Search Documents

Develop a means for analyzing seismic crosshole data to predict and monitor the Flow of leach solution during in situ mining. Background Improvements in predicting and monitoring in situ leach solution flow would aid in planning well field configurations. These improvements would also facilitate permit application by assuring regulatory agencies that leach solution would not escape from a well field undetected. Seismic tomography can detect fractured zones, which enables the prediction of probable flow paths, and it is a promising technique for monitoring leach solution injected above the water table. Tomographic analysis of crosshole seismic data provides a two-dimensional picture of the distribution of seismic velocities between the transmitter and receiver boreholes. The positions of fractured zones and of leach solution can then be inferred from the seismic velocities.

Jan 1, 1989

By B. J. Scheiner

Carbonaceous gold-bearing ores of the type that occur in north-central and northeastern Nevada were investigated by the Bureau of Mines as part of its Heavy Metals Program. Specific objectives were to identify the carbon and organic compounds that prevent adequate gold recovery from the ore by cyanidation and to develop an economical process that would overcome the detrimental effect of the carbonaceous constituents. Activated carbon and long-chain organic compounds containing sulfur and nitrogen were found in the ore. Part of the material consisted of stable gold organic complexes. A mild oxidation technique that allowed gold extraction as high as 96 percent by subsequent cyanidation was developed. A variety of oxidants was shown to be effective in improving gold recovery, including chlorine and sodium hypochlorite (NaOC1). An electrolytic oxidation process was developed that was particularly advantageous from an economic and effectiveness standpoint.

Jan 1, 1971

By H. Carroll

An ozone detector was built and evaluated for its applicability in smog-chamber studies. The detection method is based on the reaction of ozone with ethylene and the measurement of resultant chemiluminescence. In the first phase of evaluation, the detector's response to ozone was studied as a function of several instrument parameters, and optimum conditions were defined for the maximum and most stable responses to ozone. In subsequent evaluations, the method was checked for sensitivity, precision, and interferences and was compared with two alternative methods. Results showed the chemiluminescence method to be acceptably sensitive and precise for smog-chamber studies and superior to the Mast ozone meter and KI (colorimetric 1 percent neutral-potassium iodide method) methods in that it is specific for ozone.

Jan 1, 1972

By D. G. Kesterke

Research was conducted to determine the feasibility of extracting elemental oxygen from silicate-bearing melts by high-temperature electrolysis. The method was based on a modification of existing processes for electrowinning metals from their oxides dissolved in molten halide systems. Electrolyses were performed at temperatures ranging from 1,050° to 1,250° C in boron nitride cells that incorporated a silicon carbide cathode and an iridium anode. The electrolytes contained volcanic scoria as the oxygen source, plus mixtures of BaF2 and LiF as fluxing agents. Cell gases containing almost 14 volume-percent oxygen were obtained. The average anode current efficiency for several experiments of extended duration was calculated to be 55 percent. Cell design and operating conditions are described, and some of the problems associated with the process are discussed.

Jan 1, 1971

Only limited work has been reported in the literature about the use of latex in soil. Unisol 91 2,3 (a 9:l oil-latex emulsion made b International Synthetic Rubber Company) and Phil1ips Petroset4 geotechnic emulsions are surface soil stabilizers which penetrate a maximum of two inches, but do not reduce permeability. Diamond Alkali 5 found that styrene-butadiene rubber latex as a one percent latex-soil mixture reduced permeability to 0.7 from 21 feet per year under a head of twenty feet of brine. We have found no literature reference for use of latex as sealant at depth in the soil, although asphalt has been applied at depth using civil engineering methods6,7. Most of the materials investigated as soil sealants in the present work were latexes, although some studies were also conducted with a variety of inorganic and organic chemicals. Of the latexes tested, most were rubber but a few were plastic, e.g. polyvinyl chloride. Sealants examined in this investigation are listed individually in Table I with supplier, code number, and other pertinent information. The materials consisted of the following general classes with additional details as indicated: 1.Anionic latexes: a. styrene-butadiene copolymers and terpolymers (SBR) b. butadiene-acrylonitrile copolymer (Paracrils®) c. polyvinyl chloride homopolymers and copolymers (WC) d. ethylene-propylene terpolymer e. vinyl acetate homopolymers and copolymers (VA) f. acrylics (acrylate copolymers) g. 2-chlorobutadiene homopolymer (chloroprene) (prepared specially as cationic material coagulated by soil). 2. Water Soluble polymers: a. polyvinyl ether b. methylcellulose c. polyethyleneimines d. polyacrylic acid homopolymer e. copolymers and terpolymers with acrylic acid types (water soluble as sodium or ammonium salts) f. alginates g. monomers (for polymerization in soil, e.g. acrylamide)

