Search Documents

By Li Jiuping, Zhong Gang, Chen Yong Zhang, I. Michael Gowring

The Liaoning Dahuofang Reservoir Water Transfer Project is an important development for the Department of Water Resources of Liaoning Province in northeastern China. The 85.3 km water conduit will transport water from the Hun River downstream of the Huanren Reservoir to the outlet on the Suzi River leading to the Dahuofang Reservoir. The additional water is required to sustain the growing cities of Fushun, Shen-yang, Liaoyang, Anshan, Panjin and Yingkou. The project is divided into seven contracts. Three TBM contracts comprise almost 75% of the work and the others are drill and shoot. The focus of this paper is about the creditable TBM performances achieved and some of the problems encountered by Chinese contractors; notably two having had no previous TBM experience.

Jan 1, 2007

By G. Roberts, S. S. Klima, W. R. Reed, J. Deluzio, G. Ross, A. Mazzella

The abstract discusses the problem of silicosis among roof bolter operators in coal mines due to respirable quartz dust (RCS) exposure. It presents a study comparing a new wet box collection system to the traditional dry box system. The wet box system uses water to saturate collected material, reducing RCS exposure during cleaning. The study found that the wet box system significantly reduced RCS exposures and quartz content in samples compared to the dry box system.

May 11, 2022

By Douglas R. Cook

Exploration record In preparing this paper, a list of world class discoveries prepared in 1983 has been updated. In both surveys, the following criteria were used in the definition of world class discoveries: • deposits that are continuously operated and consistently return a profit even in periods of low metal prices; • deposits large enough to significantly affect a medium sized corporation's profits; and • these deposits should be in the lower one-third cost per unit of metal produced for all similar deposits. Only 70 discoveries in the last 40 years qualified as world class deposits using these criteria. Unfortunately, this restricted population was too low to develop meaningful trends. The numbers were therefore enlarged to include all significant discoveries. The principal feature of a significant discovery is that its size and grade would yield more than $500 million in revenue using average metal prices for the last five years. A significant deposit should also meet some of the standards for a world class deposit. A tabulation of these deposits are shown in Table 1. The number of discoveries increased to 166 from 70 using the revised classification. The relationship between the number of discoveries per year and their location by continents was prepared from these data. Figure 1 shows the number of discoveries per year for the nonCommunist world. It also shows estimated and actual nonCommunist world exploration expenditures per year and the commodity price index. These data show that modern exploration started in the late 1940s, with the tempo picking up rapidly in the 1950s. The maximum discovery rate occurred in 1962. Thereafter, the discovery rate gradually declined to the present. This occurred despite a real increase in expenditures from about $200 million/a in 1955 (1982 constant dollars) to more than $900 million/a in 1980. Thus, these data suggest a significant decrease in the exploration success ratio (total exploration expenditures a year divided by the number of significant discoveries) in the last 20 years. As an example, $70 million was spent for each significant discovery in the early 1960s as compared with $225 million in the late 1970s (expressed in 1982 constant dollars). However, with the general declining trend of discoveries, one can perceive a more pronounced drop in 1973 and then a sudden increase in 1974, 1975, and 1976. This increase is probably related to the inflation of the 1970s that in turn created an environment for the explosion of commodity prices, as shown by the commodity price index on Fig. 1. Thereafter, the decline in discoveries resumed in 1975 until the present. Exploration performance by regions North American discoveries are shown in Fig. 2. The graph shows three pronounced high discovery peaks in 1962, 1975, and 1980-81.

Jan 2, 1986

By Brian Heer, David Young, Randall Essex

The Manapouri Power Station is New Zealand’s largest hydroelectric facility located on the South Island of New Zealand. Constructed in the 1960’s, it includes a 700 MW under-ground power station and a 9.8 km (6.1 mile), 9.2 m (30 ft) diameter tailrace tunnel. The output of the power station is currently limited due to excessive head losses in the tailrace tunnel. To remedy this situation, the Electricity Corporation of New Zealand (ECNZ) retained Woodward-Clyde to design a second tailrace tunnel and appurtenant facilities and prepare Contract Documents for construction. The Project will involve the construction of a 9.8 km(6.1 miles), 10 m (33 ft) diameter, TBM-mined tunnel, hydraulic control structures at the upstream and downstream ends of the tunnel, an underground dewatering shaft and station, and tailrace channel improvements. This paper summarizes the key design and construction issues addressed during the planning and design phases, outlines the risk management provisions incorporated in the Contract, and overviews the Interactive Tender Process (ITP)that was implemented during the pre-tendering and tendering periods.

