Search Documents

Improve the field-of-view into the front-right blind spot for drivers of large haulage trucks, thereby reducing the growing collision hazard in surface mines. Approach Reduce the glare problem found in the first generation fresnel lens blind area viewer design by eliminating the upward-looking section of the fresnel lens and adding a rear hood to reduce backlighting. How It Works The first generation blind area viewer was developed and in-mine tested as an aid to improved visibility for large haulage trucks. Other aids were improved left-and right-hand mirrors. Evaluations showed that a blind area viewer mounted on the right-front of the radiator deck was effective and was readily accepted by drivers. Nevertheless, because glare was a problem under certain conditions, a low-profile viewer was developed. Glare control louvers from the earlier design were kept and a backlighting glare control hood was added. The height of the hardware was reduced by eliminating the top three inches of the fresnel lens. This portion of the lens contained an upward-looking segment which originally was thought to be needed so the driver could see the horizon when he looked through the viewer and be better

Jan 1, 1982

By Lloyd A. Morley, Alan M. Christman

General Six open-pit metal mines, five copper and one molybdenum, were visited during the course of the research. Four were investigated twice, in summer and in winter, in order to determine the effects of seasonal variations In temperature and moisture upon the measured parameters, Permission to enter the fifth mine was received too late to make an examination during the summer months. The sixth mine was visited to confirm the results obtained from the other five and specifically, to observe how the project recommendations (as will be presented in this chapter) would apply to open-pit metal mines in general. Information gathered during the ten plant visits is sufficient to form an adequate data base for the report. A complete presentation of all field trip data is given in Appendix 1. Further, a detailed description of the electrical distribution and grounding practices at each mine is also contained there. Typical System. At a typical mine as shown schematically in Figure 62, one or more substations with resistance-grounded secondaries are employed to transform the incoming utility-voltage to the lower potential used by the mining machines, generally three-phase 4160 V. At this level, pit distribution is carried on overhead lines, supported by wooden poles, to supply switchhouses located in benches near the particular piece of equipment. A switchhouse is a small portable (often skid-mounted) structure at the termination of an overhead line which contains disconnect

Jan 1, 1976

By C. H. Schwartz

A thermal radiation probe was constructed and tested in pulverized-coal-fired furnaces. A rotatable sensing head on the side of a water-cooled probe permitted measurement of radiant flux within a 7.20 cone from any desired direction to a point within a furnace. A response curve for a corner-fired furnace showed radiant flux of 130,000 Btu per sq ft per hr, when viewing flame, and 60,000 Btu per sq ft per hr, when sensing wall reflection. Detailed drawings and fabrication procedure are given.

Jan 1, 1970

By M. A. Trevits, S. W. Lambert

In this Bureau of Mines investigation, production was monitored for 1 year at over 30 coalbed gas-drainage boreholes located in Alabama, Pennsylvania, and West Virginia. Results indicate that the quality of data gathered from such wells can be improved greatly if potential problems are anticipated and prevented in the early stages of well production. Major water-monitoring problems include solids buildup, freezing, the presence of gas in surface waterlines, and improper pumping interval settings. Such problems may be avoided by incorporating in the original well design waterline filters, sand screens, separator tanks, and systems to automatically control pumping intervals. Problems related to measurement of coalbed gas flow include large quantities of water vapor contained in the gas, especially during winter months; freezing and subsequent obstruction of flow; sudden, uncontrolled release of gas pressure; and solids buildup in metering equipment. The installation of commercially available items, such as filters, separators, and insulation, and the thoughtful application of a basic knowledge of coalbed gas reservoir characteristics will prevent most production-monitoring problems.

Jan 1, 1978

To rapidly limit and interrupt high dc fault currents with minimal arcing in the mine atmosphere. Approach Design a dc switching sys-tem which uses a pressurized, liquid metal-filled, change-of-state device combined with a conventional interrupter and commutating switch. Direct Current Interruption Switching and interruption of large direct currents imposes severe loads on fuses, contactors, and circuit breakers in mine power systems. This problem is much more pronounced with de than with ac because of the lack of a natural current zero in dc. Dc interruption is characterized by persistent arcing that can foul contact tips and con-tribute to interrupter failures. To reduce maintenance and prolong the service life of these units, a commercially viable dc switching system has been developed by the Bureau of Mines through a research contract with the University of Pittsburgh. This system rapidly limits and interrupts high fault currents when used in combination with conventional interrupters.

