Search Documents

By D. J. Dollhopf

An overburden handling dragline operation was conducted at a strip mine near Colstrip, Montana. The objective of the demonstration was to determine the degree a dragline could mix overburden inhibitory zones during the spoiling process. In order to quantify the mixing process the overburden was: 1) scatter spoiled; 2) dump spoiled; and 3) spoiled in a normal manner. This demonstration was part of an effort to investigate means of reestablishing non-polluted hydrological systems in areas where surface mining directly impacts shallow ground-water resources. When inhibitory material constituted < 5% of the total overburden volume, such material was essentially not detectable in the resultant spoil pile. When inhibitory material exceeded 15% of the overburden volume it was always found in the resultant spoil pile, generally with a smaller extent, indicating partial dilution. Inhibitory overburden zones often reappeared at the base or top of spoil piles in the potential aquifer and root zones suggesting the need for selective placement procedures. Scatter spoiling did not appear to be significantly more effective than normal spoiling, however clump spoiling seemed to produce less mixing of inimical zones. Mining activity has reduced ground-water levels within 1600 m of the active pit. The aquifer which is developing in spoils appears to have similar confinement characteristics as those that existed in the premined aquifer. To date no definite trends have been observed concerning changes in surface or ground-water chemistry associated with mining.

Jan 1, 1978

By Sidney Speil

In the study of clays and related minerals, the analytical techniques commonly employed in mineral analysis are not always applicable. The X-ray examination of a clay sample usually will show the major constituents, but often minor· clay impurities will not be detected because of line broadening and the similarity of the main lines of clay· mineral diffraction patterns, The petrographic analysis of clay minerals with clay particles as small as a few microns is usually difficult. With still smaller particles, a gross effect often is noted in which a mixture of several constituents gives the appearance of a single constituent with the mean optical-characteristics of the mixture. 3/ The electron microscope has recently been used to study clay particle shapes of various aluminosilicates. 4/ However, this method has not yet been sufficiently explored. The Chemical method in which a mineralogical analysis is calculated from the oxide chemical analysis has been discussed by Wilson 5/ and others, and many of the shortcomings have been pointed out. It should also be recognized that the variable alkali and alkaline earth content of bentonites makes it inaccurate to assign these basic elements arbitrarily to feldspar or mica in any clay that contains appreciable bentonite.

Jul 1, 1944

By R. V. Ramani

The industrial hygiene and safety aspects with internal combustion engines in mining systems is truly interdisciplinary and encompasses many fields such as mine ventilation, exhaust gas and particulate analyses, mine atmospheric environment monitoring, mathematical modeling of generation, dilution and dispersion of pollutants in ventilation systems, and engine testing and approval. This bibliography, therefore, is a compilation of references from interdisciplinary sources pertaining to diesels and related areas. Related areas are defined as those concerned with: (i) mine ventilation system design and operation; (ii) description, measurement, modeling and monitoring of mine atmosphere contaminants, and (iii) tests, standards, selection procedures, and operational practices for internal combustion engines in underground mines. References cited from source materials span the years 1900 to early 1977. Total number of references cited is 511. Subjective criteria governed the definition and selection of references. Therefore, this bibliography is not claimed to be all-inclusive nor does it purport to be an exhaustive search of all sources.

Jan 1, 1977

By Jr. Brinkley

For a theoretical description of power plants that derive their energy from the combustion of a fuel, it is necessary to solve, to an appropriate degree of precision, a hydrodynamic problem that requires for its solution a knowledge of the thermodynamic properties of the working fluid com-posed of the products of the combustion reaction. It is usually a good approximation to assume that the properties of the combustion gas are determined by the conditions of thermal equilibrium, and it is thus possible to employ the methods of Classical thermodynamics for their computation. The thermodynamic properties of fuel gases also are of considerable importance, as they form the basis for the design of appropriate means for their effective utilization. The specification of the operating conditions to produce a gas for use as an intermediate in a chemical process, such as the synthesis of liquid fuels, may be based upon a study of the variation of the composition of the synthesis gas with changes in the various process variables. Although there exists a large number of important scientific and technical applications of the data that can be obtained from the systematic determination of the thermodynamic properties of combustion gases, such application has been greatly handicapped by the extremely tedious and time-consuming computational methods required. The development of large-scale automatic computational equipment makes feasible the initiation of a systematic program for the determination of the thermodynamic properties of combustion gases and for the application of such data to specific problems of scientific and technical importance. As a part of its program of basic research in flame and combustion phenomena, the Explosives and Physical Sciences Division of the Bureau of Mines is engaged in such a program. The present communication is designed to introduce a series of reports presenting the results of this program.

