Search Documents

By George J. Conroy

Results of a long-term program of electrical parameter measurement in under-ground coal mine working sections, performed by The Pennsylvania State University under U. S. Bureau of Mines sponsorship, are utilized as the basis for an analysis of the electrical energy requirements during operation. A model section is hypothesized, developed from the average or most representative characteristics as determined from tabulations of the measurements. Performance factors of the model section's machine complement are then analyzed, particularly with regard to the energy required per ton of raw coal cut and delivered from the section. Results are given in kilowatt-hours per ton.

Jan 1, 1977

By George Anagnostou

Time-dependent ground behavior may have important implications for the construction process or the life of a tunnel. The paper gives a concise overview of the influence of time on the deformations and the stability of underground openings, including topics such as face stability in soft ground or the time-development of pressure or deformations in squeezing or swelling rock. While keeping in mind practical questions of tunnel engineering, emphasis is placed on understanding the observed time-dependency, on the underlying mechanisms (such as pore water pressure dissipation or chemical processes) as well as on the respective inherent prediction-uncertainties and design-uncertainties.

Jan 1, 2007

By S. Pastor, S. Hahn

"As the concept of autonomous haulage systems (AHS) moves from prototypes to production-ready applications, the operating performance of the haul road will become critical to the overall success of autonomy in mining. Deterioration in road performance will require remediation, human intervention and significant, albeit temporary, changes to operating procedures, to accommodate road maintenance. With autonomous trucks comes the opportunity to reduce road formation and operating width. This will, therefore, generate potentially significant reductions in stripping ratios and improvements to mine economics, but only if the design of the road, and its associated deterioration rate, is predictable and manageable, based on the materials used to construct the road and the maintenance interventions to be carried out on the road.This article presents the assessment of a digital photogrammetric approach to the characterization of a mine haul road surfacing, or wearing course material. Design and maintenance parameters for these roads are currently determined partly from physical particle size distribution (PSD) assessments of ‘in-road’ material. However, this approach does not accommodate the need, nor leverage the benefits from, AHS. The digital imaging approach is assessed in this article, using two standard digital analysis software tools, together with in-service mine haul road wearing course samples and images that are analyzed to determine the applicability and reliability of the approach to deliver a real-time assessment of haul road surfacing conditions and thus to identify the road maintenance interventions required to address deterioration.Enhancements in mine road design, construction and management for the past 20 or more years has largely been focused on short-term tactical needs. These improvements have not been matched by advances in the fundamental technologies that underpin mine road design and management and, although the quality of mine roads have probably"

Jan 1, 2015

By Thomas E. Ban

During recent years fuel consuming industries of the United States have been caught between environmental restrictions and the uncertainty of obtaining an inexpensive fuel. With the advent of the National Energy Act of 1978 there has been added impetus to switch from gas and oil to coal. For industrial furnaces and boilers that were designed to bum coal, returning to an available compliance coal might be feasible. However, furnaces and boilers designed for gas or oil cannot reasonably be converted to coal unless the coal is initially gasified. All cases, nevertheless, depend upon the availability of an adequate structured coal of a compliance composition, a challenge to the coal mining industry. The foregoing problems have contributed to the current energy-coal crisis of today's economies. It therefore would be worthwhile to capitalize on previous experiences of the mineral processing industry.

Jan 1, 1979

By Sam Lo Grasso, Carlos Herranz Calvo, Stuart Warren, Ted Giesing, Charles Marchesano

Mott MacDonald and Project Management Advisors are providing Technical and Project Management services for San Diego County for the Courthouse Commons Project. The Courthouse Commons Project involves the redevelopment of three downtown blocks owned by San Diego County and construction of an Inmate Transfer Tunnel between the County Central Jail and the San Diego Central Court. The tunnel will be 327 feet long, crosses the San Diego Fault and is being constructed using the Sequential Excavation Method (SEM). This paper discusses the history and procure‑ ment strategy for the project, the technical aspects of the transfer tunnel and the con‑ struction progress of the tunnel to date.

