Search Documents

By J. B. Littlefield

The term "konimeter" is used generally to designate a type of dust-sampling instrument that collects the dust from a small volume of air by impingement on a glass plate prepared aced with an adhesive film. The konimeter was first developed by Sir R. N. Kotze about 20 years ago and was followed a few years later by the circular-type konimeter, by which a number of samples may be collected on a glass disk. The present discussion will be confined to the circular type, as it is used most. Various techniques have been developed for using the konimeter, and many materials, such as petrolatum, mineral oil, and glycerine jelly, have been used in preparing the adhesive film. In South Africa, Australia, and Canada, where the konimeter has been employed most widely, dust samples are treated by ignition and washing before being counted. In Canada the dust samples are collected on a disk of special heat-resistant glass prepared with a film of mineral oil; the disk is then heated to a dull cherry-red in a muffle-furnace to remove the film and organic matter, cooled, and washed with a few drops of 50-percent hydrochloric acid followed by distilled water and alcohol, and then heated again to remove residue left by evaporation of the alcohol. After this treatment, the dust samples are counted under a magnification of 150 diameters with dark field illumination.

Jan 1, 1938

By W. W. Adams

luring the past two years the Bureau of ?,lines has been receiving from 100 to 150 coal mines in various States a report of each accident causing death, permanent total disability, permanent partial disability, or temporary disability lasting beyond the remainder of the day or shift on which the accident occurred. For each 100 accidents in these groups, there are perhaps from 35 to 45 accidents that do not disable the employee beyond the remainder of the day, and of these fraction-of-a-day accidents the Bureau has compiled no statistics. Information revealed by the reports is to the effect that falls of roof and coal in bituminous coal mines are responsible for 28 per cent of the temporary injuries to underground workers and 33 per cent of the days lost from all temporary injuries underground; they also indicate that falls caused 59 per cent of the deaths from all causes underground. Figures compiled by R. N. Hosler, of the Pennsylvania. Mine Rating Bureau, and covering accidents in bituminous; minis in that State, chow that 61 per cent of the deaths underground during the years 1917-1921 wore due to falls. Neither of these percentage figures includes deaths in major explosions; figures for all bituminous mines in the United States during the five years 1920-1024, inclusive of deaths in major explosions, show that 52 per cent of the deaths underground and in shafts were due to falls of roof and coal.

Jan 1, 1925

By Manuel Gomez

A computerized moving average technique was developed to interpolate coal seam characteristics between sample points. The interpolative method coupled with multivariate regression analysis and simulation procedures was used to forecast coal properties not readily obtained from an analysis of drill core samples. Coal property forecasts were of two kinds: (1) specific mine property forecasts that are suitable for mine product control and yield a good approximation of the local variation along both the vertical and horizontal axes of the seam, and (2) regional estimates where much of the local seam variation is smoothed out, but the general trends are maintained. Forecasts of the volatile matter, ash, total sulfur, and the heating value for part of the Pittsburgh seam located in Ohio, Pennsylvania, and West Virginia were in good agreement with independent evaluation data. Spatial configuration for preparation characteristics, particularly, the effect of crushing on sulfur release, low-and high-temperature carbonization properties, the Hardgrove grindability index, the coal hardness index, gasification variables, and hydrogenation factors were constructed for the same area of the Pittsburgh seam. These forecasts may be developed from drill core data collected in the exploration phase of mining. The results, which may take the form of a series of maps, are useful to mining, chemical, and combustion engineers, to economists and mine managers, as well as to coal users for mine design, economic analyses, energy forecasts, utilization studies, mine product control, and environmental control and programming.

Jan 1, 1974

By R. E. Thill

The ultrasonic pulse measurement system described measures velocities of longitudinal (compressional) and shear waves in rock to give values that can be used with density values to determine the dynamic elastic constants of rock. A special feature of this pulse measurement system is its unique acoustical bench that minimizes errors in pulse transit times that are commonly associated with coupling, sample alinement, and sample orientation. Some special features of the acoustical bench are its highly versatile transducer cartridges, a pneumatic ram coupling device, an orientation mechanism, and a vacuum chuck sample holder. The lathe-bed-like construction of the acoustical bench assures automatic alinement of samples and versatility in accommodating samples of various shapes and sizes.

