Search Documents

By Dhananjaya Senapati, E. V. S. Uma Maheswar, C. R. Ray

Carbothermic process of Ferro Silicon production is primarily a slag-less process. However, slag formation is observed in the regular operation as experienced by almost all the Ferro Silicon Producers in different pro-portions. The problem of slagging in the furnaces may be due to: a)Variation in the input burden charge material quality b)Fluctuations in the Carbon balance and/or c)Fluctuations in the Electrode penetrations The problem will be more severe in nature with the increase of the size of the furnace. The operation performance of the furnace gets badly affected if the slag formed in the furnace is not removed from the bath in time and to the maximum extent possible. It is, therefore, very essential to know the characteristics of the slag formed in the Ferro Silicon Furnaces, besides eliminating the very cause of formation itself; and to find the routes of draining of the same from the furnace bath effectively. This paper envisages the effects of using the LIME STONE in the Ferro Silicon Burden in stabilizing the 48MVA Furnace for improved performance and better consistency. Quality fluctuations in the available Raw Materials are compared with that of the requirements for the Ferro Silicon production. The furnace operational data is compared for 12 months period each for the period corresponding to the before and after usage of lime stone in the burden and found encouraging results in the performance. Implications of use of Lime Stone in the burden on the quality of the output alloy are also studied.

Jan 1, 2007

An effective electrowinning process in hydrometallurgical industry requires fluoride levels in the base metal solution to be less than 10 mg/l. Selective removal of the fluoride ions from base solution is thus desired, if fluoride was added to control calcium and magnesium in the circuit. Consequently, adsorption of fluoride onto activated alumina was studied in a batch and a column set-up. The effects of base metal solution pH, temperature, initial concentration and flow rate on activated alumina performance were investigated in either a batch or column configuration. A two-level factorial experimental design was implemented in studying column dynamics. Results demonstrate that activated alumina is an effective adsorbent for selective removal of fluoride from base solution. In the batch operation, fluoride was removed to values below the maximum allowable concentration (10 mg/[l]) when pH was = 8. In the column adsorption step at 55°C and 600mg/[l] initial concentration, up to 16 bed volumes were processed before breakthrough level was reached. Desorption step using 1% sodium hydroxide solution achieved an elution of 8 bed volumes. The activated alumina (AA) had a capacity of 8.65 gF/[l]AA at the 10mgF/[l] fluoride breakthrough level during the column adsorption test. Keywords: Fluoride; activated alumina; adsorption; recovery; regeneration.

Jan 1, 2009

By J. Botin

Traditional risk quantification methods provide little information on the sources of risk, and tend to produce static over-conservative evaluations, which do not account for changes in the performance of the project. Capital investment decisions for large mining projects require more complex risk evaluation models that include the value of flexibility and the different risk levels associated with uncertainty on project variables (price, grade, dilution, and production rates, among many other). In this context, real option valuation (ROV) methods have proven potential to quantify the risk associated with such variables and integrate alternative scenarios and management strategies into the evaluation process. In this paper, a risk quantification model is developed that successfully quantifies the risk associated with dilution, as a function of production rate. This model is then validated in a case study on the Chuquicamata Underground Mine project. Keywords real options, risk management, risk quantification, dilution, minine planning.

