Search Documents

By E. E. Maillot

In 1943, diamond drilling by the Bureau of Mines, comprising 11 holes which totaled 1,295.6 feet, showed that the pegmatite at Black Mountain consisted of shallow lenses in interbedded biotite-quartz-schist and impure quartzite. The average thickness of the pegmatite was 9.7 feet. Mineralization had a zonal arrangement. Beryl was most abundant near the footwall contact of the pegmatite. The average estimated beryl content of the pegmatite exposed at the surface was 0.81 percent, and the highest content of any pegmatite area was 1.75 percent. Other economic minerals were scrap mica, feldspar, spodumene, and lepidolite. Representative samples of the Black Mountain deposit failed to yield high-grade boryl concentrates by straight flotation owing to the presence of considerable spodumene. By employing heavy medium separation to remove the spodumene, 75.4 percent of the. BeO wan recovered in a flotation concentrate assaying 10.4 percent BeO.

Jan 1, 1949

By Richard A. Winters

The 31,880-acre Battle Creek Wilderness Study Area (WSA) was evaluated for mineral resources by the U.S. Bureau of Mines in 1984. No mining district is in the area, nor were any mines or claims recorded or found. Oil and gas leases, or lease applications, covered about half the area in early 1984. No known exploration has occurred. The entire WSA is covered with thick volcanic flows. Faults in these volcanic rocks may have provided conduits for mineralizing solutions emanating from the basement rocks; however, no evidence of mineral deposits was detected from rock samples collected along the faults. Reconnaissance samples from sand and gravel deposits yielded gold at less than $0.02/yd3. The source of the gold is assumed to be intrusive rocks or the Challis Volcanics about 20 miles north of the study area near the headwaters of Battle Creek. No economic concentrations of minerals were found in the WSA. INTRODUCTION Mineral surveys of designated wilderness study areas (WSAs) 1/ are conducted by the U.S. Bureau of Mines (USBM) and the U.S. Geological Survey (USGS) at the request of the U.S. Bureau of Land Management (BLM). The USBM researches the mining and mineral exploration history and evaluates mines, prospects, and mineralized areas within or adjacent to WSAs. The USGS studies WSAs by regional geochemical and geophysical surveys and geological mapping. The USBM and the USGS investigations are summarized in a joint report used to help determine the suitability of WSAs for inclusion into the National Wilderness Preservation System. Although the immediate goal of this USBM study is to provide data for the President, Congress, BLM, and the general public for land-use decisions, the long-term objective is to help insure that the Nation has an adequate and dependable supply of minerals at reasonable cost.

Jan 1, 1985

By A. S. Prokopovitsh

A spectrophotometric method for the determination of small amounts of copper in tungsten metal powder using the principle of solvent extraction has been developed by the Federal Bureau of Mines. The metallic sample is dissolved in hydrogen peroxide, tartaric acid added, the pH adjusted, and the excess peroxide destroyed by boiling. Copper is reduced to the cuprous state, and the reagent neocuproine (2,9-dimethy1-1,10-phenanthroline) is added to form a colored complex with the copper. This colored complex is then extracted into chloroform and the absorbance of the separated chloroform layer measured on a spectrophotometer. Copper contents as low as 1 p.p.m. (parts per million) can be determined. The method is limited to finely divided tungsten powder. The interest of the Bureau of Mines in developing more sensitive methods for the determination of trace impurities in high-purity tungsten prompted an investigation of the possibility of using solvent extraction-colorimetric methods. The organic reagents now commercially available make possible many extremely sensitive colorimetric methods for the determination of metallic ions. Extraction of the colored complex into a small volume of organic phase can be used to further increase sensitivity (4) .4/ This general approach has the added advantage that no special equipment beyond that normally found in an analytical laboratory is required.

