Search Documents

By S. Chai

Waste dumps are widely used to discharge stripped mine wastes in open pit mining methods. As mining progresses, the height of the waste dumps will increase gradually, which may induce sliding failure once the height exceeds a critical value. Therefore, estimation of the maximum dumping height is crucial to the life-cycle use of a waste dump. However, published information about the maximum height of mine waste dumps are extremely rare. In this study, the maximum dumping height is estimated based on the strength-reduction technique by numerical simulations. The influences of dump geometry and properties on the maximum height are investigated. The results show that the maximum dump height decreases as the dump slope inclination angle α or the unit weight of dump materials γ increases, but decreases when the shear parameters of dump materials (cohesion c and internal friction angle ϕ) increase. The maximum height starts to increase with the ground inclination β when shear failure occurs at the interface between the dump and the base. Furthermore the effects of the dump width B, Young’s modulus E, and Poisson’s ratio μ of dump materials on the maximum height are almost insignificant. Good agreement was found between numerical results available in the literature and those obtained in this study.

Oct 1, 2022

By I. Ngo, L. Q. Ma, J. S. Guo

Deformation of gob-side entries has always been a critical concern for ensuring stability in longwall coal mines. This paper addresses the significant deformation and support challenges that arise in thick and hard roof longwall faces (THRLF) due to dynamic pressure. The study aims to elucidate the characteristics and mechanisms of deformation during the retreat of the longwall face. The research findings indicated that the primary cause of deformation was the combination of advanced abutment stress resulting from longwall face mining and the movement of the lateral roof over the chain pillar. To mitigate this issue, we propose a deformation control method known as cutting off the lateral roof (COLR) over the chain pillar. Simulation results demonstrate a significant reduction in roof stress and deformation of the gob-side entry after implementing the lateral roof-cutting technique. These findings provide valuable guidance for effectively managing deformation in gob-side entries, particularly when dealing with thick and hard roof strata.

Aug 3, 2023

By C. Ntsele

Stirred milling technologies have firmly established themselves in concentrator circuits as energy-efficient alternatives to tumbling ball mills. High and continued increases in electricity costs, coupled with the ever-increasing power consumption by primary grinding circuits due to declining head grades of ore-bodies, provides a compelling case for these technologies. Additionally, the ability to successfully deploy stirred milling in coarse grinding applications extends the range of use in concentrators, thus increasing the opportunity matrix for energy optimization in a flowsheet. This paper therefore details methodologies and strategies that can be applied to evaluate the optimum stirred milling solution for different concentrator applications. These methods and strategies will focus specifically on the two major stirred mill machine types; namely, gravity-induced (VERTIMILL? grinding mill and Nippion-Eirich tower mill) and fluidized (SMD, Isamill?, Knelson-Deswik mill, etc. ). Finally, case studies from circuits across industry and laboratory tests will be used to illustrate the energy benefit from the use of stirred mills.

Jan 1, 2012

By C. Bester, G. M. Rohde

A major challenge in the mining sector is the responsible management and efficient storage of mine residue. Over recent years numerous tailings dams have experienced unintended spills and failures, with severe consequences for the mining industry, the environment, local communities, and the regional economy. The fourth industrial revolution (4IR) is impacting society due to increased interconnectivity, processing speed, and automated technologies. This paper explores whether 4IR technologies have the potential to mitigate risks associated with tailings dams. Experts in the field of tailings dam operational management were surveyed to determine their view on the risks associated with tailings dams and the potential of 4IR technologies to mitigate these risks. The survey found that a majority of experts believe that certain 4IR technologies have the potential to reduce the risks associated with tailings dam failures.

