Search Documents

By K. C. Dean

A semiquantitative test for the presence and identification of cesium and rubidium in rocks, clays, and mineral waters has been developed by the Bureau of Mines. The test can be used in the field, as a guide for the prospector, geologist, or mining engineer engaged in location or development [w]ork. It comprises two simple spot tests of a solution prepared from the [m]ineral sample. Phosphomolybdic acid, added to a drop of the test solution, [d]etects cesium, rubidium, and potassium in quantities as low as 60 parts per [m]illion. Silicomolybdic acid, added to a second drop of test solution, enables the operator to distinguish between cesium and/or rubidium and potassium. Test procedures, equipment requirements, and limitations of the method are described in this report. Cesium and rubidium were discovered in 1860 and 1861 by Bunsen and Kirchhoff with a spectroscope. The elements usually occur together, particularly in granite and granitic pegmatites. Rubidium does not occur as an essential constituent of any known mineral, yet it is found as a minor element in so many minerals that rubidium is 16th in abundance in the earth's crust. Cesium, which ranks as the 37th most abundant element, is the principal component of pollucite and a minor element in a wide variety of minerals.

Jan 1, 1960

By Karl C. Dean

The Bureau of Mines stabilized 10 acres of windblown copper mill tailings at McGill, Nev., by a combination chemical-vegetative procedure. Legumes, winter wheat, wheat-grasses, and wild rye were seeded, and the area was subsequently sprayed with a resinous adhesive chemical to stabilize the sands until the vegetation could grow. During the year since treatment, the area has been well stabilized against wind erosion. The established vegetation appears to be capable of self-perpetuation and renewal without irrigation. The cost of stabilizing the area was $135.50 per acre.

Jan 1, 1969

Researchers with the National Institute for Occupational Safety and Health (NIOSH) have developed a training module to educate both new, inexperienced miners as well as veterans on important issues related to self-rescue and escape procedures. These include: (1) physical and environmental conditions that can be encountered in a mine after a major explosion, (2) knowledge of emergency meeting locations and escape routes, (3) the importance of using self-rescuers, even in seemingly clear air, to keep the lungs isolated from contaminants, and (4) why miners should not go off to look for others who are missing. In addition, the module may stimulate miners to think about and discuss mine explosions and the devastating effects of such an event.

May 1, 2009

By Spencer P. Howell, Munroem Charles E.

"Introduction;As in the case of TNT previously presented*, this report presents the results of an investigation to discover the safest and best way of utilizing picric acid for industrial blasting purposes. It describes the physical and chemical properties of this explosive, gives precautions to be observed in handling, packing, preparation of cartridges, and holes, presents the results of field tests in blasting stumps and bowlders, and compares the results with those obtained from dynamite.The investigations reported herein were undertaken and this paper has been prepared, solely to aid in the salvage of the surplus picric acid accumulated for war uses and released by the declaration of the armistice. No funds were available nor have any been appropriated with which to defray the expense of converting this picric acid into any other form or to prepare any explosive mixture from it. The sole problem was to find appropriate uses for this military picric acid in existing needs and to show that it can be efficiently used in carrying out essential civil projects.It is not intended by this publication to promote the use of picric acid as an industrial explosive further than is necessary for the proper utilization of this surplus. On the contrary, the authors believe that picric acid by itself is unlikely to come into general use as an industrial explosive, chiefly because of its cost but also as shown by the clouds of smoke it emits on explosion and the nature of the reactions it undergoes because we do not obtain from it its highest efficiency. As demonstrated in its previous use in Joveite, better results and higher efficiencies may be obtained by mixing picric acid in proper proportions with sodium nitrate or ammonium nitrate, to more completely oxidize the picric acid, and another nitrosubstitution compound, such as nitronaphthalenes, with which do desensitize and waterproof the composition formed. By such admixture not only may the energy resident in the picric acid, be more fully utilized but the cost of the resulting blasting explosive should be much less than that of picric acid."

Apr 1, 1921

By Louis C. Brichta

The Rush Creek district of Marion County, Ark., has had a more or less continuous record of zinc production over the past 40 years. The ore has come from many small mines working on oxidized and semi-oxidized deposits found in the Everton formation where that formation forms the present surface rock. Prospecting has been restricted to the hillsides above the creek levels, the actual ore outcrops being the guides. Little attention has been paid the possible sulfide zones. In August 1942, the United States Geological Survey and the Bureau of Mines recommended exploration of the Powell and Cotter formations, which underlie the Everton, for which purpose the Survey had previously located 18 proposed drill-hole sites in geological structures that seemed favorable to are deposition.

