Search Documents

By L. R. Gremillion

Chemical and mineralogical data on 25 apatitic phosphate ores of diverse origins from commercial deposits around the world were widely variable. From 14 to 18 chemical constituents of each sample were determined, and each sample contained 4 to 10 mineral phases. Altogether there were 34 different mineral phases, many of which occurred in only one sample. The samples contained varieties of francolites, fluorapatites, and mixed hydroxyl-fluorapatites. The apatite compositions calculated from the chemical data showed that certain types of substitutions were characteristic of different apatite varieties, but every variety had some degree of substitution of (CO3)2 for (PO4)3 and the P2O5 contents of the apatites ranged from 35.1% for a North Carolina apatite to 41.9% for a Missouri apatite. In a concentrate with a grade of 32% P2O5, the North Carolina sample should contain about 8.7% gangue and the Missouri sample about 23.7% gangue. To optimize the digestion process of a phosphate are, it is necessary to consider the dissolution behavior of the different mineral phases during acidulation and the effects they may have on the chemical properties of a fertilizer intermediate. In the production of wet-process acids or superphosphates, the acidulation of certain minerals may cause foaming and formation of sludge, filtration, corrosion, and handling problems.

Jan 1, 1978

By B. Goertz

Since the turn of the century the mining industry in the United States has had a number of serious mine explosions, fires and ground fall disasters that have led to a major re-evaluation of mine communication and rescue practices. One of the hindrances of current underground communication technologies is the potential of lost or cut connections when a serious accident, such as an explosion, fire, inundation or major ground fall, takes place. The Mine Improvement and New Emergency Response Act of 2006 (MINER Act)1 mandated that each underground coal mine in the U.S. must provide for two-way wireless, post-accident communications between underground and surface personnel as well as electronic tracking of underground workers One area that has gained renewed attention in the mining sector is Through-The-Earth (TTE) communication. TTE technology has a major advantage in that transceiver devices can be carried by miners and set up quickly during an emergency, since they require no wire connection to the surface. TTE technology uses ultra-low frequency (1 to 4 kHz) electromagnetic waves, requiring relatively large wire loop antennas and highly sensitive receivers. The signal bandwidth is narrow and the permissible antenna currents in coal mines are restricted, which has led to limited usability of TTE technology in the past, as evidenced in research studies conducted by the U.S. Bureau of Mines in the 1970s. Yenchek (2012)2 pointed out that recent advances in receiver and signal processing technology have enabled voice and text communication capabilities and much improved sensitivity that offers new possibilities for TTE communication in mining applications. One company that has been developing such technology is Vital Alert Communication Inc. Vital Alert has been providing TTE communications since 2003 with a growing focus on emergency response and portable systems. The company?s Canary® Go System is one such product that looks to provide reliable communication capabilities in a portable, user friendly unit that can be utilized both for normal operation and mine rescue scenarios. Researchers at the Colorado School of Mines (CSM) have tested the Canary Go TTE communications system in the CSM Edgar Experimental Mine to determine signal propagation distances, signal quality and aspects of practical application.

Feb 23, 2014

By S. J. Schatzel, V. Gangrade

A ventilation research study was conducted by the National Institute for Occupational Safety and Health and a cooperating trona mine in the Green River basin of Wyoming, USA. The mine operation uses the longwall mining method in trona bed 17, a commonly mined unit in the region. The longwall face length is 228 m (750 ft), and caving on the face occurred up to the back of the longwall shields. The mine is ventilated using a main blowing fan and a bleeder shaft. For this study, sulfur hexafluoride (SF6) tracer gas was released in two separate monitoring experiments. For the first experiment, tracer gas was released on the face, this test focused on airflow along the longwall face of the active panel. Face test showed the airflow patterns to be more complex than just head-to-tail flow in the main ventilation air stream on the active panel. For the second experiment, tracer gas was released 2 crosscuts inby the face on the headgate side, this test focused on gas transport in the mined-out portion of the same active panel. Gob test showed a pathway of movement through the front of the active panel gob that moved outby from the tailgate corner. The primary pathway of tracer gas movement in the active panel gob was towards the headgate and tailgate bleeders and out of a bleeder shaft. The rate of movement towards the back of the gob was measured to be 0.19 m/s (37 fpm).

By G. D. Hood

The U.S. Bureau of Mines investigated rapid froth flotation through the use of more efficient bubble-particle collisions that improved the overall flotation kinetics. An in-line static mixer efficiently mixed the air bubbles, water, and ore, rapidly attaching the hydrophobic mineral to the bubble surface. As the mixture entered the flotation chamber, the hydrophobic mineral was already attached to the bubbles and was quickly floated away from the remaining ore pulp. A rougher concentrate containing 4.5 pct copper was obtained from a western porphyry copper ore containing 0.67 pct copper. Over 99 pct copper was recovered from the ore at a rate 7 times faster than conventional flotation.