Jan 1, 1972

The instrumentation specification in the National Academy of Engineering (NAE) report of March, 1970, set forth some rather general guidelines that the seismic surface system should follow. The fact that there was no comparable equipment in existence at that time, and the need to produce a system from presently available equipment, was spelled out in that document. The features that the system should include were listed, and included: • Quick and simple deployment • Portability • Battery-powered operation • All-weather operation • Computational simplicity and speed • High reliability and long shelf-life • Dual service for location and communication • Adaptability to widely varying seismic velocities. topography, and geologic structures • Minimum maintenance • Capability of continuous operation for extended periods, and • Reasonable cost Since that report, there has been a substantial amount of field work addressing the trapped miner detection and location problem carried out by Westinghouse Corporation under contract with the Bureau of Mines. Two complete surface systems have been designed, built, and field tested and substantial documentation has been produced on the mine environment and background noise using these systems. These systems, built from off-the-shelf equipment, have been designed with maximum flexibility in mind in order to explore what con¬figuration a field unit should have.

Jan 1, 1974

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

A. 4 Illustrative Simulations The capabilities of the program are demonstrated by simulating various evacuation cases in different situations for a particular mine. The mine selected for the illustrative simulations is the mine I C' , as described in Section 2, chosen particularly because of availability of mine characteristic data and mine evacuation results for test drills. These evacuation results can be used to verify validity of the predictions made by the program A.4 1 Mine Characteristics A schematic diagram of the mine is shown in Figure 19. The figure shows all the major shafts, drifts, raises and stopes of the mine in the form of a network. There are four hoists, Hoist No. 1 and Hoist No. 2 are assumed to be single drum hoists and Hoists Nos. 3 and 4 form part of a double drum hoist, with Hoist No. 4 being the main hoist (master hoist) The positions of the 133 miners, typically working in a day shift of the mine, are also shown in the figure. The miners are identified by a miner number, and their total number on each level is chosen from the data on the fire drill simulated as Case No. 1 in the illustrative simulations.

Jan 1, 1976

By J. Roger Loebenstein

Demand for arsenic exceeded supply, and major domestic and foreign producers allocated available supplies to customers for the fourth consecutive year. Major demand for arsenic was about evenly divided between industrial chemicals and agricultural chemicals. Legislation and Government Programs.-Effective April 1, 1981, taxes were collected from companies producing and importing 42 chemicals and petroleum products designated as hazardous, The revenue was used to begin funding of the 5-year, $1.6 billion "superfund" being established under Public Law 96-510, the Comprehensive Environmental Response, Compensation, and Liability Act, designed to help clean up spills of hazardous substances throughout the United States. As hazardous chemicals, arsenic metal and arsenic trioxide were taxed at the rate of $4.45 and $3.41 per short ton, respectively.

Jan 1, 1982

By J. Roger Loebenstein

ASARCO Incorporated, the only domestic arsenic producer, terminated copper-smelting operations and the associated recovery of byproduct arsenic trioxide at Tacoma, W A. in 1985. It still shipped small quantities of trioxide from its remaining stocks in 1987. Imports for consumption of arsenic trioxide were slightly higher than in 1986. Domestic Data Coverage.-Shipments of small amounts of arsenic trioxide from remaining stocks by Asarco were reported voluntarily to the Bureau of Mines.