Jun 13, 2021

By Djavid Mohammad

Over the next several years, the storage capacity of the Metropolitan Water Reclamation District of Greater Chicago?s Tunnel and Reservoir Plan will be increased by 14.8 billion gallons through the addition of two large off-line reservoirs: the McCook and Thornton Reservoirs. The Thornton Reservoir will be constructed at the terminus of Calumet TARP System. The constructed TARP system will be connected to the Thornton Reservoir via connecting tunnels and gates systems. The connecting tunnels will comprise of: an upgradient transition tunnel, steel lined bifurcated tunnel for conveyance and control of flow, downdradient transition tunnel, and energy diffuser at tunnel portal. A large, approximately 250-foot-long, 69-foot-wide, and 40-foot-high, rock cavern will be excavated at an average depth of 320 feet to house the bifurcated tunnel system and associated six large control gates, each 12.5-ft by 28-ft wheel gate. Presented in this article are discussions about the TARP system, the Connecting Tunnels and gates Project, regional rock conditions, evaluation of reservoir?s wall stability for evaluation of tunnel penetration, and design challenges facing during design of the: rock cavern hosting the bifurcated tunnel system and gates and associated tunnels and shaft.

Jan 1, 2008

By Robert D. Coale

This paper will describe the copper concentrate slurry pipeline and pumping system between the concentrator and the port at Bougainville Copper Ltd. The operations of Bougainville Copper Ltd. are located on the island of Bougainville in the South Pacific. Geographically, it is the northernmost island of the Solomon Group but, politically, it is part of Papua New Guinea. Papua New Guinea is a United Nations Trust territory administered by Australia, having recently been given self-government, with independence scheduled for December 1974. (Fig. 1). The island is approximately 130 miles long by 30 miles wide, with the Crown Prince mountain range forming a spine along its length. The mountains in place are over 8,000 feet high with the mine located on the western flank at an elevation of 2,200 feet. Exploration on Bougainville for copper by Conzinc Riotinto of Australia (CRA) began in 1963 and by 1968, through geophysical, geochemical and diamond drilling methods, an orebody containing nearly one billion tons of ore grading approximately 0.48% Cu. and sane gold had been outlined. Bougainville Copper Ltd., the company operating the mine, is 53.6% wined by CRA, 20% mined by the government of Papua New Guinea with the public Folding the remainder of the shares. The first copper concentrate was produced in early 1972, with production for the first full year, 1973 being:

Jan 1, 1974

By Shuie Li, Taibai Li, Tao Hu, Zhongjie Wang, Xiang Ge

As one of the main power sources, lithium-ion batteries (LIBs) will continue to be applied on a large scale in the future market. Commercialized LIBs cathode materials contain various valuable metal elements including Li, Co, and Ni. The development of green and efficient recycling technology is essential. Deep eutectic solvents (DESs) have recently emerged as a new class of green solvents that could potentially be applied for the LIBs recycling industry due to their capability to leach the active materials without the introduction of environmentally hazardous reagents as used in conventional hydrometallurgy process. Considering the rapid progress, a critical review focusing on the progress and fundamentals about the overall efficiency has practical significance for the further advancement of this field. Herein, we briefly introduce the overall process of using DESs for LIBs recycling and specifically focus on the efficiency of each step. Current fundamental understandings and new experimental approaches to enhance the efficiency of the leaching process, the extraction process, and reusability are summarized. We expect this review article to inspire scientists to use DESs as powerful tools for advancing the frontiers of LIBs recycling.

Jul 30, 2022

By Wade Edward Speer

The Hiddenite District of Alexander County, NC has produced some of the world?s finest large emeralds since the first one was discovered 134 years ago. In fact, North America?s largest emeralds come from the district, making this one of the continent?s most unique gem deposits. In addition to emeralds, the Hiddenite District is also famous as the discovery site for the rare spodumene mineral hiddenite, first identified in 1881. Nowhere else in the world do these two minerals naturally occur together. The emeralds are a unique color variety of beryl (Al2Be3Si6O18) with trace amounts of Cr+3 and V+3 substituting for Al+3. The hiddenite (LiAlSi2O6) crystals also exhibit emerald green color due to traces of chromium. Consisting of three large deposits and numerous prospects, the district encompasses an area of 10 km2 (4 sq miles) centered on the small town of Hiddenite. Operations at the Adams, Ellis and North American Emerald Mines properties have been productive at irregular intervals since the 1880s. Currently, only the North American Emerald Mines property is being mined on a regular basis. Recent activity there has exposed a 3-hm2 (7.4-acre) pit with depths of 25 m (82 ft) that provides the best exposures of unweathered bedrock seen in the district in more than 120 years. Although no official records exist, public and private data indicate that the production of the entire Hiddenite District from 1880 to 2007 is about 70,000 carats of emerald and 20,000 carats of hiddenite. The bulk of the emeralds came from the North American Emerald Mine property (NAEM, formerly known as the Rist Mine) where sustained mining replaced the previous sporadic prospecting in 2000.