Jan 1, 1949

By Jonisha P. Pollard

In restricted vertical working heights such as low-seam coal mines, workers are forced to assume kneeling or squatting postures to perform work. These postures are associated with increased risks for the development of significant knee pathologies such as meniscal tears and osteoarthritis [1,2]. Previous research has shown an increased applied knee flexion moment when kneeling in high flexion [3]. However, these models have been applied to flexion up to 140° which neglects contact between the thigh and calf which occurs beyond 140°. In addition to thigh-calf contact, when kneeling near full flexion there may be additional contact between the heel and gluteal muscles. To the author?s knowledge, heel-gluteus contact has not been previously investigated, but thigh-calf contact has received some attention. Zelle (2007) reported thigh-calf contact forces up to 30% bodyweight (BW) [4]. Zelle (2009) reported decreased knee forces when accounting for thigh-calf contact [5]. Caruntu (2003) reported erroneous force and moment estimations when thigh-calf contact was neglected from models to determine muscle and ligament forces [6]. In this study thigh-calf and heel-gluteus contact forces were quantified to determine their effect on the externally applied flexion moment in high flexion.

Jan 1, 2009

This is an audience, I know, that shares my interest in a subject that is currently getting a lot of attention -the tendency of our Nation to draw increasingly on overseas supplies of certain mineral commodities, and proportionately less on domestic sources for these minerals. That we do obtain substantial quantities of some essential minerals from abroad is easy to demonstrate. That we will continue to do so in the foreseeable future is not in doubt. Uncertainty begins, however, when we try to interpret the significance of these facts. As with many phenomena, their meaning is open to a variety of interpretations.

Jan 1, 1980

By H. B. Brunot

One of the many difficult problems that confront the present day coal-mine operator is the safeguarding of his employees and property from disasters such as fires, explosions, squeezes, and inundations. Those operators having gaseous or ev en dusty mines have a double responsibility resting upon them in this respect. The introduction of electrical machinery and appera tus in mining operations has been very rapid, and at the present time it is difficult to mention any kind of mining work in which electrical machinery is not used. This extended introduc- tion of electrical equipment has added not a little to the mine operators' safety problem, and it is the desire of the United States Bureau of Mines to aid the mine operator, and the inspection departments having jurisdiction, in solving their electrical safety problems. With this idea in mind, the Bureau has prepared and published schedules setting forth the qualities it considers essential to the safety of various classes of mining equipment, and the conditions under which it will test and give the stamp of its approval to satisfactory designs. Portable electric lamps of the permissible* type are almost universally used in gaseous mines, but the use of permissible electrical machinery has not been so widespread. Until recently the Bureau had issued approvals for only one class. of machinery involving the use of electric motors that is, permissible coal- cutting machines. However, the day is undoubtedly not far distant when the operator, who so desires, will be able to obtain a permissible room hoist, pump, or coal- loading outfit. During the year 1921 the first of a growing list of storage-battery locomotive approvals was granted by the Bureau, and it is with considerable satis- faction that the Bureau how announces the approval of a third class of motor equip- "merit- namely, slectric drills.

Jan 1, 1923

To develop a business case that promotes adoption of noise controls by reducing barriers to industry acceptance and enhancing drivers that foster their implementation. Background Over 75% of the U.S. mining workforce is exposed to hazardous noise, putting them at risk of noise-induced hearing loss (NIHL). Consequently, coal miners suffer high rates of hearing impairment that increase to 70%-90% by retirement age. To address the noise problem for coal miners, researchers from the National Institute for Occupational Safety and Health (NIOSH) first determined that the continuous mining machine (CMM) ranked first among machines associated with reported coal noise overexposures. Further studies found that most CMM noise is generated by three component systems on the machine: dust collection, cutting, and conveying. Of these systems, the on-board chain conveyor was found to be a dominant noise source. Noise generated by the conveying system was addressed through the development of a urethane-coated flight bar chain. The coated chain, shown in Figure 1, has demonstrated an 8-hour time-weighted average (TWA) reduction of operator exposure by 3 dB(A). It has since been accepted by the Mine Safety and Health Administration (MSHA) as a "technologically achievable" noise control for CMM operators who are exposed to noise that exceeds the MSHA permissible exposure level. Having demonstrated the noise reduction performance of the coated chain, NIOSH has assembled information into a business case that can be used by operations considering adopting the chain at their worksite.