Jul 1, 2013

By S. E. Olsen, M. Tangstad

The main source of Mn in raw materials for SiMn production is Mn-ore and Mn-rich slag from the high carbon FeMn production. The amount of slag per tonne of SiMn metal is mainly determined by the ore/slag ratio. Increasing share of FeMn slag at expense of Mn-ore will lead to larger slag/metal ratio in the SiMn process. High volume of slag leads to an increased consumption of energy and probably to higher losses of metal inclusions in the final slag. Excavation of a SiMn furnace has shown that only modest pre-reduction of Mn-ore with CO gas seems to be obtained. Nearly all reduction of MnO was finished at the top of the cokebed. Dissolution and reduction of quartz obviously takes place in the cokebed zone after the main reduction of manganese oxide is finished. Probably the ?pick up? of Si in the metal is quite fast and takes place as the metal trickles down through the cokebed towards the metal bath. The distribution of Si between SiMn alloys and multicomponent MnO-SiO2-CaO-Al2O3-MgO slags is mainly determined by the process temperature, the silica content of the slag and its R-ratio = (CaO+MgO)/Al2O3. As an example, the equilibrium content of Si in the alloy will increase by about 6 % if the R-ratio is reduced from 2 to 1, provided constant temperature and silica content. The effect of temperature is also considerable. The equilibrium content of silicon will increase by approximately 6 % per 50°C in the temperature range 1550°C to 1700°C. The equilibrium content of MnO in SiMn slags depends first of all on the temperature and secondly on the silica content of the slag. At 1600°C the MnO content decreases from about 9 % at silica saturation to a minimum of about 3-4% when the silica content is reduced to about 40-45%.

Jan 1, 2004

By R. Ribacchi, P. Tommasi, C. Consorti, P. Campedel

The runout of dry blocky rock avalanches produced by planar rockslides affecting a limestone formation with clayey interbeds is analysed by means of distinct element modelling. Numerical analyses are validated by means of the back analysis of a historical rockslide occurred in the investigated area and physical aspects of the phenomenon evidenced by modelling are discussed. On analyse par la méthode aux élements distincts la distance de parcours des avalanches rocheuses sèches produites par des glissements plan interessant une formation de calcaire à intercalaires argilleux. Les analyses numeriques sont validées à l’aide de la back-analysis d’un glissement historique survenue dans le site en examen. On décrit les aspects physiques su phénomène mis en évidence par la modélisation efféctuée. In diesem Beitrag wird die Reichweite von Steinlawinen besthend aus trockenem blockhaftem Fels mittels der Distinct Element Methode untersucht. Die Steinlawinen werden erzeugt von Rutschungen in einer Kalkstein-Formation mit tonhaltige Schichten betreffen. Die numerischen Berechnungen wurden anhand einer Simulation einer historischen Bergsturzen verifiziert, der sich auf den untersuchten Gebiet ereignete. Auf der Basis der erhaltenen Ergebnisse wurden die physikalischen Aspekte der untersuchten Steinlawinen analysiert.

Jan 1, 2003

By T. F. J. Hälbich

Namakwa Sands aims to conserve environmental resources and prevent or minimize environmental impacts from its operations. The challenge faced by Namakwa Sands is the rehabilitation of the arid winter rainfall Strandveld and lowland Succulent Karoo vegetation zones affected by its mining activities. Extensive experimentation with different rehabilitation methods resulted in the development of an effective rehabilitation programme. The use of topsoil as a seed bank and shade-cloth as windbreaks have significantly aided the rehabilitation process. The aim of the programme is to stabilize the soil environment so as to allow the germination and development of the local plant species. The ability to control wind erosion is critical to the success of the rehabilitation effort. A programme of biodiversity audits has been started to measure the recovery of plant species in the rehabilitated area. The principle of continuous improvement, coupled to site-specific rehabilitation studies, is applied to enhance the rehabilitation programme.

Jan 1, 2003

By E. Pardo-Igúzquiza, R. A. Olea

The bootstrap is a computer-intensive resampling method for estimating the uncertainty of complex statistical models. We expand on an application of the bootstrap for inferring semivariogram parameters and their uncertainty. The model fitted to the median of the bootstrap distribution of the experimental semivariogram is proposed as an estimator of the semivariogram. The proposed application is not restricted to normal data and the estimator is resistant to outliers. Improvements are more significant for data-sets with less than 100 observations, which are those for which semivariogram model inference is the most difficult. The application is illustrated by using it to characterize a synthetic random field for which the true semivariogram type and parameters are known.