Jan 1, 1989

By Jack E. Fraley

Poor lubrication reduces the life of wire hoist ropes when they are used in corrosive environments. Although lubricants are added to ropes during the manufacturing process, these lubricants can deteriorate during use, and it is often necessary to add more lubricant to both the interior and exterior of the rope while it is in service. The U.S. Bureau of Mines evaluated the effectiveness of synthetic lubricants, using electromagnetic nondestructive testing (NDT) to measure deterioration in ropes while they were in service. For nonpressurized lubricant applications, synthetic lubricants appear superior to petroleum-based lubricants in their ability to penetrate to the interior of a rope. Therefore, the synthetics offer better wear and corrosion protection.

Jan 1, 1990

By Hillary W. St. Clair

The effective coefficient for rate of reduction of a sample of granular iron ore may be determined by passing the reducing gas through a bed of the are at constant flow rate and periodically analyzing the effluent gas, The method of analyzing the data is based on a mathematical model that takes into account the variation in composition of the gas and solids with time and position in the bed. A method is described for determining the value of the rate coefficient that gives best agreement between the observed and calculated analyses of the effluent gas.

Jan 1, 1967

By Fred Leighton

The Bureau of Mines monitored a rock-burst-prone pillar in a metallic ore vein, up to and through failure, to measure its reactions to increasing loads, as it was mined. Three parameters were monitored: the stress changes at chosen points within the pillar, the displacement characteristics of the drift above the pillar, and the micro-seismic activity in and around the pillar. In descending order of effectiveness, the microseismic technique, vibrating wire stress measurements, and displacement measurements reflected the pillar reactions, and all showed good correlation to one another. A major rock burst in the pillar, which destroyed about 100 feet of drift above the pillar, occurred at the end of this study. This burst was preceded by a large anomaly in the microseismic activity in the failure area.

Jan 1, 1982

By David J. MacDonald

Stability constants, that is, equilibrium constants for complex-formation reactions, have been determined by a titrimetric method for complexes formed by the transition metal ions Ni2+, Cu2+, Zn2+, and Cd2+ with the structurally analogous bidentate ligands N-ethylethylenediamine and 2-(ethylthio)-ethylamine. The sulfur containing ligand was found to be the weaker of the two chelating agents for each of the four metals. Absorption spectra of the individual complexes have been determined in order to calculate their crystal field stabilization energies. The combined results suggest a linear relation between free energy of chelation and ionic radius of the metal ion.

Jan 1, 1972

By F. N. Kissell

The Bureau of Mines has successfully used sulfur hexafluoride (SF6) as a tracer gas to measure mine air flows under conditions where conventional methods have failed. SF6 was employed experimentally to measure accurately recirculation of return into intake air caused by leakage through an old stoped area, to check for potential leakage from an adjacent mine, to trace 10,000 cfm of “lost” air from an intake airway, and to measure transit air time through uranium mines. It proved useful as a means of accurately measuring airflow volumes in airways of large cross section and very low flow velocity, and in determining the recirculation resulting from underground cooling plants.

Jan 1, 1974

Measure the leakage through individual crosscut stoppings quickly and economically so that the worst ones can be identified and repaired. (Typically 60 to 80% of the air supplied to a mine short circuits before reaching a working face.) Approach Most of the leakage through a permanent stop-ping is channeled through two windows in a temporary stopping, and air velocities through the windows are measured; leakage is determined from a formula. How It Works A temporary stopping made of plastic brattice is erected in the same cross cut as the permanent stopping, either upstream or downstream. The brattice is fastened to the roof, bottom, and ribs of the entry with spads. Normal leakage of brattice was allowed for in deriving formula, and does not effect results. For best accuracy the brattice and the stopping should be separated by a distance of one hydraulic diameter.

Jan 1, 1979

To develop a simple device for rapidly determining the shearing strength and angle of Internal friction of coal and rock in situ. Approach Use a portable, permissible, hydraulically operated device in boreholes as deep as 100 feet into the rib, floor, or roof of the mine. How it Works The device, called a Borehole Shear Strength Tester (BST), is inserted Into a 3-inch-diameter borehole to the desired depth, locked Into position, and activated to shear the rock or coal in the borehole walls. The normal and shear pressures exerted by the BST, which are recorded during the test, are used to calculate the shearing strength and the angle of internal friction. The BST consists of 3 main components and several minor components. Main components are: ? A shear head with 2 shear plates that bite into the rock when normal pressure is applied. ? A hollow hydraulic jack with RW drill rods that pull the shear head when shear pressure is applied. ? A console with a hand pump and two hydraulic gages to activate the device and to indicate the pressures that apply the normal and shear faces to the shearing plates.

