Search Documents

By H. K. Lin

Cyclic voltammetric and potential step chronoamperometric techniques were used to study gold dissolution in cyanide solution. Three distinct anodic peaks and one cathodic peak appear on the voltammogram between -0.50 and 0.80 V vs. SCE. The corresponding reactions were proposed to explain the peaks and the passivations. The proposed reactions were in agreement with the effect of pH and cyanide on the magnitude of the peak currents. Cyclic voltammetric tests, with various vertex potentials, were also conducted to examine the proposed reactions. Steady-state currents at various potentials were obtained by potential step chronoamperometric technique and were compared with transient currents obtained by the cyclic voltammetric technique.

Jan 1, 2002

By Fred N. Kissell, Robert J. Timko

Safe escape from coal mine fires continues to be a concern of the mining industry. The most life-threatening fires occur outby the working sections. Because stoppings always leak some air, an outby fire may in time cause intake escapeways to become contaminated with smoke and toxic gases. Smoke and gas infiltration into intake escapeways can be minimized by raising their air pressure over that of adjacent airways. This can be done by checking off the intake escapeway near the working face. The Bureau of Mines has investigated the use of a parachute stopping as a quick-erect check curtain during mine fires, and the concept has been tested in several mines. In every instance, when a parachute stopping was erected on the section, the intake pressure went up substantially. The pressure-raising effect of the parachute persisted for up to 1200 m (4000 ft) outby. Results indicate that checking off the intake escapeway may serve as a viable way to improve safety during mine fires.

Jan 1, 1991

By M. H. Kotze, M. J. Virnig, G. Steinbach

Earlier work at Mintek on the development of gold-selective resins culminated in a plant-manufactured batch of the first generation of Minix resin. A subsequent pilot-plant campaign at a South African gold mine identified some problems with that resin. These included lower capacity and selectivity for gold compared with the laboratory prototype, and a slow but progressive loss in capacity as the resin was eluted and reloaded cyclically. These problems were overcome by chemical modification of the resin structure. Examples of these improvements are presented. The commercialization of a new resin for a new metallurgical application presents problems, which are exacerbated by the initial lack of demand for the resin because the process is unfamiliar to the mining industry. Progress in the commercial development of Minix is discussed in this context.

Jan 1, 1993

By O. A. Bascur

The problem of setting the proper control objectives and/or having several objectives to be met in the implementation of grinding control strategies can be resolved. The design and implementation of a distributed control system for safe operation of a grinding circuit while maximizing profit is presented. An optimal recovery through- put target for a desired grind is accomplished by advanced control strategies at the DCS level. A mill load constraint control technique provides stable operation with a substantial increase in throughput, while the desired grind index is maintained by an inferential grind control technique without using a particle size analyzer. The integration of crushing/grinding and flotation in the overall design was the key to the success of the project. This synergistic effect was obtained by implementing a computer plant management system in the concentrator. The overall/philosophy was to keep the implementation simple while using new technology creatively.

Jan 1, 1991

By Gregory W. Gustina, Terry P. Boyle

Analysis of the structure of the benthic macroinvertebrate community, consisting of the number of taxa and the relative distribution of total numbers, is a routine method of assessing the ecological quality of streams. Various multivariate statistical techniques, which assess the structural variability of the benthic macroinvertebrate community and the relationship of that variability with natural and anthropogenic environmental variables, have utility in separation of the various physical and chemical factors associated with impact. Multivariate methodology, while computationally complex is statistically rigorous and better integrates physical, chemical, and biological data for more synthetic interpretation. Using the multivariate analysis technique, canonical correspondence analysis, we have analyzed a number of sites in the upper Boulder River Basin, Montana to determine which are the important environmental variables associated with variation in community structure. The results of this analysis an integrated with more traditional analysis of community structure and incorporated in a risk analysis for the mediation of abandoned mines and mill sites within the watershed.

Jan 1, 2000

By W. D. Diment

The concept of flying employees in and out of remote mine sites on a regular rotation basis, rather than establishing permanent support communities nearby, has gained increasing acceptance by mine operators, unions and regulatory agencies in Canada. The development of successful fly in/fly out programs and resultant compressed work schedules is dependent on meeting design requirements through comprehensive research of worker profiles to ensure the selection of suitable employees and the implementation of satisfactory working conditions. This paper presents an overview of Canadian mine industry practice with regard to the fly in/fly out mode of operation and compressed work schedules.

