Search Documents

By Earl W. Waay

"Since the beginning of the petroleum industry in 1839, up to within two or three years ago, these has been a dearch of engineers who have had the fundamental technical training also sufficient practical experience so that they could compete with practical men. Need for Technical Investigations in Industry: As in the early stages of the mining industry, the petroleum industry has been rather slow in realizing the need for technical assistance and investigators in the development and production of oil lands. The rapid increase in consumption, however, during the past few years has accentuated this need more than anything else could have done. When it is realized that our production cannot longer keep pace with the demand, it is easily understood why it is imperative that be instituted which will tend to conserve and prolong the supply of oil from the fields now known. It is interesting to note from preliminary production figure given cut by the U. S. Geological Survey, for the year 1919, that the United States produced about 430,000,000 barrels, an increase of 22,000,000 or 6 per cent over 1918 production and also there was imported, chiefly from Mexico, a little over 52,000,000 barrels, making a total of 430,000,000 barrels, to satisfy the trade demand in the United States of which almost 6,000,000 barrels was exported. Stocks were not materially increased.Other significant facts regarding our petroleum industry, are that just recently the U. S. Shipping Board in soliciting bids for 24,000,000 barrels of fad oil to meet prospective needs, received bids for only 1,500,000 barrels at prizes ranging from 75 to 90 per cent higher than was paid last year. One large company on the Pacific Coast has stopped its export trade, and has notified consumers,of gas-engine distillate that they will no longer make deliveries of this product. This will materially affect the farmer, in many instances, through his use of the truck and tractor."

Apr 1, 1920

By S. P. Kinney, A. C. Fieldner, S. H. Katz

"1 Introduction The regrettable death of James S. Cunningham, Foreman Miner, attached to Bureau of Mines Rescue Car No. 2, while wearing a half-hour type oxygen breathing apparatus in a gasoline storage tank at Trinidad, Colorado, raised the question as to the possibility of gasoline vapors permeating the rubberized fabric of the breathing bags of such apparatus.It is known that most gases and especially certain organic vapors permeate rubber, by solution or a similar process. The rubber becomes saturated with the gas and if a concentration of gas is maintained on one side of the rubber sheet it slowly gives off gas from the other side. It of course takes some time for the gas to diffuse through the rubber and the length of time before it reaches the other side is proportional to the thickness of the rubber. The amount of gas that passes through per unit of area in unit time increases with the concentration of gas and also varies with the structure and composition of the rubber.It has been suggested that the gasoline vapor could not have penetrated into the interior of an oxygen breathing bag because the pressure is greater on the inside, but this is not true as the process of permeation by solution in the rubber is affected only by the difference in the partial pressures of gasoline vapor on the inside and outside of the bag. The positive oxygen pressure on the inside can only prevent the entrance of gasoline vapor through measurable holes, and has no effect on permeation by diffusion through the rubber."

Dec 1, 1919

By A. Wahab Khair, N. P. Reddy

"Abstract. This paper attempts to characterize coal breakage due to the action of a continuous miner. Coal blocks with an approximate dimension of 45.7 cm x 38.1 cm x 15.2 cm (18 in. x 15 in. x 6 in.) were first subjected to confining pressures equivalent to in-situ conditions. Then the blocks were cut along the face/butt cleat direction by the cutting head of a specially designed unique automated rotary coal cutting simulator (ARCCS), simulating the action of the continuous miner in underground coal mining. During the tests under a particular set of in-sit and operating parameters a number of other para¬meters such as 1) penetration of bit into coal, 2) penetration resistance (thrust and cutting pressures), 3) rotating velocity of cutting head, and 4) acoustic emission activity in the coal block were monitored. After each cutting cycle the fractured surfaces were photographed and a velocity survey was conducted by using a sonic technique. At the end of each experiment, the coal fragments were collected in bags using a vacuum cleaner. These fragments were then sieved for size distribution analysis.INTRODUCTIONThe Federal Coal Mine Health and Safety Act of 1969 was enacted to emphasize to coal operators that the airborne respirable dust should not exceed 2 mg/m3, thus reducing the incidence of coal workers pneumoconiosis.Dust control techniques such as conventional water sprays and dust collectors are only partially effective and require additional equipment expenditures. A more authentic approach would be to reduce respirable dust at the source the continuous mining machine cutting head, where the fragmentation process occurs. Improving the fragmentation process by characterizing the coal breakage will not only reduce respirable dust at the face, but it will also decrease the amount of respirable dust that is liberated during the secondary handling.Fragmentation of coal can be expressed as a function of three major groups of parameters; namely, 1) coal properties, 2) in-situ conditions and 3) operating parameters. This paper deals with the characterization of coal breakage along both face/butt cleat direction as a function of machine operating parameters such as rate of advance, angle of attack, bit configuration, bit lacing (spacing and pattern) and bit speed at various equivalent in-situ pressures."