Jan 1, 1997

By K. Zeidler, T. Schwind

The Fort Canning Tunnel, Singapore, is an approximately 50 feet (15m) wide vehicular tunnel under shallow ground cover that has been constructed according to the principles of the NATM. Its shallow location in soft ground combined with a high groundwater elevation in close vicinity of historically important features called for special design considerations combined with a rigorous monitoring scheme. Surface, sub-surface and in-tunnel instrumentation was installed to monitor the performance of the ground and tunnel support during construction. Comparison of actual reading data with the results from the computer modeling carried out during the design phase is provided in this paper.

Jan 1, 2007

By S. Bargigli, S. Ulgiati, M. Raugei, F. Cherubini

Metallic magnesium is mostly used in lightweight alloys in order to decrease fuel consumption in automotive applications. Several different production processes are currently used worldwide, and the magnesium production scenario is changing rapidly, with Chinese production increasingly dominating the world market. For the purpose of this paper, a novel approach to Life Cycle Assessment was applied, in which Material Flow Accounting and energy-based methods (Embodied Energy, Exergy and Emergy Analyses) are integrated and complemented, with a detailed description of the environmental hazards associated with emissions from all the different processes.

Jan 1, 2005

By Lawrence Pelham

Introduction Fluorspar demand or consumption has been taken for granted in recent years, except for those that produce, market, or consume the commodity. Thinking used to be that as the steel and aluminum industry goes, so goes fluorspar. This is much less true today. The industry is becoming more dependent on chemical industries that feed primarily off hydrofluoric acid (HF) production. The US Bureau of Mines (USBM) published an assessment of world fluorspar reserves and resources. It created a foundation of valuable data that can be used to monitor fluorspar availability. Celebrations were held this year commemorating the 100th anniversary of the isolation of fluorine. The US and other countries continue to struggle with the controversy of ozone depletion and the effect of fluorocarbons on the atmosphere. Goals for the government's strategic stockpile are being reevaluated. The market for fluorine chemicals is changing and diversifying, making it a challenge to assess and forecast fluorspar/fluorine demand. US production and distribution Fluorspar Fluorspar shipments from US mines reached an all-time high near the end of World War II in 1944 at 375 kt (413,800 st). Eighty-two mines produced more than 453 t (500 st) each, and 10 mines produced more than 9 kt (10,000 st.) each. Illinois supplied 43% of total shipments. Consumption in 1944 was 372 kt (410,200 st), of which 56% was used by steel producers and 32% by HF producers. This was the last year that US production exceeded US consumption. The post-World War II record for fluorspar shipments occurred in 1951 at 315 kt (347,000 st) 58 mines produced more than 453 t (500 st) and eight mines produced more than 9 kt (10,000 st).

Jan 11, 1986

By Steve Kral

Amax Coal Industries Inc.'s Delta Mine is a medium-sized. high-sulfur coal producer that has lived up to the challenges posed by nearly six decades of a highly competitive domestic coal market. The mine now faces one of its biggest challenges - the same one staring at the dozens of other high-sulfur producers in the Midwest - the Clean Air Act Amendments of 1990. The 59-year-old mine, located in the coal fields of southern Illinois, has remained one of the state's oldest continuously operating mines by rolling with the ups and downs of the coal market and by incorporating new technologies and innovative productivity improvements into its operation.

Jan 1, 1993

By VIVEK KASHYAP, EVODY TSHIJIK KARUMB, PATRICK TAYLOR

Zinc ferrite is considered an integral phase of zinc residues as their presence can render the processing of zinc and critical metals difficult. It is a refractory phase, formed at high temperature in the presence of zinc (Zn) and iron (Fe) during oxidative roasting in zinc processing plants. Because it is refractory to efficient leaching, unreacted zinc ferrite gets concentrated in the final zinc residue, making it a viable source of zinc and indium extraction. The refractory nature of zinc ferrite makes the extraction of associated critical metals difficult. In order to explore a potential economic and carbon-neutral zinc ferrite processing technique, our previous study proposed the partial reduction of zinc ferrite followed by sulfuric acid leaching of the roasting product [1-3]. As demonstrated in our previous studies, partial reduction of zinc ferrite results in a mixture of ZnO, Fe3O4 and FeO, which can be further subjected to leaching for efficient extraction of zinc and critical metals such as gallium and indium.