Jan 1, 2009

By P. Amelunxen

Over the past several years, the combination of higher energy and steel costs and the recent commercial deployment of high-pressure grinding rolls (HPGR) technology in hard rock mining have led many multinational mining companies to evaluate the suitability of HPGR technology for their particular comminution circuits. HPGR technology is perceived to require a higher capital investment while delivering lower long-term operating costs. This paper undertakes a critical evaluation of this perception. By evaluating the capital and life-of-mine operating costs of competing circuit designs for soft, medium and hard ores, the HPGR break-even point can be identified, at which the incremental capital cost of an HPGR circuit is equivalent to the net present value of the projected operating cost reductions. For ores with hardness parameters above the break-even point, HPGR circuits could offer economic benefits, while for softer ores, SAG mill/ball mill/pebble crushing (SABC) circuits are likely to be more economical and energy efficient. This evaluation considers both an SABC reference circuit and a traditional stage crushing configuration. Other influential factors are also discussed.

Jan 1, 2011

By D. Berberick

Hecla?s Lucky Friday Mine is a deep, underground producer of silver, lead and zinc in the Coeur d?Alene mining district of northern Idaho. Main access into, and production from, the mine is via the Silver Shaft, a 5.5-m (18-ft) diameter, concrete lined shaft sunk by J.S. Redpath to an original depth of 1,890 m (6,200 ft) in the early 1980s. The shaft is divided into four compartments (Fig. 1), with sets made of 225 mm x 175 mm (9 in. x 7 in.) hollow structural section (HSS) steel buntons and 150-mm x 150-mm (6-in. x 6-in.) HSS dividers spaced every 4.5 m (15 ft) down the length of the shaft. Two skip compartments on the east side of the shaft are equipped with 125-mm x 150-mm (5-in. x 6-in.) HSS steel guides and 9-t (10-st) skips with three deck trailer cages for men and materials. The west side of the shaft is divided into a manway, and a fourth compartment that was originally designed for a service cage. Shaft services consist of a 250-mm (10-in.) a compressed air line and 150-mm (6-in.) sandfill line along the south side of the shaft, and 250-mm (10-in.) discharge (gray) water and 150 mm (6 in.) fresh water lines on the north wall. The mine?s primary 13.8 kV power lines, as well as communication lines are located on the west wall of the shaft. The production hoist is a 3.7-m (12-ft) diameter, double drum, double clutch, 2,238 kW (3,000 hp), direct current unit equipped, at the time, with thyristor drives. The 30-year-old drives would prove to be problematic during the rehabilitation project, leading to an upgrade to modern ABB drives later in the project, after the shaft rehabilitation was complete. The shaft had been subjected to the typical wear and tear of 30 years of operation, including intermittent sandfill and muck spills, and, in the lower areas, some corrosion. During those 30 years, the west compartment, originally designed for the service cage, could only be accessed from a work deck on top of the skips or from the manway.

By Fulvio Tonon

And Rabcewicz said ?tunnels should be driven full face whenever possible.? ADECO, which stands for ?Analysis of Controlled Deformations in tunnels,? now allows us to fulfll Rabcewicz?s dream in any stress-strain condition. In order to achieve that dream and its consequent control over cost and schedule, however, NATM must be abandoned for the ADECO. The paper presents the basic concepts in the ADECO approach to design, construction and monitoring of tunnels together with some case histories, including: full face excavation for Cassia tunnel (width of 22 m, height of 14 m) in sands and silts under 5 m cover below an archeological area in Rome, Italy; Tartaguille tunnel (face area > 100 m2) advanced full face in highly swelling and squeezing ground under 100 m cover where NATM led to catastrophic failure, France; and 80 km of tunnels (face area > 100 m2) advanced full face in highly squeezing/swelling ground under 500 m cover for the high-speed railway line between Bologne and Florence, Italy (turnkey contract).

By P. R. Dugan

Sulfur removal from high sulfur coal has several objectives including: a) reduction of the atmospheric load that contributes to the problem of acid precipitation; b) reduction of ash, which contributes to decreased energy transfer in boilers, as well as ash disposal; and c) alleviation of the social and economic dislocations reluted to uneven geographical distribution of sulfur in coal reserves. Cost in relation to the value of refined coal will govern the development of an emerging coal refining industry. Estimation of the premium paid by power companies for coal with a low sulfur content is a good estimate of the value that will be added as the result of refining. Estimates of premiums paid in 1984 are $28.65/t ($26 per st) for reduction of total sulfur from 3’% to 1% S and greater than $28.65/t ($26 per st) for removal below 1% sulfur.

