Search Documents

By Robert M. Becker

The evaluation of existing rock stresses from measurements of the change in diameter of a borehole that is stress relieved by overcoring has become a common practice, The stress evaluation has been generally based ,on isotropic relations whereas rock in varying degrees is anisotropic. A plane elasticity solution for a circular hole along one axis of an orthotropic medium is adapted for evaluation of in situ stress from borehole deformation measurements. A consistent triaxial testing approach for determining elastic properties of the overcore is also outlined. Comparison of isotropic with anisotropic interpretations of the state of stress show that large errors in evaluation may occur if the anisotropic character of the rock is neglected.

Jan 1, 1967

By John P. Hager

This study investigated the formation of vapor complexes between aluminum chloride and the chlorides of iron, titanium, and silicon. For the A1-Fe-C1 system the proposed gaseous complex species is Al2Fe2C112(g), which is formed according to the reaction 2A1C13(s) + 2FeCl3(s) = Al2Fe2C112(g) The corresponding free energy expression was determined to be ?G° = 38091.49 - 71.45 ? T 400 < T < 600°K The vapor composition above AlC13 melts contaminated with FeC13 was calculated. In the Al-Ti-CI and Al-Si-Cl systems the proposed vapor complex species are Al2Ti2Cl14(g) and Al2Si2Cl14(g) respectively. Free energy expressions were estimated for the formation of the two complex species. Again, the vapor composition above AlCl3 melts contaiminated with TiCl4 or SiCl4 was determined. The results of this study were compared with previous studies on the three systems.

Jan 1, 1980

By Floyd G. Anderson

The Federal Bureau of Mines promotes the use of safe and effective dust-collecting devices for rock drilling in coal mines. To insure that such devices are available to the coal-mining industry, the Bureau issues certificates of performance for dust-collecting systems and certificates of approval for dust collectors and rock drills or other mining equipment with integral dust-collecting systems that meet the requirements of an established Schedule.4/ Investigations are conducted under the provisions of the current revision of this Schedule by engineers of the Branch of Health Research. This circular describes briefly the requirements and procedure for obtaining certificates of performance or approval and lists equipment that has been certified as permissible under Schedule 25 or its revisions as of January 31, 1961. The names and addresses of companies to which certificates have been issued are listed alphabetically at the end of this circular.

Jan 1, 1961

By James S. Browning

Research by the Bureau of Mines demonstrated that organic heavy liquid adhering to or adsorbed on fine mineral particles can be effectively removed by a novel method embracing pulping or displacement washing with hot water alone or in combination with a detergent. Displacement washing with steam alone or in combination with a detergent also was effective for removing the heavy liquid. In tests of sized minus 48-plus 200-mesh mineral charges, both the hot water washing with detergents and detergent steaming effectively reduced the heavy liquid losses on the particles to about 0.2 pound per ton of mineral or less. Centrifuging of the wash solutions permitted an almost complete recovery of heavy liquid from the solution as a pure heavy liquid product.

Jan 1, 1966

By T. E. Swigart

In connection with experimental work by the Bureau of Mines to determine effects of back pressure . on oil wells * , data were compiled on the engineering conditions in the oil field selected , in order to afford a more complete understanding of the wells tested , and to illustrate the extent to which underground conditions should be studied when making oil -field experiments of this nature . This report , containing the data mentioned, may be of interest to the oil industry , as it describes briefly the methods of operation employed in developing and exploiting shallow well territory .

