Search Documents

By W. K. Overbey

Surface fracture trace density, changes in roof rock type, and topographic unloading due to drainage were mapped for the mining areas located in the Blacksville-Osage, W. Va., quadrangles to investigate their influence on mine roof falls. Using these factors, a technique was developed to predict probable roof fall areas ahead of projected mining operations. As a feasibility test of this proposed technique, areas were delineated where one, two, and all three of these factors were operating to formulate a "potential hazard map" for comparison with roof fall observations that were made. The limited evidence suggests that in combination these factors are reliable predictors of where roof falls are likely to occur. This technique promises to be a useful tool in planning mining operations.

Jan 1, 1973

By Elizabeth A. Johnson

Minor-element behavior and interaction in the copper matte-iron silicate slag system have been studied by the Bureau of Mines. In the present work, the possibility of interactions among the minor elements As, Sb, Bi, Se, and Te was investigated. Equilibrations of matte, slag, and one of each of the five minor elements were performed at 1,250° C under typical matte smelting atmospheres of CO, CO2, and S02 for mattes containing 40, 50, and 60 pct Cu. Results are compared with those of a previous Bureau of Mines study in which all five minor elements were present simultaneously.

Jan 1, 1984

By Noel N. Moebs

The coal wants at the Westland Mine in southwestern Pennsylvania consist chiefly of elongated, sandstone-filled channels with slickensided basal contacts. Tentatively identified as washouts, these channels are about 1,000 feet long and 300 feet wide, are erratic in occurrence and trend, and are difficult to delineate from the customary core drilling pattern. Roof conditions are hazardous adjacent to the washout contact, but roof stability is generally unaffected greater than 30 feet away.

Jan 1, 1981

By Virgil J. Stachura

The Bureau of Mines conducted a series of delayed blasting experiments at a West Virginia contour coal mine that resulted in smoother highwalls. The 17; were smoother due to reduced overbreak and inherently safer A, to reduced likelihood of rockfall. Reduced overbreak was accomplished by an increase in the highwall hole delays, which changed the effective delay pattern geometry and the direction of burden movement. The blast delays in the highwall holes were 50 to 100 ms longer than the mine's nominal design pattern (flat V, 17- by 42-ms surface delays, 200-ms in-the-hole delay). The burden movement was effectively changed from a 45* angle to 90* with respect to the highwall. The results of the blast delay changes were evaluated using terrestrial photogrammetry to generate vertical profiles at regular intervals. This evaluation showed that delay changes produced generally smoother vertical profiles.

Jan 1, 1984

By W. A. Dunkley

During the past year and a half the Western United Corporation of Aurora , Illinois , has been distributing carburetted water ges from its Lockport , Ill . , plant , to an extensive territory , under an initial pressure ranging up to 90 lb.. per sq. in . The most distant distributing point on the system is at Harvard , Ill . , about 35 miles from the plant.. The territory supplied is approximately 85 miles long and 35 miles wide , the total mileage of rains being 1223 , or approximately 24 per cent of all the gas trains in Illinois outside the city of Chicago .

Feb 1, 1923

By J. J. McClelland

The face area of a continuous mining section of an underground coal mine is the most dangerous area in the mine. Workers there are at nearly twice the risk of death or disabling injury than those in other parts of the mine. Despite extensive training of miners and improved equipment and mining methods, fatality and injury rates have remained constant during the past few years. It is clear that advanced research is necessary to apply new technologies or modify work procedures to solve the continuing problem of the loss of lives and the numerous injuries at the mine face. A U.S. Bureau of Mines research program is developing a Reduced-Exposure Mining System (REMS) that relocates personnel operating the mining machinery at the face away from the hazards to a nearby haven of relative safety. REMS uses proven technologies of computer automation and robotics to help control the operation of the mining machines at the face, while personnel are moved away to a nearby, safe control room. In this protected, well-ventilated environment, they can supervise or control the operation of the machines while viewing what the machine is doing using video and graphic display monitors.

