Search Documents

By K. C. Corin, M. S. Manono

The drive to reduce water usage globally has led to the mining industry reassessing its water usage - owing to past environmental degradation due to effluent discharge, tailings disposal and process water seepage into the water-table (Haggard et al., 2015). Factors such as water scarcity and environmental restrictions have created the necessity for recycling of process water in mining and other industries. Water recycling, however, causes an accumulation of ions in the process water, which may affect the strength of reagent action on the target mineral and in turn critical aspects of flotation may be impacted. Prior studies have shown that certain ions have specific effects on flotation: for example, calcium and copper have been found to enhance the adsorption of depressant onto gangue (Feng et al., 2013, Wang et al., 2016). Calcium and sulfate ions have been seen to give a higher concentrate grade than other ions present in process water (Manono et al., 2012). An increase in ion concentration will increase the mineral grade due to a decrease in entrainment (Corin et al., 2011). This study considers the impact of ion accumulation on reagent action and flotation response. Keywords: Flotation chemistry, water quality, ionic strength

Jan 1, 2020

By C. V. O?Keefe

Volumetric flow and mass flow are two of the critical process parameters needed to understand and control flotation processes, with others being levels, densities, and metal analyses. Both volumetric flow and density measurements can be adversely influenced by entrained air, which will result in artificially high flow readings and artificially low mass flow calculations. Array-based instrumentation has been used successfully to accurately measure both volumetric flow of aerated slurry and the quantity of air entrained within the slurry. The latter measurement has been used to correct density measurements, thus providing an accurate mass flow calculation. A case study involving the use of this technology to measure both flow rates and air entrainment levels at Eland Platinum processing facility (concentrator) will be covered in detail. In addition, with certain traditional flow meters such as electromagnetic meters, erroneous volumetric flow rates can be recorded in the presence of paramagnetic or ferromagnetic material. The use of this array technology to avoid spikes in measurements due to steel fragments passing through the pipe will also be discussed.

Jan 1, 2012

Alluvial diamond deposits covered with a thick overburden cannot be explored effectively and mined profitably with the available conventional techniques. A novel directional drilling technique has been developed and site trials have been conducted at the De Beers Namaqualand Mines situated at the western coast of South Africa. This paper describes the technique developed as well as the results of the site trials. The main task of the project is to develop a tool and a supporting system to achieve a remote exploration and ore extraction method for inaccessible alluvial diamond deposits. The project involves the acquisition of a system, commissioning on-site and evaluating the information obtained during assessment. The project consists of the design -of certain tools and instrumentation for the system, investigations and desktop studies as well as development of the system's logistics. The operating philosophy of the system is based on the keyhole surgery principle. In this study a pilot hole was drilled first, starting from the surface with an inclination to reach deeply seated diamondiferous gravel layers, followed by drilling into a more or less horizontal gravel layer for a certain length and finally pointing-upwards reaching ground surface at a predetermined exit point. The pilot drill bit was then replaced with a larger diameter reamer/mining tool and an HDPE tail pipe was attached behind the reamer. The drill string was retracted back to enlarge the guide hole and flush the excavated ore to the surface through the tail pipe. The material flow in between the sections of the system was' carefully measured to assess and record the gravel recovery rates. Several horizontal holes were drilled at preplanned drill paths to reach and follow the ore layer and the Ore extraction was achieved by means of a reamer/mining tool. Principles of the concept have been proven viable in this investigation.