Dec 1, 2022

By R. A. Burns

The production of kaolin and calcium carbonate in North America exceeds 13 million tons sold into higher value market segments. With a few exceptions, the markets supplied exhibit mature growth rates. In some market sectors, technology changes have and continue to occur shifting pigment-type consumption and growth. New sources of supply will impact current businesses. New product and process developments for kaolin and calcium carbonates are continuing. Each of these issues is examined in developing a view of the future for kaolin and calcium carbonate in North America.

Jan 1, 1997

By John R. Sturgul, Elizabeth Yost

The number of Native Americans presently working as mining engineers is extremely low-perhaps three in the entire US. At the New Mexico Institute of Mining and Technology, it was felt that introducing high ability students to mining engineering at the high school level would encourage more to consider mining engineering as a career. New Mexico Tech, in Socorro, NM, has initiated a continuing summer college program for Native American high school students. The program, which began in the summer of 1980, is designed to introduce participants to college life, enrich their high school curricula, and expose them to the problems and challenges of a career in mining and related engineering fields. Students From reservations throughout New Mexico with a demonstrated aptitude for science and mathematics were encouraged to apply for admission. Preference was given to high school sophomores and juniors since it is hoped that students will want to return for a second year before graduating from high school and beginning university studies. The program seeks to impress upon the students the need fir Native Americans in the fields of seience and mineral engineering.

Jan 7, 1981

By Mohamed Yusuff

Modern transportation systems are one of the most important achievements of our civilization and provide us with tools for broadening individual and social freedom of choice. The transportation system initiated today is handed dawn to the next generation, probably with little choice because of the enormous expenditure of monies involved, and influence their way of life as to where they should live and where they should work. The ever increasing antagonism between the citizens and the planners of the transportation systems necessitates a careful review of the entire planning process. The planning process can be broadly classified into: the goal formulation and decision making process; the plan development process; and the plan implementation process. THE GOAL FORMULATION AND DECISION MAKING PROCESS Goal formulation and decision making is one of the vital phases of the planning process and is primarily based upon social values. In measuring social values, the planner must employ an appropriate scale of measurement since in the absence of this yardstick, these values tend to became vague and abstract ideals. The need for major social programs and concerns (poverty, etc.) of the urban areas should be analyzed to determine the type of transportation system which would contribute to the solution.

Jan 1, 1974

By R. J. Snoby, J. K. Alderman

Although once fairly common as a method of coal preparation in the United States, dry cleaning has virtually disappeared. Low-rank coals used for power generation in the western U.S. are suited for dry cleaning because water has limited availability in the American west. Surface moisture added through wet cleaning offsets energy improvement achieved from mineral matter reduction. Information will be presented on the commercial application of dry cleaning in North America, the historic development and current status of the technology, and the introduction of modern processing theory and control technology to the design of dry cleaning equipment and plants.

Jan 1, 2001

By Robert Labbe

The final tunnel lining for this project involved pumping vast quantities of concrete over large distances under the extremely busy streets of lower Manhattan. Approximately 68,000 cubic meters (89,000 cubic yards) were pumped from various locations over 152 meters (500 feet) below ground (Figure 1) to create nearly 14.5 kilometers (9 miles) of 3.05 meter (10 foot) diameter tunnel. Total distances pumped exceeded 1,645 meters (5,400 feet) horizontally after a vertical difference of over 152 meters (500 feet). The urban setting of the operation, coupled with the long distances over which concrete was pumped, created many problems which had to be dealt with along the way. A three-shift labor operation was implemented to allow sequential pouring of tunnel sections nearly every day. The fine tuning of the mix design was critical to make this operation successful.

