Search Documents

By Jeff Schwoebel, Dale Evans, Boyd Tangren

The Soldier Canyon Mine (the "Mine") degasification project demonstrates the ability to commercially recover coalbed gas to reduce overall mine costs associated with methane drainage. Gas is recovered from active and inactive areas of the Mine through an underground pipeline and surface compressors. Close inspection of gas quality is required due to potential contamination of air caused by excessive vacuum. Water must be removed routinely to enhance gas removal. This paper will review the operational and production procedures required to maximize gas recovery and insure safety at the Soldier Canyon Mine gas recovery project.

Jan 1, 1993

By Takashi Sakaguchi, Takehiko Tsuruta, Akira Nakajima

Some attempts were made to recover gold from aqueous systems using immobilized persimmon tannin. This adsorbent adsorbed gold from solutions containing hydrogen tetrachloroaurate (III) with high efficiency, whereas there was minimal adsorption from solutions containing gold (I) sodium thiomalate and sodium dicyanoaurate (I). The adsorption of gold was rapid, and was affected by the pH of the solution, temperature, external gold concentration and amount of adsorbent. Adsorbed gold was easily desorbed with 1 M thiourea solution, indicating that immobilized persimmon tannin can be repeatedly re-used for the recovery of gold using adsorption-desorption cycles.

Jan 1, 1995

By Robert G. McLusky

Since 1998, environmental extremists have waged war with the central Appalachian coal industry in West Virginia and Kentucky. In particular, they have filed three lawsuits challenging the legality of excess spoil ‘valley fills’ under CWA, NEPA and SMCRA: 1) Bragg v. Robertson, 72 F.Supp. 2d 642 (S.D.W.Va. 1999), rev’d. 248 F.3d 275 (4th Cir. 2001); 2) Kentuckians for the Commonwealth v. Rivenburgh, 204 F.Supp. 2d 927 and 206 F. Supp. 2d 782 (S.D.W.Va. 2002), rev’d. 317 F.3d 425 (4th Cir. 2003); and 3) OVEC v. Bulen, 2004 U.S. Dist. LEXIS 12690, July 8, 2004; OVEC v. Bulen, 2004 U.S. Dist. LEXIS 16078, August 13, 2004.

Jan 1, 2005

By E. Forssberg, Y. Zeng

Fine crushing and rod grinding have been investigated using a laboratory-scale jaw crusher and a rod mill. The net energy consumption in both crushing and grinding was evaluated from torque measurements. An empirical relationship was established between energy consumption, particle size and operating parameters. When the mill feed size is reduced, through fine crushing, to about 80% passing 3 mm, the energy consumption will be minimized in a comminution chain of fine crushing and coarse rod grinding. The results in fine crushing were compared with a large-scale test.

Jan 1, 1993

By Fathi Habashi

CLAYS CONTAIN the mineral kaolinite, a hydrated aluminum silicate. It is an important potential raw material for aluminum, especially for those countries possessing no bauxite deposits. Therefore, there is no surprise to find a large volume of research done for the recovery of aluminum from clays. Kaolinite (Al203?2 SiO2?H20) contains 39.8% A1203; 46.3 % SiO2, and 12.9 % H2O. The analysis of a good-quality dried clay of an Eastern Canadian siliceous shale is shown in Table 8-1.

Jan 1, 1970

By Jiang Shuguang, Zhang Huicheng, Wang Xingshen

Based on the experience about determination of properties of the main fan in mine shaft, this paper relates at length how to reasonablly select test system, test methods and test instruments, how to appraise the reliability of determination results, and how to effectively control the adjusted air etc. The merits and demerits of the two methods of determining air with Nine- Anemometer and Pitot meter are compared.

Jan 1, 1991

By Dae S. Young, Eleonora Widzyk-Capehart

A quantitative estimation of the size distribution of rock fragments is extremely important in mining, metallurgy and other geotechnical fields. This paper presents a new approach to the analysis of fragmentation. The method combines the practicality of digital image processing of the rock surface with the theoretical volume calculations based on the principles and laws of fractal geometry. The final volumetric distribution curve is compared with the results from traditional sieving indicating close agreement.

Jan 1, 1996

By E. Cetin

The authors describe the general problem of cut-off grade optimisation for multi-mineral deposits and outline the use of genetic algorithms for optimal cut-off grade schedules for deposits with up to three constituent minerals. Case studies are given and a comparison is made with Lane's multi- mineral cut-off grade algorithm.

Jan 1, 2002

By Charles A. Edwards, Kenneth D. Merrill

The Construction of the Northeast Extension of the Baltimore Metro involved soft ground, compressed air tunneling. During the tunneling, gasoline and dry cleaning fluid contamination were encountered. Innovative approaches and solutions were developed to address these problems. Special emphasis was on the problem of compressed air pushing gasoline vapors into surrounding communities, resulting in an extremely dangerous situation and a public relations nightmare. Guidelines and standards were established for working in this contaminated environment. Also, through a proactive approach by all parties, all claims and disputes have been resolved.

Jan 1, 1995

By Henry Brehaut

The International Network for Acid Prevention (INAP) was formed in 1998 by 17 international mining companies to promote significant improvements in the management of sulphidic mine materials and the reduction of liability associated with acid drainage through knowledge sharing and research and development of technology. Since its inception two panels have been formed to identify and move forward with research projects and eight networks have been constituted to initiate interaction and knowledge sharing within the membership in specific areas of technical interest. An INAP web site has been developed to facilitate the sharing of information and to encourage the exchange and development of new ideas.

