Search Documents

By Joseph Cervik

The mined coal bed and surrounding strata are both sources of methane which must be control led during mining. During developmental mining, the mined coalbed is the primary methane source; during retreat longwall mining, the primary methane source is the overlying strata. Underground technology is being developed to control both sources. This technology involves drilling long horizontal drainage holes into the mined coal bed and relatively short holes (less than 152 m or 500 feet) into the overlying strata. Because of the large volumes of methane that flow from such drainage holes and the limited ventilation available for in-mine dilution, underground pipelines are used to transport the drained gas to the surface. Large- scale in-mine degasification demonstrations showed reductions in methane flow of up to 70% during developmental mining.

Jan 1, 1981

By Richard S. Klein

Frozen coal creates severe handling problems. Utilities require uninterrupted supplies of coal to meet their increasing coal consumption rates. Difficulties incurred due to frozen coal result in more costly downtime for the utilities. Air cannons, vibratory hammers and thaw sheds are examples of mechanical devices used to break, crack or thaw frozen coal. Recently chemical treatments have been developed as preventive measures. The freezing of coal depends upon a number of factors, of which one of the most significant is surface moisture. The more there is, the larger the frozen coal problem. Slide 1 depicts a graph of frozen coal compressive strength as a function of surface moisture. Below a certain minimum value the coal will not freeze. Above this point, compressive strength is essentially a linear function of moisture over the range practically encountered. By surface moisture is meant the free moisture on coal having a normal vapor pressure as opposed to capillary moisture or inherent moisture. In addition to the straightforward freezing of coal surface moisture binding particulates together, frost formation occurs due to temperature gradients which develop in rail-cars and stockpiles .

Jan 1, 1980

By John Barakso

The Sam Goosly or Equity silver deposit is fundamental- ly a discovery based on the analysis and interpretation of reconnaissance geochemical samples. The discovery was made by Kennco in an area of heavy forestation and wide- spread cover by thin glacial debris. No major mines had been discovered in the vicinity of the discovery prior to the geochemical reconnaissance, and the interpretation of the geochemical results therefore was based on data available through geologic mapping and the sample collection process. In the period 1959-1961, PE. Hirst and his crew, in 1962- 1965 P.T. Blackand his crew, and in 1966-1967 C.S. Ney and P.T. Black and their crew collected geochemical samples from the area of what is now the ore body. Several of these samples were compiled and reanalyzed in the winter of 1966- 1967 for various trace elements, including fluorine. A strong, almost 16-sq-km (10-sq-mile) fluorine anomaly was projected along with a very weak heavy metal anomaly. On the basis of this anomaly, a chalcopyrite-bearing quartz monzonite was discovered in 1967. This was a misleading, noneconomic discovery not associated with the Sam Goosly discovery. The interpretation of the geochemical data by Barakso that summer indicated that another source was responsible for the fluorine anomaly. The conclusion was based on the assemblage of trace elements. Therefore C.S. Ney recommended further regional soil sampling to check the original data. The early results of this follow-up sampling found over 33 ppm silver. First float, then ore outcrop was found in the area of the silver anomaly. The attached reprints complete the development of the property after the discovery of the outcrop of ore.

Jan 1, 1990

By J. J. Antony

The Cactus Gold Mine is a joint venture comprised of Middle Buttes Partners Ltd. (CoCa Mines, Inc.--operator, T. Congdon and W. Carey) and Compass Mining, Inc. The project includes 2.4 sq. miles of contiguous mining claims and leases in the Mojave Mining District, Kern County, California, approximately B5 miles northeast of Los Angeles. The property is readily accessible year round by all-weather roads and is within 6 miles of the main line of the Southern Pacific Railway.

Jan 1, 1988

By B. K. Cantrell

The U.S. Bureau of Mines and others have conducted a number of occupational exposure surveys since the publication of the International Agency for Research on Cancer report of 1989, which labeled diesel exhaust as a probable human carcinogen. These surveys have assessed diesel exhaust exposure using measurement of diesel aerosol and/or specific polycyclic aromatic hydrocarbons as indicators of exposure. This paper reviews present diesel emission standards, available diesel exhaust aerosol measurement techniques, and the results of the occupational exposure surveys. In the surveys, diesel aerosol was emphasized because it is a major component of diesel exhaust, is suspected to contribute to the health hazard, and is readily measurable. Three primary aerosol measurement techniques were used: respirable combustible dust, size-selective sampling, and measurement of the elemental carbon fraction. Occupations surveyed included mine workers, railroad workers, forklift operators, fire fighters and truck drivers. The studies found mean diesel aerosol concentration levels in the range of 0.004 to 1.74 mg/m3? Highest aerosol exposures were in confined spaces such as mines where heavy diesel equipment is used. Polycyclic aromatic hydrocarbons typically are found at very low concentration levels and are not unique to diesel exhaust.