Jan 1, 1987

By Peter J. Suardini

Over the last few years, researcher have been working on improving procedures for fine-coal (minus 150 microns) washability analyses. The effort was stimulated by past difficulties in obtaining accurate and reproducible results from the various commercial laboratories providing fined washability services. This paper contains the results from fine-coal washability testing, performed by Process Technology, Inc. (PTI), as part of a U.S. Department of Energy (DOE)-sponsored project. The testing focused on comparing the performance of a number of media options (i.e., aqueous solutions and organic solvents), as well as evaluating the impact of a number of procedural steps on separation performance. The paper summarizes PTI's recommended washability procedures for various size fractions and ranks of coal, and makes recommendations for future studies of certain phenomenon, such as void penetration and particle density changes, which are not well understood.

Jan 1, 1995

By I. Nishkov, L. Alexandrova

The kinetics of froth flotation and the three-phase contact (TPC) parameters are studied at temperatures varying from 20°C to 40°C. The material floated consists of glass spheres and a quartz particles with various diameters. Dodecylamine hydrocloride (DDAHCI) is used as a collector. The equilibrium three-phase contact angle is measured with a microscope technique using the modified Mingins-Scheludko method. Using a Wilhelmy method, the temperature effect on the surface tension of the DDAHCI solution is determined. The formation of the thin film on a polished plate of vitreous silica and the expansion of TPC is monitored by means of a metallographic microscope and recorded on a attached camera at different temperatures. The experimental data show an intensification of the flotation kinetics at 30 and 40°C in the case of small particles. Such an intensification is not observed with the larger particles. The cause for intensification of the flotation kinetics is sought for in the dependence of the TPC rate of expansion and induction time on temperature.

Jan 1, 1995

By R. M. Cox

Pneumatic coal loading and conveying systems provide alternative methods for the safe and efficient mining of the thin, high-grade coal seams found in the Southern Appalachians. Pneumatic systems eliminate most of the health and safety hazards associated with the operation of conventional mining and haulage equipment in small low-coal mines by removing powered mobile equipment from the mine. Ventilation is also improved by the coincidental removal of gas and respirable dust from the mine by the operation of the pneumatic loading and conveying system. Other significant advantages of pneumatic coal recovery systems are relative simplicity, operating flexibility, low capital cost, quiet operations, environmental benefits and ease of automation. The design considerations and field evaluations of experimental prototype pneumatic coal loading and conveying systems installed and operated in small thin-seam mines are presented in this paper. In addition, fundamental design criteria and recommendations for the installation and operation of a variety of pneumatic coal loading and conveying systems that offer alternative coal-recovery systems that alleviate the serious health and safety concerns of current small mine operations are proposed.

Jan 1, 2000

By S. Kelebek, S. O. Fekete

The flotation process developed at Falconbridge laboratories utilizes sulphur dioxide and diethylenetriamine (DETA) reagent combination in the depression of pyrrhotite to allow its separation from pentlandite and chalcopyrite. DETA by itself has failed to produce flotation selectivity with samples from plant and pilot plant streams which showed relatively high redox potentials. However, DETA was found to function effectively on laboratory-generated samples under certain conditions. The results of poor depression are in keeping with thermodynamic calculations which indicate that in the presence of sufficient xanthate and DETA, the formation of ferric dihydroxy xanthate and dixanthogen is possible under oxidizing conditions. The use of sulphur dioxide alone has also resulted in a rather poor depression of pyrrhotite. However, the combined use of these reagents has resulted in an efficient and consistent separation of pyrhotite from pentlandite and chalcopyrite. Various aspects of this selective flotation system are presented along with a discussion on possible operating mechanisms.

Jan 1, 1995

By John R. Twining, Michael D. Lawton, Ross A. Jeffree

The Finniss River system in tropical northern Australia has received 'acid-drainage' contaminants from the Rum Jungle uranium/copper mine site over the past 4 decades. Following mine-site remediation that began in 1981-82 the annual contaminant loads of sulfate, Cu, Zn and Mn have declined by factors of 3, 7, 5 and 4, respectively over 1990-93, compared to the 1969-74 pre-remediation loads. Comparison of the frequency distributions of contaminant water concentrations over these pre- and post-remedial periods have shown varying degrees of reduction in the highest levels following mine-site remediation, that are consistent with reductions in their annual-cycle loads. Among the three selected major metal contaminants the reductions in maximum water concentrations are most pronounced for Cu. The demonstrated reductions in the highest water concentrations of all four contaminants are also associated with previously reported ecological improvement in the Finniss River system, compared to the benchmark of environmental detriment established in 1973fl4, prior to the beginning of remediation at the mine site.

