Search Documents

By Harry Perry, Mary S. Esfandiary

This is a revision of a directory of coal research organizations throughout the world that was first published in 1961 as Bureau of Mines Information Circular 8008. Because of the wide acceptance of the first edition , a revision which would supply up- to - date information on coal research and which would facilitate communication among organizations of similar interest seemed important . This compilation includes the names and activities of organizations of various types -government , university , private , and industry . The areas of investigation that each organization is engaged in are indicated in broad terms : Analysis and constitution , mining and geology , preparation , briquetting , combustion , high- and low-temperature carbonization , gasification , conversion to solid and liquid fuels , and health and safety . Publications issued by and describing the work of each organization are cited ; almost all of the organizations also publish results of their investigations in the technical press . Selected technical and trade publications that publish information on the science and technology of coal and are not published directly by any of the organizations listed are cited in the pages following the list of organizations in each country . Information that would improve coverage and accuracy of the next revision of the publication will be welcomed by the Bureau of Mines .

Jan 1, 1966

By Jeffrey Shawn Peterson

Among underground coal miners, hearing loss remains one of the most common occupational illnesses. In response, the National Institute for Occupational Safety and Health (NIOSH) conducts research to reduce the noise emission of various underground coal mining equipment, an example of which is a roof bolting machine (RBM). After the removal of coal or rock, the remaining strata may be subject to fall, either from overhead (the roof) or from the side (the rib). One method used in underground coal-mines to prevent failures requires the installation of roof bolts. The roof bolting machine operator trams the machine to the required location, drills a hole into the strata, and then installs a roof bolt, supporting the roof or the rib, as the case may be. Field studies support the premise that, on average, drilling noise is the loudest noise that a roof bolting machine operator would be exposed to and contributes significantly to the operators? noise exposure. NIOSH has determined that the drill steel radiates a significant amount of noise during drilling. NIOSH is developing bit and chuck isolators to reduce vibration, and thus noise radiation of the drill steel, with the longer-term goal of reducing roof bolting machine operator noise exposure. Laboratory testing has shown that operator ear sound pressure levels may be reduced by 3 to 7 dB(A), depending upon the test configuration and drilling media.

Jan 1, 2009

By BUREAU OF MINES

A complete list of permissible mining equipment, rescue apparatus and gas masks tested prior to July 1, 1928, was published in Bureau of Mines Information Circular 60772. The present list includes practically all equipment tested and, approved by the Bureau, up to and including Jan. 1, 1929. It covers electric air compressors, coal drills, mining machines, loading machines, conveyors, mine pumps, room hoists, mine telephones, rock-dusting machines, switches, electric cap lamps, flame safety lamps, electric hand and trip lamps, flash lamps, methane indicators and detectors, blasting units, storage barrery locomotives, tandem locomotives, power trucks, concrete mixers, self-contained oxygen breathing apparatus and gas masks. The system under which those devices were tested permits the manufacturer, after his equipment has passed certain tests prescribed by the Bureau of Mines, to mark his equipment with a seal shoring that it has been "approved" by the Bureau. These tests are designed to insure that the equipment has the minimum requirements for safety in use. The only object of the Bureau in making such tests and pub- lishing lists of permissible equirment is to safeguard the lives of workers and to help lesson the hazards of mining.

Jan 1, 1929

By Peter N. Gabby

A mineral purvey of 40,000 acres of the 42,213-acre Little Humboldt River Wilderness Study Area was conducted by the U.S. Bureau of Mines in 1985 at the request of the U.S. Bureau of Land Management. There are no identified mineral resources but anomalous gold, silver, mercury, and arsenic concentrations were found. The study area is located in Elko County, NV, in the Owyhee Upland geomorphic subprovince. It is underlain by mid- to late-Miocene-age rhyolite, basalt, tuff, vitric ash, and tuffaceous siltstone. On the south side and partly within the study area, a mining company recently (January 1986) located 125 contiguous claims over an area of hydrothermally-altered volcanic rocks that have anomalous surface concentrations of gold, mercury, arsenic, and silver. Anomalous gold-silver concentrations in altered rocks were encountered at several other widely scattered localities in the study area. These elevated metal concentrations and associated hydrothermal alteration indicate gold resources may be present in the study area. A 20-ft-thick bed of diatomaceous earth, which contains 60 to 85 percent diatoms, crops out 0.3 mi north of the study area. Elsewhere, three samples of altered volcanic tuff taken within the study area contain from 46 to 70 percent zeolite (clinoptilolite). The diatomaceous earth and zeolite sampled are not of sufficient quality to compete with materials presently being marketed. There has been no mineral production from the study area, but a caved adit, about 25 ft long, and six prospect pits were found.