Jan 1, 1983

Reduce the dust exposure to the operator of a longwall shearer with a novel foam spray system. Approach Discharge foam through the nozzles of a shearer drum so that foam and coal are better mixed. How It Works Bureau of Mines research showed that two very important principles for successful application of foam are: (1) moisture distribution and (2) degree of mixing. Foam can distribute a given quantity of moisture much more evenly over a large surface area. Successful Bureau tests of foam for dust control always involve a high degree of mixing between the foam and the material, Mixing, permits a greater distribution of foam throughout the mined product. The most suitable location of foam application would be at the point where the dust is generated, before the dust becomes airborne. Foam nozzles located in the cutter drum (pick face foaming or ejecting foam through scroll sprays) will suppress dust close to its source.

Jan 1, 1989

By Connie S. Musulin

The Bureau of Mines conducted an experiment at Exxon Mineral Co.'s Buffalo Shaft Operation to determine the time required for radon concentrations to return to a base average after fan shutdowns. Shutdown times ranging from 5 min to 16 hr were evaluated. An equation was derived to calculate a ratio that determines the time required for the radon concentration to return to the average level that existed in the mine prior to shutdown. For fan shutdowns of 15 min or more, underground personnel should be evacuated to areas with natural downcast ventilation. For shutdowns of less than 1 hr, personnel should not return to the working area until the elapsed time is four times the shutdown, or until the working area is resampled and found safe. If the mine is not in production during weekends, the downcast fans can be turned off .from midnight Friday until 4 p.m. Sunday, and the radon daughter concentration should be below 1 WL throughout the mine by the start of the shift Monday. This fan shutdown would conserve energy and save the mining company an estimated $21,000 each year.

Jan 1, 1982

The U.S. Department of Labor?s Mine Safety and Health Administration (MSHA),through its winter alert program, warns U.S. mine operators and miners at underground coal mines of workplace hazards that can arise when the weather turns colder. MSHA records indicate that, historically, most explosions in underground coal mines occur during winter months. ?The changes in weather can increase the risk of fatal accidents,? says David G. Dye, Acting Assistant Secretary of Labor for Mine Safety and Health. ?Each miner and mine operator must take individual responsibility to eliminate the kinds of hazards that can cause fatal accidents in the workplace. Safety is not the other guy?s job?safety begins with you.? In fact, MSHA?s slogan for this year?s campaign is ?Winter Alert Starts Now and Safety Begins with YOU.? This message reminds miners and mine operators of the risks of colder weather and educates them about helping to reduce risks and hazards. ?Safety requires the joint effort of both management and labor,? Dye says. ?Everyone at the mine site must see safety as an individual value and act to ensure a safe working environment.?

Jan 1, 2006

Provide a low-maintenance, reliable means of generating bubbles and controlling bubble size for column flotation. Approach Commercial sparger systems used in flotation columns to process minerals provide only limited means of controlling the size of bubbles generated and the rate of air injection. Generally, these limitations are a detriment to flotation performance, particularly in recovering coarse or fine mineral particles. In addition, conventional bubble generation systems require frequent maintenance, often requiring shut-down of the column itself for repairs. To permit greater control of the bubble size generated in the flotation column and to eliminate the counter-productive problems associated with the operation of current air sparger systems, the Bureau of Mines investigated alternative methods for generating bubbles. Based on the investigation, an external bubble generation system was designed, developed, and laboratory and commercially tested.

Jan 1, 1987

Reduce mine worker dust exposure by capturing airborne coal and quartz dust generated by a continuous mining machine. Approach Install a water-powered scrubber system operating at 1,000 psi on the side of a continuous miner boom. Dusty air under the boom is drawn through the scrubber, and cleaned air is discharged into the face return. How It Works Most coal mines use exhaust face ventilation to send fresh air over the miner operator, and contaminated air behind the line curtain to the section return. The difficulty with exhaust face ventilation is that the line curtain should be within 10 feet of the face for maximum effectiveness. If the line curtain is not extended properly, or water sprays for dust control are poorly installed, dust rolls back toward the operator. A scrubber mounted on the mining machine will effectively reduce this dust rollback and the dust in the return airstream.

