Search Documents

By G. D. Jermain

Exploration of the Antimony Peak district by the Bureau of Mines was conducted under the authority of the Strategic Minerals Act of 1939. Antimony was one of the seven metals designated at that time as strategic by the Secretaries of War, Navy, and Interior upon advice of the Army and Navy Munitions Board. As a result of many field examinations, the Antimony Peak property was chosen as one of the most attractive for the possible development of emergency antimony reserves. Exploration by the Bureau of Mines began in November 1940 and was concluded in May 1941.

Jan 1, 1949

By Richard A. Winters

In 1987, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 334-acre Mountain Lakes Wilderness Study Area (OR-011-001) in order to evaluate its identified mineral resources. The study area is located in Klamath County about 15 miles northwest of Klamath Falls, Oregon, and is adjacent to the Mountain Lakes Wilderness. The area is underlain by Pliocene-age basaltic andesite. No mining districts are in the study area nor were any claims recorded or found. There are no oil and gas lease applications. There are no identified mineral resources in the study area. INTRODUCTION This report describes the USBM (U.S. Bureau of Mines) portion of a cooperative study with the USGS (U.S. Geological Survey) to evaluate mineral resources and potential of the Mountain Lakes WSA (Wilderness Study Area), at the request of the BLM (U.S. Bureau of Land Management). The USBM examines individual mines, prospects, claims, and mineralized zones, and evaluates identified mineral and energy resources. The USGS evaluates potential for undiscovered resources based on areal geological, geochemical, and geophysical surveys. Results of the investigations will be used to help determine the suitability of the WSA for inclusion into the National Wilderness Preservation System. Although the immediate goal of this and other USBM mineral surveys is to provide data for the President, Congress, government agencies, and the public for land-use decisions, the long-term objective is to ensure the Nation has an adequate and dependable supply of minerals at reasonable cost.

Jan 1, 1988

By T. T. Read

"Education is the one thing which is unanimously regarded as valuable. The growing complexity of modern life, with its intricate organization, the manifold kinds of mechanical equipment that are used, and the constantly growing, necessity for the speedy and accurate interchange of information and ideas, make education an asset that constantly increases in value. The number of things that may profitably be known has grown so large that the field of education has been divided, and attention is often directed to only those things that are most immediately valuable. Modern educational facilities are often directed to what may be called corrective, work; the, providing of people with information that they teed in the conduct of their daily lives, but which for various reasons they have not previously had facilities for acquiring. The value of special education in the industrial world has been so thoroughly demonstrated that far-seeing managers of mining enterprises are always interested in the educational facilities existing in the community where their work is carried on.The educational facilities of a modern community may be classified in several ways. They may be divided into;1. Facilities for general education, for the purpose of increasing the whole field of knowledge of the student.2. Facilities for special education, which are intended to remedy a specific defect, or to give proficiency in some special field. This may be divided as follows;a. Training for work, intended to fit an employee to adequately perform the task assigned to him, this ranges from brief instruction by a foreman or fellow-worker up to definite training courses in which the employee dose nothing but study for a period of several weeks or months, being paid during this period a wage that may range from a nominal amount up to practically full time salary. The student's educational preparation may already be fairly advanced. Some of the manufacturers of electric machinery maintain, a school similar to that just described for graduates of engineering colleges. In other cases the only pre-requisite may be a common school education, as in the schools for operators, maintained by the telephone companies."

Apr 1, 1920

By A. L. Engel

Included in the program of the Rare and Precious Metals Station, Metallurgical Division, Bureau of Mines at Reno, Nev., are investigations of treatment methods for ores representative of various mining districts throughout the country. The samples received for this work may come from areas only recently explored or from newly discovered ore deposits in older mining districts. The present investigation deals with a case of the latter type, the. ample having come from a section that has a past record of considerable precious. metals production. The application of current treatment methods to this type of ore seems to offer excellent possibilities of satisfactory economic results. Definite identification of the silver mineral in this ore asthe chloride cerargyrite, AgCl, adds considerable interest to, the investigation, as in many cases where silver occurs in comparatively small amounts in an ore it is not possible to identify the particular mineral carrying the silver or else it is contained in or combined with other more common minerals. Cerargyrite is the "horn silver" of the bananza period and is mentioned in many accounts of pioneer mining of high-grade ores The occurrence of this mineral in finely disseminated form it a low-grade ore is believed to be unusual. The sample investigated was obtained from the' Bullfrog District neat Beatty, southwest Nye County, Nevada. The ore contained 16.7 ounces of silver per ton of ore, 0.007 ounce gold, and 0.32 percent copper in a silicious gangue, with accessory minerals, including iron oxides and scorodite; the hydrous iron arsenate.