Jan 1, 1961

By S. Ralph Austin

This Bureau of Mines investigation determined the effects of so-called annealing at high temperatures on radon-222 emanation from domestic uranium ores. Concurrently, a method was developed for closely estimating the emanation coefficients of hot samples from measurements of their gamma activity after cooling. Emanation coefficients of 102 samples from 14 domestic areas of past, present, and possible future uranium production were investigated using modifications of the closed-can, gamma-only assay method at and after cooling from 100° to 1,000° C. True annealing probably does not occur below 500° C. In limited investigations at 500° C and above, effects of annealing are masked by the effects of other parameters. Emanation is commonly less at one or more of the steps investigated in the 100° to 500° C range than before heating. This decrease is tentatively attributed to water loss at temperatures dependent upon the minerals present. The average sample emanates least at 300° C; emanation increases with higher temperatures to at least 900° C. Emanation decreases sharply on cooling, but it is partially restored by prolonged exposure to the atmosphere at room temperature. Higher than average emanation of coffinite ores at 500° C and above may be related to destruction of the coffinite crystal structure.

Jan 1, 1979

By G. St John Perrott

"The United States Bureau of Mines is cooperating with the State of Utah and the City of Salt Lake in an investigation of methods of abating the smoke nuisance in Salt Lake City. In the course of this work samples of the atmosphere have been collected and analyzed in an attempt to determine the part played by sulphur dioxide or smelter gases in polluting the air at Salt Lake City.A fairly wide-spread opinion exists in Salt Lake City that the smelters contribute appreciably to the smoke nuisance. The gases discharged from the smelter stacks are believed (1) to float over the city in a heavy blanket which prevents the smoke from rising, and (2) to unite with the water vapor in the air to form corrosive fogs injurious to health and property.The first of these theories seems untenable. If the gas did not mix with air it would sink, owing to its heavier specific gravity, and form a blanket an the earth. Actually, the gas diffuses rapidly in air and any part reaching Salt Take must he thoroughly diluted. Perhaps sulphur dioxide in sufficient concentration might aid in fog formation. The more obvious nuisance, however, would be the injury to health and vegetation.The Garfield smelter is 16 miles west of the city, The Murray smelter 8 miles south, and the Midvale smelter 12 miles south. Under normal operating conditions, a relatively small amount of solid matter is discharged from these stacks. The toxic gaseous constituent of the discharge is sulphur dioxide, it is being discharged from the smelters the year round. If they are a factor in the city's smoke problem, the concentration of this gas in the air of the city should be appreciable and should increase toward the smelters, the con centration being highest with a south or a west wind."

May 1, 1920

By H. B. Brunot

A complete list of permissible mine equipment, tested and approved by the Bureau of Mines previous to January 1, 1947, was published as Information Circular 7432.2/ A list of permissible mine equipment tested and approved by the Bureau of Mines during the calendar years 1947, 1948, and 1949 was published as Information Circular 7569. The present list supplements Information Circulars 7432 and 7569 and includes all of 'the equipment approved during the calendar year 1950. Information Circular 7465, which included a list of permissible mine equipment tested and approved by the Bureau of Mines during the calendar year 1947 therefore is superseded.

Jan 1, 1951

By N. S. Dalal, X. Shi

"With a view of elucidating the role of glutathione (GSH) in the biochemical pathways of the chromate-exposure related carcinogenesis, we carried out electron spin resonance (ESR) spectroscopic investigations of the chromate-GSH redox reactions. The ESR measurements, employing spin-traps, provide evidence for the involvement of the glutathione (GS•) radical, as well as an isolable Cr(V)-glutathione intermediate. These results indicater a new mechanism for the reduction of chromate by GSH in cellular environment and help understand the (unexpected increase in Cr(VI)-induced DNA strand breaks at elevated GSH levels.We report here indirect electron spin resonance (EGR evidence for the involvement of the glutathionyl (GS) radical and direct evidence for a Cr(V) intermediate in the reactions of glutathione ¬(GSH) with chromate for the first time.. This work was undertaken to clarify the biochemical pathway of the reduction of chromate by GSH, since this reduction process is thought to be a critical step in the pathogenesis of the chromate-exposure related carcinogenesis. This follows from the literature reports which show that (a) Cr(VI)compounds have been proven to be carcinogens in laboratory animals as well as in human studies2-4, (b) Cr(VI) and not Cr(III) compounds are mutagenic 5-7, (c) Cr(VI) and not Cr(III) compounds can penetrate cell membranes 8.9 (d) the final state of Cr(VI) in cellular reductions is Cr(III)', (e) by itself chromate (or Cr(VI)) cannot be directly mutagenic since Cr(VI) is known not to interact with isolated DNA under physiological conditions 10, suggesting the significance of Cr(VI).reduction processes. One of the major reductants in cellular environments is thought to be the GSH, both outside and inside the ce11s 11-13. Other evidence for the role of GSH in the chromate toxicity is seen from recent studies showing that exposure of hamster cells to non-toxic levels of added selenite increases the levels' of GSH as well as the Cr(VI)-induced DNA strand beaks 14, and thatsuch DNA strand breaks in hepatocytes also change in direct proportion to their GSH content 15,16. These observations wereinterpreted as implying that the reduction of chromate by GSH, to some reactive intermediate is an important step in the chromatecarcinogenicity 15,16. The following reaction steps were,suggested 15, 16"