Jan 1, 1989

By J. K. Whyatt, B. G. White

Various methods of monitoring slip movements on bedding planes, as well as examination of rock burst damage in stopes, suggest that many rock bursts in the Lucky Friday Mine are closely associated with these movements. Slip displacements along bedding simultaneously reduce the physical dimensions of stopes and increase compressive stress along stope margins. Such changes, in turn, contribute directly to sudden failures of rock and cemented sandfill surrounding stopes. We believe that the reduction of rock burst hazards must be based on a clear understanding of the basic mechanisms involved. The current work emphasizes the mechanical role of wall rock movement and seismicity in generating conditions that promote rock burst damage. Based on our interpretations of these mechanisms, we briefly address several hypothetical practices that could influence rock burst hazards in similar mining situations. The overall goal of this research is to advance the NIOSH mission of improving the health and safety of the nation’s workers.

By F. M. Carlson

Comparisons are made between the results of the Buckley-Leverett and Kern solutions, which describe immiscible displacement of oil by gas in a linear system and the results obtained from a less restrictive numerical model. This model takes into account the effect of compressibility of the oil and gas and the effect of allowing changes in the amount of gas in solution in the oil. These effects are best exemplified by imposing large pressure drops across the system. With these large pressure drops, comparison of the model solution with the Buckley-Leverett solution reveals that the Buckley-Leverett solution provides estimates of recoveries at breakthrough of the gas that are too low. In contrast to the model, the Kern solution predicts breakthrough recoveries that are too high. A modification to the Kern solution is presented to facilitate more accurate predictions of recovery at gas breakthrough for gas injection at pressures higher than the saturation pressure of the oil.

Jan 1, 1974

Reduce the number of conveyor-related accidents in the mining industry by providing recommendations for effective operation of conveyor belt cleaning systems. The Problem Troughed belt conveyors provide effective, and efficient materials transport and their use has increased throughout the mining industry. Carryback, the spillage that accumulates under the belt, is a problem even with belt cleaning systems installed. Mining personnel are exposed to safety and health hazard; as they attempt to clean up this spillage. Approach To investigate the influence of metal-segmented-blade belt cleaners on the amount of carryback spillage, the. Bureau identified and tested the following parameters: (1) amount of pressure applied to the cleaner blades, (2) friction between the blades and conveyor belt, and (3) wear rates of different metal blades. The test parameters were quantified by recording the amount of carryback material passing the metal cleaner blade, and the weight loss of the blades. The data collected were used to identify the following critic d operational parameters of a segmented-blade conveyor cleaner system: (1) the existence of an optimal operating pressure for the conveyor and cleaning systems and (2) elimination of recessed patterns on the working side of the conveyor belt.

Jan 1, 1989

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

B 2 Program Use Instructions necessary to execute the program, after the card deck has been prepared, are summarized in the following. B 2. 1 Input Data Format Input data is supplied to the program in two ways a. By data cards that are read in after program compilation. b. By data specifications that are included within the program.

Jan 1, 1976

Provide a coalbed methane data source for industry use in mine planning. Approach Coalbed methane data have keen collected and formatted into a computer implemented data base with software developed for storage, retrieval, and generating files of selected data in response to information requests and for statistical analysis of relationships among various coal parameters. How It Works Coalbed methane data is obtained by the Bureau's direct method test on exploration coal cores. The test involves sealing fresh coal cores in desorption canisters and periodically bleeding the gas into a water-filled, graduated cylinder to measure the volume of gas released. Coalbed methane data collected over the past 9 years have been entered into a computer-implemented data base for efficient retrieval and statistical analysis. Data base processing is accomplished with a commercially available storage, sorting, retrieval, and report writing software package (Datatrieve 11). Information requests from the coal industry are processed with the system, and the data in the desired output format am printed and forwarded to the requestor. Information such as coalbed name, location (state and county), depth of sample, gas content, and coal rank are available from the system. The data can be used for

Jan 1, 1982

To quickly and more reliably measure the alignment and deflection of mine guides used to run skips and cages into a mine shaft. The Problem Conventional mine guide alignment measuring systems require the use of a plumb bob and tape measure. This method is not only laborious, but it is time consuming as well. Approach Aware of the drawbacks of the current measuring method, the Bureau of Mines designed a self-contained instrument system that can accurately perform vertical guide alignment and deflection measurements by remote control. How It Works The Bureau-developed instrumentation system, called the Guide Alignment Measuring System (GAMS), is based on conventional mechanical electronics using inclinometers and displacement transducers. The instrumentation system is attached to an operating skip or cage where it functions as a completely self-contained measurement system, operating in conjunction with nor-mal travel of the skip or cage. An on-board tape recorder or a mini-computer with memory can be used to record all telemetry.

