Search Documents

By B. K. Cantrell, K. L. Rubow

"The US Bureau of Mines and the University of Minnesota have developed design and performance criteria for a personal diesel exhaust aerosol sampler for underground coal mines. These are based on the premise that size can be used to separate diesel exhaust aerosol, which is mostly submicron in size, from coal dust aerosol, which is mostly greater than a micron in size. The sampler has three stages: a respirable aerosol preclassifier, a 0.8-um aerodynamic diameter inertial impactor to collect mineral dust and a final filter to collect the diesel aerosol. Using a sample flow rate of 2 L/min and gravimetric analysis to within 0.1 mg, the measure sub-0.8 um diesel aerosol has an a-priori limit of detection of 0.3 mg/m3.A miner working in an underground coal mine with diesel equipment is exposed to a wide array of pollutants from the diesel exhaust. These include CO, CO2. NO, NO2, SO2, diesel exhaust aerosol, and a variety of hydrocarbon compounds. A quantitative definition of the health risk resulting from these exposures remains elusive. During the past several years, though, progress has been made in defining the problem.Results from epidemiological studies by Garshick et al. (1988 ), animal inhalation studies by Mauderly eta). (1986), Iwai et al. (1986), and Brightwell et al. (1986) and in vitro studies by Lewtas et al. (1986) have provided sufficient data for the National Institute of Occupational Safety and Health (NOSH) to recommend that ""whole diesel exhaust be regarded as a 'potential occupational carcinogen,' as defined in the Cancer Policy of the Occupational Safety and Health Administration"" (NIOSH, 1988). NIOSH further stated that ""though the excess risk of cancer in diesel-exhaust-exposed workers has not been quantitatively estimated, it is logical to assume that reduction in exposure to diesel exhaust in the workplace would reduce the excess risk.""The Mine Safety and Health Administration (MSHA) has also been directed by an advisory committee to establish a diesel exhaust aerosol standard and to establish regulations to minimize exposure to diesel pollutants in underground coal mines (MSHA,1988). Both reports point out the need for development of measurement techniques for respirable diesel aerosol.In the past four years, the US Bureau of Mines (Cantrell,1987 and Cantrell, et al. 1987), in cooperation with Marple, et al. (1986), at the University of Minnesota's Particle TechnologyLaboratory (PTL), have studied the use of size-selective sampling techniques to measure the mass concentration of diesel aerosol in underground coal mines. Results from these studies have been used to develop design and performance criteria for a personal diesel exhaust aerosol sampler for use in underground coal mines.These criteria are based on the premise that size-selectivesampling techniques,can be used to separate diesel exhaust aerosol, which is predominantly submicron in size, from coal dust aerosol, which is mostly greater than a micron in size. In addition to the performance criteria, this paper discusses the laboratory and field test data used to develop the criteria."

Mar 1, 1992

By Bowles Oliver

"Modification of Quarry Process.Limestone beds are formed by processes of nature, processes that have been in operation for thousands and perhaps millions of years. Therefore, their com- position and physical properties are long-established and unalterable features over which man has no control. He must take them as he fields them.It is undoubtedly true that the character of lime depends largely on the nature of the parent limestone. A high-calcium lime cannot be manufactured from a dolomite, nor can a pure lime result from the calcination of an impure raw material. However, in the process of turning limestone into lime man is not entirely helpless in his control of quality. Even though a deposit is variable in character a single lime product of uniform quality may be produced by judicious quarrying. A single grade of product may not always be desired, the producer may wish to supply the needs of a variety of users each demanding U different grade or quality of lime such a series of graded products may be produced in part at least by modifying the quarry method. Thus, by changes in quarry practice a single product or a variety of products may be made. The latter problem will be considered at a later time, and the present paper devoted to the first named question' that of producing a single grade of lime from a deposit of variable rock,It is realized of course that uniformity in the product is influenced greatly by manufacturing processes such as calcining' hydrating' grinding or storage, but the present discussion is confined to the influence of raw materials only. In considering the various devices that may be employed it is realized that much remains to be learned, and it is hoped that many operators will contribute to the discussion as they have already done in connection with previous papers of this series."

