Search Documents

By Abdullah Arik

An ore reserve block model is the basis for various decisions in mine development and production. The block model is initially built using the information from the drillhole data only. Once the mine is put in operation, the information from the blasthole data becomes available. Since the spacing of the blastholes are much closer than the exploration drillholes, the blasthole data gathered from the mine over the years become quite extensive containing valuable information about the deposit. In practice, the information from the blastholes is the basis of determining the ore and waste boundaries between and within mining blocks. In an ore reserve model, the valuation of blocks on and close to the pit face can obviously be improved by using blasthole data from neat by drilled and mined-out blocks in addition to using the widely spaced drillhole data. The ideal basis on which to integrate blasthole and drillhole data is to use cokriging.

Jan 1, 1996

By Michael G. Nelson, Hanguang Wu, V. Izaxon, Sukumar Bandopadhyay

The method of mine ventilation involving heated air, which is frequently used in mines in cold regions, does not correspond to the natural conditions prevailing in permafrost regions; it is not economical and leads to a series of complications which can be prevented or greatly reduced by lowering the temperature of the air stream entering the mine until it is equal to or very close to the temperature of the frozen ground This paper presents ventilation design approaches which can be engineered to provide the required micro-climate and thus en- sure the stability bf the ground for placer mines in permafrost. Specifically three ventilation design approaches are presented: 1) design based on minimum thermal impact; 2) design based on positive/negative heat accumulation in the existing mine airways; and 3) design based on heat exchanging devices such as thermosyphons placed above ground.

Jan 1, 1997

By P. Arell, D. Folkes

This paper presents the basics of EPA’s Hazard Ranking System (HRS), which is used to evaluate sites for possible inclusion on the Superfund National Priorities List (NPL). The paper describes the surface water, ground water, air, and soil exposure pathways and how they are applied to mining sites. Key factors contributing to the site score include the likelihood of a release, waste characteristics, and the targets for each pathway. Waste volumes, definitions of landfills versus surface impoundments, and background concentrations are of particular importance to mining and smelting sites. Because of the presence of metals, large waste volumes, and observable releases, mining and smelting sites often receive high enough scores to be proposed for the NPL based on a single path-way. Neverthess, owners and operators can take steps to reduce the risk of being scored, and to reduce the potential for high scores.

Jan 1, 2004

By Alfred W. Hefferan

A longwall face conveyor system serves the primary function as all material handling systems; i.e., to transport material between the source and its destination. However, the conveyor system must provide many other functions as opposed to the traditional belt conveyor system. In this paper, we will attempt to contrast the longwall face conveyor system with a belt conveyor system. In addition, the unique problems encountered along with the solutions to these problems will be covered. Table 1 lists the characteristics required of each conveyor system. The table demonstrates the contrast in the two systems. Both must be designed specifically to encounter its unique problems. The balance of this paper will explain how the longwall face conveyor is designed to address its requirements.

Jan 1, 2000

By R. L. Unger

Restricted fields of vision are a common problem with underground mining equipment. Also, when lighting systems are provided, they may be positioned where they cause glare. This restricts the visibility around the machines even further. To help address these problems, the US Bureau of Mines has developed a PC-based software package to aid in the analysis of certain human engineering aspects of mining equipment design. The software is available for use by equipment manufacturers and mining companies for design work on new machines, as well as for evaluating proposed modifications to existing machines.

Jan 1, 1995

By E. Topuz, M. J. McPherson, I. M. Konduri

This paper describes experiments conducted to evaluate the effectiveness of jet fans for ventilating blind headings in under- ground mines. A laboratory model of a mine heading was built by using dynamic similarity criteria, and water as the fluid medium. In order to verify laboratory test results, field experiments were designed and carried out in a full scale mine model and in a coal mine in West Virginia. Using CO, as the tracer gas and in combination with a computerized gas monitoring system, tests were conducted to evaluate jet fan performance. The results highlight the flexibility and versatility of jet fans for ventilating blind headings. Numerical modeling of a jet fan in a typical coal mine heading was carried out to evaluate the potential of computational fluid dynamics.

Jan 1, 1997

By R. J. Sweigard, T. Beckman, C. T. Justice, E. D. Thompson, T. C. Hopkins

As a means of permanent disposal, fine coal refuse is often pumped as a slurry into surface impoundments. As the available volume is filled, the embankment heights are frequently increased. The additional embankment material is often placed upon consolidated fine coal refuse. There has been concern about the long-term effect of consolidation of this material at or above the liquid limit on its shear strength. A laboratory investigation was performed using three different types of fine coal slurry taken from central Appalachian coal-preparation plants. The refuse was consolidated in 3-m (10 ft) Plexiglas columns under incremental amounts of surcharge loading. The incremental loads were designed to simulate the effect of increasing the height of a refuse embankment on top of the consolidating coal slurry. After the refuse in the columns had consolidated for several months, the columns were cut apart, and triaxial tests were performed on both the consolidated and unconsolidated material for comparison of their shear-strength parameters.