Jan 1, 1968

By B. J. Dalton

The Bureau of Mines Helium Research Center has as a long-range objective the development of an equation of state for helium that will allow all of the thermodynamic properties to be calculated within the accuracy with which they are known. If this objective is to be realized, a method of calculation must be known. This report gives the principles of the method we use in such problems. A computer program was developed for predicting these properties, including those at the critical point, that is perfectly general and applicable to any equation of state. To demonstrate the efficacy of our method, this computer program was used to evaluate thermodynamic properties of a Redlich-Kwong fluid in the two-phase region. Expressions for calculating various thermodynamic functions specific for this particular equation of state are derived. Numerical values are tabulated and graphs are presented for all functions calculated. It is shown that for a Redlich-Kwong fluid there are finite discontinuities in (1) the second temperature derivative of the Gibbs free energy or chemical potential at the critical point, (2) the second derivative of the vapor pressure curve with regard to the temperature on passing through the critical point, and (3) the measured heat capacity at constant volume on passing through the critical temperature when the calorimeter is filled to the critical density. It is also shown that the heat of vaporization is infinite for a Redlich-Kwong fluid at absolute zero.

Jan 1, 1969

By Frank E. Cash

"INTRODUCTION The producing iron-ore ranges in the Lake Superior district are the Marquette and Menominee in Michigan, the Gogebic in Michigan and Wisconsin, and the Cuyuna, Mesabi, and Vermilion in Minnesota. These ranges produce about 85 percent of the iron ore mined in the United States. The accident experience in connection with this production is better than that of the regions producing the remaining 15 percent. Production and shipments vary slightly from year to year owing to stockpiling underground ore during the winter, or nonshipping, season but closely approximate each other over a period of years. This information circular supplements, combines, and continues the data contained in Information Circulars 7321 3/ and 7410 4/, including statistics for 1946 and 1947.Whereas the title ""Accident Experience"" is used for uniformity and logical indexing throughout this report, ""injury"" will be used as a general term to apply to disabilities of all degrees.During the 8-year period 1940 to 1947, inclusive, 619,054,023 long tons of iron ore was shipped from the Lake Superior district. 5/ Michigan and Wisconsin shipped 117,828,939 tons, or 19.03 percent of the total, and employed approximately 9,260 men. Minnesota shipped 501,225,084 tons, or 80.97 percent of the total, and employed an approximate annual average of 12,260 men. The tons produced and shipped per man employed in Minnesota is much greater than in Michigan and Wisconsin, owing to the large open-cut production in Minnesota."

Jun 1, 1949

By Terry S. Cory

This report describes the results of a measurement and analysis program to characterize wireless radio transmission in metal/non-metal mines over a wide frequency range from 0.2 - 1000 MHz and over a variety of mine environments. Six mines were chosen based on the relative economic significance of their product to the U.S. economy. Mine types include oil shale, uranium, potash, lead/zinc, copper, and silver. Particular mines were chosen so that the group would embody the most important mining techniques. The results show that transmission at medium frequencies are optimum for wireless mine communications, in agreement with extensive testing previously performed by the authors In coal mines, and that mine-wide wireless systems are feasible with a minimum requirement for new dedicated wiring. At least one need for such a wireless system was identified in each mine visited.

Aug 1, 1981

By M. Kanda, W. D. Bensema, J. W. Adams

Two different techniques were used to make measurements of the absolute value of electromagnetic noise in an operating hardrock mine, Grace Mine, located near Morgantown, Pennsylvania. Diesel-powered haulage equipment is used in this mine, and the electromagnetic noise environment it creates was measured to see how it differs from the environment created by electric-powered haulage equipment. One technique measures noise over the entire electromagnetic spectrum of interest for brief time periods. Data are recorded using broadband analog magnetic tape and are later transformed to give spectral plots. The other technique records noise amplitudes at several discrete frequencies for a sufficient amount of time to provide amplitude probability distributions. The specific measured results are given in a number of spectral plots and in amplitude probability distribution plots.