Dec 1, 2009

By N. A. Gokcen

This Bureau of Mines report reviews and summarizes recent studies of the rates of chlorination of aluminous resources with CO and C12 mixtures with and without COC12. No reaction mechanism could be obtained from the existing results; however, diffusional barriers in the gas and solid layers probably control the chlorination rate in thermogravimetric experiments. Fluidized beds of particles smaller than 0.1 mm appeared to show very little solid layer diffusional barrier. For optimum chlorination the particle size should probably be less than 8 mm, the calcination temperature approximately 700° C, and the chlorination temperature from 650° to 750° C. Relatively rapid chlorination with COC12 in thermogravimetric experiments was attributed partly to the simultaneous supply of reductant and chlorinator by one gas to the sample reaction site. Comparable results for chlorination of fluidized beds with COC12 are not available. Equimolar mixtures of CO and C12 produced the optimum rate of reaction. Addition to the calcine of 10 to 20 wt-pct NaCl accelerated the rate of chlorination, and addition of SiC14 to the gas mixture decreased the rate of chlorination of SiO2 drastically, but at the expense of chlorination of significant fractions of Al2O3. Further research in various areas is suggested.

Jan 1, 1983

By Willis Beckering

The Bureau of Mines designed a cell having four variable compartments in series to facilitate analysis of multicomponent mixtures. Use of the cell considerably decreases the time required for differential absorption analyses. A solution of a major component is placed in each compartment, and the light absorbed by each of these components is varied by increasing or decreasing the path length of the appropriate cell. Simple calculations then establish the amount of the component present. In analyzing unknown mixtures, compensation is made for compounds known to be present, and the differential spectrum representing components not accounted for is recorded and analyzed.

Jan 1, 1966

By H. A. Schrecengost, H. R. Gil, Alfred Clarkson, E. H. McCleary

Much has been written and many discussions have been held concerning the prevention of accidents in coal mines , and considerable progress has been made in eliminating hazards to the health and safety of underground workmen . Although much progress has been made in the reduction of injury rates in the Pennsylvania anthracite field , the injury rates for the anthracite mines of Pennsylvania are generally higher than the average for coal mines in the United States as a whole , because the mining conditions , including the safety problems , in the Pennsylvania anthracite fields are more complex than in other coal fields of the United States . Several factors contribute to this extremely difficult problem , among which are : Multiple - vein mining , steeply pitching measures , folds or faults , hard smooth floors underneath the veins , and the remining or reclaiming of pillars in severely crushed , broken ground . In the early days of the Pennsylvania anthracite industry , only the more productive veins were mined , and this resulted in bypassing those veins that were relatively thin and those containing considerable proportions of impurities . However , the development of modern coal - preparation equipment , improved marketing conditions , and the adoption of mechanical equipment , such as the various types of conveyors and scraper loaders , have made possible the recovery of the thinner and poorer veins . Furthermore , in the early days , little or no attempt was made to recover the coal pillars , usually owing to the great amount of virgin coal available . Consequently , much of the anthracite produced within the last few years has been recovered by second and third mining and frequently by fourth mining - in areas where operations had been suspended for many years . In such areas , the coal veins and intervening strata are usually crushed as the result of gradual subsidence , which intensifies the hazards incidental to roof control , haulage , ventilation , and mine gases . Moreover , the use of coal - cutting equipment is not practicable in most anthracite mines because of. the inclination of the veins and because , in crushed -ground areas , the faces must be advanced slowly and for short distances at a time to permit the erection of timber sets and the placing of forepoles to support the roof and sides . Thus , the slow process of mining brought about by these conditions has resulted in the production of only 0.424 ton of anthracite for each man- hour worked , as compared with 0.753 ton? for each man - hour worked at other coal mines in the United States . A summary contained in Bulletin 462,8/ a publication of the Federal Bureau of Mines , reveals that the rate of fatal injuries in the Pennsylvania anthracite industry was improved from 13.47 deaths per million tons produced in 1870 to 3.88 deaths per million tons mined in 1942. During the period March 16 , 1942 to January 1 , 1947 , the fatality rate was reduced from 3.88 to 2.87 deaths for each million tons mined . On the million man-hour basis , the rate of fatal injuries was reduced from 1.643 to 1.130 and the nonfatalinjury rate was lowered from 119.01 to 83.12 during the same period . The improvements made in both the fatal- and nonfatal - injury rates have required the cooperation of the workmen , the mining companies , and the State and Federal inspection departments . Many individual mines and companies have achieved commendable safety records which contributed greatly to the over - all average for the industry , particularly during the 1942-47 period . One of the most outstanding of these is the Continental mine of the Continental -Archbald Coal Co. , a member of the Moffat Co. Interests .

