Search Documents

By S. H. Katz

In the Bureau of Mines investigations of respiratory apparatus, a laboratory study of dust respirators has been conducted, and the results will be published in detail as a technical paper. Many industrial dust respirators, and many fabrics and filtering materials were tested. The principal results of these tests, and the conclusions drawn from them, are presented below. Reference to the patent literature discloses numerous types of dust respirators, mostly based on the filter principle. The present study included only representative filter-type respirators, purchased on the market.

Jan 1, 1926

By L. B. Pankratz

High-temperature heat-content values of gallium and scandium sesquioxides were measured over the temperature range from 298° to 1,800° K. The results fill gaps in the thermodynamic information for these compounds; no previous similar data existed. The heat-content values were combined with heats and entropies of formation to obtain free energies of formation of gallium and scandium sesquioxides to 2,000° K. The thermodynamic stabilities of the sesquioxides of aluminum, gallium, scandim, and yttrium were compared.

Jan 1, 1963

By B. J. Dalton

Several relationships between coexisting phases for analytical binary solutions near the critical point are given. These relationships were developed from a consideration of a (G u, P) surface at constant temperature and a (G u, T) surface at constant pressure, where G is the molal Gibbs free energy, u is the concentration of component 1 expressed as a mole fraction, G is the pressure, and T is the temperature. These formulas should facilitate the calculation of some of the quantities useful in making thermodynamic consistency checks on phase equilibria data about the critical point.

Jan 1, 1970

By James V. Kelly

During the spring and summer of 1947, the Bureau of Mines conducted an investigation and core-drilling program in the vicinity of the Rodham mine, approximately 4 miles north of Shullsburg, Wis. This work was undertaken as a part of a general study of the zinc and lead-producing area of southwestern Wisconsin. Work in the Rodham-mine area was done to investigate further a mineralized area frilled in part by the Puritan Exploration Co., a Delaware corporation, with offices in Galena, Ill. Some significant lead-bearing samples were obtained, but no continuous ore body was disclosed as a result of the Bureau of Mines work.

Jan 1, 1949

By Richard E. Ray, George N. Aul, Fred Garcia, William P. Diamond

Increasing longwall panel dimensions, particularly face width in gassy coalbeds, may result in unexpected increases in methane emissions. To investigate this problem, continuous longwall face emission monitoring studies were conducted at two adjacent mines operating in the Pocahontas No. 3 Coalbed, where longwall faces were to be extended from 229 to 305 m (750 to 1,000 ft). It was predicted by regression analysis of methane emissions data from 229 m (750 ft) wide longwall faces that extending faces to 305 m (1,000 ft) would increase methane emission rates by only 7 percent (0.6 m3/min (20 cfm)), to 8.6 m3/min (304 cfm) at the VP-1 Mine. In contrast, it was predicted that extending faces at the VP-3 Mine could increase methane emissions by as much as 13 percent (1.8 m3/min (65 cfm)) to 16.1 m3/min (567 cfm). The geologic and mine design factors influencing the variation in face emissions between the two mines will be discussed.

By Joseph J. Wallace

1. From the standpoint of known recoverable reserves, the following is the order of importance of the beds: Upper Kittaoning, Lower Kittanning, Upper Freeport, Lower Freeport, Middle Kittaning, Clarion, Pittsburgh, and Redstone. 2. mown measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and on 1,800 tons per acre-foot of coal in place, me estimated at 1,859 million short tons as of January 1, 1952. Of this, 1,351 million short tons me in beds 28 inches and more thick. Areas in each bed were omitted from the estimates because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1953

By George D. Drechsler

The purpose of this review is to provide an analysis of the supply and demand for coal in Europe in 1955-56 and estimates of future growth in European requirements as a medium for appraisal of the effects and benefits to the economy of the United States. This review stems from observations and evaluations made in contacts with Government and industry representatives of the principal countries of Europe and is based on detailed data selected from the established flow of unclassified economic and statistical material originating in overseas areas for use and deposit in the Bureau of Mines, Foreign Solid Fuels Section. This material includes current reports and analyses prepared by the United States Foreign Service, official reports of individual countries, foreign industry and trade publications, and the committees of the several European organizations engaged in continuing review and study of problems relating to fuels and energy. The review is presented in four sections: 1. Discussion of the more important factors relating to the present and future fuels and energy position of Western Europe.

