Search Documents

By St. E. Deák

There is a large preoccupation concerning the development of expert tools (ET) in the mining industry, in order to minimize the impact from waste dumps and processing residues on the environment. In this paper, the authors present a new approach for the development of an expert tool for each area under study, in order to minimize production and disposal of mining wastes on the environment, by taking into account the DKRControl method as well as the Ecomining principles, regarding among others hazard identification, impacts and monitoring. Due to the complexity of this topic a reliable ET requires input from a number of interested stakeholders. The design and management of a mining waste disposal site over its entire life cycle is also considered very important.

Jan 1, 2008

By Jean-Pierre Nossereau, Allen J. Hulshizer

The main thrust of this paper covers the design, installation techniques and experience associated with the installation of eleven 1.5 m (4'-11") and three 2.87 m (9'-5") diameter shafts in 15 to 23 meters (50 to 75 ft) of water over 1.6 Km (a mile) out in the Atlantic Ocean. The approach implemented, permits the use of pre-fabricated shaft linings and incorporates a safe dry-tap method for connecting the offshore shafts to tunnels driven blind from deep land shafts over 4.8 Km (3 miles) away. This tunnel-shaft system is a unique venture employed at the Seabrook Nuclear Power Station to meet plant cooling water requirements.

Jan 1, 1981

By Michael G. Nelson, Sekhar Bhattacharyya

Between 1974 and 1977, a detailed study of coal pillar strength was conducted by the University of Utah at the Beehive mine in southeastern Utah. This study was funded by the U.S. Bureau of Mines, and included laboratory testing of coal samples, extensive field instrumentation and measurements, and finite element analyses based on the laboratory results. Recently, a similar analysis of the laboratory results and mine design geometry was completed using the LAMODEL program developed by NIOSH. The results of this analysis were close to the data collected in the field. This study allows comparison with the earlier finite-element analysis, and illustrates the utility of the LAMODEL software suite.

Jan 1, 2005

By B. C. Cornilsen, X. Shan, D. H. Carlson, J. H. Johnson

Airborne respirable Diesel Particulate (DP) presents an additional health hazard in that it has been shown to be mutagenic. This problem is of increasing concern as more coal mines introduce diesel vehicles. If the DP present in coal mine air is to be controlled it must first be measured. This paper describes development of the laser Raman spectroscopic measurement of the amount of DP in DP/coal mixtures collected on filters in the laboratory and in coal mines. The Raman technique provides a chemical measure of the carbonaceous material in each component, and is not dependent upon particle size. When this work was begun there were no known analytical methods for this measurement. Side-by-side in-mine comparisons of the results obtained from Raman, neutron activation analysis, and size selective analyses (MOUDI and personal samplers) are presented. The neutron activation and size selective analyses were obtained by the USBM Twin Cities Research Center and University of Minnesota. Good agreement has been found among these three methods.

Jan 1, 1991

By E. Azrag, A. MacDonald

A hydrogeologic investigation was conducted to predict inflow to underground mine workings and mining-induced hydrologic impacts for a proposed underground mine beneath a lake in northern Canada. Flow and shut-in tests were conducted to determine hydraulic conductivity values and to estimate the hydraulic head. A conceptual hydrogeologic model was developed and incorporated into a numerical ground-water flow model (utilizing MINEDW, a three-dimensional, finite-element code with special attributes designed for mine dewatering). The mining sequence was represented in detail(e.g., driving ramps and drifts, extracting panels, and backfilling mined areas). Due to limited field data, a quantitative assessment of uncertainty was implemented to estimate limits of possible inflows.

Jan 1, 2003

By J. Cassells, N. Chrisman, R. Arnold, P. Rusin, L. Quintana

Toxic substances in On solutions can retard biological leaching of sulfide dump ores. On solutions were ana1yzed for metals, organics and chloride and showed inhibitory concentrations of aluminum, manganese and chloride. Inhibition of bacterial activity by the solid fraction of On solution with and without the organic constituents, was evaluated. Bacterial toxicity was evaluated by monitoring bacterial numbers, pH, Eh, and rates of iron oxidation. The On solution solids were toxic at 50% to 60% of their field concentration. Most of the toxicity of the On solution was due to the organic fraction. Different solvent extraction (SX) reagents show varying degrees of inhibition of T. ferrooxidans. Bacterial inhibitory effects of carriers and lixiviants used in the SX plant should be determined so that entrained SX reagents do not retard biological dump leach systems. The reagents used should be the most cost-effective and the least toxic.

Jan 1, 1996

By A. J. Surtees, M. P. Evans

This paper discusses the development and application of sophisticated monitoring equipment used to measure the operating parameters of conveyor systems. With the radical reduction in price of computer hard- ware and software during the last decade and an associated increase in memory capacity, the concept of continuous conveyor monitor is now a reality. With this tool, the various problems normally encountered in large conveyor installations can now be avoided at an early stage. • The four main areas of application are: • Design verification • Hand-over certification • Preventative maintenance and increase of system availability Failure analysis The paper introduces the techniques used and gives examples where the service has been used.