Jun 1, 1948

By A. D. Garman

This paper presents one of a series of digests of foreign mining legislation and court decisions which is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries . This interpretation of the laws of Haiti has been prepared from the best available information in Washington, but is released subject to correction and amplification , if necessary , by the proper American diplomatic and consular officers to whom it is being referred through the courtesy of the Department of State .

Sep 1, 1930

By Gerald T. Homce

A system capable of monitoring a mine electrical power system to detect incipient electrical component failure could significantly improve power system safety and availability. The U.S. Bureau of Mines funded a contract with The Pennsylvania State University (Penn State) to establish the theoretical and technical framework for such a system. This report briefly outlines the contract, reviewing related Bureau and Penn State work prior to its award, and describes support work carried out by the Bureau. The main focus of the report is on research efforts by Penn State and subsequent results. An existing algorithm for incipient-failure detection and classification was studied, and recommendations are made to improve its performance. In addition, mathematical models of cable-connected motor systems and deteriorating motors were developed and implemented on computers. These models and laboratory tests were used to study and document relationships between component deterioration and electrical terminal effects. The project was supported by the U.S. Navy and the nature of its interest in the application of failure prediction techniques is also included.

Jan 1, 1989

By J. W. Paul

A superintendent is one who has the oversight and charge of some organiza- tion or enterprise, with porer of direction. The superintendent of a coal mine is the official who is in general charge of conducting the operation of the nine for the purpose of producing coal; he is accountable to his superiors for all matters that relate to the cost of production and safety in operation, ed under him are all the underground officials and other personnel making up the mine organization. The responsibility of the superintendent covers all the principal phases of mining, purchases of materials, issuance of supplies, accounting, and upkeep of the property and equipriont. In a broad sense, the superintendent must view his job as embraced under four gneral heads: (1) Construction, (2) instruction, (3) supervision; and (4) discipline. The degree of efficiency with which each of these phases of his work is conducted is a measure of the safety factor which the superintendent injects into his job. Injury to workmen and damage to property may be due to neglect of one of these general headings; as for example in the collapse of a scaffold there has been faulty construction which may be found upon investigation to have been the result of faulty instruction or lack of instruction. It may be that the condition of the scaffold was not ascertained in advance of its collapse through faulty supervision, or the discipline of the workmen had been neglected.

Sep 1, 1930

By X. Shi, V. Vallyathan, N. S. Dalai

"Electron spin resonance (ESR) measurements show that grinding of quartz particles in air produces silicon-based (Si- and SiO-) radicals which decay with aging in air. ESR spin trapping measurements provide evidence for the generation of hydroxyl and possibly superoxide radicals from a suspension of fresh quartz particles. The hydroxyl radical generation potential of the fresh quartz particles decreases on storing in ambient air and on the addition of catalase, superoxide dismutase, desferoxamine, or DMSO. Silica-induced lipid peroxidation also decreases on storing the fresh particles in ambient air. These findings suggest that oxygenated radicals play a role in the biochemical mechanism of pneumoconiosis in general and acute silicosis in particular.INTRODUCTIONThis communication summarizes our electron spin resonance (ESR) investigation of the formation of oxygenated radicals by freshly crushed quartz particles in a cell-free aqueous medium, and its potential role in the biochemical mechanism of acute silicosis. This study was undertaken because the mechanisms by which the quartz particles exert their toxic action on cells and the process(es) by which these actions progress to fibrogenesis are still not well understood. 1-3 It is generally believed, however, that the action of quartz particles on the cell membrane is the starting point of the silicotic process. 1,4 Since the first step must involve surface reactions, characterization of the chemical structure of the surface of quartz particles has been the subject of several recent studies!-' For example, we reported that mechanical crushing of quartz under normal atmosphere generates silicon-based (Si• and SiO•) radicals which decay with time, and that these radicals are associated with a higher cytotoxicity of fresh quartz dust as compared to that of an aged dust from the same stock. 6,8 Independently Fubini and coworkers' have also reported on the formation of Si• and SiO• -type of radicals from quartz particles crushed under atmospheric conditions. Gulumian and van Wyk9 have reported that quartz particles react with hydrogen peroxide (H202) to generate hydroxyl (•OH) radicals. These authors9 suggested that this process might contribute to quartz's pathogenicity but the mechanism of the -OH radical formation was not clarified. Earlier, Gabor and Anca10 had suggested that the cytotoxicity of quartz particles might be associated with the generation of some factor or factors possessing the properties of a free radical and hence capable of promoting the peroxidative chain cleavage of polyunsaturated fatty acid moieties of the phospholipids in the cell membrane. More recently, Weitzman and Graceffa 11 reported that asbestos is able to catalyze the generation of -OH radicals from H2O2. Their later work12 indicated that lipid peroxidation might be one of the mechanisms of tissue injury by asbestos."