Jan 1, 2015

By R. G. B. Pickering

The purpose of this report is to chronicle the interaction between Anglo Platinum and Sandvik Tamrock during the development and application of Long Hole drilling as a viable, practical method of narrow reef mining. Appendix I identifies the people from Anglo Platinum and Sandvik Tamrock who participated in the project. Experiments in long hole drilling and blasting were conducted in a number of mines during the late 1950s and early 1960s. Some of the advantages envisaged were: ? The face would require no daily examination ? No barring down or immediate face support required ? No sockets to clean ? Only a few well drilled holes rather than large numbers of short blast holes ? Avoidance of poorly-marked holes, inaccurate drilling and improper charging ? Better supervision and better face advance. Holes 50 mm in diameter were drilled parallel to the stope face by pneumatic rock drills from advance strike gullies. Holes were charged with amon gelignite cartridges. All holes were traced with detonating cord to ensure propagation of the explosive along the entire hole length. Rock was blasted onto a rolling scatter pile. A number of reasons have been cited for the failure of this mining method. The two most important were: ? problems in controlling hole deviation which was exacerbated by the fractured ground ? difficulty of charging up holes in fractured ground, due to relative movement of rocks along fracture surfaces over the hole length. The idea of drilling a few long holes parallel to the face rather than a large number of short blast holes perpendicular to the face was an attractive option to mechanize narrow reef mining. This particular project started in 1998. Initial trial The Union Section of Anglo Platinum purchased a Solo H 606 RA long hole drilling rig from Sandvik Tamrock in 1997. In order to evaluate long hole drilling as a basis for face mechanization. The Solo series of drill rig was selected because it combines high drilling performance and good drilling accuracy with high versatility with a compact size. The mining method proposed by a consultant to Anglo Platinum was based on the current trackless mining method practised by Union Section. The trackless mining method is better described as a trackless development and transport method. Reef strike drives were installed approximately 40 metres apart on dip using trackless equipment. Reef was mined using hand-held pneumatic rock drills and scraper winches and the excavation was supported by sticks and crush pillars at the top of the panel. Rock scraped from the panel was loaded by Lad Haul Dumps (LHDs), trammed to an inclined haulage, and loaded into trucks for transport to the surface. It was intended that the Solo would drill from the bottom advance strike drive to the top advance strike drive. Blasted rock would still have to be scraped from the panel. It is also difficult to understand how well the support would have survived. In the initial motivation it was stated that drilling accuracy was of the utmost importance. Previous work by Sandvik Tamrock had shown that, in other parts of the world, 20 metre long holes could be drilled with a deviation not exceeding 100 mm provided that: ? holes were collared with low thrust pressure ? operating percussion pressure was kept low -often not ? exceeding 10 MPa ? drilling was to be with tubes, not rods. In early 1998 initial trials with the Solo H 606 RA were inconclusive; attempts were made to drill 40 metre long holes from one advance strike drive to another. Difficulty was experienced in measuring hole straightness and accuracy, there was no survey of the holes, and no blasting was done to expose hole barrels. A long hole mining system was then defined, with a corresponding face mining system, which led to the design of a test programme for the Solo drilling rig. Earlier experience at Telfer The proposed face mining system was based on a mining method that is practised at Telfer Gold Mine in Western Australia. Telfer has a series of domed reefs that dip at angles of less than 20° to more than 40°. The ore bodies are all thin, with widths from 0.6 metres to 0.8 metres. Figure 1 shows the face layout. Experience at Telfer indicated the following: ? The spacing and size of the dip pillars should be based on the rock mechanics of Union Section ? The length of the face is determined by the ability to correctly position the blast holes. Positioning of blast holes is a function of hole straightness and hole direction. Blast holes in Telfer were drilled 64 mm diameter with retrac bits from Sandvik. Extension steel was T38 by 1.8 metre lengths. A guide rod was fitted immediately behind the bit. To achieve greater accuracy' operators drill at relatively low percussion and thrust pressures. Results show that very good accuracy is achieved in 20 metre stopes and only fair accuracy in longer stopes. In 34 metre long stopes 10-15% of the holes are not sufficiently accurately positioned and have to be re-drilled. All blast holes are

