Search Documents

By K. Huttu, A. van Wageningen

"The Kittilä underground mine in northern Finland is extracting one of the largest known gold deposits in Europe. Kittilä achieved commercial production on May 1, 2009, becoming Agnico Eagle’s first mine to open outside of Canada. The Kittilä orebodies were initially mined from two openpits – Suuri and Roura – and underground operations were added in October 2010. The pits were mined out in November 2012, so mining is now entirely underground in the Suuri and Roura deposits. Additional, small openpits will mine any remaining near-surface reserves in the future.The Kittilä Mine is located in the Lapland region of northern Finland, approximately 900 km (560 miles) north of Helsinki and 150 km (93 miles) north of the Arctic Circle. With a mine life estimated through 2034, Kittilä is Agnico’s longest-life mine.The mine’s proven and probable reserves contain 32 Mt (4.7 million oz) at 4.6 g/t (0.13 oz/ st) gold. Ore has been mined from underground since 2010. The original 3 kt/d (3,300 stpd) operation underwent an expansion project to increase the throughput capacity of the mill by 1 kt/d (1,100 stpd), starting by the end of 2014.The region around the Kittilä Mine is underlain by mafic volcanic and sedimentary rocks of the Kittilä Greenstone Belt oriented nearly vertical. This greenstone belt is similar to those hosting Agnico Eagle’s Canadian deposits in Quebec’s Abitibi region and Nunavut. At the contact point between ironrich and magnesium-rich rocks lies a 100- to 200- m (330- to 660-ft) thick structural zone known as the Suurikuusikko Trend. This trend hosts the Kittilä deposit, where multiple mineralized zones have been traced over a strike length of more than 25 km (15 miles).Most of Agnico Eagle’s work has focused on a 4.5-km (2-mile) segment of the Suurikuusikko Trend that hosts the five main zones of the known gold reserves and resources. From south to north they are: Ketola, Etela, Suuri, Roura and Rimpi.The ore at the Kittilä Mine is refractory, making gold extraction relatively difficult because the gold is generally locked inside the two main sulfide minerals – arsenopyrite and arsenic-rich pyrite. Only about 4 percent is very fine-grained “free gold” (not locked in sulfide grains) and easier to extract. Most of this free gold is found in the outer, oxidized or eroded sections of the ore."

Jan 1, 2015

By Leons Kovisars

Introduction Labor is the major cost element for most mining operations. Labor costs are continually increasing, both in nominal and constant terms. This is true in developed as well as less developed countries. There are two ways to control unit labor costs - labor costs per ton of ore mined. Replace labor with capital (increased mechanization) or improve productivity (reduce the labor force). Every miner is aware of specific inefficiencies at his or her particular operation. But the miner has no comparative measurement standards. So it is difficult to know whether these inefficiencies are major or minor. The miner may also be unaware of large-scale inefficiencies because ongoing labor practices may have caused management complacency. Met Research studied mining labor productivity. The firm collected pilot data by sending direct-mail questionnaires to 320 nonferrous mining operations around the world. The response rate was 27%, of which 78 operations provided full data on production and employment.

Jan 11, 1983

By R. Q. Honaker, D. P. Patil, A. Sirkeci

Due to increased production of fine coal during mining during this century and inefficient fine coal recovery technologies, a vast reserve of high quality coal currently exists in refuse ponds. A novel fine coal circuit consisting of a hindered-bed classifier, an enhanced gravity concentrator and a flotation column has been evaluated for the recovery of fine coal from refuse ponds. The treatment of a pond derived from Pittsburgh No. 8 seam coal resulted in the production of a premium fuel containing less than 5% ash and a calorific value of about 30,173kJ/kg with 60% mass yield. The results from the treatment of two refuse pond materials will be presented in this publication.

Jan 1, 2000

By J. Drelich

The flotation limit of fine particles has been re-examined based on the effect of bubble size on contact angle, and a new surface chemistry-limited relationship describing the minimum particle size which can be floated is proposed. In this analysis the critical value of bubble-solid contact radius (re) for which there is no effective attachment between particle and bubble has to be determined. The values of re determined by extrapolation of our experimental data for contact angle versus bubble-solid contact diameter permit the prediction of the flotation limit of methylated quartz particles, with fraction-al coverage of trimethylsilyl groups from 0.07 to 0.51. The limit of fine particle flotation as determined by this theoretical approach agrees well with experimental data reported in the literature.