Jan 1, 1988

By Donald O. Capstick

A mineral survey of the 520-acre Quigg West Wilderness Study Area (MT-074-155) was conducted by the U.S. Bureau of Mines in 1986 at the request of the U.S. Bureau of Land Management in order to evaluate its identified mineral resources. The Wilderness Study Area is in Granite County in western Montana about 16 miles northwest of Phillipsburg and 27 mi les northeast of Hamilton, MT. Stony Mountain, a study area on lands administered by the U.S. Forest Service, is about 1 mile to the south-southwest and was studied concurrently. No mineral resources were identified in the Quigg West Wilderness Study Area, but high grade gold assays, as much as 1.24 ounce gold per ton, were obtained at the one prospect found. Samples from four workings contained significant gold; minor silver, molybdenum, and copper were also present. The prospect containing the narrow and discontinuous gold-bearing quartz vein straddles the south boundary of the Wilderness Study Area. The shear zone containing the vein projects toward the old Crescent mine, about 4.5 miles to the south, which shows a similar geologic structure.

Jan 1, 1987

By Wallace W. Roepke

The Bureau of Mines has a well-established health and safety research effort directed to fundamental studies of the mine cutting system. This report describes the ignition danger of using cutting bits with flat wear area on still-intact carbide inserts.

Jan 1, 1983

By Chas. G. Maier

The bright annealing of copper is an industrial practice of considerable importance. In connection with this process, equilibrium concentrations of carbon monoxide and dioxide, which may exist in contact with copper and cuprous oxide at elevated temperatures, are of interest. Data obtained at the Pacific Experiment Station of the U. S. Bureau of Mines enable estimates of these equilibrium concentrations to be made in two independent ways. Although the publication of final data on one method can not take place until certain further experimental work is accomplished, repeated requests which the Bureau of Minus has had for data relative to the annealing and deoxidation of copper justify the present preliminary report. This paper deals with the calculation of gas concentrations in the reduction of cuprous oxide, using more scientific data which will be published later, and refers especially to those conditions of temperature and concentration of practical implication, and from which critical limits ensue.

Jan 1, 1929

By James A. West

The South Asian countries of India, Pakistan, Afghanistan, Ceylon, Nepal, Bhutan, and Sikkim arc to varying-degrees just beginning to achieve significant economic and industrial development. These countries are richly endowed with certain mineral resources, and development of these resources is being accelerated. In 1965, the mineral industry remained a relatively small sector of the region's economy, accounting for only about 1 percent of its estimated gross national product of $62,528 million. Nevertheless, the estimated $630 million total value of minerals produced in South Asia during 1965 represented an increase of nearly 15 percent t over that of 1964. India continued as the dominant mineral producer of the region, accounting for 85 percent of the total value of all minerals produced ill 1965. India increased its output of iron ore, manganese, mica, coal, and petroleum. Pakistan accounted for 13 percent of the value of the region's output and recorded increased output of iron ore, chromite, coal, natural gas, and most other minerals. The small mineral industry of Ceylon attained remarkable growth in the production of ilmenite, graphite, and gem stones. The mineral industry of Afghanistan remained relatively insignificant, although development of large known resources of natural gas was continued, Nepal, Bhutan, and Sikkim produced no commercially significant quantities of minerals in 1965.