Feb 1, 1923

By W. H. Oppelt

To provide a relatively structurally stable form of dried lump lignite, two North Dakota lignites from Mercer County were dried by the Fleissner process in an atmosphere of saturated steam at 200, 300, and 370 p.s.i.a. pressure, corresponding to steam temperatures of 382°, 417°, and 437° F., respectively. Two series of experiments were made at each test pressure with the individual lignites. In one series, the autoclave was preheated to the processing temperature before charging the lignite; in the other the lignite was charged into the autoclave at room temperature. In each case, heat losses were determined by blank tests of steam consumption over a similar operating cycle with the empty autoclave. The degree of moisture removal and net steam consumption were calculated from material balances. The amount of water removed as a liquid from the two North Dakota lignites during the heating and steaming periods was compared with results calculated from previously published data on drying Austrian lignite and Australian brown coal. These lignites, covering a wide geographical area, had original moisture contents ranging from 35 to 49 percent. The Austrian lignite and Australian brown coal are considered to be of Miocene Age, and the Dakota lignites belong to the Paleocene.

Jan 1, 1955

By E. H. Denny

Colorado coal-mine fatalities, which have gradually decreased since 1914, have shown a marked decline since 1924. Data on coal-mine fatalities in Colorado published by the U. S. Bureau of Mines5 indicate that the deaths per thousand 300-day workers have decreased from 9.13 in 114 to 6.14 in 1926, and that the deaths per million tons produced have decreased from 9.18 in 1914 to 4.98 in 1926. Table 1 gives fatality rates in Colorado and in the United States from 1914 to 1926 inclusive. [ ]

Jan 1, 1929

By C. M. McKinney

This report contains Bureau of Mines routine crude-oil analyses of 20 samples from5 areas on the arctic slope of Alaska. Two samples were condensates from the South Barrow gasfield, Barrow Lakes area. The remaining 18 samples were crude oils from the following areas: Barrow Lakes, 1 seepage sample; Umiat, 10 well samples; Cape Simpson, 1 seepage sample and 3 well samples; Fish Creek, 2 well samples; and Wolf Creek, I well sample. Table 1 summarizes information on the origin of the crude-oil samples, and table 2 summarizes characteristics of the samples. Item numbers in both tables correspond to item numbers of the analyses at the end of this report, and the samples are referred to by these numbers throughout the text.

Jan 1, 1959

By Heine Kenworthy

In 1930 the Shenandoah-Dives Mining Co. near Silverton, Colo., put into operation a newly erected, 300-ton selective flotation plant to mill complex ores from its nearby mine. The operation was a steady producer and was enlarged to treat 600 to 800 tons a day. In 1942 the company opened and started milling an area in the mine containing semioxidized ore. The valuable mineral. Content of this ore was considerably higher than in the straight sulfide ore previously handled alone. The mixture of clean sulfide and semi-oxidized ore was difficult to treat; consequently tailing losses, especially with respect to lead, were high. A. few years later, in order to study the possibilities, of obtaining higher recoveries by a modification of the mill flow sheet, a 1,200-pound sample of mill feed, taken over a period of several days by the company, was submitted to the Mississippi Valley Experiment Station for testing. Although this sample proved to contain more than twice as much lead as the average yearly mill feed, the same problem of recovering the oxidized values were present.

Jan 1, 1948

By Oliver Bowles

The United States has never attained importance as a producer of asbestos, the domestic output being only 1 to 3 percent of the quantity required to supply raw material for its extensive asbestos-product manu- facturing industries. Production is centered in four principal countries-- Canada, Rhodesia, Union of South Africa, and the Soviet Union. Since asbestos first became an important commercial commodity the Province of Quebec, Canada, has led in tonnage produced, but a large proportion of the output of this province is shorter, nonspinning grades. Since 1916 the Union of South Africa and Rhodesia have become increasingly important as sources of the higher-grade spinning fibers. Before the World War Russia ranked next to Canada as a producer of asbestos, but during the revolution- ary period the industry in that country was almost at a standstill. In 1926, however, activity was revived, and each year since then production and exports have increased greatly. Minor quantities of asbestos are produced in Cyprus; Australia, Finland, and several other countries. Chrysotile is the leading product in all the producing countries, but substantial quantities of both blue (crocidolite) and brown (amosite) asbestos also are produced in the Union of South Africa. Minor quantities of anthophyllite and similar amphibole varieties are mined in the United States, Italy, Bulgaria, Finland, and several other countries.