Jan 6, 1974

By John Hays Hammond, James Douglas, J. PARKE CHAN- NING, W. R. Ingalls, J. R. Finlay

The committee making this report, consisting of Walter Renton Ingalls (chairman), J. Parke Channing, James Douglas, James R. Finlay, and John Hays Hammond, was originally appointed at a meeting of the American Mining Congress at Denver, Colo., in No- vember, 1906. The object of this appointment was the drafting of a modern law governing quarrying and metalliferous mining which could be recommended to the several States for adoption, in the hope that the passage of such a uniform law by the mining States would tend to lower the number of fatal and serious accidents. The first step of the committee (the personnel of which has re- mained unchanged from the beginning) was to procure copies of existing laws from the officials of the several States of the Union. With the assistance of the Engineering and Mining Journal, copies of the laws of Great Britain, the Transvaal, New South Wales, Victoria, Queensland, Western Australia, Tasmania, New Zealand, and certain European countries were also obtained. The replies to the inquiries made at that time developed the fact that a number of States in which mining was carried on had no laws at all. Other States were found to have elaborate provisions regulating coal min- ing, but none applying to metalliferous mining. Still other States were found to have miscellaneous and unrelated provisions passed at odd times, seemingly as the result of the occurrence of some dis- aster or other.

Jan 1, 1915

By Noel N. Moebs

The Bureau of Mines investigated severe coal mine roof support problems along a section of main entries in the Pittsburgh coalbed in southwestern Pennsylvania to identify the causative factors. The mine roof was examined in detail, and various sedimentary structures are described that contributed directly to irregular and unstable roof. Small-scale paleochannels, scours, and related slickensides were identified as the leading cause of bad roof, and isopach maps were prepared to illustrate a method whereby the presence of these structures could be inferred in advance of mining. Probably second in importance was the occurrence of relatively incompetent flaggy, poorly cemented sandstone, weakened by coal and micaceous laminea. No effect of in situ stresses on roof stability was detected.

Jan 1, 1977

By J. W. Adams

Measurements of surface magnetic field noise were made at various locations over the Geneva Coal Mine near Price, Utah, on June 12, 1973. The locations selected were on the surface over emergency locator beacons underground at depths between 3S0 meters (1150 ft.) and 488 meters (1600 ft.). The surface terrain where these measurements were made was mountainous, and access was difficult. There were no power lines within several miles, and the weather was clear; therefore, the magnetic noise levels were about as low as will normally occur. Results of measurements of distant sferics indicate rather sharp cutoff frequencies below which broadband, impulsive noise is attenuated. The mechanism of propagation for this noise above the daytime cutoff frequency of 3500 Hz and the nighttime cutoff frequency of 1700 Hz is deduced to be a waveguide formed by the D or F layers of ionosphere as an upper plane and the earth as a lower plane.

Jan 1, 1974

By H. W. Kilau

The U.S. Bureau of Mines examined the wettability of bituminous and subbituminous coals before and after exposure to ambient air atmosphere, as part of an ongoing project investigating the coal-wetting abilities of surfactant solutions intended for the suppression of dust during coal mining operations. Exposure periods were generally 7 days or less, and the changes in wetting response were measured with a capillary penetration apparatus. Wetting solutions tested included a nonionic surfactant, two anionic surfactants, and pure distilled water. After exposure, higher ranked bituminous coals treated with nonionic surfactant solution and pure water showed increased wettability, but lower ranked subbituminous coals showed decreased wettability. With the anionic surfactants, the coals demonstrated opposite responses. The wettability changes appeared to be related to the coal moisture content. These changes may be amplified by specific, but incompletely understood, interactions between surfactant polar groups, absorbed water, and the coal surface.

Jan 1, 1989

By W. D. Dietzman

This Bureau of Mines report presents a continuation of statistics pertaining to distribution of petroleum reservoirs (or fields), wells, and production by depth and producing rate classification in the United States. These statistics show the change that has occurred since results of a similar study were published by the Bureau of Mines in 1967. Data are presented in tabular form by State for the 18 principal oil-producing States and by subdivision for the two larges t oil-producing States, Texas and Louisiana, Tabular summations and graphical illustrations are presented for the Nation. The data are classified by 4-barrel-of-oil-per-day rate increments up to 36 barrels and one increment of greater than 36 barrels of oil per day and by 2,000-foot depth increments up to 8,000 feet and one depth increment of greater than 8,000 feet. The overall average producing rates for States and the Nation have been published for many years; although such rates are useful, they are very general descriptions of producibility. A breakdown of production, wells, and reservoirs by various depths and rates and by State or by State subdivision provides a more detailed description of producibility.

