Search Documents

By O. Dahl, B. Musuku, N. Schreithofer

Recovery of fine pentlandite is proving to be a challenging task in the Kevitsa sequential flotation operations, with over 60% of the nickel losses reporting into the -25μm size fraction. Since commissioning, the Kevitsa process has undergone major changes to address throughput and flotation performance. Major changes were implemented in the configuration of the milling and flotation circuits as well as in the operating conditions and reagent regime. Some of these changes improved nickel flotation while others deteriorated flotation performance. Most of the changes have had a direct impact on nickel flotation. This paper reviews the systematic analysis, laboratory testing and salient changes done to the process with special focus on the impact on the fine pentlandite flotation. Keywords: Blending, Flotation, Chalcopyrite, Pentlandite, Fines

Jan 1, 2020

By M. R. MacIver, M. Pawlik, S. Finora, H. Alizadeh

The dispersion of mature fine oil sands tailings (MFT) by the addition of sodium lignosulfonate was studied using contact angle measurements, optical scattering, and particle size measurements. Lignosulfonate caused the release of residual bitumen to the slurry surface and settlement of fines. Dynamic contact angle by captive bubble measurements were carried out on bitumen to determine the effect of the dispersant on the wettability of bitumen. Lignosulfonate caused a change in the aggregation state of the MFT and increased sedimentation of particles, as indicated by optical scattering measurements. Zeta potential measurements indicate that this change was caused by an increase in adsorption of lignosulfonate onto particles, which caused improved settling of the colloid. Ultraviolet Visible (UV) spectrophotometry and organic carbon content measurements showed that only a small amount of the reagent remains in the aqueous phase of the tailings, which is critical for decontamination of recycled water. Keywords: Oil sands tailings, bitumen recovery, dewatering, dispersion, surface chemistry

Jan 1, 2020

By Dennis Van Heerden

Southern Africa has a long history of underground hard rock mining dating back to the late 1800?s. The rock support of underground excavations has significantly changed during this period, due to improved technology, experience gained and rock support requirements by mining and geotechnical engineers. This paper examines the available underground rock support methods in Southern Africa with emphasis on the types and characteristics of: - Rock bolt types. - Rock bolt and long anchor grouts. - Thin-sprayed liners. - Sprayed Concrete. - Ground consolidations through injection methods. - Cavity and void filling with aerated cement products. [ ]

Jan 1, 2007

By N. Hadebe, A. Mampuru, F. Jantjies

Mintek conducted test work to study the effect of media wear when using Mintek’s Milling-in-raffinate technology. The grinding media consisted of high-chrome and ceramic balls. The tests were conducted using a laboratory 5L 316 stainless-steel rubber-lined mill. Magotteaux supplied the high-chrome and ceramic balls. The raffinate was synthetically prepared using a typical Cu/Co (2.2 g/L Cu, 3 g/L Co) composition. The milling rate, media wear, mill, leach extraction efficiencies, gangue acid consumption, and residence time were studied. The tests indicated that the high-chrome balls had a higher corrosion rate than the ceramic balls. The ceramic corrosion rate was lower than 0.1 mm/y. The highchrome balls performed better during the leach stages with faster milling time, higher leaching efficiencies for both Cu and Co, lower gangue-acid consumption, and lower residence time

Jan 1, 2023

By T. Käyhköa, J. Liipoa, S. Khizanishvilic, M. Sinche-Gonzalezb

The use of geometallurgical modelling is becoming more common in concentrator plant design and during the operational phase. Predictive modelling aims to define optimised process parameters for the concentrator plant to accommodate variability within the ore feed. The main objective of this study is to show how the metallurgical response of different types of ore blends can be simulated using kinetic models derived from experimental flotation tests with different geometallurgical end-member ore types and their blends. For these validation tests, four different end-member ore types containing different ratios of chalcopyrite, chalcocite and oxidised copper minerals from Rich Metal Group’s Madneuli copper-gold mine, Georgia, were tested. Kinetic flotation tests, including both rougher and cleaner flotation tests, were carried out. The simulations were performed using HSC Chemistry software based on mineral compositions of the ores and kinetic models using rectangular distribution equations and flowsheet model. Simulated and experimental results of copper grade, copper recovery and concentrate mass pull correlated well with R2 values of >0.95. Based on these results, the metallurgical response of different ore blends can be simulated based on the flotation kinetics of end-member ore types. The use of this kind of simulation will create savings during the test work phase and increase the flexibility and predictability in the processing stage. Keywords: Ore body characterisation, geometallurgy, process mineralogy