Jan 1, 1987

By A. Gene Collins

Some of the geochemical relationships that exist between subsurface fluids and the associated geologic strata in petroleum producing areas of Louisiana have been determined. Samples of petroleum-associated water were obtained from 126 wells in Louisiana that produced from sediments of three geologic ages: Tertiary, Cretaceous, and Jurassic. The samples were trans-ported to a central laboratory for analysis of chemical composition, using standard methods, to determine if the compositions varied with the geologic strata of their source and, if so, why. The dissolved constituents were com-pared with those of a brine that was concentrated by evaporation. The concentrations of bromide, calcium, and strontium were useful in distinguishing the brines produced from sediments of a late age from those of an earlier age. The concentration ratios of Mg' (total equivalent magnesium) and bromide indicated that dolomitization probably had occurred and altered the composition of the brines. A principal-components analysis of the data indicated an inverse relationship between depth and concentrations of bromide, strontium, calcium, and lithium.

Jan 1, 1970

By J. S. Tosh

The Federal Bureau of Mines has investigated the equilibrium of the system potassium carbonate (K2C03) potassium bicarbonate (KHCO3) potassium bisulfide (KHS) carbon dioxide (C02) hydrogen sulfide (H2S) water (H20). Partial pressures of hydrogen sulfide, carbon dioxide, and water vapor were measured at 70° to 130° C. over solutions of 20-, 30-, and 40-percent-equivalent potassium carbonate containing from 20 to 3,000 grains of equivalent hydrogen sulfide per gallon of solution. This study was made to obtain equilibrium data for evaluating the feasibility of using solutions of hot potassium carbonate for removing, hydrogen sulfide from gas mixtures. The equilibrium partial pressure of hydrogen sulfide may be correlated with the ratio of the molal concentrations of the solutes (KHC03) (KHS)/ (K2CO3). The relationship is shown graphically for the 30- and 40-percent solutions. Once this ratio is determined, the partial pressure of hydrogen sulfide can be obtained from the curves. The equilibrium data show that effective removal of both carbon dioxide and hydrogen sulfide can be achieved simultaneously with hot solutions of potassium carbonate.

Jan 1, 1960

By Van E. Shaw

Bastnaesite is a natural rare-earth fluorcarbonate of the cerium group that affords an abundant and high-grade source of the lighter rare-earth elements. A simple and efficient method has been developed by the Bureau of Mines for extracting rare-earth compounds from this mineral. Digesting of a flotation concentrate with sulfuric acid converts the rare-earth compounds from fluorcarbonates to sulfates. Action of the acid releases gaseous com-pounds of fluorine and silicon, leaving the sulfated material free of these elements; carbon dioxide from carbonate decomposition is eliminated at the same time. Calcining the sulfated material at 1,200° F. renders the gangue constituents insoluble, whereas the rare-earth sulfates are left in water-soluble form. Leaching with water yields a solution of pure rare-earth sulfates. Bastnaesite could become prominent as a source of cerium-group rare-earth elements. It is rich in the light rare-earth elements and comparatively easy to process; reserves of the mineral are extensive enough to supply a greatly expanded market for many years.