Mar 1, 1989

By L. W. Kelly

The purpose of this paper is to indicate some of the benefits that have been derived in the Zeigler No. 3 mine by using roof bolts under extremely adverse roof conditions J with the thought that much better results could be obtained in other mines with more normal roof conditions by applying some of the practices that were developed in this mine. Some of the benefits that have been obtained in this mine, which will be shown in this paper, are: 1. Increased tonnage per man-shift at the face when roof bolts are used, as compared to the tonnage under similar conditions when conventional timbering methods were used. 2. Increased efficiency of roof bolting by giving the foremen a definite plan to follow. 3. Reduction in delays caused by failures of the trailing cables of loading, mining, and drilling machines. 4. Reduction in the number of accidents after roof bolting was adopted. Inasmuch as the success that followed roof bolting in this mine was obtained under one of the most treacherous roofs in the Middle West, it is reasonable to suppose that correspondingly better results could be obtained under more favorable roof conditions by using the same procedure.

Jan 1, 1952

By H. K. Sacks

The Bureau of Mines has improved a mine dust incombustibles analyzer originally developed at the Bartlesville Energy Research Center (BERC). This analyzer provides quick, accurate analysis of the percentage of incombustible material present in dust samples taken from mine ribs, roof, and floor so that costly overdusting may be eliminated while still maintaining a proper level of incombustibles. The changes being effected on the present design of the BERC model IV rock dust analyzer should simplify its operation and calibration procedures, resulting in increased accuracy.

Jan 1, 1976

By Richard L. Sayrs

"The Stiner zinc prospect near the north boundary of Union Tennessee, and the Bunch Hollow property 5 miles northeast in Claiborne County, Tennessee, were diamond-drilled by the Bureau of Mines during the period .September 1, 1944, to February 22, 1945. Seventeen holes totaling 5,687 feet were completed, 13 of which, totaling, 5.083 feet, were on the Stiner property and the remainder, totaling 604 feet, at Bunch Hollow.The Stiner prospect is about 1 mile east of the old workings known as ""New Prospect"" or ""Lead Mine Bend."" The Federal Geological Survey made a study' of the area early in 1944. The prospect was first visited in August 1944 by Bureau of' Mines engineers3/ accompanied by members of the Federal Geological Survey.4/ The locality is reached by traveling State Road 33 north-about 9 miles from Maynardsville, Tenn., thence northwest about 7 miles by an improved county road that leads to the mine (fig. 1). The tract comprises an area of about 181 acres held by G. S. Stiner of Sharps Chapel, Tenn.; it is now under option to the Universal-Exploration Co. of Jefferson City, Tenn.The Bunch Hollow property, about 5 miles northeast of the Stiller prospect, was also studied by the Federal Geological Survey previous to being;Visited by Bureau of Mines engineers in August 1944. It is reached by traveling north from Maynardsville, Tenn., on State Road 33 about 13 miles, thence northwest by county road 6 miles to the property (fig. 1). The last 3 miles of the county road are in poor repair but are passable during the entire year. The property comprises an area of approximately 300 acres and is held by the imperial Mining Co., Pressman's Home, Tenn.Few reliable data are available as to the history of the Stiner prospects themselves. However, the New Prospect mine, 1 mile west, has had a colorful past, This mine was opened in 1883 and was worked intermittently until 1918, by which time more than 65,000 tons of concentrates had been shipped. No further work was done until 1942, when the mine pillars were robbed and 1,900 tons of ore averaging 25 percent zinc was shipped to the New Jersey Zinc Co., Austinville, Va."