Jan 1, 2020

By D. A. Cowen

Toll and custom treatment of base metal concentrates have been performed for decades as mines and concentrators are developed distant from capital and, energy-intensive smelting and refining facilities. Commercial treatment terms have been developed and refined for over a century, and are negotiated taking into account a complex array of quality and economic factors. Treatment of third-party concentrates in the South African platinum industry is a comparatively recent development, brought about by the opening up of mineral rights and operations being developed that are smaller than the critical size required to sustain capitalization of smelting or refining plant. Published commercial terms have not been demonstrated to reflect the complexities and subtleties of base metal concentrate markets. This paper outlines some key elements and parameter ranges of base metal concentrate treatment contracts, and applies similar principles to typical Merensky and UG2 platinum group element (PGE) concentrates to determine potential value distribution between the mining and treatment parties in tolling arrangements.

Jan 1, 2012

By K. Thambi

The court in Baleni v Minister of Mineral Resources [2019] 2 SA 453 GP and [2020] 4 All SA 374 (GP), deliberated on the protection of rights of a community holding informal land tenure under Customary Law. The contention related to the necessary level of consent needed to acquire a mining right over such land. Moreover, whether consultations with such communities (Section 23, Mineral and Petroleum Resources Development Act 28 of 2002 (MPRDA) or consent (Section 2, Interim Protection of Informal Land Rights Act, No. 31 of 1996 (IPILRA)) was required to acquire such right. The case has a significant bearing on the granting of mining rights in South Africa, and the discretion of the Minister of Mineral Resources (the Minister) in this regard. However, the objectives of the MPRDA and IPILRA do not dovetail, therefore consultation and consent are not mutually exclusive (Tlale, 2020). This note argues that, despite the resounding victory of this case, the peripheral basis surrounding the decision and the various levels of engagement require serious deliberation. Equally, the degree of reliance on the IPILRA requires clarity to avoid aborting the fundamental objectives of the MPRDA. This paper provides considerations and recommendations that may reduce or eliminate the tensions between the statutory and socio-economic rights in the application of the two statutes.

Sep 1, 2022

By A. Chryssoulis, D. Venter, R. Dunne

An often-overlooked parameter of flotation processing is the impact of surface chemistry. Flotation processing, being a heterogenous process is largely reliant upon the chemistry occurring at the interfaces between solid-liquid phases. Development of analytical techniques such as Auger electron spectroscopy, X-Ray photoelectron spectroscopy (XPS) and low energy electron diffractions (LEEDS) has allowed for a dynamic view characterizing surface composition and structures. The advent of ‘static’ systems, capable of measuring ultra-thin layers on surfaces at low concentrations, was the next step in surface analytical developments. In general, it is the low concentrations and fragmentation patterns which limit the analysis of certain chemical species at plant concentration ranges. At present, analysis of inorganic and organic surface modifiers by time of flight mass spectrometers with a variety of ionization techniques has become a common analytical method to measure chemical species on the outermost surface of mineral particles. By studying the relationship between surface analysis results with metallurgical outcomes, the implications of the presence of surface species can be determined. The presence of flotation activators or depressants can be established using Laser Ionization Mass Spectrometry (LIMS) and Resonant Ionization Mass Spectrometry (RIMS) which are highly versatile surface sensitive analytical techniques. A case study applied to sphalerite flotation in the Neves Corvo Cu-Pb-Zn concentrator and the implication inorganic surface modifiers have is presented. By determining the relative concentrations of Cu, Pb, oxidation products, Ca and other surface species in floated and rejected mineral particles, rationale for improving recovery and selectivity is elucidated. Keywords: Cu-Pb-Zn Flotation, Process Mineralogy, Surface Chemistry, Flotation kinetics

Jan 1, 2020

By I. L. Follington

This paper describes the research and development programme to develop a prototype underground auger mining system aimed at developing and demonstrating an underground auger mining system able to provide economic access to thinner (<1.8 m) coal reserves of South Africa. Data concerning the performance of modern coal augers under South African coal mining conditions were gained from a proven surface auger which operated across a range of coal types. These data were analysed and considered in conjunction with historical information regarding previous attempts at building underground augers dating back to the 1950s. Drawing on these data a prototype underground auger mining system, the BryDet BUA 600 underground coal recovery auger, was designed and manufactured by the BryDet Development Corporation in collaboration with Eskom and Cutting Edge Technology Pty Ltd with support from Anglo Coal and the Ingwe Coal Corporation Ltd. The prototype BryDet BUA 600 underground coal recovery auger commenced trials in March 2000 at the Matla Mine near Witbank in South Africa. The initial trials were undertaken in an open cut to facilitate the commissioning and training associated with a prototype mining machine. A total of 30 holes was augered in the box cut before the machine moved underground. The prototype BUA 600 first achieved the target penetration depth of 80 m in its third hole. The prototype BUA 600 is a new underground mining system which has passed early testing with ?flying colours? and could provide access to extensive underground coal reserves unmineable by conventional mining techniques both in South Africa and elsewhere around the world.

