity ratio for the phase difference of arrival technique.

Jan 1, 2011

By C. C. Hustwit

The U.S. Bureau of Mines formulated a new mathematical model to characterize iron oxidation. The new model is intended to replace the currently used model, recommended by the Environmental Protection Agency (EPA), for most acid mine drainage (AMD) treatment applications. The new model was evaluated in a series of five synthetic AMD treatment tests. The initial ferrous iron concentrations ranged from 800 to 2,400 mg/L. In these tests, the Bureau model underpredicted the measured ferrous iron oxidation rates by a range of 3.24 to 8.03 pct. This was considered to be in close agreement after consideration of experimental error. The model proposed by the EPA was also evaluated using the same test data. The EPA model underpredicted the oxidation rates by a range of 77 to 100 pct in four tests and overpredicted by 19 pct in one test. The model formulated by the Bureau expresses that the rate of iron oxidation is a function of a treatment system's oxygen transfer efficiency and is independent of ferrous iron concentration when treated to near-neutral pH's. A new test method for evaluating oxygen transfer in flow-through reactors is also described.

Jan 1, 2010

By H. O. McDonald

The Bureau of Mines reviewed the chemical vapor deposition (CVD) literature of the group IVB, VB, and VIR elements. This review was utilized in the Bureau's research to provide erosion-, abrasion-, and corrosion-resistant coatings for valve components used in coal gasification units. This report attempts to bring together the many CVD references that have been published since 1966. Each of the group IVB, VB, and VLB metal coatings were reviewed, and some of their preparation methods, uses, and properties are given. A total of 160 references were found for the nine elements. Isotope separation, stronger steels, solar absorbers, alloys, superconductors, optical fibers, and coatings to increase the life of materials are some of the new uses for CVD.

Jan 1, 1979

By Donald E. Redmon

This Bureau of Mines report reviews injury experience in the nonmetallic mineral industries (except stone and coal) for 1966-67. For each of the years, 23 tables summarize disabling work injuries by department, source of injury, extent of disability, part of body injured, and nature of injury. Correlative information on employment, worktime, and operating activity is also presented.

Jan 1, 1973

By Joe H. Skidmore

This paper, describing mining and milling methods and costs at the Gold Hill mine, is one of a series being published by the Bureau of Mines. Boise Basin, in which the geld Hill mine is located, is in the central part of Boise County, Idaho, about 30 miles by air line northeast of Boise. The mine, owned and operated by Talache Mines, Inc., is at the southern end of the town of Quartzburg. About 115 to 125 tons daily is mind by square-setting and is treated in an amalgamation plant.

Jan 1, 1938

By Albert L. Toenges, Henry E. Dekay, James N. Scudder

Support of the immediate roof in coal mines is essential for their safe operation, and timbers are the most common means of support. Their effectiveness depends upon their resistance to decay. The theory has been advanced by some mine operators that rock dust, which is applied to ccal-mine workings to prevent propagation of explosions, accelerates the decay of mine timbers. As the results of part 1 of this study were inconclusive, the study was continued. Its principal objectives are: 1. To determine the effect of rock dusting upon decay of mine timber. 2. To compare the extent of decay of timbers in two mines in which underground conditions are similar. 3. To determine the loss in strength of the timbers after exposure to mine atmosphere. The studies were carried on in the Crucible mine of the Crucible Fuel Co. where the first part of this study was made, and in the Isabella mine of the Weirton Coal Co. The mines are on the Monongehela River and are adjacent.

May 1, 1943

By G. L. Oldright

This paper is the third1 of a series of five papers that is to appear on smelting in the lead blast furnace. The objects of this investigation are to determine the conditions obtaining within the blast furnace be direct experimentation, and to correlate the behavior of the furnace at various times with the main factors governing the operation of the blast furnace, and metallurgical losses. ACKNOWLEDGEMENTS The writers wish to express their appreciation to the management of the international Smelting Company at Tooele, Utah, for their kind cooperation which made possible the assembling of these data.

Jan 1, 1929