May 27, 2025

The Annual General Meeting of the Institute was held in Kelvin House, Johannesburg, on Wednesday, August 14th, 1974. Mr P. W. J. van Rensburg (President) was in the Chair. There were present 56 Fellows, 21 Members, 2 Graduates, 5 Associates, 16 Students, and 58 Visitors, making a total of 158. The President declared the Meeting open at 4.08 p.m. OBITUARIES The President: Ladies and gentlemen, before we start the business of the meeting, it is my sad duty to announce the deaths of the following members of the Institute since our last meeting: Dr O. A. E. Jackson, Honorary Life Fellow and Past President; C. Airth, T. L. Blunt, A. E. Frazer, C. L. Lamb, and K. Richardson, Life Fellows; and J. T. Beaumont, Fellow. As you know, there were a number of other deaths during the year, which were reported at previous General Meetings of the Institute. As a mark of respect to the memory of the deceased, and in sympathy with the bereaved, I ask you to rise and observe a few moments' silence. MINUTES The President: Ladies and gentlemen, the next item on your agenda is confirmation of the minutes of the General Meeting and Special General Meeting held on May 22nd, 1974. These will be published in the August issue of the Journal, and, since you have not yet received this, I must ask that they be held over to the next General Meeting. WELCOME The President: It is a very pleasant duty for me to welcome many members of our Institute and our guests, among whom we are particularly pleased to see the President of the Chamber of Mines, Mr Dolf Schumann, who is also Honorary President of this Institute. Mr Schumann, we are extremely pleased to have you with us today. And, we welcome an old friend of ours, Mr Dillon, Minister of Mines in Rhodesia, who has come down for our Annual General Meeting. Mr Dillon, we are very, very pleased to see you here this evening, and we look forward to seeing Mrs Dillon a little later. And we have with us, too, the presidents or representatives of many of our sister and brother associations, institutes, and societies. In particular, we welcome Mr Mike Gericke, President of the South African Council of Professional Engineers, and Professor Midgley, President of A. S. and T. S. We are also pleased to welcome the Presidents of the Mechanical Engineers, Electrical Engineers, Certificated Mechanical and Electrical Engineers, the Civil Engineers, the Joint Council of Scientific Societies, the Mine Ventilation Society, the South African Association of Consulting Engineers, the Association of Mine Managers, the Institute of Foundrymen, the Institute of Welding, the Federation of Societies of Professional Engineers, Mine Surveyors, Production Engineers (London), and the Institute of Production Engineering. We are very glad, too, to have with us a visitor from England, Professor Raynor and Mrs Raynor. Professor Raynor is Professor of Metallurgy at Birmingham University, and a very well-known metallurgist in Britain. We also have with us the Chairman of the Ferro-Alloys Association. We are expecting the Chairman of our Witbank/Middelburg Branch, the Chairman of the Engineers' Liaison Committee, Pretoria, the Director of the Witwatersrand College of Technical Education, and, of course, our old friend, Mr Eric Boden, the Manager of A.S. and T.S. It is a very great pleasure to have with us a number of persons who will receive honorary Life Fellowship at this meeting, and there are some Gold Medal winners and winners of our Student Prizes. We have apologies from a number of people who are away on business, and unfortunately some are ill. But we are extremely pleased to see those of you who are here, and we are also very pleased to see so many ladies. We expect to see many more of them later this evening, at our Cocktail Party. MEMBERSHIP The President: I have pleasure in announcing that, their names having been published in accordance with By-Law 5.2.2., the following have been elected by Council to membership in the following grades Fellows: B. Collins, D. W. Dixon, J. P. Dreyer, A. T. Hudson, and W. W. Pearce. Members: A. T. Fisher and I. F. Nagy. Associate Members : P. D. de Bruyn and H. C. Iverson. Graduates: D. P. O'Shaugnessy and M. F. Sadler. Associates: R. J. Bushell and A. MacDonald. Students : I. J. Barker, P. J. Charter, J. P. de Witt, G. S. Esterhuizen, N. Green, P. M. Jenner, M. J. R. Meyer, A. P. Nicol, W. J. C. Pothas, B. J. Robbetze, N. T. Sutherland, B. A. Statham, C. R. Thomas, N. C. Webb, M. Salamon, R. G. Jurd, and M. McChesney. Transfers to other grades of membership include the following: Member to Fellow: B. W. Holtzhousen. Graduate to Member: T. S. Schultz. Associate to Associate Member: C. L. Jordaan, H. J. L. Tomlinson, J. E. Forbes, G. H. S. Bamford, T. F. Carswell, J. W. Breidenhann, J. R. Garbutt, and L. S. Gibbs. Student to Graduate: C. J. Faueonnier and B. Lund. Student to Associate : G. P. Gooding. We welcome these new members