Jan 1, 1998

By Steven W. Hunt, Ronald E. Heuer, Safdar A. Gill

A 3.3 m (11 feet) diameter, 51 m (168 feet) deep temporary steel casing which had been sunk within glacial soils buckled and collapsed on July 29, 1985. The collapse occurred at the CT-8 Dropshaft site in Milwaukee while two workmen were contact grouting outside the casing in an attempt to stop groundwater inflows through a bottom plug. This paper describes the soil and groundwater conditions at the site, the casing design, the method of shaft construction, and probable causes of the buckling failure. Specific aspects of the paper include: slurry method of shaft excavation and casing installation, soil creep, earth pressure due to three dimensional arching, and buckling strength of a casing surrounded by slurry rather than grout and firm soil. The paper should be of interest to designers and constructors of temporary ground support systems for deep shafts.

Jan 1, 1995

By R. G. Reddy

Chemical and structural changes occurring during the roasting of refractory gold ores were investigated. Effect of temperature on oxidation behavior of ores was analyzed using TGA, DTA and X-ray diffraction methods. The experimental results showed that the carbon in the ore has to be oxidized to a minimum value before any appreciable oxidation of sulfur occurs. Oxidation rates as a function of temperature were calculated. Optimum conditions under which a successful roasting of the refractory gold ores can be obtained are discussed.

Jan 1, 1990

By P. C. Thakur

The history of coal mining in the United States of America and the rest of the world is replete with mine explosions and consequent loss of lives. Serious efforts in the USA to recover methane prior to mining and post mining started about forty years ago. CONSOL Energy Inc. and government agencies, e.g., the erstwhile US Bureau of Mines developed several techniques of methane drainage, such as in-mine horizontal drilling, vertical gob wells, hydrofracing of vertical wells and horizontal drilling from surface. With the current technology, thirty to sixty percent of total methane emissions from a mine can be captured making the mines much safer and more productive. Drained methane is often marketed to defray the cost of methane drainage. This paper is an anthology of these developments and describes how coalbed methane, which used to be a bane, has become a boon for the coalmining industry.

Jan 1, 2003

By ev, Ze&apos Reches

The growth of networks of shear fractures is explored in a series of experiments with samples of wet clay. The samples are subjected to plane strain deformation in a rigid apparatus. The individual fractures observed on the upper surface of the clay samples grow longer by three mechanisms: in-plane propagation, off-plane propagation and coalescence. New, active fractures cut and displace older, less active ones. The lengths of individual fractures display lognormal distribution in most cases and power distribution in fewer. The calculated length parameters in the experiments, as well as in three field cases discussed here, suggest that the fundamental parameters in fracture analysis are the normalized cumulative length and the length of the shortest fracture measured.

Jan 1, 1986

By Shoung Ouyang, Pinnaduwa H. S. W. Kulatilake

Available literature on the topic is reviewed. Methods are suggested to improve the presently available techniques to perform probabilistic modeling of shear strength parameters for rock discontinuities. The Mohr-Coulomb model and a power law model are used as strength criteria to model shear strength of rock discontinuities. Use of various regression techniques for point estimation of shear strength parameters from direct shear data are discussed. Goodness-of-fit tests for bivariate beta and bivariate normal distributions are developed, and the applicability of them to represent the distribution of shear strength parameters is tested through examples. Both distributions seem to have potential to represent the statistical distribution of strength parameters.

Jan 1, 1986

By Robert L. Cascio

The mining industry uses a large amount of electric power. Their equipment is subject to extreme environmental conditions and mechanical shock. A significant number of electrical accidents are a result of improperly grounded electrical equipment. Federal regulations require the safety ground bed resistance to be measured once a year or after modifications. Most commercially available instruments used to measure the ground bed resistance require the ground conductor to be disconnected and the power system disconnected for safety reasons. The "fall of potential1' method requires auxiliary ground rods and approximately two hours to complete the test. Although a new instrument was initially thought to measure the ground bed resistance immediately without isolating the ground bed, field tests have shown this method is not accurate. In some cases, a continuous measurement of the ground resistance is desired. A monitor has been developed and is presently being evaluated at several mines. These installations will be discussed.

