Search Documents

By L. R. Gremillion

Chemical and mineralogical data on 25 apatitic phosphate ores of diverse origins from commercial deposits around the world were widely variable. From 14 to 18 chemical constituents of each sample were determined, and each sample contained 4 to 10 mineral phases. Altogether there were 34 different mineral phases, many of which occurred in only one sample. The samples contained varieties of francolites, fluorapatites, and mixed hydroxyl-fluorapatites. The apatite compositions calculated from the chemical data showed that certain types of substitutions were characteristic of different apatite varieties, but every variety had some degree of substitution of (CO3)2 for (PO4)3 and the P2O5 contents of the apatites ranged from 35.1% for a North Carolina apatite to 41.9% for a Missouri apatite. In a concentrate with a grade of 32% P2O5, the North Carolina sample should contain about 8.7% gangue and the Missouri sample about 23.7% gangue. To optimize the digestion process of a phosphate are, it is necessary to consider the dissolution behavior of the different mineral phases during acidulation and the effects they may have on the chemical properties of a fertilizer intermediate. In the production of wet-process acids or superphosphates, the acidulation of certain minerals may cause foaming and formation of sludge, filtration, corrosion, and handling problems.

Jan 1, 1978

By S. J. Schatzel, V. Gangrade

A ventilation research study was conducted by the National Institute for Occupational Safety and Health and a cooperating trona mine in the Green River basin of Wyoming, USA. The mine operation uses the longwall mining method in trona bed 17, a commonly mined unit in the region. The longwall face length is 228 m (750 ft), and caving on the face occurred up to the back of the longwall shields. The mine is ventilated using a main blowing fan and a bleeder shaft. For this study, sulfur hexafluoride (SF6) tracer gas was released in two separate monitoring experiments. For the first experiment, tracer gas was released on the face, this test focused on airflow along the longwall face of the active panel. Face test showed the airflow patterns to be more complex than just head-to-tail flow in the main ventilation air stream on the active panel. For the second experiment, tracer gas was released 2 crosscuts inby the face on the headgate side, this test focused on gas transport in the mined-out portion of the same active panel. Gob test showed a pathway of movement through the front of the active panel gob that moved outby from the tailgate corner. The primary pathway of tracer gas movement in the active panel gob was towards the headgate and tailgate bleeders and out of a bleeder shaft. The rate of movement towards the back of the gob was measured to be 0.19 m/s (37 fpm).

By Sandro Moro, Giuseppe Tiberti, Giovanni Plizzari, Antonio Conforti

"During TBM operations, thrust jacks apply high-concentrated forces to the last installed precast segment. These loads generate a disturbed region in the precast segment under the thrust jacks, in which significant tensile stresses (defined as splitting or bursting stresses) occur perpendicular to the load direction. In addition, due to the demand of compatibility, the combined effect of TBM high-concentrated loads determines tensile spalling stresses in the area far from the loads. Therefore, local rebars or fiber reinforcement are required in these areas. This paper focuses on the study of the effects generated by high-concentrated loads exerted by TBM hydraulic jacks, mainly in terms of both spalling and splitting phenomena. Experimental tests on small-scale specimens showed that polypropylene fiber reinforcement significantly enhances both the bearing capacity and the ductility. Moreover, polypropylene fibers resulted in very effective control of compatibility cracks.INTRODUCTIONTunnel segments are generally reinforced by conventional rebars (RC segments) in order to resist the tensile stresses both at Serviceability (SLS) and Ultimate Limit States (ULS).In the two last decades, Fiber Reinforced Concrete (FRC) has been used in many precast tunnel segments (sometimes also in combination with conventional rebars). Steel Fiber Reinforced Concrete (SFRC) is generally used for these applications even though there is a growing industry interest on macro-synthetic fibers for structural applications. Conforti et al. (2015) showed that polypropylene (PP) macro fibers can be used as shear reinforcement in both wide shallow and deep beams. Referring to precast tunnel linings, very few early experiences are reported in literature. Bonalumi et al. (2015) developed full-scale tests on tunnel elements reinforced by PP fiber reinforcement and conventional rebars (hybrid solution). The design process of segmental concrete tunnel linings generally models the standard load cases of demolding, storage, transportation, positioning and embedded ground condition. In all these stages the ring can be modelled as simple curved beam elements (having a height equal to the lining thickness and a width equal to the segment length). During these loading conditions, flexural demand is generally limited; thus, in case of conventional RC elements, a rather low ratio of longitudinal curved rebars is usually adopted (?s of about 0.2-0.3%)."