Jan 1, 1967

By I. O. Salyer

This research was conducted with the objective of suppressing the respirable dust in coal mines by foam application. A formulation was developed for making a water-based, high-expansion, and limited stability foam. A horizontal boring machine was used as a laboratory coal mining model for generating coal dust. A modified laboratory foam generator was built. Foam was applied directly to the point at which dust was being formed by the cutter of the boring machine working against a block of coal. Coal dust was sampled with an impinger and analyzed for the particle count and particle size distribution. Coal dust suppression test results on freshly generated dust have demonstrated very clearly that in laboratory scale experiments over 90% of the respirable coal dust can be suppressed by foam. These tests were run when initial coal du t concentrations were 10 and 70 million particles per cubic foot (mppcf).

Jan 1, 1970

By W. A. McKinney

A sample of oxidized copper ore from a large deposit located in Pinal County, Ariz., about 50 miles northeast of Tucson, was treated by the Federal Bureau of Mines in a small-scale continuous pilot plant by a procedure which comprised acid curing complemented by water leaching and countercurrent decantation washing in a series of drag classifiers. A feed was prepared by pugging minus 1/4-in, ore with concentrated sulfuric acid and about 10 pct, of eater, followed by curing in batches for about 24 hr. The cured ore was fed continuously to a leach drum, where it was mixed with advance solution from the countercurrent washing system to dissolve the sulfated copper. The pulp was thickened and washed in four Esperanza-type classifiers, using a flocculating agent to obtain rapid settling and thickening. The leached ore pulps thickened satisfactorily in the drag classifiers when about 0.8 lb. of a polyacrylamide flocculant per ton of dry feed was used. Clear overflow liquors were obtained, and classifier rake products containing about 60 pct. solids were produced, As much as 90 lb./hr. of ore was treated in the plant, with a recovery of 60 pct. of the total copper or 80 pct, of the acid-soluble copper when 2 tons of water per ton of feed was used in washing. The acid consumption was 4.3 lb./lb. of copper recovered. On the basis of the maximum feed rate employed and the effective pulp-settling area of the classifiers, a total of 1 sq. ft. of pool area was required per ton of dry feed per day for the thickening and washing operations. The washing efficiency in the test was 95 pct.

Jan 1, 1960

By J. M. Singer

The objective of this investigation was to determine minimum air velocities and entrainment rates for coal and rock dust dispersion in wind tunnel experiments under conditions that simulate dispersion from surfaces in coal mines where airflows are induced by weak gas explosions. Dust deposits were bed-or ridge-shaped; particle sizes were 6 to 80 microns (cohesive deposits) or 100 to 150 microns (free-flowing deposits); and wind tunnels were 7.62 cm wide by 5.08 cm high by 300 cm long, and 2.4 m wide by 1.5 m high by 215 m long. The investigation showed that minimum air velocities (directed at mid-height) of separate, layered, or mixed piles of coal dust and rock dust were within the range 5 to 30 m/sec, independent of size of wind tunnel. This finding considerably facilitates scaling of data to mine-size passageways. Free-flowing deposits dispersed relatively slowly by single-particle detachment; cohesive dusts dispersed faster by the breaking and lifting of large clumps along weak failure flames; particle dispersion occurred in flight. Layered or mixed deposits of coal and rock dust did not disperse selectively. Semiempirical expressions were derived relating minimum air velocities and dispersion rates to dust-pile geometry, cohesion, porosity, and bulk density.

Jan 1, 1972

By B. H. Eccleston

Experimental data were obtained from two medium-duty diesel engines derated to qualify for use in underground mines. Gaseous and particulate emissions from these engines were measured and results provide information on the effect of exhaust treatment devices on the emissions. The devices in the study were a catalyst, a particulate trap, and an exhaust gas cooler of the water scrubber type. Emission levels of carbon monoxide and hydrocarbons were observed to be very low in comparison with emission levels of comparable engines in full-rated operation. Oxides of nitrogen and benzo(a)pyrene content of the exhaust also were found to be somewhat low in comparison with previous findings. For particulate reduction, the combination of a particulate trap and a scrubber was observed to be the most effective combination tried; in some cases, over 60 pct particulate reduction was effected by the trap-scrubber combination.