May 1, 1923

By Oliver C. Ralston

Nonmetallic technologic investigations of the U. S. Bureau of Mines are headquartered at experiment stations in three widely separated localities of the United States. During 1936, the Nonmetals Division of the Technologic Branch was formally set up by combining the direction off the work of these three experiment stations under one administration. The New Brunswick (N.J.) station which in the past has been known as the Nonmetallic Minerals Experiment Station, is henceforth to be at College Park, Md., as part of the Eastern Experiment Station, and its principal activities will be related to the nonmetallic resources of the Eastern and New England States.

Jan 1, 1937

By A. Wahab Khair

"This paper presents an analysis of fracture mechanisms in coal subjected to bi-axial state of stresses, indentation of laterally confined coal specimen. Coal specimens were loaded to failure by the straight wedge indenters at various lateral confinement pressures. Strain distribution and acoustic emission characteristics of coal specimens under stress were recorded. The influence lines of vertical forces acting on the horizontal straight boundary of the coal specimen for each type of wedge indenter have been established using holographic interferometry technique. The effects of wedge indenter angle, confinement pressure, and coal anisotropy on fracture types, failure modes, and post-failure conditions were studied. The results indicated that combined application of holographic interferometry and acoustic emission monitoring techniques is not only suitable ·for studying deformability of heterogeneous and microscopically discontinuous material under stress but it also enhances the mode of fracture during the post failure stage. INTRODUCTIONOne of the relevant processes in the coal cutting technology is the application of indentation theories. Since most cutting tools in the coal industry are wedge shaped most of the indentation research is found for a wedge shaped tool.A wide range of behavior is found in different rocks subjected to the wedge penetration. A rock which is elastic brittle at standard pressure might become elastic plastic at high confining pressure (Gnirk and Cheatham, 1963). It was also observed that some rocks will merely be crushed and indented by a wedge whereas others will crack and form chips, furthermore the existence or non-existence of chips depends mostly on the geometry of the indenter, type of rock and the depth of penetration (Evans and Murrel, 1958). However, coal cutting technology is mostly explained by models which use rigid wedge to penetrate into a brittle material in which both crushing and chipping will occur (Evans and Murrel, 1958, 1962)."

Jan 1, 1988

By R. M. Santmeyers

This paper presents one of a series of digests of foreign mining legislation and curt decisions that is being prepared in advance of a. general report relative to the rights of American citizens to explore for minerals and own and operate mines in various foreign countries. This interpretation of the mining legislation of Madagascar was prepared from the best information (in French) available in Washington, but is released subject to correction and amplification, if necessary, by the proper American diplomatic and consular officers, to whom it dill be referred through the courtesy of the Department of State. INTRODUCTION The basic mining law of Madagascar is the decree of 1923, signed at Rambouillet by the President of France on July 19, and published in the Journal Official de Madagascar et Dependances. It has been modified by a number of subsequent laves and regulations, generally of minor importance.

Jan 1, 1933

By Ott F. Heizer

This paper describing the mining practices at the mines of Massachusetts, Massachusetts Co., Inc., at Mill City, Nev., is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in tie various mining districts of the United States. The author acknowledges the assistance of William C. Vanderburg, associate mining engineer, U. S. Bureau of Mines, in the preparation of this paper.

Jan 1, 1930

By R. P. Adams, R. A. Beall

The Bureau of Mines developed a method to melt and cast specimens of hafnium- carbon alloy and studied their properties . A rotating - ladle vacuum or inert atmosphere arc furnace was designed , special electrodes and molds were developed , and operating procedures were worked out for casting small shapes . The cast specimens were evaluated according to their carbon content for melting point , density , microhardness , electrical resistivity , and oxidation resistance . Lattice dimensions were determined , and metallographic specimens were prepared . Photomicrographs were taken of specimens containing 2.72 , 5.50 , 6.47 , 9.97 , 12.8 , and 15.7 weight - percent carbon , and their grain structures were compared .

Jan 1, 1963

By O. Q. Leone

Composite diaphragms were used in the investigation of electrowinning Ti from TiC14 in a fused LiCl-KCI-TiC'2 electrolyte. Composite diaphragms tested were of two general classes--those consisting of two or more solid materials, and those which contained, in addition, a loose material. An electrowinning cell using a flat diaphragm is described. The maximum current density for these diaphragms was 300 amp per ft2. Lower currents permitted longer operation times. The composite diaphragms gave electrode efficiencies that averaged approximately 60 percent, and the electrowon titanium was of good quality--some Brinell hardnesses were as low as 68.