Jan 1, 2006

By K. L. Morton

Groundwater and associated pore pressure represent elements that can have a negative impact on surface mining and slope stability. Groundwater flow and deformation within a slope influence each other. An increase in pore pressure will result in a decrease of effective stress; and conversely, if the pore pressure decreases, the effective stress increases. Slope analysis and slope design calculations require good information on pore pressure distribution around an open pit excavation. Until recently very little pore pressure data were available and assumptions had to be used. Location and design of measuring points depend on geological and structural setting, geotechnical domains and practicality. Good planning and the use of sensitive point piezometers to measure in situ pore pressures means that real-time data can be collected and used for the construction of flow nets, the determination of pore pressure distribution around an open pit mine, the validation of the dewatering/depressurization requirements, the calculation of the efficiency of the dewatering system and finally the use of pore pressure data in slope stability analysis. The recommended layout for a monitoring system, types and design of piezometers, data collection and use of the pore pressure data are presented.

Jan 1, 2008

By D. W. Nel

Nanofiltration (NF) has attracted much attention over the past few years due to the reduced energy consumption compared to reverse osmosis (RO) and better separation performance compared to ultrafiltration (UF). Although research has been done in the area of NF of nickel ions, sodium ions, and acid separation, not much attention has been given to the separation of high nickel concen¬trations from sulphuric acid streams. The use of NF for the separation of nickel and acid from a spent nickel electrolyte is an innovative process alternative for future industrial application within a base metal refinery. In this study, the separation performance of a composite polyamide NF membrane on a spent nickel electrolyte was investigated by varying the sodium sulphate concentration in the feed (50-150 g/l), the trans-membrane pressure (35-55 bar), and cross-flow velocity (1.5-3.5 m/s), and measuring quantities such as total permeate flux, acid rejection, nickel rejection, and sodium rejection. The nickel and acid concentration in the feed were kept constant with variations between 40-60 g/l and 25-40 g/l respectively, while the temperature of the experiments was kept constant at 50°C. The membrane was found to be very selective for nickel ions, with the rejection of nickel ions varying between 54.4% and 98.2%. The rejection of acid ions varied between -5.9% and 21.8%. The rejection of sodium ions varied between 16.6% and 72.4% at a cross-flow velocity of 2.5 m/s and sodium sulphate concentration of 50 g/l in the feed solution. An increase in trans-membrane pressure increased the rejection of nickel, sodium, and acid ions, while an increase in sodium sulphate concentration decreased the rejection of nickel and acid ions. The total permeate flux was found to increase with an increase in trans-membrane pressure and decrease with an increase in sodium sulphate concentration. The cross-flow velocity had an insignificant effect on the total permeate flux and the rejection of nickel, sodium and acid ions.

Jan 1, 2013

Sishen Iron Ore Mine previously used only A-grade material (>60% Fe in situ value) from the pit for beneficiating in the DMS plant to a final product grade of 66% Fe in lump and 65% Fe fine ore. The B-grade (between 50% and 60% Fe) and C-grade material (between 35% and 50% Fe) were stockpiled separately, owing to the inability of the existing DMS plant to beneficiate material at densities higher than 3600 kg/m3. The ability to beneficiate the B-grade material at densities higher than 3600 kg/m3 was evaluated, and air-pulsed jigs were found to be techno-economically feasible and value maximizing. The beneficiation of B-grade material would add to the existing DMS production of 28 Mt/a, with no additional mining cost and only limited costs for the handling of waste and B-material. The objective of the Sishen Expansion Project (SEP), i.e. the jig plant, was to produce 10 Mt/a of saleable product with six modules to the set physical and chemical specifications by 2009. During the start of construction, it was decided to add another two jig modules to the plant to increase production to 13 Mt/a. During commissioning and ramp-up the shortcomings and advantages of the jigs were fully experienced and understood, resulting in many changes to optimize jigging performance..