Jan 1, 2000

For processing plant design it is essential to develop a consistent material and (usually) energy balance as a basis for equipment sizing. This paper discusses techniques for consistent material balance generation, from hand calculation, through spreadsheets to specialised computer programs and general purpose simulations. The appropriate matching of techniques to problem complexity is considered, as are some possible trends for the future.

Jan 1, 1991

By J. B. Yianatos, G. S. Dobby, J. A. Finch, A. R. Laplante, R. Espinosa-Gomez

The question is posed as to why columns typically have a collection zone 10 m high (H) by 1 m in diameter (D). Three geometry dependent factors are considered: degree of mixing, Np; volumetric bias rate, B; and volumetric gas rate, G. Increasing H:D decreased Np and B, which improves performance but decreases G, which causes the column to approach overloading. Taking typical column operating conditions, it is concluded that a collection zone H:D of 10:l is a reasonable compromise.

Jan 1, 1987

By Leopoldo Cortez, Fernando Durão

The dynamic control of a froth flotation section is simulated through a neural network feedback controller, trained in order to stabilize the concentrate metal grade and recovery by applying random step changes to the feed metal grade. The results of the application example show that this controller seems to be sufficiently robust and a good alternative to handle a non-linear process.

Jan 1, 1995

By A. R. Garcia, A. S. Myerson, W. R. Ernst, J. D. Carruthers, M. D. Franke, L. H. Hilzik

A method for removing nickel and vanadium contaminants from spent HDS catalysts involves pretreating the catalyst with H2S followed by extracting the metals with an acidic solution of ferric ion. The ferric ion solution alone removes significant amounts of active ingredients, cobalt and molybdenum; however, by pretreating with H2S, the extraction becomes more selective for removal of Ni and V.

Jan 1, 1988

By Sylvain Duchesne, Claude Bazin, Robert Grant

Grinding simulators are now widely available to assist in the selection of circuit operating conditions or flowsheet designs that yield a given product size distribution. These simulators do not inform of the impact of the grinding product size distribution on subsequent flotation stages. This paper presents a method to predict the effect of fineness of grind on a flotation bank operation. Application of the method is illustrated with data from two Canadian concentrators.

Jan 1, 1995

By Brij M. Moudgil, Ivan U. Vakarelski, Yakov I. Rabinovich

Polymer and surfactant dispersant are widely used to disperse filler particles within a medium. Sur- faces active dispersants form self-assemble structures at the solid-liquid interface. The mechanical properties of the surfactant structures have been determined to strongly influence the dispersion behavior. In this study the atomic force microscope (AFM) is used to determine the elastic modulus and yield strength of a steric dispersant layer adsorbed to a rigid non-deformable surface. To interpret these values a model for elastic body contact based on a modified Hertz theory is applied. The results from this method may aid in the design of application-based dispersant systems.

Jan 1, 2003

By R. L. Grayson

Compliance standards for respirable dust, which are reduced because of high quartz concentrations, have become an industry-wide problem. Research on the physical and chemical character of quartz-classified particles in respirable coalmine dusts indicates that they mine exist in intermixed layers or may be coated by clay or coal material. The relative amount of intermixing varies with the coal seam being mined. If most of the quartz particles of a mine dust are "pure," then the dust may have a high fibrogenic risk potential because of truly free silica and the compliance standard should be lowered. If, however, the quartz is locked inside another material matrix or coated, a reduced compliance standard may not be appropriate.

Jan 1, 1992

By Rick L. Williamson

International lending institutions have charters requiring projects that are seeking loans to adhere to certain environmental performance standards, including compliance with host-country environmental laws, as well as observance of international environmental policies and guidelines. The most commonly applied international environmental policies and guidelines are those established by The World Bank. Lenders require a review by an independent engineer to determine that the feasibility study plans have been developed in accordance with the applicable environmental commitments. Lender agreements require independent engineer evaluation of environmental performance through the construction phase and initial operations phase of the project, culminating in the issuance of an "Environ- mental Completion Certificate."

Jan 1, 2001

By Mayank Srivastava, Satya Harpalani

Production of methane is an inevitable consequence of mining coal. Although the number of mines practicing recovery of methane prior to, or during, coal mining is increasing, ventilation air methane (VAM) is still a significant source of methane addition in to atmosphere. Recent studies have shown that there are ways to recover the VAM energy, while simultaneously reducing the methane emission in to atmosphere. This paper discusses a case study, currently underway, to develop a technique to quantify the VAM emission from a mine. It also presents the different VAM utilization techniques and the suitability of one for the mine being studied. Finally, the paper summarizes the research issues that require further investigation.

Jan 1, 2005

By S. K. Mukherjee, M. M. Singh, N. I. Jayaramn

In underground mining operations, ventilation and water sprays are the common methods of controlling dust. In recent years, there has been a proliferation of technical literature dealing with water sprays for dust control. However, guidelines for the design of an effective water spray system have not been presented to the mining industry. This paper recommends guidelines for water spray systems to control dust in underground mining operations. These guidelines suggest type, number, location, and orientation of nozzles; desirable operating water pressure; and associated filtration system.

Jan 1, 1987