Apr 1, 1946

By Joseph A. Holmes

The perpetuation of the supply of anthracite coal in Pennsylvania is a national as well as a State problem. Any investigation that shows how larger percentages of this coal may be saved in mining, without excessive cost, and without dangerous subsidence of the overlying surface ground, has a national as well as a local interest. Messrs. Conner and Griffith, who conducted the investigations described in this report largely for the city of Scranton, are consulting engineers for the Bureau of Mines for investigations similar to those they have already made in connection with their Scranton work; and this report is published by the bureau in response to numerous requests, because of the fact that the information it contains will prove useful in the general solution of similar problems in many of the country's coal fields. A study of the accompanying maps will show that the city of Scranton is underlain by 11 separate beds of coal, varying in thick- ness from 2 to 24 feet. It is estimated that before mining opera- tions were begun these beds of coal contained underneath the present city limits of Scranton 600,000,000 tons of coal. The 27 collieries operating within the city limits, working independently of each other, had excavated and removed, up to March, 1911, an aggregate of 198,000,000 cubic yards of coal and accompanying rock, or 3,000,000 cubic yards more than the total amount of material excavated and to be excavated by the United States in constructing the Panama Canal. This fact illustrates something of the magnitude of the problem that the city of Scranton, with the aid of these engineers and of a special commission or advisory board, has undertaken to solve. The excavation has included 177,000,000 tons of coal and 44,000,000 tons of rock and accompanying refuse. This leaves about 420,000,000 tons of coal still to be removed. As a result of other investigations and of experience in adjacent anthracite mines, Messrs. Conner and Griffith and the advisory board of engineers have advised that, as far as may be necessary to prevent dangerous surface subsidence, the spaces remaining beneath the city of Scranton from the excavation of the above-described material should be filled with sand and other materials by flushing or other processes. This operation is expensive, but it is believed to be not beyond the reach of what is practicable, nor in excess of the value of the coal that may be removed and the amount of damages that may result from the caving in of the surface if such a plan is not carried out. No one realizes so fully as do the authors of this report the need of additional tests and other investigations before the data now pre- sented by them can be fully accepted as sufficient for all purposes in the solution of the problem; and it is expected that at some early date a more extensive series of similar tests can be made by the Bureau of Mines under the supervision of Messrs. Conner and Griffith on a larger scale and under a greater variety of conditions. The field examinations made for the Bureau of Mines by N. H. Darton, which are described briefly in a chapter of this bulletin and will be discussed at length in a bulletin to be published later, indicate the extent and distribution of the sands, gravels, and other materials in the Scranton-Wilkes-Barre district available for flushing purposes if further tests indicate their relative merits; and it is expected that the relative merits of these different materials will soon be tested under such conditions as will furnish the desired information.

Jan 1, 1912

By J. H. Perkins

The Bureau of Mines has conducted desorption work on fine coal particles at near atmospheric pressure. An apparatus Iris been developed that uses a capacitance manometer to measure desorption of methane from coal particles up to, 2 inches in diameter and pressures up to 1,000 psi. This will make it possible to duplicate the desorption process as it occurs in its natural underground environment.