Jan 1, 2014

By Rajendra Singh

Underground depillaring of contiguous coal seams/sections is a difficult problem, which becomes even more complex if the interburden/parting between them is thin. Conventionally, the depillaring with caving of contiguous seams/sections is done in descending order. However, if the parting is thin, the influence of the top sections/seams working over the standing pillars of bottom the sections/seams becomes extremely important for the safety and optimal exploitation of coal. Field investigations were carried out at Nowrozabad East mine where superimposed pillars of the Johilla top section were depillared above the developed pillars of the Johilla bottom section with a 3 m thick parting between the two sections. The competency of the 3 m thick parting (which consists of alternate layers of shale, sandstone and shaly sandstone) was improved by reinforcement (underpinning). The strata control investigations did not show any considerable instability problem of the 3 m thick reinforced parting and pillars of the bottom section due to top section depillaring. On the basis of this field investigation and a laboratory study on simulated models, simultaneous extraction of both the sections, along with reinforcement of the parting, was suggested for the geomining conditions of the Johilla top and bottom sections. Adopting the suggested simultaneous depillaring process, two sub panels of Johilla top and bottom sections have successfully been extracted without any strata control problem. This paper presents this case study along with the results of the strata monitoring conducted to evaluate performance of the underground structures during the field trial.

Jan 1, 2004

By S. Thorley

In engineering design of operator?s compartments, in underground mining equipment, ergonomics principles are often neglected or not given the full recognition they deserve. This paper defines ergonomics, applies it to machinery in an underground mining environment and describes the ergonomics analysis undertaken during the design phase of an EJC extra-low-profile mining loader. Encompassing the design of the operator?s compartment of this new loader, this paper illustrates the importance of ergonomics principles within the collective design process, ensuring that it is fully integrated into the design approach. An ultimate aim of this study is to ensure that all future designs follow this route to guarantee not only the outcome of a highly efficient, cost-effective and productive machine but that it is also takes the human factor into account, not only in maintenance but also in operation. Maximizing comfort will have the ultimate outcome of actually increasing productivity.

Jan 1, 2006

By George J. Karcas, Raimo Kuusisto, Pertti Pekkala

Ongoing Outokumpu development in Solvent Extraction and Electrowinning Technology, involving all aspects of process chemistry, equipment and control, extends over a period of close to 30 years. The development in SX started with molybdenum and rhenium, continued with zinc, manganese, cobalt and nickel and is now focusing on copper. The OutoCompact VSF? SX concept, which has been recently introduced, is a honed version of earlier VSF? technology. The Outokumpu VSF? ("Vertical Smooth Flow") SX package includes the DOP ("Dispersion Overflow Pump") units, the Spirok Mixers, the OutoCompact Settlers including their DDG ("Dispersion Depletor Gate") fences and tank farm equipment such as the LOS ("Loaded Organic Scrubbing") tank as well as the CEP ("Copper Electrolyte Purifying") tank. Although the VSF? SX package can be implemented according to several optional lay-outs, the so-called Track version has lately been introduced to the advantage of new plants. The new OutoCompact SX technology decreases the footprint of future VSF? plants. The lay-out, including plant size flexibility, have further been improved by Outokumpu?s new OutoReverse settler technology. Two of several SX plants currently under construction rely on reverse settlers in order to maximize their performance. The Outokumpu EW technology includes process know-how as well as proprietary equipment. The copper EW package consists of permanent stainless steel cathodes based on wax-less technology and lead anodes utilising polymer concrete cells with the double contact bus bar system and ventilation hoods fitted for efficient mist control. The lifting of cell hoods, as well as cathode washing, is done by the cathode pulling crane. Proper electrolyte flows and matching current density further ensure high productivity of LME grade copper cathodes.

Jan 1, 2005

An efficient and portable mathematical model has been developed for simulating heat transfer in six-in-line slag-resistance-heating electric furnaces for smelting sulphide ores to produce base metals and platinum group metals. This model is a steady-state one relating furnace conditions and performances to various control and input parameters. Some transient effects occurring in electric furnaces are neglected for computation efficiency. This article describes the model development and modelling results. The present model is capable of predicting: (i) temperatures at various locations in a six-in-line furnace, such as slag bath, matte bath, solid charge, freeboard space, freeze lining, cooling water, and air gaps between solid material components, etc. (ii) freeze lining thickness, (iii)smelting rate, and (iv) heat loss rate, etc. A typical feature of the model is that it is easily portable to different application platforms and sufficiently efficient with execution times less than a few seconds. Therefore, it is possible to apply the model for online prediction and control of heat transfer and freeze lining thickness in industrial electric furnaces.