Jan 10, 1974

By R. Trammell, O. Eterigho-Ikelegbe, S. O. Bada

In response to the enormous amounts of coal discard generated during coal mining and preparation, the development of an efficient and sustainable strategic use of this resource is essential. Furthermore, the rising urban population over the next decades is confronted with the depletion of quality raw materials for building components. To this end, this study reports new information on the morphology, water absorption, and flexural strength properties of ceramic composites produced from three different coal discards and polysiloxane pre-ceramic polymer (PCP) resin. In addition, test results relating to the continuous operating temperature, chemical resistance, and efflorescence potential of the composites are presented. The results show that the water absorption and flexural strength of the coal composites, up to 1.94% and 36.46 MPa respectively, exceed the requirements for ceramic and clay roof tiles. The continuous operating temperature of composites is found to be more thermally stable than conventional roofing tiles (concrete and ceramic) between ambient temperature and 600°C. In addition, the excellent chemical resistance of the composites (94.43%−99.98%) compared to conventional roofing tiles (67.82%−99.97%) eliminates the need for additional external coatings. The interesting results documented so far suggest that this technique could be used to produce low-temperature application building products such as bricks, panels, roofing tiles, etc. This new recycling technique offers an excellent opportunity to eliminate enormous volumes of coal discard and to advance the circular economy in the coal industry.

Aug 2, 2022

By M. M. Makhofane

Anhydrous zirconium tetrafluoride can be used as a precursor for the manufacturing of nuclear-grade zirconium metal. This can be done by fluorinating plasma-dissociated zircon with ammonium bifluoride in a batch reactor. This paper describes the batch process. It was proved that anhydrous zirconium tetrafluoride can be manufactured by this route as confirmed by X-ray diffraction. The process shows potential for scaling up to the kilogram scale and possibly the tonnage scale.

Jan 1, 2012

By I. Druce, C. Li, T. Qu, J. Dong, W. Y. Xinchao, V. Nkuna

CITIC Heavy Industries has a large installed base of grinding equipment throughout Africa in different configurations, including high-pressure grinding rollers with ball mill and semi-autogenous ball crusher. The total installed power of CITIC’s mills exceeds 430 MW. In this paper, we compare several typical grinding circuits of copper in Africa with about 15 kt/d throughput based on ore properties, process selection, equipment sizing, and key equipment capital and operating costs. Actual operating performance is also introduced. The comparison for the following mine sites provides a general reference for the selection of copper grinding circuits with this approximate throughput: Kamoa-Kakula Copper Mine with high-pressure grinding rollers with ball mill circuit, and Deziwa and Sicomine Copper-Cobalt Mines with semi-autogenous ball crusher circuits

Jan 1, 2023

Council for 1998/99 President R.P. Mohring President Elect J.R. Dixon Vice Presidents Senior M.H. Rogers Junior Dr L.A. Cramer Immediate Past President Dr N.A. Barcza Honorary Treasure J.A. Cruise Members of Council J.P.W. Bennie E.G. de Villiers A.A.B. Douglas F.M.G. Egerton R. Graham Dr R.G. Gürtunca Dr R.V.R. Handfield-Jones P.J. Knottenbelt R.G.B. Pickering* P.S. Piper Prof. R.F. Sandenbergh Dr T.R. Stacey D.J. van Niekerk P.J. Venter J.C. Viljoen