Jan 1, 2001

By M. Frenzel, K. Bachmann, M. Rudolph, R. Tolosana-Delgado, E. Schach, M. Buchmann, L. Pereiraa, K. G. van den Boogaart, N. Kupka

Geometallurgy - the science of predicting the behaviour of ores along the value chain based on their geological and mineralogical characteristics - has barely moved beyond process minerology studies. These studies typically link process behaviour to the mineralogical and microstructural characteristics of pristine or processed ores in a qualitative or semi-quantitative manner. Eventually, a trial-and-error optimisation of the operation is achieved. However, to deliver on its promise, geometallurgy should progress beyond this current approach to a fully quantitative understanding of process behaviour, including the various uncertainties involved, namely predictive geometallurgy. One of the barriers currently hindering this development is the neglect of most ore characterisation data obtained in geometallurgical studies. This is mostly due to the large extent of this information exceeding the capacity of conventional software. To address this challenge, we developed a data mining platform consisting of an SQL database, an R front-end in-house package, and back-ends to interpret data from several analytical instruments. This platform enables the use of the statistical and data mining power of the R open-source environment for any geometallurgical study. Potential applications range from ore characterisation to process understanding and forecasting, and from geostatistical prediction to operational control and optimisation. The scripting abilities of R allow for the: 1) processing of many streams in loops, thus freeing the user from repeating tedious click-and-drop tasks; 2) computation of virtually any derivate or aggregate quantity from the data; 3) distribution of the work among several processor clusters; and 4) keeping of a log file for the calculations done. This contribution presents the building blocks of this platform, and illustrates with several examples its potential to enable predictive geometallurgy. Keywords: Data mining, entropy, kernel methods, LASSO regression, predictive geometallurgy

Jan 1, 2020

By M. Z. Emad, A. Hassan, M. A. Raza, M. U. Khan, S. A. Saki

Digital modelling of a surface is crucial for Earth science and mining applications for many reasons. These days, high-tech digital representations are used to produce a high-fidelity topographic surface in the form of a digital terrain model (DTM). DTMs are created from 2D data-points collected by a variety of techniques such as traditional ground surveying, image processing, LiDAR, radar, and global positioning systems. At the points for which data is not available, the heights need to be interpolated or extrapolated from the points with measured elevations. There are several interpolation/extrapolation techniques available, which may be categorized based on criteria such as area size, accuracy or exactness of the surface, smoothness, continuity, and preciseness. In this paper we examine these DTM production methods and highlight their distinctive characteristics. Real data from a mine site is used, as a case study, to create DTMs using various interpolation techniques in Surfer® software. The significant variation in the resulting DTMs demonstrates that developing a DTM is not straightforward and it is important to choose the method carefully because the outcomes depend on the interpolation techniques used. In mining instances, where volume estimations are based on the produced DTM, this can have a significant impact. For our data-set, the natural neighbour interpolation method made the best predictions (R2 = 0.969, β = 0.98, P < 0.0001).