Jan 1, 1981

By J. E. Emmerling

The Federal Bureau of Mines investigated dust suppression obtained with three different water-spray nozzle systems during underground continuous coal mining at the face. The nozzles were the "regular" nozzle normally used by the mine, and high-efficiency and low-efficiency nozzles selected on the basis of an airborne capture theory of respirable dust by spray drops. The high-efficiency nozzle used one-third less water than the others throughout the testing. Results depended on the type of cutting operation at the face. The sump-downshear operation appeared to involve a significant amount of capture of airborne respirable dust. The same amount of dust was measured when using the high-efficiency and regular nozzles. The dust levels when using the high-efficiency nozzle were about 20 pct less than those measured when using the low-efficiency nozzle. The sump-upshear operation seemed to involve a predominance of other aspects of dust suppression, such as impaction of spray drops onto the face. Compared with the downshear operation, there was a significant reduction in dust levels for a total face operation when using the regular nozzle; dust levels when using the regular nozzle were about 15 pct lower than those measured when using the high-efficiency nozzle.

Jan 1, 1975

By Kenneth J. Miller

The Bureau of Mines conducted an investigation to improve the flotation response of coals that are difficult to wash by froth flotation. A literature survey and experimentation showed that, for the most part, refractory coals can be floated with oily collectors and frothers. Collector reagent consumption can be minimized and the selectivity of the flotation enhanced by assuring adequate, but not prolonged, reagent conditioning. Where flotation selectivity is especially poor, two-stage rougher-cleaner flotation is recommended. It was concluded that a major problem with refractory coals is predicting when they will appear in a flotation circuit so that supplementary flotation collectors can be added. Coal losses due to variation in the floatability of the feed might be reduced if a nonpolar collector such as kerosine or fuel oil is used along with a frother as general coal flotation practice.

Jan 1, 1977

By T. R. Taubert, D. H. Carlson, J. H. Johnson

The U.S. Bureau of Mines and Michigan Technological University (MTU) are collaborating to develop an apparatus for measuring diesel tailpipe emissions in underground mines. A tailpipe emissions measurement apparatus (EMA) is described that dilutes diesel exhaust and measures the concentrations of diesel particulate matter (DPM), CO, CO, NO, and NO, at known dilution ratios. The EMA was evaluated by side-by-side comparison of its measurements with those by laboratory- grade instruments. Concentrations of CO and CO, measured by the EMA were usually within + 14 pct of concentrations measured by laboratory-grade instruments for CO and 220 pct for CO,. EMA- measured DPM concentrations were, on average, 29 pct lower than those measured by laboratory-grade instruments, with the differences being fairly consistent. The CO and CO, differences are related to the method of calculating the EMA's dilution ratio, and the difference in DPM concentrations is attributed to thermophoretic and/or condensation losses related to the EMA's unheated sample probe. Preliminary analysis of data obtained with a heated sampling probe and modifications in the sampling procedures have indicated reduced variability in DPM and in the calculated dilution ratios.

Jan 1, 1992

By Stephen W. Lambert, Michael A. Trevits

The Bureau of Mines examined the wellbore of a vertical gas drainage well in the Mary Lee coalbed to determine the results of specific completion procedures in coal. A jet-slotting tool was used to cut four vertical slots through the casing about 1 ft below the coalbed. Even though stimulation treatment pressure was excessive, hydraulically induced channels were contained entirely within the target coal zone. Sand-filled, induced channels were horizontal, inclined, and vertical, and were propagated in directions similar to bedding planes, rock joint, and coal cleat directions measured in the mine. Variable gas flow rates, recorded during the productive life of the well, were attributed to chronic downhole pump malfunction and the slotted casing below the production zone.

Jan 1, 1978