Jan 1, 2010

Rock mass classification systems are extensively used in rock engineering design work, and mine design is no exception. Among the systems most widely used for mining-related design work are the NGI 0-system (Barton et al., 1974), the RMR system (Bieniawski, 1976), the MRMR system (Laubscher and Taylor, 1976) and, more recently, the GSI system (Hoek et al., 1998). Classifying the rock mass is widely seen as being the fieldwork required to characterize the rock mass and enable the application of empirical design methods associated with the different classification systems. This paper argues that it is fundamentally important to recognize the distinction between rock mass characterization and rock mass classification. These two processes should, in most cases, be separated from each other. Rock mass characterization should be used to determine the intrinsic properties of the rock mass independently of the application; i.e. independent from the infrastructure to be designed, the size, shape, and orientation of the excavation(s) or pillar(s), etc. Rock mass characterization should also be compatible with most classification systems and empirical design methods to be used. Rock mass characterization is the background fieldwork required to perform rock mass classification and/or engineering design work. Rock mass classification is the subsequent step to the characterization, and an integral part of the design process. Parameters that vary according to the design, such as the relative orientation of geological structures compared to the opening or the mine-induced stresses, should be calculated as part of the rock mass classification and design process, rather than during the rock mass characterization process. The failure to distinguish between rock mass characterization and rock mass classification can lead to major design errors and poor results.

Jan 1, 2012

By V. A. Leão, V. S. Coimbra, V. A. A. Oliveira, R. F. M. de Souza, G. M. de Lima

A willemite concentrate consisting mainly of willemite (55.3%) and dolomite (15.6%) was reduced in a tube furnace with charcoal as reductant. The effects of temperature and varying reductant additions on zinc extraction were studied. A zinc recovery of 86% was achieved with 20% reductant in the charge at 1100°C. During reduction, the calcium oxide generated through calcination of the dolomite promoted decomposition of the willemite, thus lowering the temperature at which reduction took place. The presence of CaO improved the zinc recovery at all temperatures studied. The best zinc recovery (93%) was obtained in the presence of 5% CaO, 20% charcoal reductant, and at a temperature of 1100°C. The results show that the willemite concentrate studied has great potential to be used as a raw material for the Waelz process.

Nov 6, 2023

By S. Kirkpatrick, J. Mukendwa

"The mining operation at Namdeb’s Southern Coastal Mine (SCM) is unique. It targets gravel layers up to 30 m below sea level, which continue to dip deeper, further west, under the Atlantic Ocean. On this storm-dominated coastline, severe water seepage into mining areas, rugged orebody footwall characteristics, and highly variable resource grades all contribute to a challenging operational environment. Namdeb has a proud history of innovation, and as the mine progresses further westwards and associated technical and economic challenges increase, this innovative culture has become essential to the future of the mine. The Theory of Constraints (ToC) has been widely used at SCM, and across the mining discipline, to focus efforts on improving overall business profitability. Through analysis of the mining processes, opportunities were identified, solutions developed, and initiatives implemented with staggering results across all three mining disciplines, i.e. stripping, load and haul, and bedrock bulking and cleaning. This paper outlines the solutions adopted and the results of the ToC analysis. IntroductionSouthern Coastal Mine (SCM) is one of three Namdeb operations located in the southwestern corner of Namibia, between the Orange River in the south, the Namib Desert to the east and the Atlantic Ocean to the west (Figure 1). These three geographical features set the backdrop for the world’s greatest marine diamond mining placer (Badenhorst, 2003). SCM is situated along the coastline extending from the mouth of the Orange River to Chameis Bay approximately 120 km to the north. The active mining area, called Mining Area 1 (MA1) is, however, limited to very narrow strip, 30 km in length, in the south of the licence area, close to the town of Oranjemund.Namdeb, a wholly owned subsidiary of Namdeb Holdings, is a 50/50 joint venture between De Beers and the Government of Namibia. Diamonds were first discovered along the Namibian coastline in April 1908, close to the town of Luderitz, but mining operations started in the SCM mining area only in February 1929 (Schneider, 2009). Initially all Namdeb mining operations exploited massive land-based deposits, producing nearly 40 million carats from MA1 between 1920 and 1977 (Schneider, 2009) when mining targeted onshore raised beaches west of the high water line. Since 1977 however, SCM and Namdeb have developed a unique mining method to economically extract the resource which extends westward under the Atlantic Ocean."