Jan 1, 1996

By John E. Urosek, Herman Schade

In March, 1988, a fire occurred in a large underground coal mine. Coal Mine Safety and Health of the Mine Safety and Health Administration was immediately notified of the situation. They requested the assistance of the Pittsburgh Health Technology Center (PHTC) to provide monitoring and analysis of the mine atmosphere in and around the fire area to insure the safety of the miners escaping from the mine and for the miners involved in extinguishing the fire. The capability to provide this type assistance is maintained by the PHTC Offices located at 4800 Forbes Avenue, Pittsburgh, Pennsylvania. The equipment used is maintained field ready and can be mobilized almost immediately. This paper will discuss the response to this recent major mine fire.

Jan 1, 1989

By A. E. Stewart

Slope design in an open pit mine includes determining bench height, bench face angle and berm width. Case histories are presented of two highwall slopes (160 and 220 m or 525 and 720 ft high) excavated in dipping strata in an op¬erating coal mine. These examples illustrate the influence that bench face angle can have on the stability of an entire slope. The two highwall slopes, the lower of which experienced significant instability, were excavated in approximately the same lithologic and structural environment. The main differences between the slopes were the angle at which the bench faces were excavated and the excavating methods that were used. Relevent aspects are also described of the engineering geology, slope design and excavation procedures.

Jan 1, 1998

By B. Cristol, G. Benier

Laboratory and pilot tests have shown that the grinding of some aluminas makes two populations appear : agglomerates’ and ultimate crystals’. Classical breakage functions (Size Mass Balance Method) aren't able to describe correctly this kind of grinding. So we have optimized a particular breakage matrix which takes into account the fact that the agglomerates can either be reduced in size or either be blown up to liberate the ultimate crystals. The models which were developed using this breakage matrix are in good agreement with the experimental results of the pilot tests. The industrial breakage functions were estimated from pilot breakage functions, using scale up prediction procedures and plant tests. The agreement between predicted and actual plant performance is excel1ent.A 20 % increase in capacity was predicted to be available by improving the grinding circuit classifier performances.

Jan 1, 1992

By E. William Rossi, Audrey F. Glowacki, Richard L. Unger

The U.S. Bureau of Mines has developed a graphics-based computer model to assess operator visibility for continuous miners, shuttle cars, and scoops. Using digitized drawings of the machine, the program can analyze visibility for both 5th percentile female and 95th percentile male operators. This model was used to predict 95th percentile male operator visibility for two shuttle car designs. These results were then compared to those obtained from a manual assessment of visibility using the actual shuttle cars. The methods showed good correlation except for several cases which were attributed to imprecise digitization of the machines.

Jan 1, 1992

By B. J. Arnold

Coal blending inherently means homogenizing a mixture of coals so that the properties of the blend meet some specifications for maintaining power plant performance and emission requirements. In practice, however, coal blending is, at best, coal mixing. The degree of blending sophistication required depends on the reason for coal blending in the first place. If it is to maintain fuel characteristics that will diminish the chance of slagging and fouling, then some swings in variability may be tolerated at some power stations. However, if emissions limits are the issue, then more sophistication may be needed. Emissions limits are becoming stricter with requirements to meet averages for shorter time frames (hours and days instead of weeks and months). These restrictions require closer control over the quality of the blend being fed into the bunkers at the station. Even scrubbed units should have a consistent quality of fuel as feed so that sorbent additions can be minimized. To meet these challenges, engineers must consider available equipment and control techniques and the properties of the parent coals when evaluating new blending systems.

Jan 1, 1994

By Don W. Murphy, Don M. Larsen

Advanced process control has been implemented at the Jerritt Canyon Mill. Plant production prior to 1997 was limited by grind circuit capacity. The installation of additional mill horsepower and an optimizing supervisory control system achieved a throughput increase in excess of 12 percent. The controller application utilized a seamlessly integrated fuzzy logic expert system for real-time mill control coupled with a neural network predictor for closed-loop feedback of particle size constraints. In late 1998, a second supervisory controller was installed to operate the fluidized bed roasters. The second controller optimized roasting conditions, increased plant throughput and improved metallurgical recovery.

Jan 1, 2000

By C. L. Schneider, R. P. King

Size distributions and liberation spectra were measured in samples taken from 10 streams in a taconite milling circuit under normal operating conditions. The size distributions were deter- mined by sieving and the liberation spectra by image analysis using the linear-intercept method with proper stereological correction. The measured data were used to validate a simulation of the milling circuit using MODSIM which included the calculation of both size distributions and liberation spectra. Both the measured data and the simulator showed that liberated magnetite was returned to the mill in the cyclone underflow. The simulation will be used to improve the economic performance of the plant.