Jan 1, 1951

By George Watkin Evans

The United States Geological Survey has estimated 1 that the State of Washington contains 11,412,000,000 tons of bituminous coal and 52,442,000,000 tons of subbituminous coal, in beds more than 14 inches thick. As the present rate of production is about 4,000,000 tons a year, Washington apparently contains coal enough to supply Pacific coast markets for many years. The character of the coal beds of Washington renders the production of clean coal very difficult, and a considerable proportion of the output is washed before it is marketed. In 1915 Washington ranked fifth among the States in the amount of coal washed, though only twentieth in total output. In that year 37.9 per cent of the coal produced in the State was treated in surface cleaning plants. On account of extensive folding and faulting of the coal measures, mining in Washington presents many difficulties; therefore a description of the methods employed at some of the mines may be useful in planning operations in other regions, and is presented in this bulletin. The coals of Washington differ in quality, ranging from true lignites in Cowlitz County in the southern part of the State to anthracites in the Mount Baker district of Whatcom County, in the north~ rn part. Most of the output consists of subbituminous and bituminous coals, the latter including both coking and noncoking varieties. Analyses of the coals of the State and descriptions of the beds from which the samples were taken have been printed in publications of the United States Bureau of Mines.2 Details of coal beds and analyses of the coals of King, Kittitas, and Pierce Counties have also been published by the Washington Geological Survey; 3 and most of the coal beds of the State are described in some detail in a bulletin of the United States Geological Survey.4 In 1918 mining was in progress at 72 mines in the State 4a; 46 of these mines each employed more than 10 men underground. These mines were distributed as follows: Thurston County, 1; Lewis County, 7; Kittitas County, 14; King County, 16; Pierce County, 6; Skagit County, 1; and Whatcom County, 1. During that year a total of 5,847 men were employed, 4,172 underground and 1,675 on the surface. The average number of days worked in the State was 275, and the average yearly output per man was 706 tons. Coke is made only in Pierce County by four companies, which have a total of 341 beehive ovens. In 1918 they produced 93,699 tons of coke. Up to 1919 mining machines were little used in the State. In 1917 only 6.61 per cent of the coal :produced was undercut by machines. In that year 58.95 per cent of the coal was mined by hand, and 34.44 per cent was shot off the solid. The explosives used were as follows: Black powder, 36.6 per cent; dynamite, 38.l per cent; and permissible, 25.3 per cent. The State of Washington is divided naturally into two parts by the Cascade Mountains which extend north and south somewhat west of the middle of the State. The coal areas east of the range will hereafter be referred to as eastern Washington-though nearly all of it is west of the middle of the State-and that on the west side as western Washington. The geographical distribution of the coal fields is shown in Plate I. Exploration of the State has not been exhaustive enough to preclude the possibility of discovering, besides the foregoing, other districts that contain deposits of coal in commercial quantities.

Jan 1, 1924

By R. H. Oitto

To determine whether reflectors could substitute for the trip lights referred to in the Federal Mine Safety Code, the Bureau of Mines studied trip safety devices under simulated haulageway conditions. The noticeability of reflectors compared with trip lights and fluorescent panels was evaluated from distances of up to 850 feet with light source intensities of up to 1-6 foot-candles (ft c). Reflectors tested consisted of a reflective lens in a holder secured to a frame that can be attached to a trip. Reflectors were found to be suitable for use as a trip safety device. In fact, for the conditions in many underground haulageways some reflectors would be more effective than a permissible trip light.