Jan 1, 1957

By R. D. Ladoo

"At the beginning of 1920 a general feeling of optimism was noted in many talc-producing districts. The industry seems to have recovered from the temporary depression of the first half of 1919 and many mills are running at capacity production with their entire output for 1920 contracted for. The imports of talc for 1919 were only slightly larger than in 1918 by weight and probably no more by value. Thus foreign competition has not begun to be seriously felt. Several new companies in this country have been organized, some to operate new deposits and others to continue the work done by others.An interesting phase of the present situation is the possibility of increased use of talc in paint. There is a shortage of barium sulfate used as,paint filler. Since, for some uses, talc is considered second only to BaSo4 as a filler for paint, it is possible that part of the shortage could be relieved by an increased use of talc.A series of physical tests upon all pigment materials used in the manufacture of paints is being conducted for the Paint Manufacturers Association of the United States. It is important that all types of talc be represented in these tests. Producers of finely ground talc, 200 mesh and finer, are urged to submit samples of at least two pounds each of these grades that are available to paint makers with trade name and quality data, to the Institute of Industrial Research, 19th & B Streets, Washington, D. C., where the tests are being conducted.The Talc Products Company, Inc., Washington Building, Los Angeles, California, has recently been organized to develop a large body of talc one mile north of Riggs, San Bernardino County, California, This deposit contains a compact, white talc which can be sawed into crayons. The company's mill, at Los Angeles) is equipped with a unit of the Raymond system of grinding and air separation, and pencil sawing machines. It is reported that the pencils are being successfully used in Pacific Coast ship yards.The mining of talc where no mill is owned by the operator and the consequent sale of talc in its crude massive state has not proved profitable in a number of cases recently noted. Under exceptional circumstances, where mining costs are low and the product can be sold to a mill near the mine, the operation maybe profitable, but this condition is not common. One mine of this type has recently closed down, at least temporarily; but a second, more fortunately situated, in another district, is continuing operations, although plans are being made to erect a mill in the early spring. Most satisfactory results are ordi¬narily obtained where the mine and mill are owned by the same company.The sale of the Balmat mine of the International Pulp Company, near Gouverneur, N. Y., to J. H. McLear, Gouverneur, and H. G. McLear of New York, has been reported. It is stated that a large part of the property has been already leased to the Sylvia Lake Company, who will operate it. ""Cement, Hill, and Quarry""* states that ""the first mining done on this property was for silver and lead, but it developed into a good zinc producing property and later it was worked for its talc deposits. It has passed through several hands, the American Pulp Co., the Union Talc Co., and the International Pulp Co., all having had it in successive periods since 1891."""

Jan 1, 1920

By J. P. Walsted

The lack of an iron-smelting industry in the Pacific Northwest places the ferrous metals industries under an economic handicap. No iron-smelting enterprises, now dormant, had been operated successfully. Iron made at both of hoes installations proved to be satisfactory for normal pig-iron uses. Electric power and reductants acre available in the area. Power from the dames now completed and. those being constructed insures present and future needs for basic industries. Subbituminous coal, close to the main supply of iron ore, insures ample reluctant for all smelting requirements.

Jan 1, 1954

By Jacqueline A. McClaskey

The U.S. Bureau of Mines (USBM) Information and Analysis Directorate collects worldwide data on virtually every commercially important non fuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. The USBM's data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), which placed the collection of mineral statistics on an annual basis. The most recent authority for the USBM survey activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress). This act strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1993

By J. Wade Watkins

One potential peaceful application of nuclear explosives is stimulating the production of liquid or gaseous hydrocarbons from essentially nonproductive deposits of petroleum, natural gas, oil shale, and tar sands. Within the United States the appreciable difference between producible proved reserves and ultimate reserves and resources of hydrocarbon deposits is of such magnitude that much petroleum, natural gas, shale oil, and bitumen will not be produced unless significant technological progress is made in production techniques. The shattering effect of contained nuclear explosives and, to a lesser extent, the heat produced, have been considered as stimulative forces when the thickness, depth, and nature of such deposits permit considering the use of nuclear devices. Mechanical production problems would be less in an oil or gas reservoir than in an oil-shale or tar-sands deposit. Also, tar-sands resources in the United States may not be adequate to warrant serious consideration of applying nuclear-explosives stimulation. Gas reservoirs should present the least-radioactive-contamination problem. The technical feasibility of using nuclear explosives cannot be evaluated fully at present. Additional information is needed on the effects of pressure, heat, and radioactivity on the solids and fluids of hydrocarbon deposits, the nature and extent of induced fractures in different rock media, and the possibility of isolating and confining or removing radioactive contaminants. Final technical feasibility can only be determined by a field test. If technical feasibility is established, economic feasibility will depend upon the comparative cost of producing hydrocarbons by nuclear explosives and by conventional means. It is probable that an economic comparison would favor nuclear stimulation only where devices of relatively high yield could be used practicably and safely.