Jun 1, 1934

By L. B. Berger, S. J. Pearce

One phase of Bureau of Mines' work in health and safety is promotion of the use of safe, satisfactory, and reliable respiratory protective. devices. To insure that such devices will be available, the Bureau has established schedules of minimum requirements for self-contained breathing apparatus, gas masks, supplied-air respirators. (hose masks, air-line respirators, and abrasive blasting helmets, hoods, or masks), dispersoid (dust, fume, and mist) respirators, and nonemergency gas respirators (chemical cartridge respirators). Approval tests of self-contained breathing apparatus are conducted by the Safety Branch; approval tests of other types of respiratory protective equipment are conducted by the Health Branch. Both branches are in the Health and Safety Division.

Jun 1, 1950

By L. R. Burdick, R. Wiggers, J. F. Berkley

"INTRODUCTION On February 23, 1944, Solid Fuels Administrator Harold L. Ickes stated that the existing fuel shortage made it necessary to utilize a great surplus of freshly mined anthracite ranging in size from Barley (No. 3 Buckwheat) downward through the smaller sizes. As a part of the program to increase the use of such coal, field trials of mixtures of bituminous slack coal and anthracite Barley were made on industrial-size stokers at many fuel-burning plants. The following covers the test information it was possible to accu-mulate during the work of initiating the use of these mixtures at the plants.SUMMARY AND CONCLUSIONSField tests of various mixtures of bituminous slack coal and anthracite Barley on industrial-type stokers show that the use of such mixtures is very practicable and that it is possible to change and usually to adjust to an improved condition the characteristics of a fuel bed of eastern bituminous slack coal by the addition of proper amounts of anthracite. The improved uniformity of the fuel bed of single-retort stokers makes possible less manual attention to the bed. Air flow through the fuel bed is affected.Smoke is decreased. In general, the fly ash and also the unburned combustible in the fly ash and refuse are increased. Clinkering in the fuel bed is generally lessened. The peak-load carrying capacity of the stoker is definitely affected, usually adversely for the higher percentages of anthracite."

May 1, 1946

By Robert K. Koch, Henry E. Blake

Laboratory tests were made to determine if aluminum fluoride of commercial grade could be synthesized by reacting alumina hydrate with dilute ( 25 to 75 grams per liter of fluorine ) aqueous fluoride solutions . • Products containing up to 90 percent aluminum fluoride ( A1F ) were synthesized by reaction of alumina trihydrate ( A120 3H2O) with either dilute hydrofluoric acid ( HF ) or ammonium fluoride ( NHF) solutions , the ammonium fluoride solution resulting from ammonia ( NH ) desilication of a hydrofluoricfluosilicic acid ( HF - H₂ SiF ) solution . Fluorine recoveries of over 80 percent were obtained with either type of solution . The hydrated precipitates of AlF, and ( NH4 ) , A1F ( ammonium aluminum fluoride ) obtained by reacting hydrated alumina with these solutions were subsequently converted to anhydrous AlF, by controlled heating .

Jan 1, 1964

By John E. Kelley

The Bureau of Mines conducted a study to determine the feasibility of joining refractory metal compounds to each other and to oxide ceramics by a vacuum hot press-diffusion bonding method. Very satisfactory joins were made of ZrC to ZrB2, ZrN to ZrB2, ZrC to ZrN, and of ZrC, ZrN, and ZrB2 to Al203. Each of these join assemblies contained a mixture layer comprising 50 weight-percent each of the two end compounds. The mixture layer, sandwiched between each end compound, enhanced bonding and smoothed out the thermal expansion gradient between the two end members. Strength and thermal shock tests showed that the join areas of the ZrC, ZrN, and ZrB2 joins were stronger and more shock resistant than the parent materials. Also included in the joining tests was one each of TiC to TiB2, TiC to TiN, TiB2 to TIN, and TiC to ZrB2 joins. Each of these was well bonded, showing that the vacuum-hot-press method can be used for a variety of systems.