Jan 8, 1987

Queensland?s underground coal industry, as a whole, has arguably the best gas monitoring systems in the world. Each mine utilizes real time, tube bundle and onsite ultra fast gas chromatograph systems. Queensland?s mining legislation has specific requirements for mine gas monitoring but there is no requirement for all three techniques. Industry has however identified the need for all three and adopted this as a standard, resulting in over sixty thousand gas results collected each day. Automated monitoring systems are programmed to alarm for gas concentrations, gas ratios and explosibility. These alarms are then used to initiate predetermined actions to take control of the situation and prevent the compromise of safety to workers and the loss of resources. Dedicated software packages have been developed to assist in the interpretation of the large volume of results generated. The real time systems are used for real time warning, essential for incidents such as belt fires. Tube bundle systems suit long term trending used for identification of the onset of spontaneous combustion or for the determination of explosibility during the routine sealing of worked areas. Gas chromatograph analysis is used to provide a complete analysis and provides results for hydrogen and ethylene, key gases used in the assessment of spontaneous combustion. It is also crucial during significant spontaneous combustion events and coal fires to use gas chromatography to determine the explosibility status of the underground atmosphere otherwise the severity of the situation is likely to be under estimated. This paper outlines the need for all three techniques for assessing the underground status and outlines advantages and disadvantages of each.

Jan 1, 2009

By M. Gangal

CANMET-MMSL, in cooperation with Dry Systems Technologies and Quinsam Mine, conducted a study to determine the effects of B50 biodiesel on the emissions of a flameproof diesel power package in comparison with mining diesel fuel for application in underground coal mines. The emissions testing for coal mine application requires that the intake air mixture to the engine should be at 1.25 percent methane by volume in air. The tested power package system included a naturally aspirated, mechanically-controlled diesel engine with a diesel oxidation catalyst (DOC), a heat exchanger, flame arresters, and a low temperature disposable diesel particulate filter. The engine dynamometer tests were conducted at the CANMET-MMSL Diesel Emissions Research Laboratory in Ottawa using the ISO 8178-C1 test protocol. The separate and combined effects of a B50 biodiesel blended fuel, and with and without 1.25% methane enriched intake air were measured on a diesel power package. Fuelling the baseline engine (without methane), with B50 biodiesel blend reduced carbon monoxide (CO) by 44%, and increased nitrogen dioxide (NO2) by 19%, and particulate matter by 31% relative to the mining diesel fuel. Similarly, injection of 1.25% methane to the intake air for baseline engine with mining diesel fuel increased engine power by 15%, CO by 124%, and NO by 15%, and decreased NO2 by 13%. The effect of B50 biodiesel relative to the mining diesel for coal mines application (with methane for both fuels) was to reduce CO by 27%, and NO by 6%, and increase NO2 by 23%, with no change in engine power. The overall results indicate that the minimum ventilation rate for the equipment application in coal mines with B50 biodiesel was 4.11 m3/s (8,700 cfm), slightly higher than the ventilation rate of 4.01 m3/s (8,500 cfm) with the mining diesel fuel. This slight increase in ventilation rate for B50 biodiesel fuel was due to an increase in NO2 at one of the operating test points, and the ventilation rate for this equipment was governed by NO2 in the exhaust gas.

Jan 1, 2009

By J. Olsson

Introduction Stainless steel has by tradition been a common construction material for hydrometallurgy processes and the most common grades can be found amongst the ASTM 300-series, i.e. austenitic grades of type 304L, 316L and 317L. However, there are a number of new grades available today, which imply more cost effective solutions for those designing plants where good resistance to acids, containing the desired metal ions, often contaminated with chlorides and other halides, is the key issue. There are austenitic-ferritic or duplex grades having the same or even better corrosion resistance than the austenitic grades and approximately twice the strength, which enables design in thinner gauges, which in turn implies less weight and less cost. They have also excellent engineering properties, enabling fabrication of process equipment, machinery and different types of tanks. On top of that, they contain less nickel and molybdenum than their austenitic counterparts, which implies not only lower cost for alloying elements, but also a more stable price when considering the price fluctuations for these alloying elements during the last years. This paper describes briefly the family of duplex stainless steel and it presents a number of relevant corrosion tests where duplex grades have been compared with austenitic grades. The results have in several cases been verified by in-plant exposures in zinc and copper production plants. It also describes applications and experience of duplex grades within a variety of hydrometallurgy plants. Installations of highly alloyed austenitic grades will be described as well. The corrosion tests and service experience reported cover hydrometallurgical processes based on sulphuric acid.