Jan 1, 1969

By S. P. Kinney, A. C. Fieldner, S. H. Katz

"The regrettable death of James S. Cunningham, Foreman Miner, attached to Bureau of Mines Rescue Car No. 2, while wearing a half-hour type oxygen breathing apparatus in a gasoline storage tank at Trinidad, Colorado, raised the question as to the possibility of gasoline vapors permeating the rubberized fabric of the breathing bags of such apparatus.It is known that most gases and especially certain organic vapors permeate rubber, by solution or a similar process. The rubber becomes saturated with the gas and if a concentration of gas is maintained on one side of the rubber sheet it slowly gives off gas from the other side. It of course takes some time for the gas to diffuse through the rubber and the length of time before it reaches the other side is proportional to the thickness of the rubber. The amount of gas that passes through per unit of area in unit time increases with the concentration of gas and also varies with the structure and composition of the rubber.It has been suggested that the gasoline vapor could not have penetrated into the interior of an oxygen breathing bag because the pressure is greater on the inside, but this is not true as the process of permeation by solution in the rub¬ber is affected only by the difference in the partial pressures of gasoline vapor on the inside and outside of the bag. The positive oxygen pressure on the inside can only prevent the entrance of gasoline vapor through measurable holes, and has no effect on permeation by diffusion through the rubber.A sample of gasoline was obtained from the tank in which Cunningham met his death. Examination by Dr. E. W. Dean of the Petroleum Division of the Bureau of Mines gave the following results.This shows the gasoline to be heavy and typical of the gasolines sold throughout Colorado for motor fuel A. Salvus half hour oxygen apparatus was arranged with the breathing bag only in a gas tight box in which the space was kept saturated with the vapor of this gasoline. The main part of the apparatus was outside the box. Oxygen from the apparatus was breathed by a man in the usual manner. Gas samples were taken from the box at intervals to determine the concentration of gasoline vapor, also samples of the oxygen breathed were taken from a side tube in the mouthpiece. The room temperature was 75°F. The concentration of gasoline vapor in the box at the beginning of the test was 4.3%. The man breathing from the apparatus thought he detected gasoline in his oxygen in two minutes after starting the test. Analysis of the inspired oxygen at this time showed 0.03% gasoline vapor. The same man remained on the apparatus for 18 1/2 minutes without suffering any ill effects. His place vas then taken by another man who wore the apparatus until the oxygen was exhausted without noticing more than a trace of gasoline at any time. At the end of the test the inspired oxygen contained 0.07% gasoline vapor. The total time of test was 38 minutes."

Dec 1, 1919

By John J. Sammarco, Janet S. Flynt

This report (Independent Functional Safety Assessment Guidance 7.0) is the last in a nine-part series of recommendations and guidance addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment’s life cycle. Figure1 shows a safety framework containing these recommendations. The reports in this series address the various life cycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended for use by mining companies, original equipment manufacturers, and after-market suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction (Part 1).—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics (PE), and includes the benefits of implementing a system/software safety program. • 2.1 System Safety (Part 2) and 2.2 Software Safety (Part 3).—These reports draw heavily from International Electrotechnical Commission (IEC) standard IEC 61508 [IEC 1998a,b,c,d,e,f,g]and other standards. The scope is “surface and underground safety-related mining systems employing embedded, networked, and nonnetworked programmable electronics.” System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system’s safety. • 3.0 Safety File (Part 4).—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a “proof of safety” that the system and its operation meet the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full life cycle of the system, and provides administrative support for the safety program of the full system. • 4.0 Safety Assessment (Part 5).—The independent assessment of the safety file is addressed. It establishes consistent methods to determine the completeness and suitability of safety evidence and justifications. This assessment could be conducted by an independent third party. • Safety Framework Guidance.—It is intended to supplement the safety framework reports with guidance providing users with additional information. The purpose is to assist users in applying the concepts presented. In other words, the safety framework is what needs to be done and the guidance is how it can be done. The guidance information reinforces the concepts, describes various methodologies that can be used, and gives examples and references. It also gives information on the benefits and drawbacks of various methodologies. The guidance reports are not intended to promote a single methodology or to be an exhaustive treatment of the subject material. They provide information and references so that the user can more intelligently choose and implement the appropriate methodologies given the user’s application and capabilities. The guidance reports comprise parts 6 through 9 of the series and are listed below: [< 5.1 System Safety Guidance (Part 6).—This guidance supplements 2.1 System Safety. < 5.2 Software Safety Guidance (Part 7).—This guidance supplements 2.2 Software Safety. < 6.0 Safety File Guidance (Part 8).—This guidance supplements 3.0 Safety File. < 7.0 Independent Functional Safety Assessment Guidance (Part 9).—This guidance supplements 4.0 Independent Functional Safety Assessment.] [ ]