Jan 1, 1998

By L. Naude, J. Cloete, S. Engelbrecht

The results of an investigation evaluating whether an industrial plant, currently operating using sodium isobutyl xanthate (SIBX) as primary collector for sulphide minerals (mainly chalocopyrite), could adapt to operate using an alternate primary thiol collector without compromising plant and metallurgical performance. Initial laboratory scale flotation tests identified commercial dithiophosphate (DTP)-based and thionocarbamate (TC)-based collectors, that when blended, showed potential to replace the incumbent SIBX primary PGM collector. Industrial plant trail results show that there was no deterioration in recovery of 4E PGMs, even at a lower concentrate grade when operating the plant on the identified (DTP + TC)-based collector blend compared to SIBX. The effect on Cr2O3 content in the final concentrate was also found to be negligible. The (DTP + DTC)-based collector blend also showed promise in terms of plant adaptability in accommodating a new primary specialty collector blend. These observations highlighted the potential of replacing xanthate primary collectors with alternate thiol collector blends for PGM flotation. Keywords: PGM, xanthate replacement, specialty collector, sodium iso-butyl xanthate (SIBX), dithiophosphates (DTP), dithiocarbamates (DTC)

Jan 1, 2020

By S. M. H. Haddad, M. Saghaeian, R. Hejazi, V. Sheikhzadeha, A. H. Baladastian, A. Dehghani Ahmadabadi

Sulfide impurities in iron ore concentrates play an important role in designing pelletising and steel making plants. Therefore attempts are made to keep the sulfur content of the final concentrate produced by the plants as low as possible. Generally, in the beneficiation process of iron ore concentrate, the removal of sulfur is performed through magnetic separation systems, followed by reverse flotation. The sulfide content of the iron ore concentrates originated from two main sources, including pyrite and pyrrhotite. In this research, in order to compare the floating capability of these two types of sulfide minerals, two iron ore concentrates with different sulfide constituents, pyrite or pyrrhotite, were selected. Reverse flotation tests were done separately on these samples under similar conditions. Process parameters considered for the tests included pH (2, 4, 6, 8 and 10), collector consumption (150, 200, 250, 300 and 350 g/t) and frother consumption (40, 50, 60, 70 and 80 g/t). Potassium Amyl Xanthate (PAX) and Methyl Isobutyl Carbinol (MIBC) were the collector and frother used in the tests, respectively. For modelling and optimising process parameters, the Central Composite Design (CCD) method was applied to the test results. Empirical coded equations were obtained for responses involving weight recovery, Fe recovery, Fe grade and S grade. Finally, comparison of test results revealed that the elimination recovery of pyrite sulfides was far greater than pyrrhotite sulfides, and it was possible to remove 84% sulfur content of the pyrite sample compared to minus 30% for the pyrrhotite sample. Keywords: Reverse flotation, pyrite and pyrrhotite, sulfur removal, iron ore concentrate, beneficiation plant

Jan 1, 2020

By Brian W. Mackenzie

The mineral exploration environment has observable economic characteristics, the assessment of which provides guidelines for exploration planning in the mining company. The long-term survival of the mining company is directly dependent on successful exploration. Exploration planning contributes to successful exploration through the development of exploration strategies. The objective of exploration planning is to select exploration environments which will enable the mining company to realize best possible profit and corporate risk conditions. Thus, the formulation of exploration strategies is based on profit and corporate risk criteria. Strategic considerations include the selection of commodities as exploration targets, geographic concentration of exploration effort, the realization of acceptable survival conditions, and the structuring of an exploration programme to optimize the economic benefits of the exploration investment process.

Jan 1, 2014

By S. Yaw Amponsah, E. Ben-Awuah, P. M. Takouda, P. Eme

Mining production scheduling is the process of determining the sequence of block extraction over a period of time that will yield the maximum net present value for a mining operation. The block extraction sequence needs to occur under certain resource constraints which presents an NP-hard problem that is computationally intractable and complex to solve for large scale problems using exact mathematical models such as Mixed Integer Linear Programming (MILP). In this paper, we used a metaheuristic optimisation model based on a Genetic Algorithm (GA) to solve the production scheduling problem. The problem definition and resource constraints are formulated using a mining specific GA that enforces block extraction precedence and mining capacity constraints through a normalisation method. A case study is implemented with the GA model, and the results and computational time are compared with that of a MILP model with CPLEX solver which is based on a branch-and-cut algorithm.