Jan 1, 2011

By G. B. Quaye

The deep level gold mining environment is characterized by high stresses that give rise to intense mining induced fracturing of the rock mass surrounding the stopes. In a geologically disturbed region where the intensity of mining induced stress fracturing is high, the degree of faulting and/or the frequency of other geological features such as joints may pose serious strata control problems. Unfavourable intersection of these discontinuities namely, faults, joints and mining induced stress fractures tend to divide the immediate hangingwall into unstable keyblocks which, if not supported, may result in extensive falls of ground. Effective support strategies therefore demand detailed investigation of the predominant inclinations and orientations of these discontinuities. The orientations and inclinations of these discontinuities surrounding a deep level stope have been measured. The results are projected onto the lower hemisphere of a stereographic net to determine the factors that contribute to the falls of ground in the stope. The analyses reveal that unfavourable intersection of these discontinuities divides the immediate hangingwall into unstable wedges that may become dislodged between support units.

Jan 1, 1998

By J. W. Klokow, K. L. Riemer, R. I. L. Ferreira

As a result of the increased depth of mining in the South African gold mining industry mining induced seismicity is a severe problem. One of the strategies within the industry to contain the problem is to incorporate a system of regularly spaced stabilising pillars into mine layouts. At the Driefontein Gold Mine a system of closely spaced dip pillars is used to contain seismic energy emissions. Comparisons of seismic data for several mining clusters initially indicated a possible measure of success in the containment and occurrence of larger events. A detailed analysis of data over a 5-year period since the start of mining however, has revealed a delayed seismic response to the increasing strike spans. Significant changes marked by an increase in certain seismic variables have been observed at mining spans of between 100 to 120 meters and could be of significance to pillar spacing in the design of deep level mining layouts. La sismicité occasionnée par l’exploitation minière est un problème grave dans les mines profondes de l’industrie minière aurifère en Afrique du Sud. Une des stratégies utilisées dans l’industrie a été de maîtriser le problème en incorporant un système de piliers de stabilisation régulièrement espacés dans la disposition des mines. A la Driefontein Gold Mine, un système de piliers de pendage proches les uns des autres est utilisé pour contenir les émissions d’énergie sismique. Au début, des comparaisons de donnés sismiques pour plusieurs groupes d’extraction ont indiqué un succès possible dans la limitation et l’occurrence d’évènements sismiques. Cependant, une analyse détaillée des données sur une période de 5 années a révélé un délai entre la progression de l’extraction et une réponse sismique accrue. Des changements considérables dans les variables sismiques ont été observés dans des intervalles d’extraction entre 100 et 120 mètres, ce qui pourrait être significatif pour l’espacement des piliers dans la conception de la disposition des mines de fond. Resultierend aus den zunehmenden Tiefen des Bergbaus in der südafrikanischer Goldbergbauindustrie stellt sich die vom Bergbau hervorgerufene Seismizität als bedrohliches Problem dar. Es war eine der Strategien innerhalb der Industrie, das Problem dadurch einzudämmen, daß regelmäßig plazierte Stabilisierungspfeiler in den Bergbaulayouts inkorporiert wurden. In der Driefontein Gold Mine wird ein System von knapp aneinandergesetzten im Abfallbereich befindliche Pfeiler benutzt, um seismische Energieemissionen einzudämmen. Vergleiche der seismischen Daten für mehrere Bergbaugruppen zeigten anfangs ein mögliches Maß von Erfolg in der Eindämmung und im Auftreten von größeren Fällen an. Eine ausführliche Analyse von Daten über einen 5jährigen Zeitraum hat jedoch ergeben, daß eine Verzögerung zwischen der Progression des Bergbaus und einer erhöhten seismischen Reaktion besteht. Bedeutende Änderungen in den seismischen Variablen wurden an Bergbauspannen von 100 bis 120 Metern beobachtet und könnten für Abstandsbemessung von Pfeilern im Design des Tiefbergbaulayouts von Bedeutung sein.

Jan 1, 2003

By J. P. Josien, Didier C.