Jan 1, 2016

By Fengmei Chen, Na Liu, Bingrui Li

A quantitative analysis method based on the airflow influence factors is proposed to evaluate airflow stability and discriminate airflow directions in complex ventilation networks. The law governing the changes in airflow caused by changes in branch resistance is revealed based on simulations of the airflow state in a ventilation network and a statistical analysis of the results. Then, three evaluation indices (airflow sensitivity, airflow influence factor, and critical airflow) are determined, matrices of the airflow influence factors and critical airflows are constructed, and a quantitative evaluation method for ventilation system stability and an airflow directional discriminant are proposed. The results show that the stability of a ventilation system can be reliably evaluated based on the airflow influence factors. The sensitive branches and dominant branches in the ventilation network can be determined based on the matrix of airflow influence factors, and the reversed branches, the trigger branches, and the reversal conditions can be determined based on the critical airflow matrix and the matrix of airflow influence factors. The proposed airflow directional discriminant is suitable for evaluating arbitrarily complex networks.

Nov 15, 2023

By C. R. DeGennaro, M. R. Girman, J. Bickson, J. P. Homer, C. C. Jobes

Between 2005 and 2021, a NIOSH internal review showed that haul trucks were involved in 54 incidents at surface mines in the United States. Haul truck collision warning and avoidance systems (CXS) can assist in preventing accidents at surface mines. CXS use technologies to detect people or objects and alarm to alert haul truck operators. Robust testing can help ensure that they detect objects without excessive false positive alarms. Testing and validation would increase confidence in and encourage implementation of a CXS. Researchers from the National Institute for Occupational Safety and Health (NIOSH) reviewed documents related to the evaluation and validation of CXS with two objectives: (1) to identify methods and parameters used to evaluate detection performance and (2) to identify gaps in CXS test methods and in detection performance. Stakeholders can use the findings from this research to guide implementation of CXS to improve safety at surface mines.

Mar 2, 2022

The initiation of a panel cave is an extremely important and infrequent event in the life of a large underground caving operation. A new cave was initiated at the Henderson Mine in 1991, 15 years after its first cave had been developed in 1976. The original cave was started after a half billion dollars had been invested in the development of the mine, mill and 23 km haulage system. Many things had changed since 1976, the most significant of these being much lower realizations for molybdenum. In 1976 the high demand for molybdenum and uncertainty of caving characteristics, formed the basis for a very conservative cave initiation sequence with miles of boundary weakening and inspection drifting. In 1991 the highly competitive molybdenum market in conjunction with 15 years of caving experience made for a very different mining climate.

Jan 1, 1994

By B. Yarar

Samples of coal from an adit in the Fording River District of British Columbia showed hydrophilic properties between depths of 0-24.5 meters and was naturally hydrphobic at higher depths. Laboratory experiments indicated that weathered samples (i.e., those mined at 0-24.5m) could be upgraded by froth flotation at pH<2 following slimes removal. The i.e.p. of samples varied regularly between pH=1.6-4.1, the weathered fractions being at the lower end of the pH scale. These values followed a pattern comparable with the flotation behavior of samples. A patchwise structure for coal surfaces determining the resultant disjoining pressure, which in turn determines flotation-non flotation relationships is postulated.

Jan 1, 1982

By K. Schonert

Jigging is a separtion process that has already been described by Agricola in 1556. Fine size material is normally treated in a hutch jigging process, in which the heavy particles are penetrating the jigging bed and are recovered in the hutch. In this process, a ragging consisting of the same or higher specific gravity particles is inserted upon the screen. The ragging is used mainly as a valve to maintain a constant upward flow of the water. Since the heavy particles should pass easily into the hutch, the ragging particles are up to ten times larger than the maximum feed size (1). In the fine size range - 1 mm the performance of jigs is mainly insufficient; some of the low density particles percolate the ragging while the hutch water flow prevents the fine heavy particles from entering the bed (2). By giving a thin layer of particles, which posesses a density sensitivity in case of certain adjustment of flow conditions, directly on the screen, the precision of separation can be increased. Stroke length and frequency have to be adjusted to give this filter layer a homogenous porosity between 60 and 70% during the pulsion phase, and the "en masse" lifting of the bed, as it is known in jigging of coarser material, has to be prevented (3). In this case, the jig cycle is only of minor influence.