Feb 1, 2019

By N. Sinclair

"In open pit dozer bulk push operations, the material left resting against the highwall after blasting poses an issue. This is because dozers cannot physically get in behind the waste to begin the bulk pushing process. Instead, an excavator can be used to side-cast this waste for the dozers to access. An alternative technique is to have the dozers ‘side-cut’ the material, which involves the dozers running parallel to the wall, digging out the material, and eventually rotating their blades to begin bulk pushing. Industry practices suggest the latter technique is less productive and economical than using an excavator. However, such excavator sidecasting ‘economic viability’ assumes that smaller/ancillary type excavators are used (i.e. less than 23 m3 bucket capacity). So, what happens if some mine sites are restricted to using relatively larger excavators (> 23 m3 bucket) that are preferred for higher priority digging tasks? When can they avoid using their excavator? This paper explores multiple scenarios that have been designed and developed to simulate data results, which identify conditions in which the dozer side-cutting technique becomes more economically viable than excavator side-casting in terms of decreased unit cost per loose cubic metre. IntroductionOptimizing the cost of waste removal operations is important for the profitability of opencast coal mines. In the past decade, dozer bulk pushing has emerged and taken over from traditional waste removal operations such as dragline and truck-and-shovel methods at various sites around the world (Beatty, 1994). In a typical bulk push operation, once the bench has been blasted, waste is left resting against the highwall, which can either be cleared using a loading unit or by having the dozers ‘side-cut’ the highwall.Dozers perform most effectively when slot dozing side-by-side, perpendicular to the highwall. However, when dozers are required to remove material off the highwall, they must push parallel to the highwall, rather than perpendicular, hence ‘side-cutting’ the material to ensure a clean face. While dozer sidecutting is possible, it has been found that the majority of mine sites use a loading unit in this situation to avoid dozer inefficiency. Other perceived issues with dozer side-cutting include higher maintenance requirements and safety risks to dozer operators working in close proximity to the highwall."

Jan 1, 2019

By G. T. van Rooyen

In this overview of materials engineering, the author, drawing on his long experience from his student days until the present (emeritus professorship), briefly recounts the main developments in this field: dislocation theory, fracture problems, and the development of alternative materials such as ceramics and polymers. He then takes a look at the future, in which he foresees a greater demand for materials engineers, and leading roles for universities and technikons in collaboration with industry.

Jan 1, 1996

By R. S. Sanders, J. Schaan

Syncrude Canada Ltd. produces synthetic crude oil from Canada?s vast oil sand reserves by mining the oil sand, then separating and upgrading the ultra-viscous crude oil, or bitumen (~ 106mPa s @ 10ºC). At Syncrude?s Aurora Mine, about 16 000 tonnes oil sand per hour are mined and then transported 5 km by slurry pipeline to the extraction plant. The waste tailings stream is then transported about10 km by pipeline to a settling/sand storage basin. Oil sand slurries are reasonably concentrated (> 35%solids by volume), typically have a sand particle diameter between 0.18 and 0.3 mm, and are transported at reasonably high velocities (3 to 5.5 m/s). As one would expect, pipeline wear is a significant problem in this industry, in terms of both unplanned production outages and maintenance costs. In order to develop strategies to extend pipe life and to focus more on condition-based maintenance scheduling (as opposed to preventative maintenance), Syncrude has implemented an ongoing pipe wear measurement programme. Regular measurements of pipe wall thickness are obtained at various circumferential positions at a number of axial locations along each pipeline, using an ultrasonic scanning technique. In this paper, we show how wear rates vary as a function of axial location and circumferential position for oil sand hydro transport and coarse particle tailings pipelines. The specific positions at which peak wear rates occur are explained by considering the characteristics of the coarse particle slurry flows to which the pipelines are exposed.