Jan 1, 1994

By Michael A. Trevits

During the time period from 1990-2007, there were 1601 reportable fires that occurred in the U.S. mining industry (an average of 89 fires per year). The leading causes of U.S. mine fires include flame cutting and welding operations, frictional heating and ignitions, electrical shorts, mobile equipment malfunctions, and spontaneous combustion. The National Institute for Occupational Safety and Health (NIOSH) is conducting a program of research addressing metal/nonmetal and coal mine fire prevention, detection, management and suppression. In the metal/nonmetal area, work was focused on technology transfer and training, and research to reduce the number of mobile equipment fires and their hazards. In the coal arena, research is underway to determine the root cause of cutting and welding-related fires and to evaluate the effects of ventilation schemes relative to the spontaneous combustion risk in longwall mines. Relative to fire management, research is ongoing on remote mine seal installation and remote mine fire suppression technologies. Finally, research is continuing to develop comprehensive and usable smoke management techniques and to develop mine fire growth models, propagation, and suppression. This paper presents a summary of some of the mine fire research and provides an overview of the next phase of the NIOSH mine fire research program.

Jan 1, 2010

By David L. Veith

This report summarizes a Bureau of Mines review of selected literature on the effects of subsidence due to high-extraction underground coal mining on farmland areas. The data are presented for consideration in evaluating the subsidence effects due to similar mining techniques on the prime farmland areas of Illinois. In Illinois the ground water level in the glacial drift is only 2 to 15 ft below the nearly flat to gently rolling ground surface. The main subsidence concern is flooding, as caused by the lowering of the ground surface, and the subsequent effects on crop production. Positive drainage must be maintained in the farmlands, and the need exists for extensive regional planning by the mining and agricultural industries to maximize short- and long-term production from both efforts. The Bureau is cooperating with the State of Illinois to develop basic information necessary for such planning.

Jan 1, 1987

By Byron M. Bird

"The prevailing practice of washing unsized coal, 1/2-inch and finer, to 1/8-inch and finer, on a table is subject to certain limitations which are commonly overlooked. In some instances good results are obtained by this method, but often the opposite is true and the efficiency of the washing operation is low. Although the separation taking place on a concentrating table is not fully understood, the actual distribution of particles of various sizes and specific gravities was determined a number of years ago by ore-dressing investigators. Hence this paper consists of an analysis of an old problem by new methods. The experimental data on which the discussion is based were obtained in the course of coal-washing investigations conducted by the U. S. Bureau of Mines at the Northwest Experiment Station in cooperation with the University of Washington and with certain coal operator: of that State.Experimental WorkThe general method of study has been to take a large number of zonal products from the table, and separate them according to specific gravity and size into their component parts. The table used is one of the standard commercial sizes with a diagonal deck. The coal to be washed is split into representative portions, which are stored in separate bins. One portion is used for ""timing as"" the table; the products are collected continuously in the same turned to the feed bin, and thus a closed circuit is completed. When the despite conditions on the table are obtained, coal is fed from one of the re. After the table is operating smoothly the entire product is minute; such a sample is sufficiently large to represent accurately the work of the table and at the same time to minimize the effect of beginning at the end next to the head motion, separate samples are made for each foot along the edge of the deck."

Jun 1, 1926

By Frank S. Wartman

[ ]

Jan 1, 1927

By C. L. Klingman

In extracting helium from natural gas at Bureau of Mines helium plants, a continuous analysis of the helium content of inlet and outlet gas streams is required to determine extraction efficiency. An analyzer, using established principles of gas chromatography to effect the analysis, has been developed by the Bureau of Mines to meet this need. It will record the helium content of inlet or discharge gases from helium-extraction plants every five minutes, continuously, without the attendance of an operator. A 25-inch column of activated charcoal is used as a partitioning agent; nitrogen is the carrier gas; and a hot-wire, thermal-conductivity cell is the detector. A 1.0 mv, strip chart indicates the unbalance of the detector cell, Sample size is 0.37 cc, and carrier gas flow rate is 75 cc, per minute. Significant improvements in helium extraction have been demonstrated by using the chromatograph in three helium-extraction plants.