Feb 6, 2023

COUNCIL The following served on Council during the year under review: Office bearers: Prof D. D. Howat (President), Dr J. P. Hugo and P. W. J. van Rensburg (Vice-Presidents), V. C. Robinson (Immediate Past President) and D. G. Maxwell (Honorary Treasurer). Ordinary Members of Council: H. P. Carlisle, R. C. Espley-Jones, G. H. Grange, Dr D. I. Legge, W. W. Malan, Prof R. P. Plewman, Dr R. E. Robinson, Dr M. D. G. Salamon, L. W. P. van den Bosch and P. A. von Wielligh. Branch Chairmen: A. Bain (Witbank-Middelburg Branch), J. M. Meyer (O.F.S. Branch). Past Presidents serving on Council: R. J. Adamson, M. Barcza, H. Britten, H. E. Cross, J. K. E. Douglas, R. C. J. Goode, P. Lambooy, Prof J. de V. Lambrechts, Dr J. T. McIntyre, J. F. Reid and H. Simon (until March 1972). Ten Council meetings were held during the year with an average attendance of nineteen, and the standing committees held 27 meetings. FINANCE The annual accounts which are attached to this report show an excess of income over expenditure of R21 519. It is very gratifying to be able to report that Council&apos;s efforts to stop the depletion of our accumulated funds are meeting with success. The most important contributors to our surplus this year are symposia and colloquia, sales of publications, Company Affiliate subscriptions and the profit on the journal. While we do not expect continued profits from all these sources in the future we do feel that we are now in the process of accumulating a substantial financial foundation. This will give the Council the necessary confidence to initiate the new developments in the activities of the Institute which are now under consideration. The decision to create a new grade of membership, Company Affiliate, is dealt with elsewhere in this report. There has been a generous initial response from companies and this is the cornerstone of our improved financial expectations. The MacArthur Forrest Memorial Fund shows an excess of income over expenditure of R91 and the total fund was, therefore, increased by this amount to R4 502. The balance sheet shows that the market value of quoted shares and debentures increased during the year from R9 160 to RH 331, which is R2 134 in excess of the book value. Accumulated funds now amount to RH 529 compared with R23 010 a year ago. MEMBERSHIP Sixteen Fellows, twenty Members, six Graduates, nine Associates, twelve Students and twenty-four Company Affiliates were elected during the year. One Member and two Associates were reinstated. Twelve members were admitted to retired membership. Transfers: Member to Fellow, three. Graduate to Member, seven Associate to Fellow, one. Student to Member, one. Student to Graduate, four. Student to Fellow, one. Your Council records with deep regret the death during the year of the following: Dr A. J. Orenstein (Honorary Life Fellow), R. A. Cooper, R. J. Spargo, H. Simon and F. Meyer (Life Fellows), S. D. Loxton, W. P. Arnold, G. C. Needham, W. G. Pyne-Mercier, J. Innes and O. T. Wright (Fellows), E. P. Mennell and O. B. Prentis (Members), J. Brits (Associate). After careful consideration of all the implications it was decided during the year to create a new grade of membership to be known as Company Affiliate, in order that there might be a formal and permanent channel for companies to contribute to the important work of the Institute. As recorded above, 24 companies had joined by the end of the year and many further applications have been received since. We extend a hearty welcome to all our new members. A comparative statement of membership as at 30th June, 1972, and the end of the previous year is shown in the following tabulation:-

By John V. Simmons, Peter J. Simpson

Excavated slopes in open pit coal mines are designed to be as steep as possible consistent with stability and safety requirements. Slope failures occur for many reasons, including oversteepening. This paper is concerned with slope design and excavation experience in the Bowen Basin coalfields of central Queensland (Figure 1), [ ]

Jan 1, 2006

By C. Birch, J. Perold

"Due to the challenging geological environment of the Postmasburg Manganese Field (PMF), a study was conducted to determine if any benefits would derive from the inclusion of resistivity data during threedimensional (3D) modelling of the manganese resource. This was achieved by estimating manganese resources from 2011/2012 drilling data and comparing them with manganese resources estimated from the same drilling data and resistivity data collected during 2013 and 2017.Both models were adjusted to limit their extent to the same 3D modelling space. Significant volume and tonnage differences were observed for all lithological units. The greatest differences were noted in the manganiferous zones of alteration – 7.200 Mt for the geological model versus 3.700 Mt for the geoelectric model.This study showed that the inclusion of resistivity data can reduce exploration costs significantly, as a direct consequence of the resistivity data allowing more accurate siting of boreholes. This decreases the number of boreholes, samples, and analyses required due to the 3D electrical delineation of mineralized areas prior to drilling.An additional benefit is the ability to more correctly forecast the net present value of an operation due to more accurate estimation of manganese resources and stripping ratios. This is clearly demonstrated by the estimated gross profit estimation of R409 million for the geological resource model versus R264 million for the geoelectric resource model.The addition of resistivity data can, therefore, reduce exploration costs and can increase confidence in geological and financial modelling. It would be reasonable to conclude that this approach could also be used for karsthosted massive sulphide deposits. IntroductionAccording to Corathers (2014) and Gajigo, Mutambatsere. and Adjei (2011), South Africa holds between 75–80% of global manganese reserves, followed by Ukraine (10%), Australia (3%), India (3%), and Gabon (2%). The known, land-based, manganese resources located elsewhere are estimated at 2%.The majority of economically important sedimentary manganese ore deposits in South Africa are situated in the Northern Cape Province (Gutzmer, 1996). Manganese ores of the Postmasburg Manganese Field (PMF) were discovered in 1922, and the Kalahari Manganese Field (KMF) in 1940. According to Astrup and Tsikos (1998) and Gutzmer (1996), mining of manganese ore from the PMF ceased during 1989 in favour of the superior quality of manganese ore from the KMF."