Jan 1, 2007

Performance testing is often used by project owners and financiers to provide protection from, or assessment of, technical aspects of project design, procurement, construction and commissioning. The performance tests can range from comprehensive performance warranties relating to process performance and production in the case of lump sum turn key (LSTK) projects to less onerous demonstration tests for cost reimbursable contracts. This paper will discuss performance testing from both the contractor's and owner's perspectives and focuses on: ? when performance tests are required, ? what type of performance test/warranty is optimum for each type of project, and ? how project performance should be evaluated. The requirement for performance testing can be driven by the project financiers, particularly in the case of smaller resource development companies. In such cases, differentiation between owner's risk and contractor's risk can become contentious. At the other end of the spectrum, larger mining houses may choose to heavily influence the engineering and design process with the contractor supplying services on a reimbursable basis. In that case, the performance testing process is often limited to demonstration tests that validate performance for the owner's corporate governance requirements. This paper was prepared due to the lack of published benchmarking of performance testing and the resultant differences in expectations between a contractor and a project owner that often surface late in the contract negotiation process. The paper provides a checklist of requirements for both the owner and the contractor that may be used to provide `common purpose' early in the contract negotiation process.

Jan 1, 2007

By L. Pretorius, S. Uludağ

This paper explores how to apply system dynamics principles to surface mining problems towards understanding the consequences of mining efficiencies. Some simulation examples related to machine and people performance have been used to demonstrate systems engineering concepts to mining engineers. The simulation tool used is Vensim, which is widely used in industrial engineering applicable to systems thinking, and systems dynamics. The science and mathematics behind the system dynamics as well as benefits and typical challenges are discussed to explore the applicability to mining problems. The benefit of having one less drill is easily quantifiable with the developed model which is one of many other measurable benefits, using the developed model. Some of the benefits of the improved quality of drill holes are not fully quantified as this depends on the mine specific inputs. There are examples of quantifying this in the other industries using system dynamics tools.

Sep 1, 2021

By J. Labuschagne

The primary factor contributing to the profitability of a platinum mine and its associated concentrator is the time taken from the first hoist of material from underground to the first batch of concentrate shipped. To minimize the time it would take to produce concentrate without stopping because of a lack of feed material a project was undertaken to integrate the mining model with a concentrator production schedule () in the most capital-effective manner. A secondary goal was to ensure detailed stockpiling requirements, as the concentrator is in an area where ?visual pollution? is to be avoided. To achieve this a dynamic stockpile model was created utilizing the mine production schedule resolved into a daily production figure. Four different concentrator development models were then proposed. The difference between the mine production and concentrator consumption was integrated over the life of the mine to provide the accumulated stockpile tonnages for both Merensky and UG2 ores. The stockpile levels were never allowed to fall below zero to prevent a situation where the concentrator was operational without feed material,. When a development option was selected, the standard metallurgical performance calculations were used to derive a concentrate production schedule, that was then used as a basis for commercial concentrate sale negotiations.

Jan 1, 2012

By S. W. Jacobsz, E. P. Kearsley, N. K. Schoeman

A physical modelling approach was adopted to simulate the process of cave mining propagation at various horizontal to vertical stress state ratios, and image data was captured and used to characterize the resulting failure mechanisms. Image processing was integrated into the study to determine minor principal strains in models to identify where critical extensional strains had been exceeded relative to crack propagation. The study exhibited a scale factor magnitude of 119 using a calculated critical extensional strain value of 0.014% for the modelling material used. It was perceived that cave propagation occurred through successive parallel extensional ‘fracture bands’ in all cases, as noticed in models of prior studies, deviating from that described by the Duplancic model. Cracks tended to bisect regions of minor principal strain equal to the critical extensional strain, which suggests ‘fracture banding’ is an acceptable failure mode for brittle, rock-like materials. Moreover, it was found that models with lower horizontal to vertical stress ratios (K ratios) showed a greater degree of vertical development of the caving mechanism (at similar vertical stresses), while the vertical extent of the cave was suppressed in models with higher K ratios. Models subjected to larger vertical stresses experienced slower cave formation in latter time-steps. These models exhibited larger two-dimensional caved perimeters and areas, respectively.