Jan 1, 2000

By S. G. Malghan

This paper reviews uses of sodium sulfide in the flotation of oxide minerals of copper, lead, and zinc. The activation and depression effects of sodium sulfide are of particular importance because of their applications with oxidized lead and copper ores. In spite of its industrial importance, the nature of the heterogeneous reactions between sulfide ions in solution and the surface of oxidized minerals has not been fully understood. Hence, proposed mechanisms of the sulfide action in flotation, methods of measuring and monitoring sodium sulfide in flotation pulps, and variables influencing the sulfide addition are analyzed. Recent studies on sodium sulfide addition to flotation pulps, monitoring its concentration, and the optimum dosage control using platinum and/or sulfide specific ion electrodes are discussed.

Jan 1, 1987

Ever since A Decade of Digital Computing in the Minerals Industry was published in 1969, mining men have expressed the need for an additional reference on computer methods. It was felt such a volume should spell out the "how to" of computer applications in the solution of their problems. Computers in the minerals industry will be 20 years old when the 1979 SME Fall Meeting and the 16th International Symposium on the Application of Computers and Operations Research in the Mineral Industry (APCOM) take place jointly in Tucson, AZ. On such an occasion it was thought appropriate to publish an anniversary volume which reviewed current practices and projected what might prevail as computer methods for the future. Thus was born the idea to publish Computer Methods for the 80's. The first planning meeting for this volume took place in Las Vegas, NV, during the 1976 annual meeting of the American Institute of Mining, Metallurgical, and Petroleum Engineers. It quickly became evident that no single computer method existed to solve most mining problems; rather, mining computer methods are generally tailored to fit unique geologic, mining, and organizational conditions. Hence a format which included both the theory and practice for each of the computer applications was adopted for this volume.

Jan 1, 1979

By Mark J. Schultz, William J. Francart, Gary J. Wirth

Atmospheric Monitoring Systems (AMS) utilizing carbon monoxide sensors have demonstrated their superiority over thermal type fire sensors for early fire detection in underground coal mines. After proving their capability and dependability throughout the 1980's, systems are now evolving and applying new technologies to enhance their effectiveness and reliability. The use of AMS in coal mines which utilize diesel equipment presents unique obstacles. Exhaust gases from diesel equipment not only raise mine ambient CO readings, but also cause numerous nuisance alarms. Both of these conditions reduce the effectiveness of the AMS. New technologies, such as discriminating devices, smoke detectors, and time delays, as well as administrative controls, have been developed and are being utilized to help reduce nuisance alarms produced by the diesel exhaust. This paper will discuss these technologies and administrative controls which are being utilized in coal mines to enhance the effectiveness of the Atmospheric Monitoring Systems. Reference to specific products does not imply endorsement by the Mine Safety and Health Administration.

Jan 1, 1995

By Frank L. Bazzanella

Se presenta una breve introducción de la concentración gravimétrica, incluyendo alguna discusión sobre los minerales mas comunes recuperados normalmente. Se mencionan las consideraciones importantes para el diseño básico de una planta de concentración y se presentan cuatro esquemas de flujo sobre las operaciones más corrientes. Las plantas estudiadas en detalle incluyen: "Climax Molybdenum Co. By-Product Plant" y "Canada Tungsten Ltd. Plant". Las plantas brevernente reseñadas incluyen: "Palabora Mining Co. Uranium Recovery Facility" y "Bridge Hill Ridge Heavy Mineral Recovery Plant of Mineral Deposits Ltd."

Jan 1, 1982

By E. Suoninen, K. Laajalehto, L. Kartio

Efficient separation of pyrite from other sulfides is of great importance for the metallurgical performance of flotation processes. In this work Fourier Transform Infrared Spectroscopy (FTIR) and X-ray Photoelectron Spectroscopy (XPS) were used to study the surface chemistry of pyrite in depression, activation and xanthate adsorption under conditions of controlled potential. Modifications of pyrite surfaces after treatment with depressants (lime, sulfur dioxide, sodium cyanide) and after activation with metal ions (Cu, Pb) were studied. The principal adsorption product identified on pyrite was dixanthogen whose formation started at about +0.15 V and +0.25 V (vs, SHE) in ethyl and amyl xanthate solutions, respectively. Copper xanthate was formed on copper(II) activated pyrite. Activation mechanism of pyrite by copper(II) salts is likely to be electrochemical where copper occurs as copper(I) on the surface of pyrite. Effective depression is achieved by sulfur dioxide and sodium cyanide. Depression at high pH is due to formation of iron(III) hydroxides. Calcium ions do not affect the electrochemistry but adsorb on pyrite and reduce the surface sites for dixanthogen adsorption.