Jan 1, 1987

By H. H. Hayden

The accident repeater-40 you have one at your mine? Unless your company is vastly different from most coal companies, you will find that a small percentage (11-12%) of your employees will have a large percentage (47-50%) of your accidents. When you find out that this is a fact, what do you do? First, you establish a set of guidelines that can be used in identifying the ?accident repeater?. Next, you determine the type of action necessary to improve work habits and safety performance of the accident repeater. With these two steps in mind, objectives are developed for an ?accident repeater? program.

Jan 1, 1984

By Joseph M. Driscoll

After 30 years of successfully mining gold, Newmont Gold has temporarily ceased production from the original Carlin Pit. In late 1993, the Carlin East decline was driven and an extensive underground exploration program was started. Today, Newmont Gold produces refractory ore from the Carlin East Underground at the rate of 864 t/d (950 stpd). Annual production is more than 3.1 t (100,000 02). More than 70 underground miners will be employed during Carlin East&apos;s estimated six-year mine life. About 70% of the ore at Carlin East is mined by mechanized longhole stoping with delayed, cemented backfill. The remaining ore is mined by underhand drift and cemented fill methods.

Jan 1, 1997

By Donna Wallace

Past EPA groundwater monitoring programs required that contamination not leave the boundaries of a disposal facility. New regulations under the Resource Conservation and Recovery Act (RCRA) require that once hazardous waste constituents are detected beyond the limits of the disposal area, a program to define the rate and extent of contaminant migration must be instituted. Future regulations are likely to include even more stringent groundwater protection criteria. The implications of both the existing and probable future groundwater protection and monitoring requirements in terms of using geologic containment as a means of disposing of hazardous waste are explored in this paper.

Jan 1, 1981

he leaching behavior of palladium in ammoniacal solutions has been investigated by using the rotating disk technique in an autoclave. The study included the effect of rotating speed, temperature, oxygen pressure, composition of ammoniacal solutions, and catalyst on the overall leaching rate. The dissolution of palladium in ammoniacal solutions was discussed in view of the thermodynamics and a kinetic model. Even though the potential-pH diagram suggests that palladium metal can dissolve in ammoniacal solutions at room temperature, it was found that the dissolution was too slow at temperatures below 100°C but was significantly improved at higher temperatures. It was also found that the rotating speed of palladium disk had no effect on the leaching rate. The apparent activation energy was found to be 69.7 kJ/mole. Based on the results obtained, it is concluded that the dissolution of palladium is controlled by chemical reaction.

Jan 1, 1997

Large deposits of eudialyte, a low grade zirconium bearing mineral, occur on the Southern Coast of Greenland in the Ilimaussaq intrusion. Various processes were tested in the laboratory to recover eudialyte from these ores, including flotation, leaching, gravity and magnetic separation. A combination of dry and wet magnetic separations has the advantage of simplicity and the least environmental impact for the location. This paper summarizes the results of laboratory testwork to develop a two-stage treatment process to recover the eudialyte by magnetic separation.

Jan 1, 1993

By Rameshwar Sah, Basavaraja Maribasappanavar, Sangamesh Desai, G. Balachandran, Ravi Kant Sagar

The present research work deals with the effective utilization of hematite ore containing goethite, kaolinite and gibbsite losson- ignition (LOI) phases in pellet making without deteriorating product pellet properties by optimizing the induration cycle especially drying and preheating of pellets. Adequate drying and preheating of pellets before sintering is of prime importance to sustain the desired properties of pellets. Green pellets of + 8 to − 16 mm size were prepared in a laboratory disc pelletizer and indurated by varying drying and preheating temperatures in a laboratory Raising Hearth Furnace (RHF). Produced pellets were assessed for physical and metallurgical properties. Improvement in drying and preheating temperature simultaneously helped in mitigating fired pellets’ property deterioration. Drying at 300 °C and preheating at 750 °C helped in the maximum removal of matrix LOI from the pellets before firing and enabled the production of pellets of desired properties. Laboratory scale findings successfully implemented at existing 4.2 MTPA capacity pellet plant of JSW Steel Ltd. Vijayanagar and high LOI iron ores (IOs) utilised which resulted in reduction of average monthly pellet fines generation by ~2 wt. %.