Jan 1, 1959

By Steven J. Page, John A. Organiscak

Prolonged exposure to airborne respirable coal mine dust is responsible for coal workers' pneumoconi¬osis (CWP): Furthermore, miners who show evidence of higher radiographic categories of simple CWP are at increased risk of developing progressive massive fibro¬sis (PMF). As of 1990, there were nearly 130,000 coal miners in the United States. "' This excludes mines that produce less than 10,000 tons annually and the anthracite coal mines. Estimates indicate that at age 58, an average of 7/1000 U.S. workers and 89/1000 U.K workers will have developed PMF(2-1) Health research studies have iden¬tified that the risk of developing and the severity of CWP arc directly related to (1) the amount of respirable dust exposure and (2) the coal rank.,'- The rank of coal is its stage of formation in the series peat, lignite, sub-bituminous, bituminous, and anthra¬cite (in order of increasing rank). The rank of coal can also be represented by the com¬mercially important characteristics specified by its proximate analysis: fixed carbon, vol¬atile matter, mineral matter, and moisture content.

By D. J. Bauer

Solvent extraction techniques were used to determine the extraction sequence of yttrium and the rare-earth elements in an amine solvent extraction system. Single-stage extraction with Primene 81-R resulted in separation factors of 3.8 between yttrium and dysprosium and 25 between yttrium and cerium. Yttrium was concentrated in the aqueous phase. EDTA and DTPA, as aqueous phase counterextractants, enhance separation factors in mine-rare-earth sulfate systems. Yttrium separation from heavy rare-earth elements exhibits marked sensitivity to the position of yttrium in the selectivity scale of the rare-earth elements with the sequestrants. Yttrium-ytterbium separation is more effective with EDTA, whereas yttrium-dysprosium separation is more effectively increased with DTPA.

Jan 1, 1963

By Harry D. Jumper

This paper describing the methods of ruining a sand, gravel, and bowlder deposit 20 miles east of Los Angeles, and the classification and preparation of these materials for market, is one of a series being prepared for and published by the United States Bureau of Mines on methods and cost of mining sand and gravel. These papers are designed to disseminate technical information regarding, the methods used. The cost tabulations represent operating expenditures only and not total costs. It is recognized that publication of total costs might in many instances cause embarrassment to individual operators as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion anti study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations stall ensue. The description contained herein is typical of this industry in Southern California. ACKNOWLEDGMENT The author acknowledges tine assistance of L. L. Rogers, vice-president and manager of production and distribution for the Consolidated Rock Products Co., in the preparation of this paper.

Jan 1, 1933

By H. C. Loesche

The problem of signaling to the hoisting engineer from the cage in a shaft mine has been given considerable thought and attention by engineers and mine operators seeking to Increase the safety and efficiency of hoisting. HISTORY R. L. Rutherford,3/ an employee of the Magma Copper Co., Superior Ariz., realizing the need for a simple and practical moving-cage signaling system, began a serious of experiments early in 1937, Available electrical moving-cage signal in operation at this date required that signal wires be installed in the shaft to make a simple, positive signal without wires, the first experiments used the pipe lines in the shaft for carrying the signal current, but these experiments were not successful.

Jan 1, 1945

By R. V. Ramani, C. B. Manula, A. Owili-Eger

This report was prepared by The Pennsylvania State University under USBM Contract No. G0111808. The contract was initiated under the Coal Mine Health and Safety Program. It was administered under the technical direction of DMRC, with Mr. G. R. Schottler acting as the technical project officer. Mr. J. A. Herickes was the contract administrator for the Bureau of Mines. These applications were developed initially as a part of the instructional material for the course Mng 422, "Mine Ventilation and Air Conditioning" at the Department of Mineral Engineering, The Pennsylvania State University. This ventilation simulator was developed under contract from the Department of Environmental Resources, formerly the Department of Mines and Mineral Industries, Commonwealth of Pennsylvania.

Jan 1, 1975

This is the final report on Project CR-102 under the auspices of the Department of Environmental Resources, Commonwealth of Pennsylvania .1 The project was activated on January 5, 1970, with financial support from Bituminous Coal Research, Inc., the Pennsylvania Coal Research Board, and the Water Quality Office of the Environmental Protection Agency (WQO-EPA)2 through Grant 14010 EST to the Commonwealth of Pennsylvania Work on the project was conducted according to the procedures outlined in BCR Research Program Proposal RPP-164R, dated April 24, 1969, and a subsequent Revulsion of Scope, dated February 25, 1970. This report covers the entire project period from January 5, 1970, through March 25, 1971.