Mar 1, 2019

By A. Eitzenberger

This paper describes a study of seismic records from the Kiirunavaara mine footwall which were interpreted in relation with numerical models developed outside the study. Seismic data was retrieved from a portion of the mine and filtered with respect to the ratio between energy carried by an event's P (primary) and S (secondary) waves (Es/Ep ratio), local magnitude, and active mining depth. The data was analysed using Es/Ep ratios and Gutenberg-Richter graphs to determine the event origin, mechanisms, and minimum magnitude cut-off. The magnitude completeness was identified by studying the b-value stability and b-value differentiation between origin sets. It was shown that, by separating seismic events into the origin components shear, complex, and tensile based on Es/Ep ratios, a representative value for the magnitude completeness can be identified for a catalogue with a convex cumulative log curve. The majority of the events were shown to be of shear-slip origin based on the recorded Es/Ep ratios, with pure tensile events constituting only about 10% of the recorded data. Spatial and temporal event location patterns were studied and compared with numerical modelling results. The comparison showed a correlation between shear-slip seismic events and volumes experiencing high differential stresses in the lower part of the footwall. In the upper part of the footwall the results did not reveal any clear correlation between observed damage in drifts and seismic event locations. The concentration of seismic events in the lower portion of the footwall is discussed in the context of rock mass displacements. The results indicate a possible connection between mine seismicity at depth and damage observations in the drifts in higher non-seismic areas by seismic softening and subsequent lateral expansion of the rock mass.

Jan 1, 2017

By C. Dorfling, M. Tadie, S. Grobbelaar

The physicochemical properties of the complex electrolytes used in direct copper electrowinning are an important consideration for the development of a high-fidelity model of the process. Direct electrowinning electrolytes typically contain a high background of metallic impurities. The effect of metallic ions on the properties and accompanying change in the limiting-current density for copper reduction have been the subject of several studies. Although various empirical correlations have been published for describing the physicochemical properties of electrowinning electrolytes, the correlations are only applicable to a limited range of conditions and cannot be extrapolated without further validation. Consequently, in this paper we validated existing physicochemical property correlations for the full range of operating conditions applicable to direct copper electrowinning and developed a new correlation for predicting the associated limitingcurrent density for copper deposition. Following, we evaluated the benefit of using the validated correlations as a component of a dynamic electrowinning model.

Jan 1, 2023

By J. A. Caldwell, G. E. Blight

The metropolitan area of the Witwatersrand has grown up around the Witwatersrand gold mines. Most of the mines have now been abandoned, but deposits of waste material remain and have been surrounded, and in some instances covered, by urban and industrial sprawl. This paper describes the development of geotechnical measures for the abatement of air and water pollution from abandoned gold-residue dams in the Witwatersrand area. The measures include the stabilization of the surfaces of the dams to prevent wind and water erosion, the terracing of slopes to minimize erosion, and the construction of catchment walls and dams. The measures were developed in terms of the set of guidelines for environmental protection adopted by the Chamber of Mines of South Africa in 1979.

Jan 1, 1983

By C. Siyasiya

One of the problems that is occasionally encountered during the continuous casting of DIN 1.4003 stainless steel (hereafter referred to as 1.4003) is the side bulging effect, a problem that is generally prevalent in ferritic stainless steels. This occurs because the unconstrained narrow sides of the solidification shell are not able to withstand the ferrostatic pressure once the strand has emerged from the mould. Coupled with side bulging, there is strand width variation at high temperatures, i.e. when the steel is in the ferrite-austenite dual phase region. Both of these dimensional changes to the slab profile create some processing problems in subsequent hot rolling operations when unacceptable width variations are encountered. The strength of the solidification shell and its ability to withstand the ferrostatic pressure during continuous casting is dependent on its thickness and phase composition when exiting from the mould up to a few metres downstream. From the study of the high temperature metallurgical behaviour of this steel, it was observed that a thicker solidification shell when exiting from the mould and a higher austenite volume fraction in the steel would be favourable for the reduction of the side bulging effect during continuous casting. It was also found that as long as the d-ferrite to austenite phase ratio keeps fluctuating due to variations in chemical composition and process control in the dual phase region from cast to cast, the strand width variation problem would probably persist. The remedy to this effect lies in more strict chemical composition and process control during continuous casting of this steel. The hot ductility experiments revealed that 1.4003 exhibits good hot ductility in the strand straightening temperature range with a minimum of 75 per cent reduction in area and this was attributed to the high volume fraction of ferrite (0.2 to 0.4) in the steel. This would provide a remedy to side bulging by increasing the secondary cooling rate of the strand in order to form a thicker solidification shell without necessarily risking transverse cracking and other surface defects during unbending. Keywords: side wall bulging, resistance bending moment, applied bending moment, ferrostatic pressure.