Jan 1, 1992

By K. Taniguchi, Y. Inada

When underground openings are excavated in rock mass for storage of Liquefied Natural Gas, hereinafter referred to as L.N.G., as its temperature is -162o C, steep temperature gradients and thermal stress occur around the openings. That is, the plastic zone and cracks around openings will expand with time. In this paper, the range of cracks which were obtained by the Crack Analysis Method and the range of the plastic zone which was obtained by the No Tension Analysis Method were investigated and compared.

Jan 1, 1986

By S. Finsterle, R. C. Trautz

Numerical modeling studies were performed to investigate water seepage into underground openings excavated in unsaturated fractured rock. Water seepage is an important factor affecting the performance of a nuclear waste repository, such as the one proposed at Yucca Mountain, NV. The amount of water dripping into an underground opening depends on the connectivity and permeability of the fracture network, as well as on the capillarity of individual fractures intersecting the opening. A high-resolution numerical model of an unsaturated fracture network was developed, and the appropriateness of seepage predictions using a fracture-continuum model was examined. Model calibrations to liquid-release tests performed at Yucca Mountain are also discussed.

Jan 1, 2002

By J. H. Kempton, D. Atkins, W. Locke

The scrutiny given to model predictions of pit-lake water quality has focused attention on the uncertainty associated with long-term predictions. Although comparison of probabilistic predictive modeling of water quality in existing pit lakes suggest that short-term predictions can bracket most parameters, un¬certainties in wall-rock reactions and the stability of groundwater composition and climate remain unquantified This overview of the uncertainties associated with longer-term predictions is presented as support for those considering policy decisions that must be made in the absence of reliable estimates of future conditions.

Jan 1, 2000

By A. Marabini, J. Cases, M. Barbaro

Outlined is a review of the application of new selective chelating reagents as flotation collectors; calculation methods for the selection of chelating structures, limitation of the function of commercial chelating agents as collectors, and the synthesis of two new classes of chelating collectors with mixed aliphatic-aromatic structure for oxidized lead-zinc ores. Given are: examples of substituted mercaptobenzothiazole and aminothiophenol structures, flotation and adsorption study of an alcoxyl-mercaptobenzothiazole on cerussite, comparison of adsorption of conventional and chelating collectors, study of the influence of the aliphatic structure1 component on the collecting power of chelating type reagent and the design of chelating collectors with optimal structure.

Jan 1, 1989

By R. L. Grayson, Y. J. Wang

An integrated approach to the management of underground coal mine production and cost is presented. A conceptual model for objectively analyzing an underground mine to obtain lower cost and higher productivity from operations is outlined. The model is designed to provide mine managers with a quantitative, decision-assisting methodology that can be used in formulating timely responses to fluctuations in operations. It consists of a productivity fore- cast component, routine use of current resource consumption factors, a linear programming scheduling component, a manpower loading analysis, and an inventory control component. The model is applied to an underground coal mine.

Jan 1, 1990

By Wayne A. Sadik

The mine ventilation system of the Henderson Mine provides a case study of designing and maintaining high-quality respirable air in a large underground mine with over 200 units of diesel-powered equipment. This system was designed with concern for minimizing exposure to personnel of siliceous dust, diesel exhaust, smoke, and potential fire hazards while optimizing general environmental air quality throughout the multilevel/multiheading operation. As a relatively new operation, the Henderson Mine incorporates a modern ventilating plant and mine de- sign as well as state-of-the-art technology where appropriate. Two main ventilation shafts approximately 2,300 ft (701 m) in depth (one intake, one exhaust) will handle 1.8 million cfm (850 m3/s) of air circulated throughout 60 miles (97 km) of drifting, providing the ventilation requirements for more than 25,000 diesel horsepower (18,642 kw) underground.

Jan 1, 1980

By P. V. R. Bhaskar Sarma, P. K. Sahoo, G. Roy Chaudhury

A process was developed to treat an ammoniacal leach liquor containing zinc using Di (2-ethyl hexyl) phosphoric acid (D2EHPA) as the extractant. The objective of this work was to develop a process package for the treatment of complex sulfide leach liquors. Zinc extraction could not be carried out directly from the ammoniacal solution in mixer-settler units because of crud formation and low extraction efficiency. After neutralizing the free ammonia with H2SO4, the extraction efficiency was only about 40%, due to the high concentration of (NH4)2SO4. To decrease the (NH4)2SO4 concentration, the free NH3 was steam stripped, and the resultant liquor was subjected to zinc solvent extraction. An extraction efficiency of 98% could be achieved by controlling the equilibrium pH. Stripping studies were also optimized after removing ammonia from the zinc-loaded organic. A continuous 100-hr operation that included extraction, scrubbing and stripping, was carried out successfully.

Jan 1, 1995