Jan 1, 1991

By Terry B. Linde, William M. Dowall

The recently completed In-Pit Crushing and Conveying Project at Phelps Dodge's Morenci Mine is rated among the world's leading materials handling projects. The operation involves the crushing and transport of more than 109,000 tonnes per day of copper ore, utilizing regenerative conveyors capable of providing over 5.5 megawatts (7,000 hp) of equivalent electrical energy. This paper describes the key aspects of the project and includes: Original project objectives; System design criteria; System description; Optimization studies; Major design features; Equipment description; and System commissioning.

Jan 1, 1993

By P. R. Taylor

Batch leaching experiments have been performed to study the kinetics of galena leaching in fluosilicic acid solutions with oxidants. Variables studied included: fluosilicic acid concentration, oxidant type, oxidant concentration, particle size and leaching temperature. It was found that hydrogen peroxide was the most effective oxidant, compared to the others studied, and the effect of the oxidant concentration on the leaching behavior of galena was very significant. Also, decreasing the particle size and increasing the leaching temperature increased the extraction rate. The initial, apparent activation energy was calculated to be 11.72 kJ/mole (2.8 kcal/mole) and suggested that galena leaching in fluosilicic acid solution, with hydrogen peroxide as an oxidant, may be controlled by fluid film mass transfer initially. The reaction appears to be retarded by the formation of elemental sulfur and the sulfur oxidation becomes a major resistance to the overall leaching reaction.

Jan 1, 1992

By A. R. Negele

Kaolin-based pigments are the most widely used pigments in the paper industry. Several types are available and include standard hydrous, delaminated, calcined, chemically-structured, and most recently, composite pigments. Within each category, a spectrum of products is available to satisfy the application requirements of paper producers. The paper industry has a broad range of applications including fillers in woodfree and groundwood-containing papers, pigmented size press applications, ultra-lightweight and lightweight coated papers, coated merchant papers, cast coated papers and coated paperboard. Each application has its own set of performance criteria and suppliers must work with mills to identify appropriate product(s) to fulfill these requirements.

Jan 1, 1993

By N. D. Cristescu

The aim of the present paper is to show how a mathematical modeling of a creeping rock and that of an yieldable lining can allow us to obtain an optimization of the lining design and generally of the whole procedure and sequence of excavation-lining application. We follow the procedure presented by Cristescu (1989) Chap. 13, and Cristescu et al.(1987); for some other approaches see the literature mentioned, for instance, by Ladanyi and Gill (1988). We have in mind to describe the creep of the rock, i.e. the tendency of the tunnel to close in time, and to take into account that the lining itself may be deforming, i.e. possesses some rheological behavior. We start from the well known fact that "intelligent" lining, which are yielding to the pressure of the rock, may be much more successful in supporting creeping rocks than excessively strong, badly designed supports which are unable to resist to pressure of the rock, though these are oversized supports (too strong, too stiff, installed too early, etc.). In order to optimize the lining to be used for a certain rock, it is absolutely necessary to study in the laboratory the main mechanical properties of that specific rock and to formulate for it a reasonably simple mathematical model. Standard triaxial test results are quite enough to determine the model for the rock, combined with some creep tests which have to reveal the long-term behavior of rock (the so-called rheological model). What concerns the lining, we consider several kinds of linings existing today, for which a mathematical model was also formulated. One shows which is the interaction between the creeping rock? and the yielding lining and how can it be formulated in mathematical terms. Once written in mathematical terms, an optimization of the lining design and that of the excavation layout and support application sequence is possible. We will try to make the exposure as simple as possible, avoiding details and having in mind to give only a sketch of the problem, while the mathematical details could be worked out quite easy.

Jan 1, 1994

By Joseph M. Driscoll

After 30 years of successfully mining gold, Newmont Gold has temporarily ceased production from the original Carlin Pit. In late 1993, the Carlin East decline was driven and an extensive underground exploration program was started. Today, Newmont Gold produces refractory ore from the Carlin East Underground at the rate of 864 t/d (950 stpd). Annual production is more than 3.1 t (100,000 02). More than 70 underground miners will be employed during Carlin East's estimated six-year mine life. About 70% of the ore at Carlin East is mined by mechanized longhole stoping with delayed, cemented backfill. The remaining ore is mined by underhand drift and cemented fill methods.