Jan 4, 2006

By John J. Sammarco

This report (Safety File Guidance 6.0) is the eighth in a nine-part series of recommendations and guidance addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment’s life cycle. Figure 1 shows a safety framework containing these recommendations. The reports in this series address the various life cycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended for use by mining companies, original equipment manufacturers, and aftermarket suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction (Part 1).—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics (PE), and includes the benefits of implementing a system/software safety program. • 2.1 System Safety (Part 2) and 2.2 Software Safety (Part 3).—These reports draw heavily from International Electrotechnical Commission (IEC) standard IEC 61508 [IEC 1998a,b,c,d,e,f,g]and other standards. The scope is “surface and underground safety-related mining systems employing embedded, networked, and nonnetworked programmable electronics.” System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system’s safety. • 3.0 Safety File (Part 4).—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a “proof of safety” that the system and its operation meet the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full life cycle of the system, and provides administrative support for the safety program of the full system. • 4.0 Safety Assessment (Part 5).—The independent assessment of the safety file is addressed. It establishes consistent methods to determine the completeness and suitability of safety evidence and justifications. This assessment could be conducted by an independent third party. • Safety Framework Guidance.—It is intended to supplement the safety framework reports with guidance providing users with additional information. The purpose is to assist users in applying the concepts presented. In other words, the safety framework is what needs to be done and the guidance is how it can be done. The guidance information reinforces the concepts, describes various methodologies that can be used, and gives examples and references. It also gives information on the benefits and drawbacks of various methodologies. The guidance reports are not intended to promote a single methodology or to be an exhaustive treatment of the subject material. They provide information and references so that the user can more intelligently choose and implement the appropriate methodologies given the user’s application and capabilities. The guidance reports comprise parts 6 through 9 of the series and are listed below: [5.1System Safety Guidance (Part 6).—This guidance supplements 2.1 System Safety. < 5.2 Software Safety Guidance (Part 7).—This guidance supplements 2.2 Software Safety. < 6.0 Safety File Guidance (Part 8).—This guidance supplements 3.0 Safety File. < 7.0 Independent Functional Safety Assessment Guidance (Part 9).—This guidance supplements 4.0 Independent Functional Safety Assessment.] [ ]

Jan 4, 2006

By Russell. Paul L.

"INTRODUCTION Preliminary reports by Bureau of Mines engineers 3/ and by the Federal Geological Survey 4/ suggested that exploration would discover substantial reserves of minable ore in the Contact mine, Grant County, New Mexico. During February and March 1943, a sampling program was conducted on this property under the direction of the author. This was art of a general survey of the manganese districts of southwestern New Mexico.In its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources, to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as practicable soon as after its conclusion. The Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocer, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. S. Dean, assistant director. With respect to this report, special acknowledgment is due to C. H. Johnson, district engineer for New Mexico, and E. D. Gardner, regional engineer, and his staff, of the Central Region of the Bureau of Mines at the time of this work in 1943; also to Kenworthy, metallurgist at the Rolla. Mo., Laboratory of the Bureau of Mines, for work on beneficietion of the ore, and Sherman K. Neuschel, geologist of the Federal Geological Survey, for assistance in interpreting geological data at the project."

Oct 1, 1946

By J. W. Montoya

The chemical, mineralogical, and physical properties of berylliferous tuff from Spor Mountain, Utah, were determined in laboratory research conducted by the Bureau of Mines. Two beryllium-bearing minerals--a hydrated form of bertrandite and a berylliferous saponite--were found to be present in the tuff. Each of the beryllium mineral forms predominated in samples from certain areas of the district. The possibility of practicably separating the beryllium minerals from the tuff by physical methods appears remote because of the complexity and nature of the mineral associations. Beryllium mineralization in the region occurs in a rhyolitic tuff usually overlaid by unaltered rhyolite. The beryllium is distributed erratically throughout the tuff in individual mineralized bodies. Many samples of mineralized tuff were examined and found to contain from 0.2 to 1.8 percent BeO. All samples contained a hydrated form of bertrandite that was nearly cryptocrystalline, whereas samples from one area also contained a berylliferous saponite of variable beryllium content. Neither mineral has been previously reported, although related bertrandite-like minerals have been found in the U.S.S.R. and berylliferous minerals of the montmorillonite group have been synthesized. Most of the minerals of the tuff are finely crystalline, intergrown, and have similar densities. The complexity and intimacy of the mineral associations, the difficulty of achieving effective mineral liberation, and the highly friable nature are characteristics that lead to the conviction that tuff of the type examined cannot be effectively concentrated by gravity, magnetic, electrostatic, attrition, washing, sizing, or flotation methods.