Nov 30, 2022

By S. A. Lorentz, Y. Xu, C. Theron

The failure of tailings storage facilities (TSFs) results in the discharge of significant quantities of hazardous waste material into the natural environment. Research studies relating to slope instability have identified physical mechanisms such as rainfall-induced erosion, liquefaction, and shear failure as the main triggers. The generation of transient pressure waves and the mobilization of pre-event water in the unsaturated zone have been found to trigger shallow landslides in natural hillslopes. In this paper we review these physical mechanisms, known as groundwater ridging (GWR) and the Lisse effect (LE), from other studies. Previous researchers have explained both these phenomena through field and laboratory observations, numerical modelling, as well as conceptual discussions. These case studies demonstrate the impact of rainfall characteristics on the generation of transient pressure waves that rapidly increase the phreatic surface and change pore water suction. Reference is also made to the influence and behaviour of physical porous medium characteristics on the establishment of a continuous water phase that facilitates the transmission of an induced pressure head. However, previous studies fail to recognize the possibility that the pressure increase in pre-event water through pore air propagation could cause slope instability in tailings dams. The authors suggest that the physical properties and hydraulic behaviour of unsaturated porous tailings media make it susceptible to GWR and the LE, resulting in the creation of a potential failure plane.

Feb 2, 2022

By B. S. Xakalashe, M. I. Khama, Q. G. Reynolds

The carbonaceous reduction of manganese ore is an energy-intensive process that releases large amounts of pollutant gases. In an attempt to circumvent the greenhouse gas emissions, this research investigates hydrogen as an alternative reductant. The reduction of manganese ore with hydrogen results in the structural changes in the intermediate products, which might limit the diffusion of the reactant gases through the pores. Computational fluid dynamics (CFD) models capture the structural changes and predict the rate controlling mechanism and this is key in designing the prereduction reactors. The current work uses CFD models to predict the degree of reduction in a shaft furnace under hydrogen reducing conditions. Manganese ore is described as a collection of scalar and tensor fields such as thermal conductivity of the porous medium, density, and viscous resistance. The results indicate that advection contributes significantly towards the overall transport of hydrogen to the reaction sites. Porosity of the final product was found to be higher than porosity of the raw material.

Mar 4, 2025

By K. Harlow

"Zircon is a naturally occurring radioactive material (NORM) and as such is subject to a variety of regulations around the world. The regulatory processes and their implementation are summarized and the key issues affecting zircon and zirconia highlighted. Having absorbed the activities of the former Zircon Minerals Committee, the strategy of the Zircon Industry Association (ZIA) is to be the ‘go-to place’ for information on these matters, and its activities in the NORM space are described. Chemical industry regulations such as REACH are spreading around the world, and the paper provides an update of their status in the key jurisdictions. As mineral sands are transported to market in oceangoing vessels, they are subject to the regulations of the International Maritime Organization, which are summarized in the paper. IntroductionFrom a global perspective, zircon is generally not found in high concentrations other than in placer and dune deposits where it has been deposited along with other heavy minerals such as ilmenite, rutile, and monazite. Such deposits have been sorted and concentrated over geological time by the action of tides, waves, and wind to form concentrated deposits of heavy minerals along old coastlines and in river beds and deltas. Consequently, zircon is mostly found in association with the principal titanium minerals ilmenite and rutile. These secondary concentrations in placer deposits provide the commercial sources of zircon.All geological materials contain natural radioactivity, although the term NORM (naturally occurring radioactive material) is mostly used for minerals and other materials with above-average uranium and thorium concentrations. Importantly, the radioactive nature of zircon has not changed, but the way in which radioactivity is viewed by regulators has, affecting the zircon industry throughout the value chain."