Jan 1, 1997

By Sandro Moro, Giuseppe Tiberti, Giovanni Plizzari, Antonio Conforti

"During TBM operations, thrust jacks apply high-concentrated forces to the last installed precast segment. These loads generate a disturbed region in the precast segment under the thrust jacks, in which significant tensile stresses (defined as splitting or bursting stresses) occur perpendicular to the load direction. In addition, due to the demand of compatibility, the combined effect of TBM high-concentrated loads determines tensile spalling stresses in the area far from the loads. Therefore, local rebars or fiber reinforcement are required in these areas. This paper focuses on the study of the effects generated by high-concentrated loads exerted by TBM hydraulic jacks, mainly in terms of both spalling and splitting phenomena. Experimental tests on small-scale specimens showed that polypropylene fiber reinforcement significantly enhances both the bearing capacity and the ductility. Moreover, polypropylene fibers resulted in very effective control of compatibility cracks.INTRODUCTIONTunnel segments are generally reinforced by conventional rebars (RC segments) in order to resist the tensile stresses both at Serviceability (SLS) and Ultimate Limit States (ULS).In the two last decades, Fiber Reinforced Concrete (FRC) has been used in many precast tunnel segments (sometimes also in combination with conventional rebars). Steel Fiber Reinforced Concrete (SFRC) is generally used for these applications even though there is a growing industry interest on macro-synthetic fibers for structural applications. Conforti et al. (2015) showed that polypropylene (PP) macro fibers can be used as shear reinforcement in both wide shallow and deep beams. Referring to precast tunnel linings, very few early experiences are reported in literature. Bonalumi et al. (2015) developed full-scale tests on tunnel elements reinforced by PP fiber reinforcement and conventional rebars (hybrid solution). The design process of segmental concrete tunnel linings generally models the standard load cases of demolding, storage, transportation, positioning and embedded ground condition. In all these stages the ring can be modelled as simple curved beam elements (having a height equal to the lining thickness and a width equal to the segment length). During these loading conditions, flexural demand is generally limited; thus, in case of conventional RC elements, a rather low ratio of longitudinal curved rebars is usually adopted (?s of about 0.2-0.3%)."

Jan 1, 2016

By C. R. DeGennaro, M. R. Girman, J. Bickson, J. P. Homer, C. C. Jobes

Between 2005 and 2021, a NIOSH internal review showed that haul trucks were involved in 54 incidents at surface mines in the United States. Haul truck collision warning and avoidance systems (CXS) can assist in preventing accidents at surface mines. CXS use technologies to detect people or objects and alarm to alert haul truck operators. Robust testing can help ensure that they detect objects without excessive false positive alarms. Testing and validation would increase confidence in and encourage implementation of a CXS. Researchers from the National Institute for Occupational Safety and Health (NIOSH) reviewed documents related to the evaluation and validation of CXS with two objectives: (1) to identify methods and parameters used to evaluate detection performance and (2) to identify gaps in CXS test methods and in detection performance. Stakeholders can use the findings from this research to guide implementation of CXS to improve safety at surface mines.

Mar 2, 2022

By Mahaboob Basha Shaik, Shakuntala Tudu, Indrajit Paul, Chandra Sekhar, Neha Gupta, Amit Kumar, Srinivas Dwarapudi, Arvind Kumar Patel

In this study, the effect of colemanite and calcined colemanite (CC) addition on the properties of iron ore pellets is studied. The pellets are prepared in a lab without and with 0.2% colemanite and varying amounts of CC from 0 to 1.0 wt%in steps of 0.2%. A reference pellet is prepared under typical plant conditions, and the properties of the reference pellet are considered as the base value for improving the cold compressive strength (CCS) while maintaining the other parameters at an acceptable limit without altering the pellet. The study also aims to provide a detailed characterization of colemanite and calcined colemanite to better understand their behaviour during firing. The lab-scale results show that the CCS of pellets made with 0.2% colemanite was reduced by 222 points (60%) as compared to the reference pellets due to crack formation during firing. The results show an improvement in the CCS of the indurated pellets with CC dosage up to 0.4%, and decreasing strength is noted thereafter. It is observed that the swelling index increases with the increase in calcined colemanite dosage. To simulate plant conditions, reference pellets and pellets with optimized CC dosage were fired in a plant furnace.

Oct 16, 2020

The initiation of a panel cave is an extremely important and infrequent event in the life of a large underground caving operation. A new cave was initiated at the Henderson Mine in 1991, 15 years after its first cave had been developed in 1976. The original cave was started after a half billion dollars had been invested in the development of the mine, mill and 23 km haulage system. Many things had changed since 1976, the most significant of these being much lower realizations for molybdenum. In 1976 the high demand for molybdenum and uncertainty of caving characteristics, formed the basis for a very conservative cave initiation sequence with miles of boundary weakening and inspection drifting. In 1991 the highly competitive molybdenum market in conjunction with 15 years of caving experience made for a very different mining climate.