Jan 1, 1962

By John Gross

"Introduction.Southern Illinois and Kentucky are credited with approximately 90% of the fluorspar production of the United States. A small amount of high-grade acid, spar is obtained from the ore by band sorting; the greater part, however, is recovered by jigs and tables as gravel spar containing approximately 85% calcium fluoride. In the jigging and tabling operations, galena is recovered, and enough silica and calcite are removed to raise the calcium fluoride content of the gravel spar to 85%. However, the removal of silica and calcite results in a large loss of spar. With increasing depth in the mines, zinc sulphide, sphalerite, is encountered in increasing quantity and the removal of this has become a serious problem. While the sphalerite can be fairly well removed from the spar by present milling methods, a marketable zinc concentrate can not be made. The experiments described below were made on fluorspar ore from Southern Illinois, by the mining experiment station of the U. S. Bureau of Mines, at Rolla, Mo., in cooperation with the Missouri School of Mines and Metallurgy.The ore tested contained. 7.3% lead, 27.9% zinc, 35.7% calcium fluoride, 9.5% silica and 4.7%. calcite.Tests and Results. In some preliminary tests it was noticed that a portion of the finely crushed ore adhered strongly to the sample pans, and upon investigation it was found that the adhering material was practically clean spar. By utilizing this property of adhesion 46.8% of the spar was recovered as a product containing 98.3% calcium fluoride. This suggested the possibility of using electrostatic separation."

Jul 1, 1921

By R. V. Ramani, C. B. Manula, A. Owili-Eger

ANALYTICAL PRESSURE - VOLUME COMPUTATIONS FOR THE MINE PROTOTYPE A new coal mine is projected, with entrance by slope 1,500 feet long. Nine main entries will be standard for development, five as intake and four as return. One return shaft is planned near the slope bottom, and an intake shaft and portal are planned 5,000 feet north of the slope bottom. The slope will have an area of 150 square feet and a perimeter of 55 feet. A belt and supply track will be within the slope. The return shaft will be circular with a diameter of 18 feet and will be 500 feet deep with an escapeway. Two hundred feet of the shaft and 500 feet of the slope will be concrete lined. Select the fan to operate five units per shift and drive the 5,000 feet to a proposed new portal, using the slope for an intake. Two main splits are planned with the maximum of three units on any split. The amount of air desired at each unit is 25,000 c.f.m; a shop at the slope bottom will require 10,000 c.f.m. In the solution of this or any similar problem, the first step is to determine the resistance factors. CALCULATION OF R FACTORS Slope area = 150 sq. ft.; Perimeter = 55 feet; Length = 1,500 feet. The friction factor K must be established. Five hundred feet of the slope is smooth lined, moderately obstructed by belt; K = 35. The remaining 1000 feet is in sedimentary rock and moderately obstructed; K = 85.

Jan 1, 1975

By J. W. Horne, W. L. Finley, A. D. Bauer, D. W. Gould

"The Bureau of Mines and the State of Colorado are cooperating in an investigation of the oil shales of Colorado. in this report the yields and the results of analyses of the oil and, gas produced from a number of oil-shale samples from the principal deposits of Colorado and other oil-shale States, are compared with samples from Scotland and Australia, where the oil-shale industry has had its greatest commercial development, and also with a sample from Brazil *here extensive oil-shale deposits are found shale samples were not selected as being representative of the different deposits, but they illustrate the wide variation in the nature of the organic matter of different oil shales.A further study is being made of the chemical composition of the shale, distribution of nitrogen and sulphur. in the products, temperatures at which organic matter decomposes, and the results will be presented in subsequent Papers, With complete data available on the chemical composition of the shales, it may be possible to explain some of the differences in the nature of the products from the various shales,Most of the work described herein was done under the supervision of M. J. Gavin. L. C. Karrick, formerly of .the Boulder laboratory, assisted in the work and gave many valuable suggestions."