ABSTRACT: France now faces the closure of most of its mining sites. Surface instability risk may sometimes remain, especially where large underground voids exist. This paper illustrates the importance of failure mechanisms identification in order to define properly how to manage the residual risk. RESUME: La France fait aujourd’hui face à la fermeture de ses exploitations minières. Des risques d’instabilités de surface peuvent persister, notamment lorsque des vides résiduels existent au sein des travaux souterrains. L’article illustre l’importance que présente la nature des mécanismes de rupture potentiels dans le choix des mesures compensatoires à adopter pour gérer le risque résiduel à long terme. ZUSAMMENFASSUNG: In Frankreich stellt sich derzeit das Problem der definitiven Schliessung des meisten Bergwerke. In manchen fällen ist die Stabilität der Oberfläche nicht garantiert, speziell wenn unter Tage nicht verfüllte Hohlräume verblieben sind. Dieser Bericht zeigt die Wichtigkeit, bei der Auswahl geeigneter Langzeit-Risikomanagementmethoden, der verschiedenen Mechanismen mit denen ein eventueller Bruch an die Tagesoberfläche geraten kann.

Jan 1, 2003

By L. Morgan, M. Le Roux, Q. P. Campbell

Dry coal processing is becoming increasingly favoured as a fine coal beneficiation technique. The decline in suitable good-quality coal, as well as the ongoing decrease in usable process water, makes dry beneficiation of the fine coal fraction even more crucial. Dry fine coal beneficiation is a relatively young process with most of the methods still in the developmental phase. Additionally, many of the dry processing options available are better suited for coarser (+6 mm) and easy-to-beneficiate coal. Air winnowing for fine particles has been established in both agricultural and pharmaceutical industries, which indicates that the method can be used to separate smaller particles on a density basis and therefore, may prove effective in the coal industry as well. A proof of concept study was conducted using both computer-based simulations (which do not form part of this paper) and physical experiments. The initial winnowing unit consisted of a closed box with a horizontal air stream flowing through the top section. Coal particles were injected into the air stream and displaced horizontally across a distance (x), depending on the particle size and density, thus actuating a separation based on these two parameters. For this study particle sizes of 6, 4 and 2 mm were used all with a density ranging from 1200 kg·m-3 to 2000 kg·m-3. The simulation in Star CCM+ confirmed the findings of the mathematic behavioural model and provided a virtual representation of the separation using streamlines and particle tracks. The coal tests prove that size separation can be achieved at an airflow velocity of 21 m·s-1 and the density cut-point can also be predicted by using the prediction matrices constructed as part of this study. The results show efficiency values (EPM) of 0.11 and 0.09 at density cut-points of 1400 kg·m-3 and 1500 kg·m-3 respectively. The data obtained from the study indicates that air winnowing can be used to separate fine coal particles based on both size and density. However, in order to achieve an efficient density separation, a narrow size range is required. With some improvements to the model, simulation, method and design, the separation efficiency can also be improved. The next phase of testing will include the upscaling of the process to a demonstration plant, optimising the separation unit and testing the method on different qualities of coal. Keywords: Dry processing, fine coal, winnowing, simulation, tracers, demonstration plant

Jan 1, 2020

By T. C. Alex, K. M. Godiwalla, R. K. Jana

Manganese nodule, available in ocean beds, is a potential resource of the future for copper, nickel and cobalt. Recovering only these metals, containing less than 3% by weight, will result in the generation of large amount of residue. In addition to the material losses, several environmental and ecological problems arise out of this. The present study has been aimed at reducing the environmental and ecological problems associated with massive generation of this residue together with utilization of the resources. Presence of ~ 20% manganese and ~16% silicon in the residue has prompted us to check its suitability as a raw material for silicomanganese production. Lower manganese content and lower Mn/Fe ratio of the residue than that required for silicomanganese production has been corrected in this study by suitable blending. The efficacy of blending and its thermodynamic aspects using FACTSAGE software are discussed. The studies conducted indicate viability of bulk utilisation of the residue through silicomanganese production and thereby reducing the burden on environment to a great extent.

Jan 1, 2007