Jan 1, 1949

By J. C. LaScola

Development of methanometers and anemometers for underground use in coal mines is reviewed. The first semicontinuous recording methanometer was developed in 1961 in West Germany. The Bureau of Mines developed an instrument using; pellesters that was a continuous recording methanometer. Expansion of freon gas created a vacuum which pulled the methane-air mixture through a tube to an electrically heated, catalyst-impregnated pellester where the mixture was burned. The National Coal Board of England developed a continuous recording methanometer based on the principle of the Davy flame safety lamp. A thermo-pile was used to sense the hurt output of the flame. Finally the Bureau of Mines improved its methanometer by eliminating the freon gas and using a diffuser head to a monitor methane-air mixtures. Development of recording anemometers proceeded from the use of a photo¬cell and light source to sense rotation of the Biram-type anemometer blades to the use of a Hall detector to sense, rotation by measurement of electromagnetic pulses.

Jan 1, 1969

By A. J. Barry

Five makes of expansion-type shells and two types of bolts (mild-steel and high-strength) were used in 30 tests made in sandstone and shale roof, The results show that the anchorage obtained in both the sandstone and shale were stronger than either type of bolt. That is, the yield loads of both bolt types were exceeded before excessive anchor slip occurred. A relationship for evaluating the anchorage effectiveness of 3/8-inch-diameter, expansion-type bolts is presented. A comparison of test results indicates that the anchorage effectiveness of 5/8-inch- and 3/4-inch-diameter expansion-type bolts did not differ appreciably.

Jan 1, 1957

By John E. Rourke, O&apos

A survey of existing and developing field permeability test methods was conducted in order to identify and specify capable methods to be used in feasibility investigations or performance monitoring for in situ leaching of ore deposits. Geologic settings of leachable deposits are discussed, as well as representative techniques used for the in situ leaching operation. Subsurface investigation techniques including drilling, core recovery, and down-hole inspection methods relevant to field permeability investigations are discussed. Field experience is examined and capable field permeability test methods are identified. Specifications for test borehole preparation, test performance. and methods of analysis are given. The test methods are comparatively rated in a matrix with respect to costs ease of use, and data effectiveness' for a broad range of conditions. Well Pump and Packer test methods receive high ratings. Recommendations are made for needed developments in field permeability test methods and a comprehensive bibliography is given.

Jan 1, 1977

By J. A. Zimrner, R. J. Tirnko

The roles of main mine fans in underground mines are to induce airflow and continuously re- move hazardous gases and dust. While most larger mines use multiple fans to accomplish these tasks, many smaller mines employ only a single fan. This paper concentrates on those mines having only one fan to provide ventilation needs. If this fan should cease to function, it is likely that methane concentrations will in- crease in some areas of the mine. As a safety precaution, Federal Regulations require that personnel must be- gin evacuating the mine within fifteen minutes after fan stoppage. Powered haulage can be used to transport workers to the mine portal as long as travel is through areas where hazardous levels of methane are not expected. To determine where methane will accumulate along haulageways during a fan stoppage, air samples must be taken at specific areas and analyzed for hazardous gases. During this study, procedures were developed for measuring methane levels along the haulegeways that are used to exit a mine following stoppage of the main mine fan. Methane levels were measured in four different mines at selected underground locations during four planned fan stoppages. In these mines the measurements taken only at the specified locations showed that, if workers had used electrically powered haulage to exit the mine following a fan stoppage, the methane accumulated along haulageways during fan stoppages would not have significantly increased the risk of an ignition.

To facilitate compliance with title 30 CFR 75.1001-1(b), which requires testing and calibrating of trolley line automatic circuit interrupting devices at intervals not to exceed six months. Approach Calibration of a circuit breaker ideally implies the passage of the expected fault current through the sensing circuit, and observing a successful circuit interruption at the preset level within a specified time. On trolley lines, the required current may be a few thousand amperes, with maximum duration well exceeding one-tenth of a second. Any method of obtaining this calibration current Involving the trolley wire can contribute to wire sagging and other permanent damage to the haul-age system due to the high energy dissipated during the test. Also, control to assure that exactly the required level and duration of current flow is obtained implies the use of equipment which is simply not available In the ordinary mine. Under a Bureau of Mines contract, a circuit to achieve the necessary calibration pulse was conceived and built. How It Works Two prototype units were fabricated and have been field tested by MSHA technical support engineers in under-ground mines. The equipment consists of an electronics Package 20 x 24 x 8 inches and weighing 93 pounds, including a side-mounted circuit breaker, with a set of 8 foot long detachable, AWG #4/0 leads with plier-type clamps. The total lead assembly weighs 21 pounds.

Jan 1, 1981

By Richard G. Burdick

This Bureau of Hines report describes an interface between a minicomputer and peripheral device, The logic used to develop the device is discussed briefly, after which the device is described in detail; complete construction and operational details are given. The report should aid both in duplicating this device and in designing similar devices for different uses.