Jun 4, 2022

By C. Bateman, F. Calizaya

"This study presents the results of three laboratory experiments on pressure balancing carried out at the University of Utah’s coal mine ventilation model. The model includes simulations of two working areas, one longwall mine gob, and a set of stoppings and seals. It also includes a pressure chamber between the longwall face and the gob. The model is ventilated by one main fan and one bleeder fan. A carbon dioxide injection system, equipped with flow control valves operated by a microprocessor, is used to pressurize the chamber and to maintain the pressure in the chamber slightly higher than that of the gob. During each experiment, fan pressures and stopping resistances were changed, the carbon dioxide injection rate was regulated, and the differential pressures across the stoppings were monitored so that the chamber pressure is always kept slightly higher than that the gob pressure. Result of these experiments are reported in this paper. INTRODUCTION Spontaneous combustion (Sponcom) is a safety hazard in underground coal mines. The history of coal mining in the US is replete with mine fires and explosions. Sponcpm accounts for approximately 17% of the total number of fires recorded in the U.S. since 1990. In the U.S., by law, worked out areas in coal mines must be either ventilated by a bleeder system or isolated by explosion proof seals. Experience has shown that seals are not airtight structures and that they allow some leakage of air into or out of the gob. In fact, seals “breathe in and breathe out” with changes in barometric pressure (Francart 1997, and Chalmers 2010). These changes in pressure affect not only the methane emission rate but also the ingress of oxygen to the gob, the lower the pressure behind seals is, the higher the ingress of oxygen. In mines ventilated by a U-tube exhaust system, the gob is often kept under negative pressure. Under these circumstances, an increase in barometric pressure may cause an influx of fresh air into the gob. This quantity may be sufficient to start self-heating of the coal, which can lead to spontaneous combustion. Depending on the coal characteristics and the ventilation conditions, self-heating of coal can start at temperatures as low as 35 ºC. If the heat is not removed it will increase the coal temperature leading to ignition and fire. The risk of Sponcom fires can be reduced by isolating the mine gob using rated seals, and implementing a suitable ventilation system. However, isolation seals are not airtight structures, thus some leakage of air is expected unless the pressure in the gob is neutralized. The alternative is to use a pressure balancing system. This requires a thorough knowledge of the ventilation system, the seal/stopping construction techniques, the airflow behavior in the gob area, and the gas build-up behind the seal line."

Jan 1, 2016

By Thomas S. Mackey

The industrial types, sources, and quantities of USA tin residues are identified and the methods of treatment reviewed. The effect of a lower tin price, due to a current major world surplus of tin metal, is mentioned and covered in some detail. The names and locations of over 100 USA firms recovering tin residues are listed. Current smelting and refining charges are included to convert the residues into tin metal and alloy. The impact of the suspension of the LME daily tin price since October 24, 1985 to date, and the failure of the International Tin Council to support the Buffer Stock Manager are reported with comments.

Jan 1, 1986

By Mahaboob Basha Shaik, Shakuntala Tudu, Indrajit Paul, Chandra Sekhar, Neha Gupta, Amit Kumar, Srinivas Dwarapudi, Arvind Kumar Patel

In this study, the effect of colemanite and calcined colemanite (CC) addition on the properties of iron ore pellets is studied. The pellets are prepared in a lab without and with 0.2% colemanite and varying amounts of CC from 0 to 1.0 wt%in steps of 0.2%. A reference pellet is prepared under typical plant conditions, and the properties of the reference pellet are considered as the base value for improving the cold compressive strength (CCS) while maintaining the other parameters at an acceptable limit without altering the pellet. The study also aims to provide a detailed characterization of colemanite and calcined colemanite to better understand their behaviour during firing. The lab-scale results show that the CCS of pellets made with 0.2% colemanite was reduced by 222 points (60%) as compared to the reference pellets due to crack formation during firing. The results show an improvement in the CCS of the indurated pellets with CC dosage up to 0.4%, and decreasing strength is noted thereafter. It is observed that the swelling index increases with the increase in calcined colemanite dosage. To simulate plant conditions, reference pellets and pellets with optimized CC dosage were fired in a plant furnace.