Jan 1, 1994

By B. Yarar

Samples of coal from an adit in the Fording River District of British Columbia showed hydrophilic properties between depths of 0-24.5 meters and was naturally hydrphobic at higher depths. Laboratory experiments indicated that weathered samples (i.e., those mined at 0-24.5m) could be upgraded by froth flotation at pH<2 following slimes removal. The i.e.p. of samples varied regularly between pH=1.6-4.1, the weathered fractions being at the lower end of the pH scale. These values followed a pattern comparable with the flotation behavior of samples. A patchwise structure for coal surfaces determining the resultant disjoining pressure, which in turn determines flotation-non flotation relationships is postulated.

Jan 1, 1982

By K. Schonert

Jigging is a separtion process that has already been described by Agricola in 1556. Fine size material is normally treated in a hutch jigging process, in which the heavy particles are penetrating the jigging bed and are recovered in the hutch. In this process, a ragging consisting of the same or higher specific gravity particles is inserted upon the screen. The ragging is used mainly as a valve to maintain a constant upward flow of the water. Since the heavy particles should pass easily into the hutch, the ragging particles are up to ten times larger than the maximum feed size (1). In the fine size range - 1 mm the performance of jigs is mainly insufficient; some of the low density particles percolate the ragging while the hutch water flow prevents the fine heavy particles from entering the bed (2). By giving a thin layer of particles, which posesses a density sensitivity in case of certain adjustment of flow conditions, directly on the screen, the precision of separation can be increased. Stroke length and frequency have to be adjusted to give this filter layer a homogenous porosity between 60 and 70% during the pulsion phase, and the "en masse" lifting of the bed, as it is known in jigging of coarser material, has to be prevented (3). In this case, the jig cycle is only of minor influence.

Jan 1, 1987

By H. H. Hayden

The accident repeater-40 you have one at your mine? Unless your company is vastly different from most coal companies, you will find that a small percentage (11-12%) of your employees will have a large percentage (47-50%) of your accidents. When you find out that this is a fact, what do you do? First, you establish a set of guidelines that can be used in identifying the ?accident repeater?. Next, you determine the type of action necessary to improve work habits and safety performance of the accident repeater. With these two steps in mind, objectives are developed for an ?accident repeater? program.

Jan 1, 1984

By K. Lang

The use of high-efficiency electrical submersible pumps (ESPs) for large scale, open pit mine dewatering operations provides a good example of how technology, products and services from the oil and gas industry can be adapted to the mining industry. In this case, the mine is Goldcorp?s Peñasquito in the Zacatecas state of Mexico, at the Peñasco and Chile Colorado open pit deposits. The technology, products and services are from Schlumberger artificial lift (AL) and Schlumberger industrial water services (IWS). Overview of high-efficiency ESPs This section provides a brief description of the basic components, specifications and operating capacity ranges for the ESPs compared with traditional or conventional dewatering well pumps. This information helps to establish how ESPs provide certain functional and economic advantages over conventional pumps in a mine dewatering application. A schematic of a high-efficiency ESP in an oil and gas (O&G) application is shown in Fig. 1.

Sep 1, 2013

By Donna Wallace

Past EPA groundwater monitoring programs required that contamination not leave the boundaries of a disposal facility. New regulations under the Resource Conservation and Recovery Act (RCRA) require that once hazardous waste constituents are detected beyond the limits of the disposal area, a program to define the rate and extent of contaminant migration must be instituted. Future regulations are likely to include even more stringent groundwater protection criteria. The implications of both the existing and probable future groundwater protection and monitoring requirements in terms of using geologic containment as a means of disposing of hazardous waste are explored in this paper.

Jan 1, 1981

he leaching behavior of palladium in ammoniacal solutions has been investigated by using the rotating disk technique in an autoclave. The study included the effect of rotating speed, temperature, oxygen pressure, composition of ammoniacal solutions, and catalyst on the overall leaching rate. The dissolution of palladium in ammoniacal solutions was discussed in view of the thermodynamics and a kinetic model. Even though the potential-pH diagram suggests that palladium metal can dissolve in ammoniacal solutions at room temperature, it was found that the dissolution was too slow at temperatures below 100°C but was significantly improved at higher temperatures. It was also found that the rotating speed of palladium disk had no effect on the leaching rate. The apparent activation energy was found to be 69.7 kJ/mole. Based on the results obtained, it is concluded that the dissolution of palladium is controlled by chemical reaction.

Jan 1, 1997

Large deposits of eudialyte, a low grade zirconium bearing mineral, occur on the Southern Coast of Greenland in the Ilimaussaq intrusion. Various processes were tested in the laboratory to recover eudialyte from these ores, including flotation, leaching, gravity and magnetic separation. A combination of dry and wet magnetic separations has the advantage of simplicity and the least environmental impact for the location. This paper summarizes the results of laboratory testwork to develop a two-stage treatment process to recover the eudialyte by magnetic separation.

Jan 1, 1993