Jan 1, 1994

By R. E. Ray

In an effort to reduce the risks to underground miners of health hazards associated with exposure to high concentrations of diesel particulate matter(dpm), the Mine Safety and Health Administration(MSHA) published proposed rules in 1998 limiting dpm exposure in both underground coal and metal and nonmetal mines. The proposed rule for underground coal mines would require removal of 95% of dpm by mass, while the rule for metal and nonmetal mines would eventually limit total carbon exposure from dpm to 160 micrograms per cubic meter of air over an eight-hour shift. The comment period for both proposed standards ended on July 26, 1999.In this session, representatives from MSHA, the National Institute for Occupational Safety and Health (NIOSH), equipment manufacturers, labor and industry will discuss the impact of the proposed regulations on mine operations and worker health. Questions will be taken from the audience after brief presentations from each panelist. This paper provides a compilation of written summaries of each panelist’s opening presentation.

Jan 1, 2000

By Haydn H. Murray

Kaolin is defined and described as an industrial mineral. In addition the types of deposits -primary and secondary are defined and the genesis of kaolin from feldspars and other minerals discussed. The major deposits of the world found in the United States, Great Britain, Brazil, and Czechoslovakia are described along with many of the minor kaolin deposits. Four areas which have very large deposits of kaolin could, with technological breakthroughs to reduce viscosity significantly, become important factors in supplying the world markets which are increasing year by year.

Jan 1, 1977

By David Young

This paper presents tunnel design considerations for the SR75/282 Transportation Corridor Project in Coronado, California. The project is managed by the City of Coronado in cooperation with Caltrans and the US Navy and may include a one-mile long twin-tunnel section with two options: a 36.5 foot diameter twin-bored tunnel or a twin cut-and-cover box. The alignment crosses the Coronado Fault, and design provisions were needed at the fault crossing to maintain life safety and prevent rapid inundation of the tunnel in the event of fault rupture. These provisions are discussed along with considerations related to liquefaction and ground shaking. The project is currently in the planning stage with construction to start around 2012.

Jan 1, 2008

By L. A. Baker

The presence of goethite in a hematite ore has been shown to strongly affect the time of heating to the firing temperature. The investigation of spalling of single pellets and of packed beds has enabled free water and goethite spalling to be identified as separate phenomena. In addition, it has been shown that even for an 18 inch deep bed of green balls the free water and goethite drying periods can be considered separately. Based on this observation, a method of predicting production rate and hood temperature profile is presented. The method required knowledge of the ore goethite content, ore grind and the green pellet bulk density. Laboratory results were found to be in good agreement with actual plant practice and have led to improved process performance.

Jan 1, 1972

By Tim Q. Haldane

The ability to efficiently process lowgrade ores has allowed the Gold Fields Mesquite Mine in Imperial County, CA to expand from a 2.1 Mt/a (2.3 million stpy) rate in 1986 to its present 7.3 Mt/ a (8 million stpy) processing rate. Increased tonnage demands led to the 1989 construction and startup of a dump leach pad to supplement the existing heap leach operation. This resulted in an excellent opportunity to compare the two processes at the same operation. Additional operating costs associated with the crushed ore heaps are justified through enhanced recoveries, even at very low ore grades. Gold Fields' Mesquite Mine is a gold heap leach facility located about 55 km (35 miles) east of Brawley in southeastern California. Five open-pit mines will be developed over the projected life of the property, covering a total area extending to a maximum of 5.5 km (3.4 miles) to the east and west, and 2.4 kin (1.5 miles) to the north and south. Mesquite will process 7.3 Mt (8 million st) of ore and produce more than 6.2 t (200 000 oz) of gold in 1990.

Jan 1, 1990

By F. Alsobrook

Coleman Quartz Inc. has a long history as the sole U.S. producer of lascas for the cultured quartz growing industry based on its unique deposits in Arkansas. Since 1989 the company has also been producing metallurgical grade silica for the ferrosilicon industry from a deposit of unusually pure Arkansas novaculite. This paper chronicles Coleman's trans-formation of an abandoned railroad ballast quarry into a generator of $1.5 million in annual sales to a nontraditional novaculite market. Potential additional applications for this high quality silica rock will also be mentioned.