Jan 1, 1971

By Gordon L. Kinney

The only economically important mineral currently produced in Bangladesh was natural gas. Bangladesh was not a world? ranked producer of any mineral commodity, but the possibility of producing and exporting commercial amounts of liquefied natural gas (LNG) was being examined. Proved reserves of natural gas were sufficient to supply most of the country's industrial and domestic heating and electric needs and still support an export-oriented LNG plant. Other mineral production was of virtually no significance to the economy, although there were a few prospects for nonmetallic mineral development. Bangladesh continued to make economic progress during 1978 and into early 1979. Gross domestic product (GDP) at current prices rose from $6.6 billion in 1976-772 to $8.2 billion in 1977?78 and $9.3 billion in 1978.79.2 In fiscal 1979, the economic conditions were favorable until a severe drought hit most of the country. It W88 reported that conditions were the worst in 40 years, and 88 of July 1979, substantial crop losses were predicted. The agricultural sector accounts for over 53% of the GDP and about 75% of all employment. The poor weather will cause economic problems in the form of slower growth, larger trade deficits, and a higher rate of inflation. The 1978.79 statistics showed that real GDP increased just 4%.

Jan 1, 1981

In 2004, a total of 4,401 stone mining operations reported employment to the Mine Safety and Health Administration (MSHA). Stone mines comprised 30.4% of all mining operations.

Sep 1, 2007

"The main objective of this research is to identify the mechanisms of control of respirable dust generation in coal mines. Full understanding of the mechanics of crack propagation in coal is of fundamental importance in studies of the generation and control of respirable dust.The main objectives of this fracture investigation are: 1) to determine reliable data on the fracture toughness of coal as a parameter controlling unstable crack propagation; 2) to determine fracture propagation velocity in coal providing data on the terminal velocity at which crack bifurcation occurs and fine fragments of coal material are generated; and 3) to apply the critical strain energy density criterion to model mixed mode crack propagation in coal.The development of the protocol, laboratory procedure and equipment necessary to conduct an extensive mixed mode fracture toughness testing program has been completed. About 80 mixed mode fracture toughness tests, 10 good fracture velocity records and over 50 fracture surface examination with the SME are available. The details of the mixed mode fracture toughness testing are available in a paper titled, ""Development of Mixed Mode Testing System for Geologic Materials"" which is available from the center. The average fracture toughness and critical strain energy density values for the three seams investigated to date are included in the attached Figures 71, 72, 73."

Nov 1, 1988

This NIOSH Toolbox Training program contains 52 different modules designed to stimulate safety discussions among your employees. Each module is intended to be completed in roughly 10 or 15 minutes, so a Toolbox Training session can be conducted once a week for the entire year. Each session counts toward your employee’s 8-hour annual MSHA refresher training, thus saving an entire day of work.. The modules are used to refresh employees on the procedures, policies, and practices of working safely at a specific mine site and can easily be tailored to fit conditions and situations found on your property. Every module follows the same format, so that as the weeks pass, miners will start to approach every safety situation in the same way. A typical Toolbox Training session contains five basic steps that cover all the information in the module. 1. Identification of the hazard and discussions about the types of injuries typically associated with the hazard. 2. Discussions of some of the causes of the hazard. The MSHA example included with each module should be referenced. 3. After the hazard and accident has been explained and understood, discussions about best practices and tips for avoiding a similar accident. 4. Review of similar conditions or near misses from your mine site using the leading questions on the form to start a discussion. Specific examples of equipment or structures on the site that could lead to the same accident should be discussed. The blank space on the module is used to add your own remarks and questions to supplement the given information. 5. Miners fill out the training record on the back of the form with name, initials, and date of training session. The modules are designed to be kept in a standard three-ring binder and easily photocopied. This way, the same set of modules can be used for years to come. A blank form is included that can be used to create more Toolbox Training modules. The key component of Toolbox Training is to start a discussion among employees that will allow them to see the hazards around them every day and respond to these hazards in a safe and consistent manner. To start a discussion, ask questions that need more than a one-word response. Get the miners to talk about similar situations from their own experiences and give suggestions about how to fix the hazards around them. Toolbox Training is a quick and effective way to cover specific mining hazards, but it only works if miners are involved in the discussion.