Jan 1, 1975

By H. J. Fissan, G. Ananth, K. Rubow, V. Marple

"INTRODUCTION Over the past several years a new type of cascade impactor that utilizes small nozzle diameters (micro-orifice nozzles) has been under development (Kuhlmey et al., 1981; Marple et al., 1981). The small nozzle dimensions allow for particles to be collected as small as 0.024 µm aerodynamic diameter on the last stage of the impactor. To obtain a reasonable flow rate of 30 I min - i through the impactor, a large number of nozzles (up to 2000) are required per stage.Furthermore, by locating the nozzles of multi-nozzle stages in a prescribed manner (described in detail by Marple et al., 1981) and rotating the impaction plates relative to the nozzle plates, uniform deposits can be achieved on the impaction plates. As described by Marple et al. (1981), the advantages of a uniform deposit impactor over the conventional impactor that collects particles only beneath stationary nozzles are: (1) maximum use of the impaction substrate surface, reducing both particle bounce (if substrates are greased) and tare weights of the substrates (if particle mass is measured gravimetrically); (2) deposited particles can be analyzed for elemental composition by X-ray fluorescence (Dzubay and Rieke!, 1978); and (3) the pressure in the impactor can be kept relatively high compared to low pressure impactors that depend on a large slip correction to achieve small particle collection (some types of particles may evaporate at low pressures). The work described in this paper investigates two additional advantages of a uniform deposit impactor. These are: (1) the possibility of collecting two separate deposits at one time on one stage for two types of analysis techniques, and (2) the possibility of utilizing piezoelectric quartz crystal impaction plates more effectively by eliminating the deposit location sensitivity nature of the crystals (Schulze-Frohlich, 1981 ).MICRO-ORIFICE UNIFORM DEPOSIT IMPACTOR (MOUDI)A photograph of an eight-stage MOUDI is shown in Fig. 1. Each stage body of the impactor supports the impaction plate for the stage above and the nozzle plate for the stage below as shown in Fig. 2. By rotating alternate stage bodies, while holding the other stage bodies stationary, the impaction plates (or nozzle plates) will be rotated relative to the nozzle plates (or impaction plates).Rotation of the alternate stage bodies is achieved by gears on these bodies that mesh with gears on an electrically driven drive shaft of a rotating mechanism (Fig. 1 ). The alternate stage bodies are restrained from rotation by pins that rest on the drive shaft."

Mar 1, 1989

By Jon C. Volkwein

Dust concentrations inside and outside enclosed cabs on several types of mining machinery were measured by the Bureau of Mines. Results indicated that properly enclosed cabs can offer significant dust protection for machine operators. Recommendations for improvements in cab technologies were discussed.

Jan 1, 1979

By George S. Rice, Li C. Ilsley.

A remarkable explosion of fire-damp caused by a discharge of lightning at the new shaft at the Sitalpur coal mine, has been reported by the Chief Inspector of Mines of India, who gave the following details: "The explosion occurred during a thunderstorm, and the evidence showed that a flash of lightning had, to all .appaarances, passed down the shaft causing disruptive disohalges at certain points between the guides and the winding rope, Tending the latter at two places situated respectively 228 feet and 278 feet frem the surface, The distance between the winding rope and the side of the shaft was 6 feet 4 inohes, indicating a spark gap;of this width, and an intensity of discharge which could not fail to ignite the explosive mixture of gas and air known to be present in the shaft."

Feb 1, 1920

By B. W. Gandrud

In the summer of 1950, Bureau of Mines engineers visited a number of coal-preparation plants in western Europe and Great Britain to obtain information on European and British coal-cleaning and froth-flotation practices. In view of the growing importance of froth flotation as a process for cleaning fine sizes of coal, it was felt that such data and information would be of value in this country, for, although froth flotation has been adopted for use in a few of our plants, it has not as yet been employed as extensively as in British and European preparation plants. Many of the important coal beds in western Europe, especially in the Ruhr Valley of Germany and in the Dutch coal-mining region of Limburg, Netherlands, are very friable, with the result that the run-of-mine product contains a large proportion of the sizes too fine to be treated successfully by any other method than froth flotation. Furthermore, the relatively high cost of producing coal from these beds has for many years made it economically feasible and desirable to treat the fines by froth flotation, especially in the coking-coal fields.

Jan 1, 1951

By John P. Conway

This Bureau of Mines investigation was undertaken to determine the feasibility of lock-bolt support in Tertiary-gravel material. Pull tests were performed on five types of rock-bolt anchors to determine their optimum anchorage capacity. Four of these anchors are commercially available; the fifth, an explosive-anchor bolt, was developed by the Bureau of Mines. To increase anchorage capacity, epoxy grout was used with several of the commercial types of bolt. Tests showed that sufficient anchorage could be obtained by employing epoxy-resin grout with the commercially available wedge bolt, or by using the explosive-anchor bolt. Also estimated are bolt spacing and cost of a rock-bolt support system.