Jan 1, 1995

By Harry R. Price, Jerome C. Neyer

INTRODUCTION Safety must be a primary consideration in the design and construction of tunnels. Tunnel construction has historically been considered a high-risk business. During the construction of the 14.8 kilometer (9.25) mile St. Gotthard Tunnel in the Swiss Alps in the 1870s, 310 lives were lost and another 877 workers permanently disabled. In more recent days, two tunnel construction accidents in 1971, one in Michigan and one in California, claimed the lives of 38 workers. Prior to 1971, most regulations governing safety in tunnel construction were developed by the U.S. Bureau of Mines. These included a 1941 Bulletin 439, "Some Essential Safety Factors for Tunneling" and a 1968 Bulletin 644 which updated Bulletin 439. In 1970, the United States passed the Occupational Health and Safety Act (OSHA) which became effective in early 1971. That act covered all sorts of workplace activities including Tunnels and Shafts in 29 CFR 1926.800. In 1989, a revised and renamed 29 CFR 1926.800 was issued for Underground Construction. Some of the changes introduced in this rule were the outgrowth of improvements made in the California and Michigan codes after the 1971 accidents. These new regulations are the "Rules to Live By" for tunnel construction in the United States and are generally accepted as appropriate for tunnel construction throughout the world.

Jan 1, 1995

By S. B. Patton, T. Novak, R. L. Sanford

A comprehensive approach to the development and organization of an expert system designed to assist electricians in diagnosing electrical faults in mining machinery is discussed. The system includes diagnostic, reference, and tutorial programs. The diagnostic portion of the system is based on a causal-reasoning approach, which is used to establish a hierarchy of symptoms and the subsequent production rules for identifying component-level failures in the motor-control circuit of a shuttle car. With this approach, conclusions are developed directly from knowledge of the circuit and its behavior (in both working and failure modes) based on first principles, rather than the heuristics of a domain expert. The symptoms and their hierarchal structure are formulated by creating "what if' scenarios and performing a qualitative circuit analysis for each fault. Techniques for incorporating interactive graphical displays of the circuit schematic into the diagnostic portion of the system are also presented. Supportive computer programs that provide reference material and tutorials on the circuit are also described.

Jan 1, 1990

By D. Koch

Bentonites and bentonite containing sealing materials are used since many years for sealing purposes in foundation, dike construction, hydraulic engineering and landfill construction, especially for encapsulation of old waste deposits In the near future compacted bentonites will be important components of multi-barrier systems for dry charge of old mines, for underground disposal of hazardous or radioactive wastes. Because of their exceptional physical, structural and chemical properties, bentonites are offering manifold possibilities to protect the environment against the negative effects of dumping grounds. Often the compliance with legal regulations for waste dumping or the isolation of contaminated areas is possible only by using bentonite containing sealing systems. The essential properties of bentonite, bentonite containing building materials and the different techniques of making horizontal technical base liners and vertical cut-off walls are explained. For horizontal technical base liners the adsorption ability, the ion exchange capacity and the swelling behavior of bentonites are important. For cut-off walls bentonite controls the rheological behavior of the slurry and is responsible for the low permeability of the hardened bentonite-cement-wall. In the multi-barrier systems of repositories for chemical or radioactive wastes compacted bentonites are considered to be favourable sealing and backfilling materials because of their high swelling capacity, their adsorption and ion-exchange ability and their plasticity in water saturated state.

Jan 1, 2005

By R. A. Bauer

Investigations of bedrock within subsided areas over abandoned coal mines in Illinois reveal very little disturbance of the bedrock. In areas that have surface subsidence of 0.3 to 1 m (1 to 3.25 ft), examination of cores from exploration drilling and investigations of the boreholes by means of closed circuit television have shown that fractures are spaced at least 0.9 to 3.6 m (3 to 12 ft) apart. They are located within a zone 6 to 15 m (20 to 50 ft) above the collapsed area in coal mines 42.6 to 112.7 m (140 to 370 ft) deep. The dip of the fractures ranges from 25° to 60°, cutting across nearly horizontal sedimentary bedding planes. The amount of fracturing found in the collapsed area decreased as the amount of soft, weak materials increased in the immediate overburden of the mine.

Jan 1, 1987