Jan 1, 1995

By M. S. Celik, A. Aslanbas, B. Pehlivanoglu, R. Asmatulu

The principal impurities in some feldspar ores are titanium and iron, which impart color and degrade the quality of the ore. Mineralogical investigations indicate that, while titanium originates mainly from rutile with small amounts of sphene, iron originates mainly from mica minerals. Fatty acids, particularly oleic acid, are extensively used, with reasonable success, in the flotation of colored minerals from feldspar ores. In this study, potassium oleate, oleoyl sarcosine and hydroxamate were used to float colored impurities both before and after magnetic separation. Oleoyl sarcosine is found to exhibit better results compared to other reagents. Magnetic separation followed by flotation is found to produce a feldspar concentrate of superior grade.

Jan 1, 2002

By W. E. L. Minter

The most important Witwatersrand gold placers occur on extensive unconformity paleosulfaces that were produced during protracted periods of fluvial degradation. The erosional etches on what was generally unlithified sub-strate indicate that low sinuosity erosion patterns prevailed. The transport systems were dominantly braided fluvial with a minor debris-flow component. The placer sediments were non-cohesive sands and gravels. They were evidently transported by fluctuating, yet perennial, discharges across extensive, low relief braid plains, not far from littoral environments. Progress made in understanding heavy mineral transport processes now emphasizes the importance that selective entrainment probably had in producing concentrations. Cognizance that these characteristics are not unique to the Witwatersrand should be taken into account when designing exploration models.

Jan 1, 1991

By J. H. Tylczak, R. Blickensderfer, D. J. Singleton

As part of its research on wear of mining and mineral processing equipment, the US Bureau of Mines evaluated the erosion-corrosion characteristics of 12 alloys in phosphoric acid waste water. Tests were conducted on 2- and 5-cm-diam specimen8 in 12- and 60-cm-diam ball mills by grinding phosphate rock in gypsum pond water with an initial pH of 1.6. For comparison, grinding tests also were conducted in tap water. Static corrosion tests in gypsum pond water also were carried out. For all alloys tested, the wear by erosion-corrosion was greater than the sum of erosion plus static corrosion. A low-alloy, high-carbon steel and a high-manganese, nitrided stainless steel were the most cost-effective materials

Jan 1, 1987

By B. van der Moolen, P. J. M. Groot

The introduction of liberalisation in Dutch mineral provision has created a lot of uncertainty on how and where to supply for the need of construction raw materials. Some possible effects of this policy shift are: 1. the extraction of materials from small pits with truck transport, 2. an increasing dependence on foreign suppliers, 3. the usage of marine dredged materials, 4. more input of secondary substitutes. The outcome of this policy and the resulting marketbehaviour have consequences for transport and infrastructure and hence for sustainability issues. Mineral provision, on the other hand, is also influenced by the availability of infrastructure. Insufficient transport capacity could hamper the development of mineral projects that render benefits to society. (Even) in a liberalising market for mineral provision, the central and local governments have an important role to play with regard to infrastructure and the effects of transport. Various trends point towards an increasing internationalisation in mineral provision. What will increasing trade and increasing influence of the market mean for transport infrastructure? How should increasing transport be judged with respect to sustainability? In the sustainability discussion these questions will have to be answered on a national as well as on a European scale.

Jan 1, 2005

By R. D. Kelsey

The theory, definition and practical application of cutoff grades have evolved over a long period. This evolution is reflected in the continuing flow of papers on this and other related matters though the rate has varied as new ideas and theories have become understood and applied in practice. Papers by Lane(l) in 1964 and Taylor(-2)- in 1972 provided landmarks in the understanding and general communication of cutoff grade theory and its application. The reasons for the continuing interest in cutoff grades are obvious. Too high a cutoff can reduce the mineral recovered and possibly the life of a deposit. Too low a cutoff would reduce the average grade (and hence profit) below acceptable levels. This paper provides a brief overview of existing cutoff grade theory and some particular aspects of its application.

Jan 1, 1979

By Selamet G. Ercelebi, Mahmut Yavuz

An inherent aspect of longwall mining is moving the equipment from a mined-out panel to a newly developed panel. Moving times may be reduced by detailed preplanning. A very useful tool for planning is MS Project. Using MS Project, one can efficiently plan, manage and coordinate a project from conception to conclusion. The critical path analysis identifies potential critical activities which may cause excessive time delays. Changes to the tasks on the critical path can have significant impact 0.n the completion of a project. Assigning additional resources to these tasks (either moving labor from other tasks to critical tasks or providing labor overtime work) may reduce the move time. Simultaneous activities are the candidates for moving the labor from an activity to another. Each time a change is made, the critical path should be recalculated. MS Project quickly recalculates schedules and lets you see how changes in one part of the project will affect the overall plan. In this fashion it is possible to minimize the longwall move time.

Jan 1, 2002