Jan 1, 1964

By T. A. Lang

The objective was to develop a Program Plan of analytical studies and tests for determining (1) the optimum installation tension of a coal mine roof bolt, (2) the most valid bolt support theory or theories, and (3) the most valid roof failure theory or theories. On this basis a comprehensive literature search was made and significant material dealing with coal mine roof behavior, roof bolting and roof support was collected, reviewed, classified and analyzed. Emphasis was given to the influence of rock reinforcement on the control of deformation, stress field modification and mine roof stability. An assessment was made of the effect of various parameters including bolt tension, bolt pattern and time of installation, on the effectiveness of rock reinforcement systems, and equations developed for bolt tension as a function of these parameters, and rock properties. From these studies, a major program plan of tests and studies was developed for verifying and validating the most tenable theories of roof behavior and roof support and for determining optimum bolt installation tension.

Jan 1, 1979

By C. A. Herbert

The mine of the Alpha Portland Cement ..Co., Iroaton, Ohio, ..working in. a. bed of limestone 96 feet thick at a depth of approximately 510 feet below the surface, has established a won¬ derful safety record, having operated 6 years—frcra September 21, 1926,. to September 21, 1932 - without a lost-time accident. This mine, with 61 to 86 employees (average 68) and daily output of 1,000 to 1,200 tons of limestone, operated 1,041 days during the 6-year period, or the equivalent of 578,894 man-hours of exposure. ...... ... . Immediately above the limestone is a 20-foot .bed of hard..sandstone.. At present about 10 feet of limestone is left up as. a roof and.about. 42 feet is being extracted. Of the lower portion of the bed it is believed that about. 25 feet. ..immediately below . the .present workings is suitable for cement and will be extracted later. The mine workings are reached by two rectangular concrete shafts, one a 2-compartment hoisting shaft and the other a 2-compartment air and escape shaft- In the latter shaft one compartment is used as an airway and the other, as a cage compartment fo.r a man and material cage. .. . - . The tipples at both the air shaft: and. hoisting shaft are-of steel. The.ground landings at both shafts are fenced in with hand-operated gates in front of the cage compartments.- The two shafts and the crushing plant, which .is.a part of the hoisting shaft-tipple structure, are adjacent to the mill buildings. The rock is hoisted on self-dumping cages in 4 ton capacity, end-gate, steel cars. An electric hoist with automatic overwind device is used at both the main shaft and air shaft. The controls for the main hoist are in the tipple where the engineman is stationed and from which point he has an unobstructed view of both the ground, landing and the cage coming into the dump.

Jan 1, 1933

By C. J. Chindgren

A refractory-lined, garage-type automobile incinerator with a natural gas afterburner for air pollution control was cooperatively constructed and tested by the Bureau of Mines and the Wasatch Metal & Salvage Co. in Salt Lake City, Utah. The incinerator is capable of relatively smokeless burning of 32 to 60 cars per day, dependent on the degree to which the cars are stripped prior to incineration. Preliminary burning campaigns indicate the cost of incineration to be approximately $2.75 per car.

Jan 1, 1970

By L. E. Geyer, W. W. Adams, M. G. Parry

"More than 73 million pounds of rock dust were used by the bituminous-coal-mining companies in the United States during 1930 to present or limit loss of life and destruction of property from explosions of gas and coal dust in underground mining operations, according to statistics compiled by the United States Bureau of Mines from reports furnished by mine operators. The mines using rock dust produced 65. 691, 753 tons of coal during the year, more than 30 percent of the total production of bituminous coal from underground mines in the United States that year. Although only 382 out of a total of 5,629 active underground bituminous mines applied rock dust to underground working as a precaution against explosions, they were chiefly the larger producing mines, employing 25.4 percent of all of the underground bitumious mine workers in the United States and accounting for 27.4 percent of the total number of man-hours worked underground at bituminous mines.a summary of the reports for the 382 mines using rock dust showed a total production of 96,691,755 tons of bituminous coal, 89,503 men employed underground, and 129,718,965 man-hours worked by the underground employees. (See tables 1 and 2.) These mines averaged 8.76 pounds of rock dust per ton of coal shown by reports from 385 mines using rock dust in 1932 (See table 3.)"