Jan 1, 1972

By K. E. Hjelmstad

During an underground mine fire, air can be rapidly depleted of oxygen and contaminated with smoke and toxic fire gases. Any delay in warning miners could have disastrous consequences. Unfortunately, present mine fire alarm systems, such as stench, audible or visual alarms, telephones, and messengers, are often slow, unreliable, and limited in mine area coverage. Recent research by the U.S. Bureau of Mines has demonstrated that ultra low frequency electromagnetic signaling can be used for an underground mine fire alarm. In field tests of prototype equipment at five mines, electromagnetic signals from 630 to 2,000 Hz were transmitted through mine rock for distances as great as 1,645 m to an intrinsically safe receiver. The prototype system uses off-the-shelf components and state-of-the-art technology to insure high reliability and low cost. When utilized, this. technology would enable simultaneous and instantaneous warning of all underground personnel, regardless of their location or work activity, thereby increasing the likelihood of their successfully escaping a mine disaster. This report presents the theoretical basis for through-the-rock ultra low frequency electromagnetic transmission, design of the prototype transmitter and receiver, and the results of in-mine tests of the prototype system.

Jan 1, 2010

By G. W. Birge

The Bureau of Mines investigated the effect of temperature on the mechanical strength of cokes of the type normally used in blast furnace operations. Eight samples of industrially produced cokes were subjected to ASTM tumbler tests at temperatures as high as 1,100° C (2,012° F); these temperatures had no significant effect on tumbler results for cokes with stability indexes of 40.6 to 59.9. Two foundry cokes which were tested at only one elevated temperature (900° C) decreased slightly in tumbler stability. Iron are pellets made from a variety of ores and by various industrial methods were not significantly affected by temperature when tested in an oxidizing atmosphere at 1,000° C (1,832° F) by the tentative standard ASTM method.

Jan 1, 1966

By R. G. Knickerbocker

[The Electromet l'.ur.::ic'l.l LC:tt:n~ to:!'"' of' the BUl~6au 0: M_nes, Boulder City, ..rev. I invest~.f-'8tes th~ r.: nc= I (l.op itr. in tr.e redon around Boulder Dam, and thi" p2pe:.. ., 'est.3nttl t rt") d.c-velo !l'\CtltR of n seriAl of studies on "Joron uineral~ mario n.~ t~l"'t f1tn.: ... o]

Jan 1, 1940

By Robert L. Montgomery

Heats of solution of samarium (III) oxide and chloride in hydrochloric acid and of samarium (III) oxide, sulfate, and hydrated sulfate in sulfuric acid were measured. The heats of solution of this hygroscopic oxide are larger than those from the literature, probably because of more complete removal of water in the present study. From the literature value for the heat of combustion of samarium, the heats of formation of samarium (III) chloride and sulfate are -244.18 ± 0.41 and -928.5 ± 1.6 kcal./mole, respectively. The heat of hydration of the sulfate is -34.7 ± 1.0 kcal./mole. The heats of formation of other samarium com-pounds have been recalculated, using the new data.

Jan 1, 1959

By Charles A. Kumke, GROVER J. DUFF

This paper describes mining and milling practices at the San Xavier mine of the Eagle- Picher Mining & Smelting Co. in Pima County , Ariz . It is one of a series being prepared by the Bureau of Mines on mining methods in various mining districts of the United States . The mine and the mine surface buildings are situated in sec . 11 , T. 17 S. , R. 12 E. , in the Sierrita Mountains in Pima County , 20 miles south by southwest from Tucson via the San Xavier Mission and Twin Buttes road ( fig . 1). A well-maintained dirt road continues southward toward Twin Buttes for 4 miles and then branches off northeasterly for 5-1/2 miles to Sahuarita , where the concentrator of the Eagle - Picher Mining & Smelting Co. is situated on the west slope of the Santa Cruz River Valley . Tho mill is connected by a railroad branch to the main line of the Southorn Pacific Railroad between Tucson and Nogales . It is generally assumed that the San Xavier silver - lead deposits became known to the Jesuits and Spaniards in the early part of the eighteenth century . However , no extensive mining operations were conducted by the Jesuits in what is now Arizona before the middle of the eighteenth century . The completion of the Southern Pacific Railroad from Los Angeles to El Paso in 1881 marked the beginning of intense activity in mining throughout the southern part of the State . The San Xavier mine produced 6,000,000 pounds of lead , considerable zinc ( exact figures not available ) and $200,000 in silver from 1897 to 1918 . The Eagle- Picher Mining & Smolting Co. re- opened the San Xavier mine in 1943 and built a 175-ton concentrator at Sahuarita . The capacity of the plant was increased in 1944 to 500 tons in order to take in custom ore . The surface rocks at the San Xavier mine are , in great part , of sedimentary origin . Limestones of various ages comprise most of the exposed sedimentaries , some quartzites and shales also being present . The sedimentaries rest upon coarse - textured , intrusive , igneous rocks comprised mainly of granite and granodiorite . The San Xavier deposit is composed of galena , sphalerite , chalcopyrite , and pyrite . Generally the individual ore bodies are small , discontinuous , and occur as irregularly spaced shoots or lenses . The present mine workings extend horizontally a distance of 2,700 feet and vertically 900 feet . Owing to ground weight, all mine openings are timbered on the levels and all stopes are square- setted and waste -filled .