Jan 1, 2005

By G. Coetzer

"Prior to operating a non-recovery coke pilot plant oven, it was essential to ascertain coal cake stability during the loading of a 1 m3 (1 m × 1 m × 1 m) coal cake into the cold pilot-plant oven by a pusher mechanism. Previously established laboratory-scale compaction parameters, to obtain coal cakes with sufficient stability, were employed during the loading tests of the coal cakes. Two different coals were evaluated, namely Waterberg semi-soft coking coal (sscc) and Oaky North hard coking coal.It was demonstrated that lower applied compaction forces (14%) can be utilized during 1 m3 compaction, in comparison to laboratory-scale tests, to obtain similar wet cake densities, owing to differences in the effect of frictional forces. Wet cake densities for Waterberg sscc improved slightly (3%) to 1.13 t/m3 when utilizing 79 t/m2 applied force for a 1 m3 coal cake, in comparison to laboratory-scale tests. Similar results were obtained for Oaky North hard coking coal, with a 6% density increase to 1.27 t/m3 at a similar applied force. Porosities decreased by 13% and 32% for Waterberg sscc and Oaky North coal, respectively, when 1 m3 compaction was compared to laboratory-scale tests. An opportunity exists to further decrease the porosities of Waterberg sscc during compaction, whereas acceptable compaction parameters were achieved for Oaky North hard coking coal. Most major vertical cracks and the partial collapse of coal cakes were mitigated, and high-stability coal cakes were obtained that could be successfully loaded into the pilot-plant coke oven by a pusher mechanism.Factors contributing to the instability of the coal cake during loading into the oven, such as vertical cracks, are (i) the cubic geometry (1 m3) of the coal cake, (ii) friction exerted by the oven floor, and (iii) mechanical problems, such as a misalignment between the pusher machine feeder plate and the oven floor. IntroductionOperation of the stamp-charging horizontal 1 t electrically heated coke pilot-plant oven at Exxaro Resources requires coal cake stability during the loading of a 1 m3 compacted coal cake into the oven. In this case, a pusher plate is utilized to push the coal cake into the oven over the oven floor. This is in contrast to a ‘spoon’ or bottom plate feeding mechanism as found in industrial horizontal coke ovens. The pusher plate loading mechanism dictates that the coal cake should possess high stability and inherent strength owing to frictional forces exerted by the oven floor. In order to obtain a coal cake of acceptable stability for the 1 t coke oven, various compaction parameters need to be verified and established."

Apr 1, 2019

By J. L. Broadhurst, S. Rumjeet, S. T. L Harrison, T. Chimbganda

Post-mining land use for the production of industrial crops has the potential to mitigate environmental and socio-economic impacts of mine closure and stimulate post-mining economic growth. Fibre-rich plants are of particular interest due to their multi-product potential. In the South African context, where there are many abandoned and end-of-life mines near human settlements, an opportunity presents to assess the feasibility of transforming post-mining land into productive land and building resilient communities through the development of multi-product value chains from fibre-rich plants such as kenaf, hemp or bamboo. This paper provides an overview of the plant selection criteria, phytoremediation potential and the downstream options for the recovery of products and value from bast fibre plants (hemp and kenaf) and bamboo. Based on findings from a comprehensive review of the published literature, as well as interviews with relevant experts within South Africa, it appears that bast fibre plants are the best downstream option for producing ‘green’ textiles and high-end niche products, whereas bamboo is more suitable as a replacement for conventional timber. Although fibre plants have the potential to extract metals from soils, high concentrations may inhibit plant growth and affect the quality of the final fibre product. Further site-specific studies would thus be required to select the best route for both land remediation and optimal product recovery. Keywords: Bioremediation, bamboo, kenaf, hemp, multi-product value chains, sustainable postmining land use

Jan 1, 2020