By G. Chi, M. C. Fuerstenau, R. C. Bradt, A. Ghosh

Technical Papers, Mining Engineering Vol. 49, No. 12, pp. 70-75, Discussion by McIvor, R. and Fink, R. P. We must challenge what we consider to be dubious statements in the above-mentioned article. Much of what is reported was published elsewhere over a year ago (i.e., in their reference: Chi, G., Fuerstenau, M.C., Brandt, R.C. and Ghosh, A., 1996, "Improved comminution efficiency through controlled blasting during mining," International Journal of Min¬eral Processing, Vol. 47, p. 93). There is nothing unusual or significant about a 10% or more difference in grindability between two materials of apparently similar origin and other attributes (such as chemical assays, hardness and specific gravity). Consider also that: • the materials came from different locations in the pit; • only two sets of four blastholes were considered per blast: • spatial orientation with respect to the face and other blastholes was also altered; • only two pairs of data were collected; • the impact of sampling error and bias, • both of which could be significant in this case; and • normal experimental error in parameter measurement and calculation. It is clearly inappropriate to draw any conclusions with regard to cause-and-effect relationships without first presenting a thorough error analysis. A substantial number of randomly selected test and control areas might provide meaningful statistical evidence of the claimed effect of the variables being studied. Even that appears doubtful, however, because Figures 3 and 4 show about as much variation in crushing energy for the two "regular" conditions vs. regular and altered conditions. On a separate, but also important issue, broad experience with autogenous/semiautogenous milling has shown that smaller or weaker feed material results in reduced tonnage. ? Reply Thank you for the opportunity to respond to the comments of Messrs. Mclvor ant Fink. The points raised are addressed in the order of presentation. As the commenters noted, there are parallels between this article and a previous manuscript. The reason for these complementary articles is that the audiences for the two publications are different, although there is obviously some overlap. We believe that the different audiences each profit from the technical aspects of the two manuscripts. We are not in agreement that a grindability difference of 10% is insignificant. The laboratory work is corroborated by data obtained at plant scale, which confirms that an increase in throughput of the same magnitude (between 5% and 10%) is achieved when the blasting pattern is modified, i.e., reduced from 9 to 8 m (29.5 to 26.2 ft). This increase in throughput translates into substantial power savings for ore grinding. No differences in appearance in the rock were noted between the two adjacent areas. Rock in both areas belonged to the same rock mass/block, which was quite homogeneous and without geological features in between that could create drastic differences in comminution characteristics. Given the resources, we would have sampled from all of the holes. Additional data would certainly have been desirable, as would have been additional funding to expand the study. Their comment, "spatial orientation with respect to the face and other blastholes was also altered," is not clear. Figure 1 does not show the initiation sequence. Without the initiation sequence, we do not understand how the commenters concluded that spatial orientation with respect to the face and other blastholes was altered. The commenters may be trying to make the point that the four-hole configurations with respect to the original bench face are not exactly the same. In fragmenting the

Jan 1, 1999

By W. D. Eddy

Topaz is a fluorine-bearing aluminosilicate mineral of the kyanite-sillimanite group. The formula has been given as Al2SiO4(F,OH)2, [Al(F, OH)]2SiO4, or 2Al2O3?2Al(F, OH)3SiO2. Topaz is generally considered a semiprecious-to-precious gem mineral, but it is a fairly common minor constituent of granites. In 1937 the U.s. Geological Survey reported an occurrence of massive topaz in the 3 Brewer gold mine, Chesterfield County, S.C. Over the next 8 years considerable research was done on topaz to establish its properties and to determine possible end uses The first reported shipment of ore was in 1939 Peak production was reached in 194412, and output then began declining until the mine closed in 194913? During World War II topaz was used in refractories, as a flux in steel mills, and in the manufacture of borosilicate glass 14. The main advantage of using topaz over kyanite and sillimanite in refractory use was that calcined topaz converted to over 95 percent mullite (3A1203 .2Si02) while calcined kyanite or sillimanite contained only 88 percent mullite15. However, a major draw-back to utilization of topaz is the evolution of fluorides during calcination. In 1973 the Geological Survey reported that topaz occurred in probable commercial quantities in at least two domestic locationsl6: the Brewer area of South Carolina and a location in Colorado. The literature also indicated that progress had been made in controlling fluorine-bearing fumes. This research has progressed to the state where valuable fluorine compounds are being recovered on a commercial scale 17. Thus, a major obstacle to utilization of topaz appears to have been resolved. The Bureau of Mines under its program of advancing minerals technology initiated a project to study techniques for the concentration of topaz from disseminated materials. The objective of the study was to determine those techniques that would be used to produce topaz concentrates that could be utilized as a source of fluorine and mullite.

Jan 1, 1977

By R. J. Lytle

INTRODUCTION Prior to excavation in soil and rock, it is useful to know the subsurface structure. This is important information both for safety and for equipment scheduling reasons. It is useful to know whether parts of the subsurface might be potentially troublesome or of different character than is generally thought present. By using geophysical probing, it is possible to infer the location and size of these unusual regions. The ground structure is commonly estimated from core samples taken from boreholes. These cores give a detailed knowledge of the structure in the borehole. However, knowledge of the structure exterior to the borehole can only be extrapolated from core data. By using seismic and electromagnetic cross-borehole geophysical probing, remote probing can be used to sense the region exterior to boreholes. A recent advance has significantly improved the state-of-the-art for defining the ground structure between boreholes. This new procedure utilizes large amounts of data and provides a detailed picture of the subsurface. The data processing algorithms used are similar to those in medical imaging of the human body using x-rays, a science called x-ray tomography. This imaging of the ground is called geotomography, which is a shortened acronym for geophysical tomography. Several examples of geotomography applied to imaging ground structure are presented. Our approach has been to probe the ground with electromagnetic and seismic waves. We map the region of interest with signals transmitted between multiple source and receiver pairs lowered in boreholes on opposite sides of the region (Figure 1). The received signals vary according to the transmission properties of the media