Sep 1, 1950

By Harley A. Coy

This paper, describing the mining methods and practice at No. 2 mine of the American Zino Co. of Tennessee at Mascot, Tenn., is one of a series of papers issued by the Bureau of Mines presenting the mining methods and costs in various districts throughout the United States. Its purpose is to summarize methods recently put into practice whereby increased efficiency has been effected. These improvements have to do principally with mill-hole mining, slushing, contract labor, and bonuses. In general, this paper supplements earlier articles and brings them up to date. ACKNOWLEDGMENTS The author acknowledges the assistance of M. H. Newman, geologist of the American Zinc, Lead & Smelting Co.; of William Black, assistant superintendent of mines; of P. M. Arthur, director of personnel; and of the engineering staff. The paper has been approved by H. I. Young, vice president and manager of operations.

Jan 1, 1930

By Thomas M. Kohler, Gerald L. Finfinger, Gregory M. Molinda

The Bureau of Mines has completed an investigation of the effectiveness of methane drainage in the Lower Sunnyside Coalbed at Kaiser Steel Corp.'s Sunnyside No. 1 Mine in Utah. Most of the previous at- tempts to drain methane gas using long horizontal holes were conducted in the Eastern Coal Province. From the high degree of success realized in these efforts and the large body of knowledge gained from associated research, it seemed natural to extend the technology to western coalfields. Previous work had indicated that properties affecting gas drainage were variable in the Sunnyside Coalbed. In an attempt to characterize these properties, four degasification holes were drilled from the out- side entries of an advancing section. The holes were drilled to lengths of 780, 1,680, 1,315, and 1,047 ft and produced initial flow rates of 50,000, 180,000, 340,000, and 240,000 f t3/d, respectively. A total of over 300 million f t3 of commercial-quality gas has been removed from the Sunnyside Coalbed. The four holes have reduced face emissions by 78 pct.

Jan 1, 1986

This volume summarizes the contract work performed over a nine-month period by Westinghouse Electric Corporation on a Cost Plus Fixed Fee Contract for the Department of Interior's Bureau of Mines. The contract has been extended primarily to carry out improvements recommended for equipment produced under the contract for communicating with and locating trapped miners. These improvements will enhance the performance and utility of this equipment for operational use in actual mine emergencies. An additional complete set of the equipment will also he furnished to the Bureau under this extension. The work of the basic contract was to design, produce and test hardware in accordance with the Westinghouse response to a Bureau of Mines Request for Proposal which was based technically on recommendations of a study performed for the Bureau by the National Academy of Engineering (NAE). The NAE study made suggestions for new equipment in three areas of need:

Jan 1, 1971

By Paul M. Tyler

"In preparing this paper the writer has perforce depended mainly upon published information, including the catalogs and pamphlets issued by importers and dealers such as the Diamond Drill Carbon Co. and J. K. Smit & Zonen. Special acknowledgment is made to various articles published by S. H. Ball. The writer of this paper, however, is alone responsible for statements herein contained and since he has often found it necessary to rationalize apparently conflicting opinions of recognized authorities on this little-known subject, he will welcome constructive criticism from the trade.Two types of diamond are extensively used for industrial purposes. One type, known as bort or bortz (boort, boart, bowr, etc.), consists of diamonds of the gem variety but unfit for cutting into gems. They may be colorless, yellow, brown, or gray. The other type, carbonado, known in the trade as ""carbon"" or ""black diamond,"" differs greatly from the white diamond, being opaque and apparently amorphous or noncrystalline. Actually, instead of forming a large single crystal as in a gem stone, carbon diamond comprises a mass of microscopic crystals that interlock to form a tough, homogeneous material with no planes of cleavage. It is found in various colors -- black, dark green, brown, and gray -- but usually it has .a dark lustrous black surface, with a resinoid or submetallic appearance, often resembling fine-grained steel. Upon exposure to the air the broken surface gradually darkens to an ash-gray color. Ballas is a special type of carbonado in which the crystals are definitely-oriented around a central nucleus. They are harder and tougher than ordinary carbonado but are much scarcer. The Cape ballas is reputed to be not quite so tough as Brazilian ballas but tougher than carbon or bort.The diamond crystals are isometric and take a variety of forms. The cleavage is octahedral and well marked. A crack is easily -started parallel to an octahedral face, and bort or gem diamonds are notoriously brittle, especially when subjected to sudden shock. Even carbonado, while it has a high resistance to slowly applied pressures, may be chipped or broken by a sharp blow.Exposed to radioactive rays, the diamond becomes phosphorescent; this property is often utilized to distinguish it from quartz, topaz, or glass. The unusually high refractive index likewise aids in its identification in the case of a more or less transparent stone. At the temperature of the electric arc, diamond is converted into graphite, another form of Carbon but one of the softest mineral substances. At a much lower temperature, as low as 1,5620 F., the diamond may be burned like ordinary carbon in an atmosphere of oxygen, and according to some authorities there is danger of burning a diamond if overheated even in air."

Mar 1, 1932

By M. J. Ferrante

Relative enthalpies of CuBr from 298.15 to 1,301 K were measured at the Bureau of Mines to provide thermodynamic data needed for the advancement of mineral technology. The temperatures of transition were measured by differential scanning calorimetry (DSC) and the standard enthalpies of transition[ (IlH~r) by drop calorimetry. The combined results gave reversible transitions at 657 K with llH~r= 1.10 kcal/mol, at 741 K with lm~r == 0.51 kcal/mol, and at 759 K with an enthalpy of fusion (AH~) of 1.22 kcal/moL ] An anomalous increase in heat capacity preceded the first crystal transition at 657 K. Tabulated values are listed for the standard relative enthalpy, heat capacity, entropy, and Gibbs energy function from 298.15 to 1,500 K. Standard relative enthalpies are also given in equation form and combined with thermodynamic data from the literature to derive values of standard enthalpies of formation and Gibbs energies of formation.

Jan 1, 1984

By G. S. Rice

The Experimental Mine of the United States Bureau of Mines is a unique coal mine that serves as a large-scale testing laboratory. It is used primarily for testing the explosibility of coal-dust and gases but is also the workshop for many other kinds of research work of which the chief object is to increase safety in mining. The mine is situated in Allegheny County, Pa., about 13 miles southwest of Pittsburgh among the high hills of the west bank of the Monongahela River, at the northeastern edge of the gas-coal district of the Pittsburgh coal bed which extends south through the Connellsville coking-coal district into West Virginia. The Pittsburgh bed, of the Upper Carboniferous age, is one of the most extensive continuous coal beds in the United States, if not in the world. Throughout large areas it shows remarkable uniformity of thickness, levelness, and character of coal, which is a coking coal of high-grade bituminous rank. Its thickness in the northern part is 5 to 5 ½ feet and in the central and southern part is 7 to 9 feet.

Jan 1, 1933

By D. G. Kuehn

Positive ion sampling studies have been conducted on do discharges containing 0.33 percent sulfur dioxide in helium. Measurements were made for normalized gas pressures from 0.45 to 6.8 torr and discharge currents from 5 to 40 ma. Ion species observed included SO+, S+, SO2+, SO3+; O+, and 0+, 02+. Studies were conducted on the functional dependence of the various ion species with respect to axial distance, pressure, current, and gas flow rate. Interpretation of these results is consistent with the assumption of SO2 dissociation. Deposition of sulfur compounds was observed in the plasma container during these studies. The present results are compared with previous studies which have been conducted in SO2.

Jan 1, 1971