Jan 1, 2017

By T. Ono, B. Altansukh, S. Kawamura, K. Haga, A. Shibayama, Y. Takasaki

In recent years, the grade of silica in zinc concentrate has increased due to the degradation of zinc content and the increase in impurity content in natural ores. It implies that the development of silica removal technology from zinc concentrate is necessary to solve problems in the smelting process caused by the high content of silica in zinc concentrate. In this paper, the authors investigated the silica removal processes from silica-rich zinc concentrate by mineral processing approaches such as re-grinding and flotation. This study focused on the pulverisation process as a pretreatment for the investigation of individual minerals' liberation from the silica-rich zinc concentrates using different kinds of pulverisers. Flotation experiments were performed to separate silica and zinc concentrate from the pulverizsd feed sample using a pH regulator (NaOH), activator (CuSO4), collecting agent (PAX), and foaming agent (DOW froth 250). Results showed that the liberation rate of silica (SiO2) was reached 75% from 13% by pulverisation in an attritor with a 2 mm ball in diameter, while silica accumulated in a fraction over 20 mm in size. Flotation experiments indicated that silica removal efficiency was achieved by 44% from + 20 mm fraction obtained from pulverisation whereas the grade of silica in froth reached 1.85 mass% from 4.5 mass%. Results indicate that silica could selectively separate from silica-rich zinc concentrate, and 99.8 % zinc recovery is achieved under the studied conditions. Keywords: Zinc concentrate, silica, pulverisation, liberation, sieving, flotation

Jan 1, 2020

By N. C. Steenkamp

Lightning has been observed in dust clouds following open-pit blasting. It is proposed that the occurrence of this phenomenon is related to the physical composition and characterization of the mineral fines that comprise the bulk of the dust cloud. Silicate minerals, which are susceptible to fine fracturing during blasting, generate the initial charge. This is further enhanced by collisions and friction during the turbulent upcast in the post-blast dust cloud. Varying size fractions result in different rates at which these particles drop out of suspension and create a secondary temperature gradient. This results in the creation of two charged zones and increases the potential of developing a discharge in the form of lightning. The ideal prevailing meteorological conditions need to be windless to minimize the effect of particle dissipation and have sufficient moisture toenhance the potential of generating lightning.

Apr 14, 2024

By N. Morris

In South Africa, diamonds are mined predominantly in rural areas. Kimberlitic diamonds dominate in Limpopo and the Northern Cape Provinces whereas alluvial diamonds are mainly sourced from the North West and Northern Cape Provinces. There are a few large and medium sized diamond companies (De Beers, Petra Diamonds, Trans Hex, Rockwell and Alexkor). There are many smaller companies involved in diamond mining, mostly alluvial diamond mines. The nature of alluvial diamond deposits is that they are aerially more extensive and thus their surface impacts are more pervasive: The recent downturn in diamond prices has resulted in the sudden cessation of mining at many small and medium diamond operations. The South African Mining Charter requires all mines, including diamond mines, to subscribe' to .the following empowerment objectives:

Jan 1, 2010

By J. H. Zietsman, S. Maharajh, J. Muller

In the chlorination process for TiO2 pigment production, blends of titania feedstocks such as ilmenite, synthetic rutile (SR), natural rutile, upgraded slag, and chloride-grade slag are reacted with coke and chlorine at a temperature of around 1000°C to form TiCl4, which is the main product, and other waste metal chlorides. TiCl4 is the main feed material for the TiO2 pigment-making process. Feeding different titania materials to the chlorinator affects the amounts of coke and chlorine required for the process, the amount of waste generated, waste disposal costs, the amount of TiCl4 produced, and bed build-up rates. These factors influence the value of the feedstock. Generally, a higher TiO2 feedstock is more valued since less waste is generated and less reagents are consumed. To quantify the impact of different feedstocks on the chlorinator, a techno-economic model was developed to describe the chlorination process and estimate process variables at steady state. This paper describes the development of the model and studies in which the model has been used to quantify the effects of using different feedstocks.

Jan 1, 2014