Jan 1, 1976

By Craig S. Compton

The failure of the immediate roof or "roof skin" between installed primary and secundary roof supports causes hundreds of injuries and, on average one or two fatalities each year in U.S. underground coal mines. Conventional roof supports cannot cover enough roof area to adequately control these relatively small, but very dangerous rock falls. The 2006 Mine Safety and Health Administration (MSHA) accident database lists a total of 542 ground fall injuries, including 10 fatalities. An analysis of the database suggests that 434 of the injuries and three of the fatali­ties can be attributed to roof skin falls (See Figure 2). The key to controlling falls of the immediate roof or roof skin is maximizing the area of roof coverage ilnd confining these relatively small loose rocks. Roof screen offers maximum coverage of the immediate roof. Depending on the size and configuration of the screen panels, coverage of up to 100% of the roof area is possi­ble. Screen also offers a first line of defense for machine operators working in the face area by confining or deflecting small rocks that can come loose during mining or roof bolt installation. Figure 1 shows an example of the protection screen provides dur­ing bolt installation. Although the benefits of screen are well-known, mining com­panies in some areas of the U.S., mainly Northern Appalachia and the Illinois basin, are not convinced that roof screen is the best tool for dealing with roof skin control issues. The logistics of material handling, possible ergonomic injuries to workers, and the costs associated with installation are delaying the acceptance of screen as an on-cycle roof support tool. Other mines however, have concluded that installing roof screen can be cost-effective when compared to the cost of lost time accidents, training of replacement workers, or returning to already developed entries for the cleaning and rebolting process.

Jan 1, 2009

By P. C. Van Natter

Numerous mine fires have resulted in high death tolls and considerable finan¬cial loss during the history of coal mining. In most instances the death toll and financial loss were greater because of inadequate fire-fighting facilities. The information in this report is presented in the hope it may serves as a guide in the selection, placement, and care of fire-protection systems in similar coal mines. The adequacy of fire protection varies according to size of operation, employment, and production. When fires occur on the surface or underground, measures must be applied quickly to prevent incipient fires from spreading. The record of coal-mine fires shows that, in many instances, facilities for combating fires were very meager or were absent. It would be virtually impossible to establish and maintain all the necessary facili¬ties that may be needed to extinguish widespread mine fires, but it is believed that the coal industry can ill afford less than the minimum required by other industries where the time element and avenues of escape are much more favorable.

Jan 1, 1958

By W. P. Haynes

The Bureau of Mines has been studying a modified steam-iron process using coal-derived producer gas for making either hydrogen plus carbon monoxide or methane. To provide a guide for this experimental study, compositions of equilibrium product gases for the reaction of steam plus carbon dioxide with iron were calculated and are discussed in this report. The calculations, which are described in this report, are based on thermodynamic data in the literature and cover temperatures from 800° to 1,300° K., pressures from 1 to 30 atmospheres, and hydrogen-to-carbon atomic ratios in the gas of 4 to 12. The equilibrium gas compositions are discussed in regard to making hydro-gen, carbon monoxide, and methane in the oxidation step of the modified steam-iron process. From the viewpoint of thermodynamics alone, assuming the reactions reach equilibrium, the discussion considers the effects of temperature, pressure, and composition of feed gas upon the composition of the product gas, the degree of oxidation of the iron, and the possible deposition of carbon. The results indicated the following: (1) Nearly all the carbon can be converted to methane at low temperatures (800° to 900° K.) and high pressures (over 20 atmospheres); (2) to obtain high yields of synthesis gas, high temperatures are required. For example, at 30 atmospheres, a temperature over 1,200° K. is required to convert 60 percent of the steam plus carbon dioxide to hydrogen plus carbon monoxide. Lower temperatures may be used at lower pressures) (3) oxidation of the iron increases with increasing pressure and decreases with increasing temperature; and (4) process conditions favoring carbon deposition were found within the range of variables studied, but it is thermodynamically possible to operate the oxidation process with steam and carbon dioxide outside this range of carbon deposition.