Jan 1, 1961

By D. G. Lee

Diesel particulate matter (DPM) often contains small amounts of metal as a minor component but this metal may contribute to adverse health effects. Knowledge of the mechanism for particle formation as well as the size preference of the trace metals is critical to understanding the potential for health concerns. To achieve this, the size and the composition of each particle should be optimally measured at the same time. Single particle mass spectrometer (SPMS) would be the best tool for this objective. In this paper, we therefore will introduce new findings about the mechanism and distribution of the trace metals in DPM, derived from a study where an SPMS was used to analyze freshly emitted DPM. KEY WORDS : Single particle mass spectroscopy, Diesel particulate matter, Characterization, Metal contents

Jan 1, 2006

By L. C. IlsLey

Minin,g Qr col-cu.ttint till:I chines are 1?;\i9ng the _m9t wideiy .used de1sses ()f mining equipment.· These 1T:.i:1Chines ,.--re practicaily t-tl\·operc1_ted eiyher_by compressed .iir or by electric. ·motors. According to &.ta• compiled _ from the 122. issue COAL CATALOG\JE. OJMEINED WITH; OOAL "FIELD 'pf!:fC'TOTl1, bf 7,088. mnes from which reports were obttiined there -are 3895 mines that u.se coal-cutting eql;lipmen:ts,, 'f'hi report lists 20,031: r.ct:lchines, 17,&75 being operated by·elct:i.c.m<;>_tors··:r;id :the remtiinder by compressed i.r motors,· ,-. · ', .. . · .. ··, .. _ ,· .,, .. .. . . . . . : ; "'l t:: On tl.Ccou-nt .. of the wide· use of coc:11-cutting -.:i"cliine_- any Stat!;ls have issued regulationa as "to their operation dnd be to safety precautions that.should be observed J especially in gaseous mines.

Oct 1, 1922

By M. M. Myers

"Importance pf the small stone problem.Profitable disposal of limestone too small for making lime in the shaft kiln, is one of the most urgent problems in the lime industry. Reports received by the Bureau of Mines from 31 quarries show that the proportion of small stone varies from 2 to 40 per cent, averaging 18 per cent of gross pro¬duction, Modern methods of heavy blasting, and the use of crushers in large quarries tend to increase the proportion of small stone above that produced in early days when light blasting and hand sledging were almost universally used. There is also a growing movement toward underground operation of lime deposits, a method which in general produces a greater proportion of fines than is encountered in open-pit work. Thus the small stone problem is of growing importance, and demands the attention of every progressive lime producer. As the problem is of almost universal interest, it is urgently desired that every operator who reads this report will contribute from his knowledge or experience, answers to the questions on the final sheet.There are several markets in which small stone may be sold but in these markets the competition is generally keen and the prices low. The lime producer's chief product is lime, he understands its manufacture and marketing, and brings him a greater return than can be obtained from most limestone by-products. For these reasons it is evident that the conversion of small into lime is the nest desirable means of disposal."

Apr 1, 1924

By G. W. Jones

[One of the mJor c~ctivities of the Bureau ~f l;ine;: is the j.a-onotion of sdetp in mining a.nJ other inclus tries. 13 cor&apos;ncc tlcn td t~l tiiene activities the 3~.sccu r:e termine? t&apos;le cwl.os:lon ha~arls 95 n,o;r.?xs tibla Tases, vzpor s, aid scli3s aqi iavestig~ ter rnrI.?ns of controlling s-~fi. prevpri ting eqlosians.]