Oct 16, 2020

By Richard Giffen, Martha Gross, Luca Pellegrini, Pa Ousman Njie

The Hampton Roads Bridge-Tunnel (HRBT) Expansion project in Virginia includes parallel 1.5- mile (2.4 km) tunnels constructed using a tunnel boring machine (TBM). The TBM launching and receiving shafts were excavated within the footprint of two reclaimed islands abutting the navigation channel for the Port of Virginia. The shaft excavations—a circular tri-cell shaft at South Island, and a circular-rectangular twin-cell shaft at North Island—were supported by slurry walls up to 190 feet (58 meters) below the island surfaces. This paper describes specic design considerations for these shafts, as well as construction and uality-oversight aspects of their excavation and construction.

Jun 23, 2024

By Hans Adden, Anne Lehan, Markus Thewes

"1. INTRODUCTION AND MOTIVATION Traditionally design processes are focussed at creating new tunnels for lowest building cost. But the trend towards sustainable constructions in tunnelling has greatly increased in recent years. A critical subtask of this approach is to realize the potential for optimizing and reducing the life-cycle costs (LCC) of tunnels and their components. To evaluate underground infrastructure projects from an economic point of view is therefore a highly topical subject of public authorities as well as private companies participating in Public Private Partnerships (PPP) projects. Nowadays, in the case of public works contracts, the contracting authorities shall draw up rules not only for the design but also for life-cycle costing. Within the scope of the decision-making process of building a new tunnel, planning the maintenance activities or the refurbishment of a tunnel in operation, the decision-makers need detailed knowledge about the current and future financial conditions of the planned projects and selected sub-measures. But in practice, the initial costs still represent the primary decision criterion in the planning phase, whereas the subsequent or follow-up costs, respectively, are only estimated roughly. Although tunnels are the key components and the most costly parts of the transport infrastructure, only a small number of scientific papers deal explicitly with the calculation of life-cycle costs for underground infrastructure. And in these cases, most authors use as the starting point only the basic form of the Net Present Value method which is known as the frequently applied life-cycle costing technique in building construction. The present study explains the strategic concept of life-cycle costing and its fundamental instruments for operational implementation. It shows the necessity to take into consideration that there are fundamental methodical problems when the life-cycle concept is transposed without modifications from building construction to civil engineering. The paper will discuss in detail some selected associated problems with the net present value method. On the basis of operational and safety related tunnel equipment it is shown, what impact this may have on principle determining the LCC of tunnels. Selected best-practices of maintenance planning for tunnels undertaken by the German Ministry of Transport fill the theoretical approach of the concept with life and give a practical orientation. In particular government authorities but also construction companies are interested parties in modern cost management considerations. The reason for this development is the replacement of aged excisting structures and the advancement of technical standards. The increase in the total numbers of tunnels (Fig. 1) as well as the need for future re-investments in existing tunnels show the overall economic impact and justify the change towards the life-cycle perspective."

Jan 1, 2016

By K. Lang

The use of high-efficiency electrical submersible pumps (ESPs) for large scale, open pit mine dewatering operations provides a good example of how technology, products and services from the oil and gas industry can be adapted to the mining industry. In this case, the mine is Goldcorp?s Peñasquito in the Zacatecas state of Mexico, at the Peñasco and Chile Colorado open pit deposits. The technology, products and services are from Schlumberger artificial lift (AL) and Schlumberger industrial water services (IWS). Overview of high-efficiency ESPs This section provides a brief description of the basic components, specifications and operating capacity ranges for the ESPs compared with traditional or conventional dewatering well pumps. This information helps to establish how ESPs provide certain functional and economic advantages over conventional pumps in a mine dewatering application. A schematic of a high-efficiency ESP in an oil and gas (O&G) application is shown in Fig. 1.

Sep 1, 2013