Nov 1, 1935

By A. L. Murray, P. A. Surgeon

The Spring Canyon Mine Rescue Association is a cooperative association supported jointly by five coal-mining companies located in Spring Canyon, Utah. The properties of mining companies the Carbon Fuel Co, Rains , Utah, the Liberty Coal Co. , Latuda, Utah, the Standard Coal Co. , Standardville , Utan, the Spring Canyon Coal Co. , Storrs , Utah, and the Peerless Coal Co. , Peerless , Utah about a mile apart and normally employ a total of 915 men , 733 underground 182 on the surface . and The Association was organized on July 5, 1921 , and Rudolph Clark, fomerly first - aid miner on U. S. Bureau of Mines Rescue Car 11 , was placed in charge. as manager . A board of directors made up of a representative from each of the cooperating companies (usually the mine superintendent ) is the governing body of the Association and the expenses are prorated on a basis of the production of each of the five mines . The Association maintains eight sets of Gibbs rescue apparatus and a motor truck fitted up as a combined rescue truck and ambulance . Additional apparatus are to be purchased . Standardville is the central camp in the canyon and has been made the headquarters of the Association . The apparatus are now kept and the truck housed in a small station, but plans have been prepared for a large station which will be built this summer . This new station will have a large apparatus room , a test chamber, a suitable room. for training, and a garage on the first floor, while above will be the living quarters of the manager . There is a good road through the canyon and the other camps are all within two and one -half miles of Standardville .

May 1, 1922

By N. S. Dalal, X. Shi

"Electron spin resonance (ESR) spin trapping methodology has been used to study the reactions of manganese dusts with glutathione, employing a-{4-pyridyl-1-oxide)·N-tert-butyl-nitrone (PBN) and 5,5-dimethyl-1-pyrroline-N-oxide (DMPO) as spin traps. The results show evidence for the glutathionyl radical formation in the reactions of both MnO2 and manganese (Ill) acetate with glutathione. Based on these experimental observations, we hypothesise that the mechanism of neurotoxic effects of manganese might be due to the fact that the generation of glutathionyl radicals depletes the glutathione pool and reduces the glutathione shield against free radical products of dopamine metabolism and manganese induced reactive oxygenated species. IntroductionExposure to manganese compounds often occurs as the result of foundries and mining operations (1. 2). Other significant sources of environmental manganese include coal-fired power plants and burning of residual and crude oil (3, 4). Lately gasoline combustion has also started to contribute since manganese (methyl cyclopentadienyl manganese tricarbonyl. 0. 125 g/gallon) is being used instead of lead as an antiknock ingredient in automobile fuels (5. 6). Although manganese is an essential element in certain biological processes it is toxic in excessive amounts. The manganese toxicity is mainly associated with the nervous system (7-9). Symptoms frequently observed in manganese poisoning or manganism are disorientation, memory loss, anxiety, compulsive laughing and crying, mask-like faces, akincsia rigidity and tremor (10). In spite of numerous investigations to understand the mechanism of manganese induced injury. it has not been possible to localize the initial chemical lesion responsible for altered physiology and ultimate cell death. This may perhaps he the reason for failure in developing a successful therapy for manganese intoxication."

Jan 1, 1990

A prototype EM Location System was fabricated and tested at the Geneva Mine near Dragerton, Utah. This system consisted of six manpack transmitters and six manpack receivers covering the frequency band from 900 Hz to 2900 Hz as well as a six channel receiver designed for use in a helicopter. Tests showed that EM signals from lightweight (314 lb) transmitters could be detected both on the surface and from a helicopter through -2 as much as 1650 ft of relatively high conductivity (2 X 10 mhos/m) over- burden. Furthermore, the resulting field strength profiles could be used to determine source location to within 150 ft of the actual surveyed location in the mine. Modifications were made to a Monitoring, Locating and Communications System being tested at the Bruceton Mine, Pittsburgh, Pennsylvania. These modifications have improved the performance and quality of the paging and voice telephony mode of the system. Subsurface receiver modifications have improved reception of voice downlink signals.

Jan 7, 1973

By H. C. Ko

The Bureau of Mines maintains an active program in thermochemistry to provide thermodynamic data for the advancement of mineral science and technology. As part of this effort, the standard enthalpy of formation at 298.15 K, ?Hf°, for 2CdO-CdSO4 was determined by HCI acid solution calorimetry to be -345.69 ±0.61 kcal/mol.

Jan 1, 1983

By Chas. F. Jackson

This paper is a tabular compilation of data contained in a series of information circulars dealing with mining methods and costs at a large number of mines in the United States and some foreign countries. There circulars have been published from time to time during the years 1929 to 1934 inclusive. From time to time, as enough data became available in these circulars, other circulars and. bulletins have been published in which the data bearing upon different phases of nine operation were summarized, discussed, and analyzed. The present paper is a compilation of data on costs of drifting and crosscutting contained in earlier circulars, .designed to assemble this information in a convenient form for reference without attempting lengthy discussion of details of drifting and crosscutting practice. For such details the reader is referred to the circulars on individual mines.

Jan 1, 1935