Jan 1, 1992

By Tim O’Neil

Tire companies have historically used the mining industry as a platform to launch new technologies. And the mining industry has been receptive to that. So, while developing its Two Piece Assembly, Goodyear noted a number of trends in the mining industry: •The global market sophistication of equipment and operations requires the packaging of products and services to provide the best return on investment. •Industry consolidation and growth have resulted in fewer, more powerful mining houses, leveraging purchasing power in the marketplace. •User productivity demands continue to drive original equipment manufacturers to develop higher pay-load equipment. •Technology needs include improved ergonomics, to reduce fatigue and increase operator productivity. •Increased laws and environmental regulation prohibit on-site whole tire disposal practices.

Jan 1, 2003

By Roozbeh Afzali

Designing an appropriate tunnel blasting pattern reduces the cost of rock breakage and subsequent operations such as loading, haulage and support of tunnels. For that reason, we developed a software that designs tunnel blasting patterns. Using this software, three different tunnel blast design models based on parallel hole cut, namely, Swedish, Konya and Energy Balance, were investigated and compared for a virtual tunnel. Accordingly, blasting patterns were designed, for different cross sections. The trend of parameters such as specific charge and specific drilling as functions of tunnel cross-section was determined for each model. Our results show that, in general, The Swedish model gives lower specific charge and specific drilling compared to other models.

Jan 1, 2008

By H. Sis, D. Dahlin, S. Chander, C. Summers

Bench-scale selective-flocculation tests were conducted on samples of Florida and Western phosphate process tailings. Physical, mineralogical, and surface characteristics were determined for both types of samples. The flocculation tests investigated dispersant and flocculant types and doses, pH, and slurry percent solids, while other parameters were held constant. Where selectivity was achieved, phosphate minerals remained dispersed, whereas silicate minerals flocculated and settled. In single-stage tests, flocculants having low to medium anionic character effectively upgraded products at moderately elevated pH. Multiple-stage tests, and tests in which flocculants of lower molecular weight were used as site-blockers, gave improved results.

Jan 1, 2002

By M. K. Mohanty

A modified coal flotation characterization procedure, referred to as the Advanced Flotation Washability (AFW) technique, has been developed which, compared to traditional procedures, provides a more accurate prediction of the optimum separation performance achievable by a froth flotation process. The AFW procedure uses a vertically-baffled flotation column which provides enhanced selectivity among particles of varying degrees of hydrophobicity due to a plug-flow environment and an improved carrying-capacity environment. In fact, the separation performance of the traditional procedures was enhanced by increasing the possibility of operating under improved selectivity conditions. The separation performance provided by the AFW procedure was superior to that obtained from multiple cleaning stages using commercially-available flotation columns under both kinetic and carrying-capacity limiting conditions.

Jan 1, 1997

By Walter Kahn

Increasing consideration is being given to simplifying traditional methods of tracing pipelines and maintaining required temperatures of stored fluids. Because of their reduction in capital costs, virtual elimination of maintenance. ease of control and "cleanliness"; interest in electrical techniques has accelerated. 1,2 Resistance cable and other heaters have been given some attention. but less well known in the recent introduction of thermal conductive coatings. This paper is addressed to the use of thermal conductive coatings for heating fluid-transport piping and storage tanks. Emphasis will be given to the simplicity, efficiency, and versatility of design and application which their unique properties further contribute to the general economics of electrical heating.

Jan 1, 1965

By Steve Kral

The Prospectors and Developers Association of Canada (PDAC) was established in 1932 in response to proposed regulations that would have threatened prospectors in Ontario. From there, the association grew to represent the interests of Canada?s mineral exploration and development industry. The PDAC?s mission statement reads: ?The PDAC exists to protect and promote the interests of the Canadian mineral exploration sector and to ensure a robust mining industry in Canada. The PDAC will encourage the highest standards of technical, environment, safety and social practices in Canada and internationally. ?Today, the PDAC?s 6,000 individual members include prospectors, developers, geoscientists, consultants, mining executives and students. In addition, the association?s membership includes 950 corporate members, representing senior, mid-sized and junior mining companies in addition to organizations that provide services and equipment to the mining industry. In 2010, the PDAC adopted its e3 Plus principles, a framework to guide its membership in responsible exploration.

Jan 1, 2011

By Yifan Ding, Shemek Oginski, Patrick Finn

The Manhattan section of the New York Water Tunnel No. 3 constructed by the Schiavone/Shea/Frontier-Kemper Joint Venture is a $668 million project. The contract includes a tunnel drive of 8.85 km (29,045 feet), tunnel lining of 14.77 km (48,468 feet)and construction of nine shafts ranging in depth from 143 m (469 feet) to 169 m(555 feet). Construction methods for excavation of the shafts are presented including raise bore, ground freezing, soil excavation, blasting, slashing, muck handling, rock support and shaft final concrete lining.