Jan 1, 1968

By G. E. Johnson

Batch tests of coals and coal-derived materials were made by the Bureau of Mines to determine their effectiveness in removing organic contaminants (COD or chemical oxygen demand, comprising those organic compounds that can be chemically oxidized, and ABS or alkylbenzene sulfonate, common household detergents) from the final effluent of secondary-treated waste waters. The adsorptive capacities of flyashes, coals, including at least one sample of each rank found in this country, pretreated coals, and miscellaneous materials including commercial chars and coke, were determined and compared with that of granular activated carbon. The coals, though not as effective as activated carbon, possess an economic advantage--they are relatively inexpensive, and they can still be burned as fuel without any loss of fuel value after use in waste¬water treatment. A hvcb coal was found to be one of the best, having about one-fourth the capacity of activated carbon for COD, adsorbing about 4 percent of its weight before it became saturated. Several coals contained constituents that added to the COD content of the treated water. Thus knowledge of the performance of the coal is necessary to insure selection of a proper coal as adsorbent.

Jan 1, 1966

By C. M. Harrer

This paper describes the location, features, qualities, extent, and potential of iron occurrences and some associative resources - limestone and dolomite, coal, petroleum and natural gas, power, and water - in New Mexico. Reconnaissance investigations were made of 118 iron occurrences to determine their extent, attitude, and potential; character samples were analyzed to determine their quality and impurities; and pioneer metallurgical investigations were made on character samples to present their metallurgical problems. Some factors influencing past and potential iron markets are discussed. The most abundant iron minerals are magnetite and hematite, The higher grade deposits are extensive contact-metamorphic and pyrometasomatic replacements in calcareous Paleozoic rocks associated with intrusives. Low-grade deposits of considerable potential are the extensive Cambrian oolitic hematites of sedimentary origin and the Precambrian magnetite-hematite taconite iron formation. Iron occurs also as extensive colluvial and alluvial concentrations. A wide variety of accessory elements are indicated and these pose metallurgical and economic problems.

Jan 1, 1963

By C. M. Harrer

This paper describes the location, features, qualities, extent, and potential of iron occurrences and some associative resources -limestone and dolomite, coal, petroleum and natural gas, power, and water - in New Mexico. Reconnaissance investigations were made of 118 iron occurrences to deter-mine their extent, attitude, and potential; character samples were analyzed to determine their quality and impurities; and pioneer metallurgical investigations were made on character samples to present their metallurgical problems. Some factors influencing past and potential iron markets are discussed. The most abundant iron minerals are magnetite and hematite. The higher grade deposits are extensive contact-metamorphic and pyrometasomatic replacements in calcareous Paleozoic rocks associated with intrusives. Low-grade deposits of considerable potential are the extensive Cambrian oolitic hematites of sedimentary origin and the Precambrian magnetite-hematite taconite iron formation. Iron occurs also as extensive colluvial and alluvial concentrations. A wide variety of accessory elements are indicated and these pose metallurgical and economic problems.

Jan 1, 1963

By A. E. Raddatz

The Bureau of Mines is investigating methods for recovering tungsten from domestic resources. A calcine-quench-leach (CQL) technique was developed for the extraction of tungsten from the Golconda, Nev., hot springs ores. The deposit contains disseminated tungsten that cannot be beneficiated by conventional techniques and must be treated by hydro-metallurgical methods. The CQL procedure consists of calcining the ore at 900° C for 3 hours, quenching in a solution containing 1.5 parts of Na2C03 and 1.5 parts of NaOH per part of WO3 in the ore and at a solution-to-ore ratio of 3 to 1, leaching at 200° C and at 250 psig for 3 hours, and filtering and washing the residue. A series of closed-circuit batch tests showed that 92 pct of the tungsten was extracted from a sample containing 2.32 wt-pct W03. The pregnant solution contained 11 g/l W03.

Jan 1, 1982

The principal activities of the Bureau of Mines Explosives Research Center from July 1, 1962, to June 30, 1963, are described briefly in part 1. Part 2 gives short abstracts of publications that appeared during fiscal year 1963; in general, the research reported in these publications antedates the report period.