Jan 1, 1961

By James E. Hill

In the course of exploratory drilling during World War II by the Bureau of Mines under the Strategic and Critical Minerals investigations Program, a problem arose as to the ultimate disposal of the drill core resulting from that program. The difficulties experienced in obtaining factual information to evaluate mineral deposits examined (during that program) influenced the Bureau in a decision to catalog and store the drill cores for future reference. Initially, the drill cores were stored at the nearest Bureau of Mines station that had space available for the purpose. Recently the Bureau stations at Minneapolis, Minn., and Denver, Colo., were designated as the locations of permanent drill-core storage facilities. Drill cores that are retained from Bureau of Mines mineral-exploration projects are stored at these two locations and are given preference in selecting cores for storage. Drill cores are accepted also for storage from other Government agencies, State agencies, private companies, or individuals on the basis of available facilities and consistent with the significance of the core in relation to Bureau of Mines objectives and national interest. Selection and acceptance of such drill core are determined by the Bureau of Mines. The drill cores stored at the two locations are available for inspection by any person having a legitimate interest in the mineral deposits represented by the cores. Approximately 1,850,000 feet of drill core can be stared in the facilities now available to the Bureau of Mines. Approximately 475,000 feet of drill care is stored or scheduled for storage at Minneapolis, Minn., and 240,000 feet of core stored or scheduled for storage at Denver, Colo. A list of drill core now in storage at the Bureau of Mines core-storage facilities at Denver and Minneapolis is included as appendix A.

Jan 1, 1957

By Bill M. Stewart, Phil W. Patton, Curtis C. Clark

Back injuries from handling materials in underground mines continue to be a major safety problem. In spite of the ingenuity of many people and the development of numerous mechanized aids, the number of materials-handling injuries remains second only to the number of roof fall injuries in underground coalmines. Relocation and repositioning of electrical cable, conveyor belt parts, and roof bolt sup-plies in particular are the sources of significant numbers of back injuries. To help reduce such injuries, researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health are examining Mine Safety and Health Administration accident data to determine correlations between materials-handling tasks and the number of back injuries. Also being investigated are new technologies used in underground mines in the United States. Equipment is being developed or modified that would replace the necessity of doing lifting tasks manually. A Coleman manipulator was tested, and modifications were made to make it more suitable for underground mine use. To reduce or eliminate the need to manually clean off materials that commonly plug grizzly openings, a track-guided pincher arm device was developed. Oversized rock can be broken with the pincher arms in the up position, and the arms can be lowered to grab and remove debris. The arm can also be used in a sweeping action to remove cohesive fines that may bridge grizzly openings.

By A. B. Hooker, J. W. Paul

"There was a time when any suggestion that the Davy flame (safety) lamp be discarded, would have evoked unlimited, criticism. However, that time is past.Investigations both here and abroad have shown conclusively that the Davy lamp does not have the necessary factor of safety against ignitions of mine gas, and England, the lost stronghold of the Davy lamp in Europe, has eliminated this lamp and substituted safer types.In the United States there are companies who still use the Davy lamp in spite of all that has been said and published as to the dangers connected with its use.Recently the purchasing agent of an anthracite coal company requested the Department of the Interior, Bureau of Mines, to pass upon the safety of some braise gauzes for use in a shielded Davy lamp. A shielded Davy lamp is an ordinary Davy safety lamp equipped with a circular brass shield that is attached to the lamp posts. This shield extends about one-half way around the gauze and one-half of the gauze height. The main purpose of the shield is to prevent the lamps being extinguished by a sudden increase in the velocity of the air current past the lamp.The brass gauzes submitted for this test represented two grades of brass - a yellow brass and a red brass. The analysis of these brasses was not determined. Two shielded Davy lamps that were submitted for the tests each had a steel gauze. These steel gauzes were also tested. Tests were made in horizontally moving mixtures of Pittsburgh natural gas and air at velocities of 400 to 1,000 feet per minute. The gas percentages used were 7%, 8.6%, and 11%. Tests were made with the lamp shield in two positions relative to the lamp and direction of flow of the gas-and-air mixture. In one position the shield was between the gauze and flow, as normally used. In the other position the shield was on the downstream side of the lamp. The tests were continued until one or more failures or gas explosions been obtained with each of the six gauzes. The results of these tests summarized as follows:"

Jun 1, 1923

By H. O. McDonald

The Bureau of Mines reviewed the chemical vapor deposition (CVD) literature on the nonmetal binary and ternary compounds of the group IVB, VB, and VIB elements, with emphasis directed to the following nonmetals: B, C, N, O, and Si. This review examines each of these binary and selected ternary compounds of the group IVB, VB, and VIB elements as coatings and gives some of their preparative methods, uses, and properties. A total of 259 references were found for these compounds of the nine elements. This review was utilized in the Bureau's research to provide abrasion-, erosion-, and corrosion-resistant coatings in order to conserve critical metals and protect various metallic surfaces in metallurgical, mining, and energy conversion systems.

Jan 1, 1983