Jan 1, 1987

Provide respiratory protection for escape in a toxic or oxygen-deficient atmosphere with a device small and light enough to be belt-worn. Approach Combine a 10-minute, belt-worn respirator with a stored, larger, long-duration (60-minute) attachment that can be plugged into the 10-minute unit without removing the mouthpiece. How It Works The 10-minute device will be carried by the miner at all times, and the 60-minute canister or attachment will be stored near the miner. In the event of a disaster, the 10-minute device would be donned immediately. The miner would then proceed to the stored 60-minute unit and plug it into the 10-minute unit. For the 10-minute unit, a breathing circuit was developed in which air is passed through the KO2 bed twice per respiration. The 60-minute canister differs from the 10-minute unit in that air is drawn only once through the chemical bed per respira-

Jan 1, 1981

To develop and design a bit that will rapidly drill smooth and precise instrumentation holes in soft rock. Approach Use a one-piece bit made by combining a drag bit and a diamond bit. Because a smooth-walled borehole with a precise diameter is needed for borehole pressure cells (BPC) and other borehole instruments, a diamond bit is usually used. However, diamond bit drilling is slow, and the bit will tend to bind when squeezing ground is encountered. On the other hand, the drag bit will cut faster, but the walls of the drill hole will be rough and the diameter will not be as precise. The combination will provide a bit which penetrates as rapidly as a drag bit, but retains the smooth-wall and precise borehole diameter of a diamond bit. How It Works A three-foot-length of EW-size drill rod is centered in a diamond bit by welding it to three equally-positioned spacers at each end of the bit. A drag bit is attached to the EW rod with a standard EW-to-drag bit adapter as shown in the diagram. Three equally-spaced diamond inserts are set to the desired hole size and welded to the diamond bit barrel behind the crown. These inserts increase the smoothness and precision of the hole by cut-ting away any hole closure. Three equally-spaced shims are set approximately 0.020-inch under the overall insert diameter size and welded to the rear of the diamond bit barrel. The combination bit should be used on a diamond drill with either water, mist or air as the coolant.

Jan 1, 1982

Develop a user-friendly computer program that permits those interested in mine health and safety to access and analyze on a personal computer (PC) employment, production, and accident data for U.S. coal and metal-nonmetal mines. This software is being designed with a major focus on flexibility and case of use. The Mine Accident Decision Support System (MADSS) will be available for distribution in mid-1994. Currently, the U.S. Bureau of Mines (USBM) is seeking volunteers willing to pilot test a preliminary version of the software and to provide suggestions for its improvement. Background Since 1975, the Mine Safety and Health Administration (MSHA) has compiled large data bases of information about U.S. mines and the reportable accidents, injuries, and illnesses that have occurred in those mines. Employment and production data arc collected on a quarterly basis from each mine and accident information is collected on an incident -by-incident basis. The USBM has compiled estimated costs for each of these accidents using computer models. All of this information is potentially useful to mine health and safety researchers. However, it has been underutilized because it is stored in large mainframe data bases that arc inaccessible to many users and/or are cumbersome and difficult to use.

Jan 1, 1993

By W. W. Adams

"Fatal accidents at coal mines throughout the United States killed 234 employees during January 1924, according to reports from State mine inspectors to the Bureau of Mines of the Department of the Interior, Included in the number of fatalities are 68 deaths caused by two explosions during the month, one explosion occurring in a mine at Johnson City, Ill., and causing 32 deaths, and the other in a mine at Shanktown, Pa., and causing 36 deaths. The fatality rate for the month was 3.94 per million tons, based on a production of 59,435,000 tons of coals In January 1923 the fatality rate was 3.52, based on 206 deaths and an output of 58,458,000 tons.Bituminous mines in all States reported 202 fatal accidents, the production being 51,170,000 tons., and the fatality rate being 3.92, as compared with 3.28 for January last year, For the anthracite mines in Pennsylvania, the reports covered 32 fatalities, which, on the month's output of 7,955,000 tons, indicated a fatality rate of 4.02 per million tons, as against 4.89 for January 1923.As compared with January 1923, the reports for January of the present year indicated lower fatality rates per million tons for all of the main causes of accidents except explosions. For falls of roof and coal, the fatality rate per million tons declined from 1.85 in January 1923 to 1,68 in January 1924; for haulage accidents the rate declined from 0.62 to 0.42; for explosives, from 0.19 to 0.12; for electricity, from 0.12 to 0.07. The rate for explosions increased from 0.21 to 1,31 per million tons. -- Reports of Investigations, Department of the Interior, Bureau of Mines."

Feb 1, 1924