Jan 1, 1965

By P. M. Ambrose, C. Travis Anderson, Cresap Moss, R. S. Dean

"MANGANESE METALMethods of PreparationMethods of preparing the manganese metal that has been used in chemical and metallurgical investigations have passed through a cycle. Most of the investigations made before the turn of the century used Moissan's pyrophoric manganese. 5/ This material was made by electrolysis into a mercury cathode and distillation in vacuo. It was essentially a pure material, and investigations in which it was employed (with proper precautions against oxida¬tion) led to accurate results concerning the intrinsic behavior of metallic manganese.An early investigation of the properties of ""Manganese-by-Mercury"" was made by M. Guntz. 6/ He prepared manganese by electrolysis of a concentrated MnCl2 solution with a mercury cathode. The manganese amalgam was pressed through chamois and distilled in vacuo (2 to 3 cm. of mercury) at 200°0., slowly rising to 250°0. Guntz recognized especially the decreased reactivity of manganese with increased temperature of mercury distillation. The most careful and com¬prehensive study of manganese made by this method is that of Kuh 7/ whose work unfortunately was never published in an accessible journal.Royce and Kahlenberg 8/ studied the electrode potential of manganese made by this method."

Nov 1, 1939

By M. Leva

WITH the development of new processes for the production of synthetic liquid fuels, an extensive literature search was undertaken to uncover fundamental relationships between fluid and heat flows and the operating variables of new types of converters. Examination of published correlations revealed that considerable uncertainty existed in the correlation of the operating variables of such equipment with the pressure drops which could be expected through packed and fluidized systems; correlations proposed in the literature differed from each other frequently by as much as 75 to 100 percent. Because new processes, especially more recent modifications of the original Fischer-Tropsch process, must compete with old, firmly established processes on the basis of unit product cost, the pressure-drop correlations in the literature were considered to be too inaccurate for use in calculating the energy required to pass fluids through packed beds. The following study was begun in 1946 to develop correlations that would be suitable for the design of new equipment in which fluids are brought into contact with granular materials. To arrive at general relationships, systems were chosen that did not involve chemical reactions, and a, particular effort was made to give the correlations only in terms of quantities that are ordinarily available from general process and design specifications.

Jan 1, 1951

By Northcutt Ely

This volume summarizes mining and petroleum legislation in 45 African jurisdictions. Within these jurisdictions, primary attention is given to requirements that must be met in each country for acquisition of rights to permit development of mineral resources. Coverage includes: First, identification of the controlling laws or statutes governing minerals acquisition and reference to the administrative authority; second, analysis of the laws governing mines and quarries and their products; third, analysis of laws applicable to natural gas, petroleum, and related materials; and fourth, mention of laws regulating offshore operations. Where pertinent, sections dealing with historical background or administration have been added. In countries where minerals are subject to control of states or provinces, those areas are considered separately from the central government.

Jan 1, 1974

By Earl T. Hayes

[This work represent a continuation of the efforts of the Metallurgical Division of the Bureau of Mines to ascertain and apply knowledge of miner physics to processes metallurgy.]

Jan 1, 1941

By Earl T. Hayes

[This work represents a continuation of the efforts of the Metallurgical Division of the Bureau of Mines to ascertain and apply knowledge of mineral physics to process metallurgy.]

Jan 1, 1941

This summary of State laws on explosives was compiled primarily to ascertain what subjects relating to their control have been acted upon by each State legislature and, in general, how they have been treated. It does not include any legislation passed after 1942, or any proclamations, regulations, or administrative orders. It does not purport or attempt to be authoritative. If any problem arises involving interpretation of the statutes of any particular State, the original source must be consulted for the exact words used by the legislature. This summary, however, will be useful in determining whether relevant statutes exist and in locating them quickly, with a minimum of effort. It will be of value also in comparing statutes in one State with similar statutes in other States to determine what construction has been placed upon them by the courts of those jurisdictions or to contrast the varying provisions of many States upon a single subject. To make these comparisons easier, the statutory provisions for each State have been grouped under several major topics in outline form. Although

Jan 1, 1943

By Pamplinm J. W.