May 1, 1924

By Robert J. Anderson

"Introductory Statement.In founding any kind of castings, even with the best practice, scrap castings are produced because of rejections for certain defects. Casting los¬ses are a serious source of financial loss in iron and steel foundry practice as well as, in brass and bronze, but they are particularly serious in aluminum foundry work because of the high value of aluminum. The indications are that in many aluminum foundries in the United States, the casting losses are at times high, and in some plants they are entirely too high when compared with average practice. Of course, defective castings have a residual value for remelting, but if much machine work has been done on a casting before it is scraped, the labor costs alone may exceed the value of the metal and even that of the rough casting.In a foundry, the monetary losses incurred through the production of waster castings can be ascertained from calculations based upon adequate scrap-loss reports. Such reports, when properly kept and interpreted are a valuable aid in finding foundry costs, but they are primarily useful in diagnosing the causes for casting losses. Many aluminum foundries in the United States do not keep adequate records of strap losses; as a result the causes for defective castings can not be traced, nor preventative measures adopted. However, some of the large aluminum foundries keep excellent records, and it has been found that these involve little extra expense for clerical work. If a foundry man will study his daily production of defective and waster castings, he will be able to trace the causes or losses and then make such corrections in his plant practice as will effect a considerable reduction in these losses -- as much as 50.0 per tent in some foundries. If all the present casting losses of the United States could be reduced 50.0 per cent, by eliminating only the readily preventable defectives, a saving of several million dollars would accrue. In the aluminum-foundry industry alone, the saving would amount to about $600,000."

Apr 1, 1920

By J. A. Kost

Contract H0242013 was originally to evaluate through underground tests, water spray systems for controlling respirable dust at the face of a longwall plow. A number of difficulties were encountered which made such an evaluation impractical. The contract was modified to evaluate, in the BCR dust tunnel facility, the live factors believed to affect respirable dust levels. A 60-foot long; plow face mock-up was constructed in the dust tunnel, a facility with controlled airflow and dust concentration. Six types of nozzles were tested with the following parameters: two nozzle orientations, two levels of water pressure, two levels of airflow, and with and without simulated airflow through the gob. Of these factors, the most significant in reducing respirable dust levels was nozzle orientation, where the nozzle directed 45 degrees downstream resulted in 27 percent lower dust levels than those directed 45 degrees upstream (against the airflow). Following in order of effectiveness were the higher water pressure and the lower airflow. All nozzles tested resulted in similar dust reduction, i.e., the type of nozzle was the least significant factor.

Jan 1, 1979

By Lloyd A. Morley

Two methods are presented to determine the mechanical shaft torque as a function of time for an induction motor. The methods are based on the motor equivalent circuit and use as input variables of the motor terminal voltage, line current, input power, and power factor. One method uses all four variables and the other uses only voltage and current. The test data deals specifically with continuous miners, but the theory could be applied to other mining machines driven by multiple induction motors. Results are given for the tramming, maneuvering, cutting, and cutting with loading operations and are in the form of a minimum, a maximum, and an average of the shaft-torque time function. The theoretical development and computer implementation are discussed for both methods.

Jan 1, 1978

By D. B. Dow

The transportation of any commodity which is actually or potentially a source of fire or explosion, has been made safe, insofar as humanly possible, by rigid requirements as to inspection mechanical safety devices, and by printed labels. For the most part these precautions have been sufficient. This is evident when it is considered that in the thousands of instances in which commodities with a great fire risk have been transported, few disasters have occurred. This paper deals with the recent gasoline explosion which occurred at Memphis, Tennessee. At 7:50 a.m. January 24, 1921, vapors from a tan: car of gasoline became ignited and resulted in a blast that killed eleven people and badly injured nineteen others. Probably forty or fifty men, women, and children received slight injuries from falling debris or from burns. The explosion wrecked an oil plant, leveled a block of frame buildings, and broke window panes within a radius of five blocks.

Feb 1, 1921