Jan 1, 1981

By J. J. Forbes

The Coal Mine Inspection Branch of the Health and Safety Division, Bureau of Mines, was established to carry out the provisions in Public Law 49, 77th Congress, H. R. 2082, approved May 7, 1941. The series of major disasters that beset the coal-mining industry in 1940 aroused public interest in mine-safety measures, and the act 18 the direct result of this rekindled interest. Under the provisions of the act, the Secretary of the Interior, acting through the Federal Bureau of Mines, is authorized and empowered to make, or cause to be made, annual or necessary inspections and investigations in coal mines, the products of which regularly enter commerce or the operations of which substantially affect commerce. The principal functions of the Federal coal-mine inspectors are to determine the causes of accidents and occupational diseases in coal mines and then endeavor to eliminate or ameliorate them (1) by revealing, through personal conferences with mine personnel, correspondence, and published reports, the unhealthful and unsafe conditions and practices existing in the mines and (2) by recommending practical means for correcting the conditions observed. The act does not provide any enforcement powers, and therefore compliance with the inspectors' recommendations is not mandatory; it does give Federal coal-mine inspectors the right to enter coal mines for inspection purposes.

Jan 1, 1951

Lower workers' dust exposures during bag stacking while ergonomically improving the bag stacking process. Approach Install a new pallet loading dust control system which uses a push-pull ventilation technique along with a hydraulic lift table to control the pallet loading height throughout the entire loading cycle. How It Works A low-volume, high-velocity blower system operating at approximately at 120 cfm blows a stream of air over the top layer of bags on the pallet. The blower system is composed of two 3-inch air jets (approximately 1,200-ft/min velocity) directed toward an exhaust system on the opposite side of the pallet. As these air jets travel across the pallet, they en-train dust generated during bag stacking. The dust laden air is then captured by the exhaust ventilation system which draws approximately 2,500 cfm through an exhaust hood on the opposite side of the pallet.

Jan 1, 1989

By T. L. Joseph

The purpose of this article is to describe briefly the operation of a 6-ton blast furnace on a charge of bauxite, limestone, iron ore, and cast-iron turnings and to point out the bearing which smelting such a charge has upon the production of alumina cement. One object of the experiment, conducted by the Bureau of Mines in cooperation with the Aluminum Co. of America, was to determine whether tae so-called Pedersen process3 can be applied to the blast furnace. This process consists of smelting a charge of bauxite, iron ore, and. limestone, and results in to products. One is a slag containing about 50 per cent of A1203 and is intended for use in manufacturing aluminum, and the other is iron low in sulphur. Complete details of the test are published in other reports4. Blast-furnace slag is now recognized as a satisfactory and economical raw material for making Portland cement, Wm. A. Forbes5 has recently reported that in 1926 an important steel interest used well over 1 million tons of slag in producing about 24 million long, tons of cement. This is equivalent to about ½ ton of slag for each ton of cement. Alumina cement can be made direct in the blast furnace. Its physical character would have to be changed by grinding, but no change in its chemical composition would be necessary.

Jan 1, 1928

By Frank E. Cash

Since ventilation adequate in quantity as well as quality is of paramount importance to the health and safety of men working underground in coal mines, mining officials, employees, and State inspection departments should give it the closest possible attention. MINING LAW OF ALABAMA The law governing, and regulating the operation of coal mines in Alabama was enacted in 1911 and amended or revised in 1923, 1925, 1930, and 1935. The original law and subsequent revisions were progressive steps in safeguarding the health and safety of underground employees.

Jan 1, 1939

By S. P. Kinney

[The blast-furnace operator is often confronted with the problem of determining the size of the materials which are used in the furnace burden. The statement is heard that the coke is larger or smaller or that certain ore is finer than that previously used. A screen analysis of the materials used gives a measure of the different sizes of materials in an aggregate. When one is fine and the other is coarse, the difference is obvious; but when the materials are of similar sire, it is more difficult to estimate the degree of finances or coarseness. In considering raw materials it would be desirable to be able to judge the size of the radio ideal materials entering the furnace and the burden as a whole, by one representative value, such as the average size of particle. Previous work by Perrott and Kinney3 developed a method for measuring the average size of particle in a mass of finely ground materials, and an attempt will be made to apply this method to the materials included in the blast-furnace charge and to the entire burden.]

Jan 1, 1930