Jan 1, 2007

In 1992, the United States economy grew at a rate of 2%. The Gross Domestic Product rose to $5,946 billion. With 257 million people - 635,000 in mining including petroleum - the United States has more than 100 million dwelling units and more than 190 million licensed motor vehicles. New private housing starts rose I 1 % to 1.2 million units. New car production rose 4% to 5.7 million units. Truck and bus production rose 20% to 4 million units. The rate of inflation was 3.5% and the prime rate of interest was 6.25%. The Producer Price Index (1982 =100) was relatively unchanged from 1991 as follows: fuels and related products and power 80, metals and metal products 119, chemicals and allied products 126 and nonmetallic mineral products 117. Energy Imports of crude and refined petroleum, costing $50 billion, rose 3% to 455 Mm3 (2.9 billion bbl). Domestic petroleum production fell 1 % to 582 Mm3 (3.5 billion bbl). Petroleum supplied about 41 % of US energy, natural gas 24% and coal 23%. Coal production, 60% from surface operations, rose 1 % to 914 Mt (1 billion st). About 78% was used to generate electricity and 3% was coked. Exports valued at $4 billion included 57 Mt (63 million st) of metallurgical coal and 39 Mt (43 million st) of steam coal. Ura¬nium mining, including recovery from phosphates, fell 18% to 3 kt (3300 st) U308.

Jan 1, 1993

By R. S. Jurani

Sunshine Mining Co.'s Kellogg operation is the primary silver producer in the US. Maintaining a comfortable working environment in this deep underground mine historically has been a complex and costly problem. To improve the ventilation and cooling systems at a time of declining and un-certain silver markets, it was proposed to optimize the performance of existing facilities at minimum cost. This paper discusses a two-year, $400,000 optimization program that resulted in increased total mine airflow, cooler ambient temperatures, reduced compressed air usage, and lower energy consumption by primary fans, air compressors, and refrigeration plants. This saved the company about $650,000 per year.

Jan 1, 1988

By S. Rupprecht

"This article addresses the prevalence of poor public reporting practices of coal exploration results, coal resources and coal reserves in southern Africa. Currently, the reporting of coal tonnage without supporting coal qualities or saleable tonnes and quality is a poor reporting practice that occurs far too often. Not all coal is equal — therefore it is extremely important that investors or potential investors are provided with the full details of both run-of-mine (ROM) and saleable coal tonnage, their associated qualities and other material and relevant information.Competent or qualified persons should note that publicly reported information should be sufficient to enable an informed reader to make a reasonable and balanced assessment of the significance of the information provided. “Companies are encouraged to provide information in their public reports, which is as comprehensive as possible (CRIRSCO, 2013).” However, too often this isn’t the case, and material matters are either not reported or inadequately disclosed.According to the South African National Standard (SANS) 10320:2014 draft document, “tonnage and coal quality that will be available for sale, either in the raw ROM state (raw saleable) at a specified moisture content, or after beneficiation of the ROM coal by processing operations to produce materials at specified qualities, size ranges and moisture contents. The assessments must demonstrate that at the time of reporting, the marketing of the products is reasonably justified. The basis of the predicted practical product yield to achieve the saleable coal reserve must be stated. The moisture basis of reporting shall be stated.” An example as to why coal qualities are so important to the public, the requirements of South Africa’s electric public utility (Eskom) power stations are detailed in the followint paragraphs. The Kendal power station, commissioned in 1988, operates at a calorific value (CV) range of 19 to 20 MJ/ kg, an ash content between 29 and 34 percent and volatiles between 20 to 21 percent. Other power stations, such as Kriel or Hendrina, may require different qualities, such as a CV range of 22 to 23 MJ/kg, an ash content between 20 and 28 percent and volatiles between 22 to 23 percent. Thus, in terms of domestic saleable coal, it is not just about reporting the coal qualities but also informing the investor as to which power station the coal is intended to be sold as “boilers are designed to burn particular qualities of coal” and “it is not always possible to transfer coal between stations because of different quality requirements at each station (Chetty, 2010).” Sulfur content is another important quality with the ideal coal content having a quality of less than 1 percent sulfur."

Jul 1, 2019