Jan 1, 1971

By D. T. Couillard

Video technology is becoming an important tool for many designers of industrial training programs. This report describes how trainers at the Minntac Mine, Mt. Iron, MN, have developed videocassettes of safe job procedures (SJP's) for training miners assigned to perform unfamiliar work tasks. All steps necessary for videocassette production, from idea to finished product, as well as the required equipment and prices, are listed and/or briefly explained. Minntac officials believe that the SJP videocassettes have contributed significantly to a reduction in mine accidents.

Jan 1, 1985

By Michael J. Pazuchanics, Thomas J. Fisher, John J. Sammarco, Jeffrey H. Welsh

This report (An Introduction to Safety) is the first in a nine-part series of recommendations addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment's life cycle. Figure 1 shows a safety framework containing these recommendations. The reports in this series address the various life cycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended for use by mining companies, original equipment manufacturers, and aftermarket suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction.—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics, and includes the benefits of implementing a system/software safety program. • 2.1 System Safety and 2.2 Software Safety.—These reports draw heavily from International Electrotechnical Commission (IEC) standard 61508 and other recognized standards. The scope is "surface and underground safety mining systems employing embedded, networked, and non-networked programmable electronics." System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system's safety. • 3.0 Safety File.—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a "proof of safety" that the system and its operation meets the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full life cycle of the system, and provides administrative support for the safety program of the full system. [ ]

Jan 4, 2001

By David C. Oyler

Three long horizontal holes were drilled from a directionally drilled surface hole at the Emerald Mine near Waynesburg, Pa. The purpose was to adapt the technique of directional drilling for use in draining methane from coalbeds. A 504-m (1,652-ft) long, 76-mm (3-in) diameter, circular arc pilot hole was drilled, using a downhole mud motor, to enter the Pittsburgh coalbed at a vertical depth of 305 m (1,000 ft). The hole was reamed to 222 mm (8-3/4 in) and was cased to a measured depth of 486 m (1,595 ft). Three 76-mm (3-in) diameter horizontal drainage holes were then drilled, totaling 2,909 m (9,544 ft) of horizontal hole. Improvements in drilling methods increased the average drilling rate from 20.4 ill (67 ft) to 64.9 m (213 ft) per day. The cost of drilling the directional and horizontal holes (using a Government-owned drill rig) was $1,169,530, a figure inflated by inexperience and by delays caused by lost-circulation problems and fishing operations. An estimated total drilling cost of $960,000 (including rental of a drill rig) for an improved system, was determined by a detailed cost analysis. Initial gas and water production from November 1979 through May 1980 was low because of caving of the horizontal holes drilled in shale near the bottom of the casing.

Jan 1, 1982

By Michael R. Yenchek

The U.S. Bureau of Mines investigated the operational characteristics of spliced portable power cables. This research had a dual purpose: (1) to determine the thermal and mechanical performance of repaired trailing cables and compare them with undamaged cables and (2) to gauge the impact of long-term, localized heating on the insulating and jacketing materials contained in cable splice kits accepted or approved by the Mine Safety and Health Administration. The ranges of splice joint resistance and tensile breaking strength were determined from laboratory measurements. The choice of crimping tools affected the strength of the splice under tension. Thermal profiles of energized spliced cables were constructed, which showed that spliced conductor joints operated 5 to 20°C hotter than the intact cable at rated currents. Accelerated life tests of thermally aged samples of splice kit insulation and jacket materials confirmed a deficiency in the thermal rating of the insulating tape. The recommendations in this report may be utilized to revise splice kit design, splice kit approval criteria, and trailing cable loading guidelines. Characterizing the thermal operating limits of spliced trailing cables may help to minimize the associated risks from explosions, fires, personnel burns, and shock.

Jan 1, 2010

By John C. Machisak

THIS INFORMATION CIRCULAR contains 1956 and 1957 injury experience and employment data for metal mines in the United States and Alaska. Unlike previous publications, this report covers only metal mining and contains statistical data on injuries and employment pertinent to metal mines and mills reporting voluntarily to the Bureau of Mines on an annual basis. Injury and employment data for the nonmetal industries, which from 1911 through 1955 were published in the same series as the metal industries, for the first time will be published separately as an information circular entitled "Injury Experience in the Nonmetal Industries, 1956 and 1957." The Bureau of Mines is authorized to make requests for injury and employment data, and the information submitted by operators of metal mines and mills is a step forward in promoting safety in the metal-mining industry. Every effort has been made to make this coverage as complete as possible.

Jan 1, 1960