Jan 1, 2004

By R. L. King, J. Cervik, A. A. Campoli

The Bureau of Mines performed laboratory experiments to evaluate the triboelectric effect of particulate-laden gas streams on polyethylene pipe at various velocity, humidity, dust-size, and dust-load conditions. Charges in excess of 10 kV were produced on the outside and inside surfaces of laboratory pipe samples, when exposed to 40 pct relative humidity (RH) gas stream containing coal dust. However, no charges were produced in laboratory tests that duplicated the over 75 pct RH and dust-free gas streams found in working underground pipelines. Bare cop- per wire, which is wound around the polyethylene pipe in a 1-ft (31-cm) spacing and grounded, eliminated the charge on the outside surface of the pipe, but not on the inside of the pipe surface,

Jan 1, 1986

The question of earth models has repeatedly arisen in our work. An accurate representation of the seismic properties is required for three reasons: 1.To be able to determine from a set of received arrival times, the location of a seismic source in the earth, and secondly the degree of accuracy required in the model used for calculating source location from the set of arrival time differences. 2. To be able to determine the expected arrival times at an array of geophones produced in response to a hypothetical source in the earth. 3. To be able to estimate received signal strengths more accurately. The work reported here on earth models is based on information from sever- al consultants and from others who expressed an interest in the problem and supplied information to us. II. COAL MINE GEOLOGY On one of our earlier assignments for the Bureau of Mines, Earth Science Research Inc. of Cambridge, Massachusetts prepared for us a short description of the lithology to be expected at coal mine sites. This description follows, together with the ranges of compressional seismic velocities (Figure I*) associated with typical materials comprising the layered structure of a coal mine area. Coal is primarily associated with fresh water sediments including sandstones, shales, and clays, and occasionally may be metamorphased to varying degrees. In the Appalachian Basin the coal beds occur within cyclical sequences of non-marine shales, sands tones, conglomerates, limes tones, and clays. The beds range in thickness from a few inches to 60 feet, averaging between 2 feet and 10 feet. They have generally broad areal extent, occasionally up to 5,000 square miles, and have an overall tabular or lens-like shape. Within a particular lens, local changes in thickness are normal.

Jan 1, 1974

By L. R. Burdick

The Smokescope is an instrument recently developed for determining the density of smoke by shade comparison. The instrument is designed so that the smoke is seen adjacent to two shades of gray corresponding to Nos. 2 and 3 on the Ringelmann chart. Data on smoke density are important in the smoke-abatement field. The method that is specified and accepted as standard for smoke-density determination by the majority of city smoke regulations involves comparing the smoke shade with the four shades on the Ringelmann chart as published by the Bureau of Mines.2/ This investigation was made to determine the accuracy and convenience of the Smokescope. It was conducted as a part of the Bureau I s air-pollution work, which includes the study of techniques that will promote smoke abatement. The accuracy of the Smokescope was arbitrarily defined as the difference between the Smokescope determinations and the determinations by the accepted, standard method and was expressed as Smokescope correction. Although the corrections obtained were strictly correct only for the two observers and the Smokescope of the investigation, they indicate what might be expected from any observer who uses a Smokescope with reference shades that duplicate those of the test instrument. The report is devoted largely to the data on Smokescope correction, which were taken from a single stack under controlled smoke conditions. Field work, which was done at various locations with different stacks, is mentioned briefly in connection with the comparison of the convenience of the two methods. The data for estimating Smokescope correction were taken for the three variables that were expected to affect the results, namely, the density of the smoke, the amount of light, and the color of the sky behind the smoke.

Jan 1, 1955