Jan 1, 1941

By G. W. Jones

[One of the mJor c~ctivities of the Bureau ~f l;ine;: is the j.a-onotion of sdetp in mining a.nJ other inclus tries. 13 cor&apos;ncc tlcn td t~l tiiene activities the 3~.sccu r:e termine? t&apos;le cwl.os:lon ha~arls 95 n,o;r.?xs tibla Tases, vzpor s, aid scli3s aqi iavestig~ ter rnrI.?ns of controlling s-~fi. prevpri ting eqlosians.]

Jan 1, 1941

By D. R. Corson

The Bureau of Mines instrumented two similarly backfilled stopes--one filled in the normal manner and the other with the fill densified using vibratory compactors--to evaluate the effect of fill compaction on subsequent vein-wall closure proposed as a adjunct process for strengthening cemented fill. Hydraulic pressure cells to monitor pressures within the fill and mechanical closure devices to measure vein-wall movement and the procedure for their installation are described. The field compaction work was generally performed manually by utilizing small commercial concrete vibrators. A prototype immersible vibrator using slusher cables to propel the vibrator in the stope was used on several lifts of fill. Although compaction efforts were less effective than anticipated in increasing the final density of fill, analysis of the field data does indicate somewhat improved strain characteristics and an increased pressure buildup for the densified fill. The effects of a prolonged period of inactivity and of rock burst occurrences in the immediate area are also reflected in plots of strain and pressure within the two instrumented stopes.

Jan 1, 1971

By Michael R. Yenchek

Contacts with energized conductors are a major cause of electrocutions in underground coal mines. Sensitive ground fault interrupters (GFI&apos;s) installed on in-mine three-phase ac utilization circuits would probably prevent the majority of these deaths. A sensitive GFI is a protective device that detects and interrupts small deadly ground currents in the milliampere range before those currents can cause ventricular fibrillation in humans. Commercially available three-phase sensitive GFI&apos;s have not been specifically designed for application in coal mines. The Bureau of Mines therefore tested three commercial GFI models to determine their worthiness for mine power systems. GFI design and construction, transient immunity, reliability, and time-current characteristics were evaluated in laboratory tests. No commercial device was found suitable for mine use without design modifications. The tests results will serve as a basis for the development of a mineworthy sensitive GFI in ongoing Bureau research.

Jan 1, 1985

By Robert D. Thomson

Sheet mica is an important material in the manufacture of electronic and electrical equipment. Large quantities are consumed each year as an essential component in generators, transformers, radios, television sets, radar, electric lighting equipment, and electrical appliances. The nature, structural imperfections, and impurities determine to a great degree the usefulness of sheet mica. Proper processing and classification add greatly to its market value. This report is designed to assist producers in understanding the complexities of marketing muscovite sheet mica. ACKNOWLEDGMENTS Special acknowledgment is due S. A. Montague, of Spruce Pine Mica Co. and G. A. Purcell, mica consultant, General Services Administration, for their critical review and many helpful suggestions in the preparation of thin report. Assistance from other industry and Government representatives is acknowledged with thanks.

Jan 1, 1955

By H. L. Gibbs

Many factors contributed to the decision to build a radiochemical laboratory at the Salt Lake City Metallurgy Research Center to investigate the application of radioactive isotopes and chemical compounds in extractive metallurgy. These reasons included the notable success achieved in biological sciences with radioisotopes, the development of reliable instruments and methods for identifying the isotopes and measuring their activities, and the commercial availability of radioisotopes in a variety of forms and known activities. The paramount reason, however, was the realization that better methods were needed for guiding and quantifying research to resolve the complex extractive metallurgy problems under study at the Research Center. This is the first of a series of reports describing the application of radioisotopes and radioactivity techniques in extractive metallurgy. The report includes a discussion of licensing and safety requirements, a general description of the laboratory and the methods used, a definition of the nature and scope of the research program, and a synopsis of the more important problems studied. Subsequent reports will concern radioactive techniques for solving specific problems in mineral dressing, hydrometallurgy, and pyrometallurgy.

Jan 1, 1960