Sep 1, 2021

By A. Ennen, R. Wagner, B. Orberger, J. -M. Milazzo, N. Uhlmann, J. Banchet, J. Lucic, N. Wörlein, M. Firsching, J. L. Dubos, C. Bauer

The residues from mining and processing ores can often be considered as secondary raw materials. However, the material is only available in the form of fine particles (< 3 mm). In order to recycle these wastes, it is necessary to agglomerate it for transportation prior to reprocessing. The resulting agglomerates need to mechanically resist the stress of transportation and loading into the furnace. X-ray computed tomography (CT) is an established method for characterisation of internal structures in material science. This non-destructive technique can provide information on size and distribution of particles and grains. However, the information is not limited to the size, but also can yield structural features like orientation and position of cracks and fractures, which are important features indicating potential for deteriorating the agglomerates. Furthermore, deduced features such as contact conditions of inclusions or boundary surfaces can also be calculated. We studied binder-free tablets of manganese-oxyhydroxide, bentonite, kaolinite and slag powder using micro-CT. Inclusions of highly absorbing particles were identified using a watershed transformation with automatic segmentation by Otsu thresholding. Subsequently, the resulting data was analysed regarding their volume percentage, distribution in size and location within the sample. For the slag agglomerates, the volume fraction of iron could be determined. Furthermore, visible cracks were investigated with the goal to determine the long-term durability. It was shown that the data provided by micro-CT is reliable and helpful for the characterisation of industrial waste agglomerates. Keywords: X-ray, computed tomography, micro-CT, agglomerates, manganese fines, slags, kaolinite, bentonite

Jan 1, 2020

By Y. R. Murthy, S. Angadi, A. K. Bhatnagar, S. K. Tripathy, L. O. Filippov

Dolomite is an essential raw material for the refractory industry, a flux in the iron and steel industry and also for the extraction of magnesium metal. Generally, particle size reduction, screening and classification are used for the preparation of the high-grade sized material for different applications, whereas low-grade fine fractions are not utilised. These fines or low-grade overburdens are dumped at the mine site for future utilisation, which creates environmental issues along with inadequate space management. In the present investigation, a detailed study was carried out to decrease the silica content of the low-grade dolomite fines from Gomardih , India, containing 28.6% CaO and 20.1% MgO along with 8.3% silica. Different process flow sheet options were evaluated with a combination of dry classifier, wet classifier, gravity concentrators as well as flotation. Different process variables were assessed along with mineralogical characterisation to optimise the process for efficient rejection of siliceous gangue minerals. Results indicated that dolomite, calcite and quartz are the major mineral phases present in the ore along with other minor minerals. It was concluded that two-stage flotation was an effective process for the reduction of silica up to below 1% after grinding to a particle size below 212 μm. A process flow sheet with a combination of gravitation air classifier and flotation can produce a concentrate with silica content below 4.5%. Keywords: Dolomite, flux, dry classification, flotation, characterisation, beneficiation

Jan 1, 2020

[COUNCIL FOR 1992/93 President J.P. Hoffman President Elect Dr H. Scott-Russell Vice Presidents Senior J.A. Cruise Immediate Past President R.D. Beck Junior D.A.J. Ross-Watt Honorary Treasurer J.A. Cruise Members of Council Dr N.A. Barcza B.R. Broekman G.A. Brown P.M. Craven Prof. R.J. Dippenaar J.R. Dixon* A.A.B. Douglas B.R. Fleetwood Dr R.V.R. Handfield-Jones P.R. Janisch * co-opted P.J. Knottenbelt R.P. Mohring J.L. Nel* K.C. Owen P.D.K. Robinson K.A. van Gessel D.J. van Niekerk C.J.C.J. van Vuuren* P.M.T. White]