Jan 1, 1989

By Elaine T. Cullen

Safety training materials appropriate for specific underground noncoal operations in the United States are often outdated or nonexistent. The Spokane Research Laboratory (SRL) of the National Institute for Occupational Safety and H ealth has developed several new training tools, including three videos on common underground activities, software that will allow trainers to create a virtual training mine using their own mine map, and toolbox training materials. SRL is working closely with industry in the development of these tools. Teams of safety professionals are involved in the early stages, and actual mines and miners are involved throughout the production phase. This presentation describes the development process and results of SRL’s safety training projects.

By L. C. IlsLey

The cool drills that have received the approved of the Bureau of Mines may be divided into three general classes: (1) Hand drills, small drills that are held in the hands or supported against the body while in use; (2) post drills, drills that are too heavy or powerful for hand operation and therefore require some mechanical mounting when in use; and (3) drilling machines. Besides these three classes, drilling equipment has been incorporated in the design n of a number of permissible coal-cutting machines, but such drills are considered an integral part of the cutting machine and are not given separate approval. The hand drills have been described in Report of Investigations 3363, which is cite of several papers that have been published dealing with miscellaneous types of permissible motor-driven mind equipment not covered in bulletins. The present paper describes post drills and drilling machines approved by the Bureau of Mines up to July 1, 1937.

Jan 1, 1938

By L. C. IlsLey

[The cool drills that have received the approval of the Bureau of Mines may be divided into three general classes: (1) Hand drills, small drills that are held in the hands or supported against the body while in use; (2) post drills, drills that are too heavy or powerful for hand operation and therefore require some mechanical mounting when in use; and. (3) drilling machines. Besides these three classes, drilling equipment has been incorporated in the design n of a number of permissible coal-cutting machines, but such drills are considered an integral part of the cutting machine and are not given separate approval. The hand drills have been described in Report of Investigations 3303, which is cite of several papers that have been published dealing with miscellaneous types of permissible motor-driven mind equipment not covered in bulletins. The present paper describes post drills and drilling machines approved by the Bureau of Mines up to July 1, 1937.]

Jan 1, 1938

By F. S. Crawford

Companies which have been engaged in safety work for a number of years are becoming increasingly aware of the fact that it is not enough to supply guards for various pieces of machinery and equipment and to supply safety inspection to see that rules are being carried out. Studies of many safety organizations have demonstrated that the accidents which could have been prevented by proper guards constitute only a small percentage of the total acci- dents, and amount to perhaps not more than 15 per cent. Evidently, if success is to be attained in preventing all accidents which it is humanly possible to prevent, a company must have the cooperation of every employee. Mining particularly presents probably the greatest hazards of any industry. Prevention of accidents. is made increasingly difficult because men often work alone, although generally in pairs, and only in the concentrated systems of mining do they usually work in groups of more than three or four. Supervision is difficult, therefore, and much reliance must be placed upon the individual workmen. In mining, as perhaps in no other occupation, it is of the greatest importance that individual workmen should receive continuous safety education. Within the last few years safety education has come to the front as one of the most important of accident-prevention measures, although it is true that its importance has been repeatedly stressed by the United States Bureau of Mines and other national safety organizations since the inception of the safety movement many years ago. A review of the safety educational methods of some companies in the Lake Superior district should be of interest. Perhaps better methods are in use in other parts of the country, but the methods shown have been instrumental in many cases in reducing the number of accidents. In one mine in the district whose methods are described the frequency of accidents has been reduced to zero within the last two years. A number of other mines in the district have recently gone into the class having no lost-time accidents for considerable periods of time. One company in the Lake Superior region, operating over 30 mines, succeeded during one month of 1930 in operating every mine without having a single accident which caused lost time beyond the day of the injury. Records like these are increasing in number, and while it is believed that they are the combined result of different means of safety activity, it is undoubtedly true that many of these results were obtained through safety educational methods.

Sep 1, 1931