Jan 1, 2007

By Dr. Peter J. Conroy

The current study is part of the U.S. Department of Energy's (DOE) on-going subsidence research program. The long-term objective of the DOE program is to develop analytical methods of subsidence prediction applicable over a broad range of geologic and mining conditions encountered in the United States. The DOE currently has several contracts in progress to develop a sound data base that can be used in the development of predictive models. Dames & Moore is currently under contract to the DOE to collect and analyze detailed subsidence and hydrologic data from a coal mine employing longwall mining methods in the Eastern Coal Province. Work under Contract No. DE-AC22-80PC 30335 began in October of 1980 and will continue through September of 1984. This paper summarizes the work that has been completed through September of 1981 and presents the results that have been achieved during this period. Technical difficulties encountered during both the installation and monitoring phases are discussed, and recommendations for future work are presented.

Jan 1, 1982

By R. J. R. Cornelissen

The elimination of the incidence of silicosis in employees in industries such as mining and pottery is an ongoing international initiative. After many decades of industrial activity in these industries and many dollars spent on preventative measures, silicosis is still occurring. The exposure-prevention measures taken so far have certainly improved the working environment dust concentrations; however, the illness is still regularly diagnosed in workers. More funding is needed for interventions to improve working conditions. Many aspects of dust prevention and suppression will be researched and exposure assessment methodologies and equipment will need to be reviewed for the purposes of improvements in effectiveness. This paper presents results from laboratory tests carried out on gravimetric sampling pumps and cyclones. It highlights the erratic flow produced by gravimetric pumps of three different manufacturers who claim their respective pumps are equipped with flow stabilisers. The standard BS EN 1232:1997 is used as a basis for the tests. A method, albeit impractical for fieldwork, is shown for the elimination of the pulsation in the flow. This method serves to prove the method and protocol used in this study. The pressure loss caused air-flow resistance of cyclones is measured. The air inlet aperture size of cyclones is measured. The large discrepancy in the two criteria between individual cyclones is shown. The paper concludes that all the pumps tested failed the prescribed limits of BS EN 1232:1997 regarding the pulsation of the gravimetric sampling flow. The difference in flow characteristics of the cyclones, together with the erratic flow produced by the pumps, throws into question the accuracy of the exposure assessments. It is suggested that substantial resources be channelled towards solving these flow problems in parallel with measures taken to reduce exposure. In principle, the accurate assessment of exposure and dust concentration levels is a prerequisite for effective management of the problem of silicosis.

Jan 1, 2009

By James W. Estep

The sulphur shortage that has occurred in the past two years has directed attention more and more toward sour natural gas reserves, Wellhead values of sour gas vary widely depending upon the acid gas composition, location, market conditions, and necessary processing charges. Preparation of a saleable residue gas is considerably more involved and expensive than that normally encountered in treating a sweet gas. Recent revisions in sales gas specifications have increased capital costs and processing charges. The presence of hydrogen sulphide and carbon dioxide in a natural gas contributes to shrinkage factors that may approach 50%. Fuel required by the gas sweetening process and sulphur slant tail gas incineration also contributes to a further reduction in the volume of residue gas available for sale. The additional processing facilities involving gas sweetening, mercaptan removal, expanded utilities, sulphur recovery and sulphur handling, all demand additional operating and maintenance staff. A favorable sulphur market under certain conditions may justify the processing of sour gas whereby sulphur is either a by-product or a co-product, Five typical cases involving different compositions of sour gas are presented for evaluation. Capital costs, operating problems, and operating costs are presented in detail for full economic evaluation

Jan 1, 1967

By K. E. Yassin, A. Yehia, M. Amar

Phosphate fines (size ≤ 45 μm), from the Red Sea Region, Egypt, were subjected to beneficiation process to recover the phosphorite grains from such fines. The sample is characterized by low P2O5 content (18.78%) associated with gangue minerals such as silica (22.77% SiO2) and carbonate (2.01% MgO) indicating its low grade. Phosphate pre-concentrate was prepared by gravity separation, using Falcon, where 63.37% of the phosphate, with 24.94% P2O5, 1.46% MgO, and 10.54% SiO2, was firstly recovered reducing the mass flow to the subsequent beneficiation process. However, the gravity tailing was the feed for the reverse phosphate flotation using bench scale column flotation where oleic acid was used as a carbonate gangue collector and amylase enzyme as a phosphate depressant. Under the appropriate flotation conditions (0.1% amylase, 5·10−4 mol/dm3 oleic acid, and temp. 30 °C), phospho-concentrate assaying 0.61% MgO, 13.14% SiO2, and 27.85% P2O5 with a P2O5 recovery of 55.45%, was finally obtained without the use of expensive depressants, e.g., phosphoric acid or sodium silicate. A tentative flow sheet for the whole process was postulated.