Jan 1, 1969

By Joan K. Kuenzi

The purpose of this U.S. Bureau of Mines information circular (Ie) is to discuss how job analysis methods taken from different disciplines can be used together to form a more complete picture of jobs in the mining industry. "Job analysis" is a term used by many researchers, but use of the term is far from standardized. Authors of papers on this subject often state that there is confusion in how or why jobs are to be analyzed, what the resulting information is to be used for, and what the "job analysis" actually means. The process of breaking a job into elemental tasks and analyzing them is used to determine what skills and knowledge are needed to perform a given job, to improve efficiency, and to develop safer job procedures. All are valid reasons to analyze jobs, but the methods used to accomplish the analyses may be very different. In order to create a more complete picture of a job, it may be useful to incorporate methods and information from different areas of study rather than choosing one method for analysis.

Jan 1, 1995

By Robert L. Jones, Clifford Dunham

"INTRODUCTION The Wah Wah mine was examined 3/ by the Bureau of Mines in September, and a project was started in November 1942. Assistance was given by the Federal Geological Survey in formulating proposals and plans, and two geoloists were assigned to map the surface and underground workings in October 1942.HISTORYThe Pine Grove mining district was organized in 1S73, but no work was done there until it was reorganized in 1879, after which it is reported that a little ore was shipped. The Wah Wah Mining Co. was incorporated September 2, 1937. Prior to that time, predecessor organizations had spent approximately $122,000 on the property now held by this company. The board of directors of the Wah Wah Mining Co. approved expenditure of $47,652.14 from September 1937 to June 1942 for development. This work was confined to the Tasso shaft and connecting levels. Shipments in 1939 amounted to 925.789 dry tons with a gross value of $12,477.83. This ore contained 20,130 pounds lead, 1,390 pounds copper, 7,434 ounces silver, and 65.09 ounces gold. The mine was idle from July 1941 to November 1942, when, the Bureau initiated a project to unwater the Tasso shaft and proceed with the exploratory work as outlined in the War Minerals Report."

Apr 1, 1946

By J. G. Kirby, F. S. LOTT

The mmber of petroleum refineries in the United States decreased during 1949 from 375 to 367 while the total crude-oil charging capacity of refineries continued to increase. A gain in the through-put capacity of 257,305 barrels daily raised the total to a new high level 6,696,300 as of January 1, 1950. The capacity of the average refinery to process crude-oil increased during 1949 from 17,171 barrels daily to 18,246. The four coastal refinery districts accounted for 178,900 barrels or 70 percent of the total capacity increase and the Illinois-Indiana- Kentucky district 57,950 barrels, or 23 percent. Slight declines in capacity were reported in the Texas Inland and the Arkansas-Louisiana Inland districts. The capacity building on January 1, 1950, 145,600 barrels daily, was less than half the amount under construction a year earlier. Most of the new construction involved enlargement of existing refineries and was confined to the East Coast and Indiana-Illinois-Kentucky districts. Two new refineries, however, were under construction, one in Oklahoma and the other in Texas. The shut-down capacity increased for the first time since 1946, and the 473,302 barrels daily reported on January 1, 1950, was the largest recorded since January 1, 1938. The only refining district showing a decline in the shut-down capacity was the Appalachian No. 2 district. The largest increases were reported in the Texas Gulf, Indiana-Illinois- Kentucky, California, and East Coast districts. The operating ratio of the petroleum refining industry, as indicated by dividing the January 1950 runs to stills of 5,483,000 barrels daily by the total installed capacity January 1, 1950, was 81.9 percent, compared with a ratio of 87.8 percent at the beginning of 1949.