Jan 1, 1979

By Faruk Oksuz, Cary Hirner, William A. Rochford

Grouting is a frequently utilized remedy in the planning and implementation of ground improvement and tunnel rehabilitation practice. The state-of-art grouting application used for Chicago’s McCook Reservoir project offers a unique alternative to the tunneling industry for pre-excavation grouting as well as tunnel rehabilitation, rescue and post-excavation ground improvements. The McCook Reservoir project included a computerized grouting control and data collection system for a precise and highly effective groundwater cutoff in fractured dolomites. By using balanced and stabilized grout mixes, the effective permeability of the rock mass was reduced over two orders of magnitude to less than 0.1 Lugeon by installing a double line grout curtain. The stable grout mix designs allowed high pressure and effective grouting at depths up to 125 m (410 ft).

Jan 1, 2005

By F. Wendling, R. C. Nascimento, S. S. Wendling

"The objective of this research is to study the quality of blast-furnace iron ore pellets with binary basicity 1 fired on a pilot scale using the two main firing processes that are presently in use in the world and comparing them. Currently, the great majority of pellet producers use the traveling grate process because of its higher production capacity. In this study, the physical and chemical qualities of the pellet feed, limestone, anthracite and bentonite were determined and the amount of additives for a blast furnace pellet with the defined basicity was calculated. The physical properties of the green and dried pellets were determined accordingly. Produced pellets, after being fired on a pilot scale using traveling grate and grate kiln, were subjected to chemical analysis and physical testing. No significant difference was observed in the metallurgical quality — that is, reducibility index (RI), reducing disintegration index (RDI) and swelling index (SWI) — of the pellets produced by both processes. However, a comparison of cold physical tests — tumble and cold compression strength — shows improved quality of the pellets fired using the grate kiln process.IntroductionThe development of human civilization owes much to iron and steel (Sun et al., 2015). Iron is the most used metal in the world, and it is the main component of steel, which is present in materials for structural engineering, automotive and general industrial applications (Liu et al., 2014). Increased global demand has led to a decrease in the resources of ore with high iron content (Zhang et al., 2015), and currently 95 percent of the iron ore in China needs processing before smelting as its iron (Fe) content is only about 30 percent on average (Liu et al., 2014).Pelletizing is a process to economically agglomerate iron ore pellet feed into pellet form. After balling, green pellets are conveyed to the final step of the manufacturing process (Pena, 1982). The process is a multifaceted one, involving high temperatures, air flow gas turbulence and complex equipment geometry (Larsson et al., 2009). The pellets are fed into blast furnaces, which are now predominantly used in the extraction of iron. Ore processing also requires physical separation, including crushing, grinding and water removal (Sun et al., 2015).The increase in steel consumption favors the exploitation of low-concentration ores and the production of pellets (Halt and Kawatra, 2014). Pellet quality is affected by various factors, such as their physical and chemical characteristics and their temperatures and residence times in the furnace (Halt, Silva and Kawatra, 2015). Different geological settings lead to a wide range of different minerals (Graça et al., 2015).This work aims to generate important information for the pellet industry in the area of physical and metallurgical qualities of the agglomerates obtained by two processes: traveling grate and grate kiln."

Jan 1, 2017

By M. Polat

A combined heavy medium-flotation process which incorporates the advantages of two widely employed cleaning methods, namely, heavy medium separation and flotation was used to achieve improved separation of coal from ash at fine sizes and to recover the heavy medium as a substantially recyclable product. The investigation was carried out in two successive phases. In the first phase, tests were performed to deter-mine the effect of different variables such as the medium density, flotation time, magnetite type, etc. on the efficiency of the process using in-plant samples from Homer City Coal Preparation Plant. In the second phase, the optimum conditions determined in the first phase were employed to determine the applicability of the process to a few Central Pennsylvania coals. It was observed that the process was very effective in recovering the magnetite. In most of the cases investigated, the magnetite was separated from the non-magnetic material at approximate-1 to 99 % recovery with a grade ranging from 95 to 99 %. The grade of magnetite decreased with increase in ash content of coal and with decrease in size of magnetite.

Jan 1, 1992