"INTRODUCTION For the past six years the United States Bureau of Mines in cooperation with the University of Alabama, Tuscaloosa, Ala., the Missouri School of Mines and Metallurgy, Rolla, Mo., and certain operating companies of the Florida land-pebble phosphate district have conducted an investigation to determine the amenability of phosphatic sands to concentration. 4 This paper discusses briefly an investigation of the concentration of fine phosphatic sanads of the land-pebble district of Florida. The process used - namely, the tabling of material previously given a selective oiling treatment - is new in its application to the phosphate industry, although old in principle.The feed to the standard phospidate washery is a hydraulically wined mixture of phosphate pebbles, quartz sand, and clay in which the quartz sand grains are segregated in the fine sizes. Me standard method of concentrating (washing) consists of wet-screening. at about 20 mesh to recover the plus 20-mesh material. 5 Lately some of the washeries have introduced hydraulic classifiers for sizing of the screen undersize to recover the coarser spigot products, but even this additional treatment allows much of the fine phosphate to be wasted."

Dec 1, 1932

By Theresa Y. Schulz

It is interesting to study the noise standards that have been promulgated in the US over the last decade or so. These regulations are likely to have long-lasting impact. The Occupational Safety and Health Administration (OSHA) Hearing Conservation Amendment (March 1983) continues to have influence not only in the workplace but in the debate over new regulations. Both the Mine Safety and Health Administration (MSHA) and Federal Railroad Administration (FRA) regulatory preamble documents state the desire to be consistent with OSHA. An examination of Table 1, which compares the major components of the three regulations and the 1998 NIOSH “best practices” criteria, depicts the extent to which that intent is met. There has been some regulatory activity in the last decade which may give some hope for evolution and updating based on the wealth of science that has occurred during the last quarter of a century since the OSHA regulation was enacted. However there has also been some “back-sliding” toward more lenient standards. The MSHA noise standard made regulatory progress in September 2000 by emphasizing engineering and administrative controls, followed by personal protective equipment, in the hierarchy of noise intervention. MSHA’s requirement for technician certification (today only available from CAOHC) strengthened the training requirements for audiometric testing in hearing conservation programs and MSHA also added the requirement of dual hearing protection at 105 dB TWA. There were many subtle differences between OSHA and MSHA based on comments and a desire to clarify some of the vague aspects of the OSHA noise standard, and meet the needs of the regulated mining industry. One example pertains to the ceiling for exposures. OSHA says, “no exposures >115 dBA,” which is interpreted to mean no unprotected exposures above that level, giving credit for the assumed effectiveness of hearing conservation programs, hearing protection devices and administrative and engineering controls. MSHA specified that a “P” code1 violation be issued for any protected or unprotected exposures >115 dBA. The Federal Railroad Administration (FRA) noise standard for railroad operating employees, which went The Modern Evolution of Hearing Conservation Regulationsinto effect February 26, 2007, was expressly based on the OSHA standard but also uses MSHA for comparison. The preamble states that the FRA defers to OSHA as the “primary regulator of noise in the workplace,” but also acknowledges the need for some departure from the OSHA regulation (FRA Preamble II.B). As an example, FRA requires testing at 8000 Hz “because it will allow employers to identify hearing loss sooner.” The FRA rejected MSHA’s hierarchy of noise controls in favor of requiring specific engineering interventions and focusing on appropriate hearing protection which would still allow communication and audibility, and identification of excessive noise through employee-filed “excessive noise reports.”2 Where OSHA has no specific mandate requiring employees to take advantage of the employer-paid audiogram, it has been traditionally a condition of employment and is generally accepted that OSHA-covered workers require an annual audiogram. MSHA addressed this issue in its preamble; however, they made no significant change. MSHA employers are required to offer annual audiograms but MSHA stopped short of requiring employees to comply with annual audiometric testing. The MSHA preamble does allow that mine operators can also make audiometric monitoring a condition of employment. FRA requires employees to

By K. B. Higbie

The quantitative separation of tantalum from columbium has been obtained through several liquid-liquid extraction processes. The valuable metals are separated by selective extraction from organic feed solution using a mineral acid or by selective extraction from aqueous feed solutions employing an organic solvent. The greatest degree of separation was obtained when organic ketones, particularly methyl isobutyl ketone, were used. Approximately 200 combinations of various organic solvents and mineral acids were tested as possible separation systems in which the tantalum or columbium content was extracted from organic solutions of the anhydrous pentachlorides.

Jan 1, 1956