Aug 1, 1950

By Robert H. Ridgway

This circular outlines salient facts regarding the manganese-ore industry in the United States and the world. It is founded chiefly upon published information available in the literature of the subject. The Bureau of Mines has in its files additional, more detailed data upon many of the topics presented very briefly here, and will endeavor to assist the mineral industries and public by giving further information in response to individual inquiries. The Bureau will welcome comments, criticisms, and contributions of data that may assist in making later additions of this circular more accurate, or in developing more fully its mineral files pertaining to manganese. In reporting the production of manganese-bearing ores in the United States the following classification has been adopted by the Bureau of Mines: (1) Metallurgical-grade ores, under which have been classified manganese ores containing 35 percent or more of manganese used in the manufacture of iron and steel, ferruginous manganese ore containing 10 to 35 percent of manganese, manganiferous iron ore containing 5 to 10 percent of manganese, and manganiferous zinc residuum; (2) battery ore; (3) fluxing ores, under which are classified ores that may contain a few ounces of silver and are rich enough in manganese to make them valuable chiefly for fluxing purposes in nonferrous smelters; and (4) miscellaneous ores, under which are classified the ores shipped to brick manufacturers, glass makers, and manufacturers of manganese chemicals.

Jan 1, 1933

By W. W. Weller

Low-temperature heat capacities of scandium sesquioxide (Sc203) and a mixture of cerium sesquioxide (Ce203) and cerium dioxide (CeO2) were measured over the temperature range from 50° to 298° K. The entropy of scandium sesquioxide at 298.15° K was evaluated directly as S°298.15 = 18.4 ± 0.1 cal/deg mole. That of cerium sesquioxide was extracted by combining the heat-capacity data for the mixture with those for pure cerium dioxide; the result was S298.15 36.0 ± 1.0 cal/deg mole.

Jan 1, 1963

By X. N. Hu, X. Shi, V. Vallyathan, N. S. Dalai

"Although silicosis has been studied extensively, the mechanism is still not fully under stood. Experiments do provide evidence that the actions of unique properties of silica surface on the cell membrane are the starting point of silicotic processes. This paper summarizes literature on chemical properties of silica surface, and the effect of particle size on silica toxicity. This paper also discusses the ways in which silica dusts are thought to interact with the cell membrane, with emphasis on freshness, hydrogen bonding, and free-radical interactions.INTRODUCTIONSilicosis is a debilitating pulmonary disease that afflicts persons (miners, foundry workers, ceramic workers, heavy construction workers, etc.) who chronically inhale silica-containing dusts (Schepers, 1960; Silicosis and Silicate Disease Committee, 1988). Since silica is second only to oxygen in weight percentage of the earth's crust (about 28%) and is found in an enormous diversity of minerals, it is natural that silicosis is one of the Major industrial health hazards all over the world. Although silicosis has been studied extensively, the mechanism by which the dusts exert their toxic actions on cells and the processes by which these-actions progress to fibrogenesis are still poorly understood. The biological characteristics of the dusts are largely unknown, although it is suggested that the dust size, shape, surface charge, roughness, surface chemical composition, trace metal content, and crystallinity; dose of silica in the ambient air of the workplace; duration of exposure; genetic variation in exposed sub¬jects; personal respiratory patterns; and presence of any coexisting dis¬ease (such as tuberculosis or rheumatoid arthritis) all influence the ex¬pression of silicosis (Koskinen et al., 1983; Noweir et al., 1980; Raask and Schilling, 1980; Reiser and Last, 1979; Thorne et al., 1985; Wolff et al., 1981). The actual biochemical mechanisms through which these factors operate are still unclear. However, the experiments do provide evidence that the actions of certain unique properties of silica surface on the cell membrane are the starting point of the silicotic process (Allison et al., 1966; Allison and Harrow, 1971; Bateman et al., 1982; Marks, 1957; Parazzi et al., 1968; Reiser and Last, 1979; Summerton et al., 1977). This article summarizes literature on chemical properties of silica dusts and how silica dusts are thought to interact with the cell membrane, with emphasis on hydrogen bonding and free-radical interactions."

Jan 1, 1989