Jan 1, 1993

By F. T. Cawood, M. N. M. Cudjoe

The ability to conduct real-time material tracking in mines has been a long-standing challenge. Technological innovations such as radio frequency identification technology (RFID) have over the years contributed to the effective tracking of material flow and reporting of metal content. This paper outlines the laboratory procedures and results from testing the suitability of microdot technology as a viable technique for real-time material tracking in mining. The paper clarifies the reasons for conducting the test and presents the material safety data sheet (MSDS) from a South African and Canadian perspective. Microdots from three aerosol systems were immersed in water, heated to 100°C, and crushed into coarse and fine material. These tests were used to ascertain if the technology could withstand mining conditions. A strength, weakness, opportunity, and threat (SWOT) analysis was used to evaluate and compare microdot technology with RFID. It was shown that microdot technology has some potential to track ore parcels because data integrity was retained after exposure to post-blast mining conditions. However, more improvement is required to digitally detect microdots before the technology can be implemented at scale in the mining industry.

Apr 2, 2022

By E. van Steen, G. M. Leteba

Optimizing the catalytic performance of multimetallic nanoparticle (NP) catalysts demands a concrete understanding of their design, while preferentially deploying wet chemical synthesis procedures to precisely control surface structural properties. Here we report the influence of reductants such as hydrogen-rich tetrabutylammonium borohydride (TBAB) and carbon monoxide-rich molybdenum carbonyl (Mo(CO)6) on the shape and morphological evolution of Pt-based binary (PtNi and PtCo) and ternary (PtNiAu and PtCoAu) nanostructures derived from a homogeneous solution of aminebased surface active agents (surfactants) in a high boiling point solvent. We successfully synthesized nanostructures exhibiting well-defined and composition-controlled surfaces deploying a one-pot synthetic approach. The development of the surface properties was, however, observed to be alloyspecific. The resultant highly monodisperse alloy NP with narrow size distributions and facet-oriented surfaces are expected to display enhanced functionality as catalysts for utilization in specific chemical reactions.

Jun 1, 2021

By I. Çinar

Cappadocia is not only a region of Turkey with historical and touristic importance. During the cutting and processing of volcanic tuff, quarries in this region release large amounts of tuff into the environment that is viewed as waste. The release of this waste constitutes an economic loss and contributes to environmental pollution. However, through experimentation with deformation, weight per unit of volume, water absorption, uniaxial compression strength, modulus of elasticity, and point load strength index, volcanic tuff and marble dust composite materials can be produced for use in the building sector. In this study it was observed that, as the percentage of volcanic tuff dust in the mixture increased, the water absorption rate of the material increased, and uniaxial compression strength and point load strength decreased. The produced composite samples used in this study were kept for a predetermined number of times per day, and no deformation in the surface characteristics of the materials was observed. In a statistical parameter analysis, averages, variances, standard deviations, coefficients of variation, and skewness coefficients were calculated. Covariance changes between experimental parameters were also determined. In this study, two types of volcanic tuff dust, that is, yellow and red, were produced during the production of tuff-marble dust composite material. When the percentage of either type of volcanic tuff dust was increased, an increase in water absorption was observed. It was also observed that when the percentage of volcanic tuff dust was increased, uniaxial compressive strength and point load strength decreased. Furthermore, the physical and mechanical properties of the materials obtained by mixing different colored tuff powders and marble powders in different proportions were evaluated using statistical parameter analysis.

Mar 5, 2025

By A. K. Raji, M. O. Ojumu

Robotic subsea dredging crawlers are dynamically and remotely controlled vehicles that are used for deep sea mining and recovery operations. These exploration machines are released from a mother ship and move around on the ocean floor using tracks. Current ocean crawlers such as the MK3 ROST are hydraulically powered. In this paper we develop a scaled-down model for simulating and performing static loading analysis of an electrically powered robotic subsea dredging crawler (EPRSDC). The modeling, simulation, and analysis were carried out using modelling software from Solidworks. The structural frame was assembled using the Tetrix max robotics kit. The kit’s structural components were produced from 1050 aircraft-grade aluminum. The results were used in optimizing and for considering other materials, and the to identify specific areas to be reinforced in future crawler designs.

Oct 3, 2023