Jan 1, 1996

By R. Klimpel

Recent work has shown that the measurement of flotation kinetics in the laboratory is useful in providing guidelines on how operating sulfide flotation plant performance can be improved. This work outlines the influence of various factors on flotation kinetics such as collector/frother type and concentration, particle size, and frother blending.

Jan 1, 1981

By Hongwei Wang, PEIPEI CAO, Yongping Wu, JIANQIANG JIAO

In the fully mechanized top caving mining of steeply inclined, extra-thick seams with variable angles, the mechanisms of roof rock movement, failure, caving and filling are highly complex. This is due to the varying angle of coal seam in different areas, which makes rock–equipment stability control challenging. In this paper, the surrounding rock deformation and failure mechanisms, bearing structure of the overburden, and working characteristics of the supports are elucidated. The principle and key technologies of rock–equipment stability control are presented and applied to control the overburden of the regional failure and realize safe and efficient mining of the working face.

According to the Balandin's (1) "multiplet theory of catalysis", adsorption can occur only if atoms of the reactant molecules are congruent with surface atoms of the catalyst. Such a condition calls for certain definite geometrical relationships between the reactant molecules and the atoms at the surface of the catalyst. If such a match or geometrical 'fit' is not provided, the surface reaction will not take place. An appropriate analogy to this may be the lock and key theory that enzymes should fit a substrate just as a key fits a lock. Similar geometrical considerations in adsorption studies were made in connection with the flotation of minerals. Gaudin(2) and Gaudin and Preller (3) proposed that if the dimensions of collector ions are in registry with the mineral lattice, an ordered layer of adsorbed species is formed. They explained that the structural fit is one reason for good flotation of galena with xanthate. In another study, Bachmann (4) attributed the selective flotation of KC1 from NaCl with amine to the fact that the lattice parameter of the amine collector is closer to that of KC1. Schubert(5) investigated the flotation of various nonmetallic minerals with amine and pyridine, and related the dimensions of the collector ions with the anion distances of the mineral surface. He concluded that good flotation is obtained when the tolerance is within 20%. The geometrical theory has also been used by Groszek (6) to explain the preferential adsorption of n-paraffin onto the basal plane of graphite. The geometrical theory has thus been found useful in explaining adsorptive properties of an adsorbate relative to the substrate structure. The purpose of the present work is to examine the possibilities of a geometrical fit between sodium dodecyl sulfate and Cu(OH)2 surface, and to construct a crystallographic model of the surface compound.

Jan 1, 1974

By James G. Mock

The choice of equipment to be applied to a given installation by the Application Engineer begins with the data as presented to him by the user. This point in the relationship establishes a communication link, which will decide whether or not the correct piece of Overhead Equipment is applied at the most economic advantage to the user. The role played by the user cannot be minimized. No one knows better than he, just what work he expects to accomplish with this piece of machinery. However, all too often, he oversimplifies the requirements, and along with minimal crane and building parameters, merely refers to one of the following crane classifications as defined by The Crane Manufacturing Association of America, as shown in Figures 1, 2, 3, 4, 5, 6 and 7. This approach places the ultimate user in an unfair position, since he has then assumed the status of the machinery designer and must, therefore, assume the responsibility of the success or failure of the operation of that piece of machinery. If the user selects a Class "C" crane for his job requirement, when actually a Class "B" crane can adequately handle the work load, he is not offering the most economic solution to his company and added little to the cranes service capabilities.

Jan 1, 1973

By Greg Sanders, Michael Gilbert, James G. Shaughnessy

"A new raw water intake from the South Holston River to the Kingsport water treatment plant is under construction. The exploration for the 335 meter long horseshoe shaped tunnel design took advantage of the site topography along the alignment to better define the complex geology consisting of Knox Limestone and Sevier Shale formations separated by a fault zone. To assess the geological conditions and to determine the extent of the fault zone, a 183 meter long horizontal boring and geophysical investigation was performed along a portion of the tunnel’s horizontal alignment. Explorations defined the fault zone width at approximately 5 meters and packer testing along the alignment provided a means of estimating groundwater inflows. As the tunnel excavation advances, comparisons of exploratory data versus encountered conditions will be made. This paper provides details on the geotechnical investigation, lessons learned, and the influence of the geology on the tunnel design. PROJECT OVERVIEW The Kingsport WTP is supplied with raw water via the South Holston River. The City of Kingsport (City) owns and operates the Kingsport Water Treatment Plant (WTP). The existing raw water intake system, consisting of pumps, power supply, raw water piping and appurtenant facilities has been determined to be vulnerable to failure. The original Raw Water Pump Station (RWPS) was constructed in 1928 as part of the original Kingsport WTP project. The 1928 RWPS operated until 1970 when it was replaced by the existing RWPS. This existing system still utilizes the 1928 piping and piping tunnel. Improvements to the RWPS hydraulics and capacity are required to meet the City’s future water treatment needs. The system extracts water from the South Fork of the Holsten River and coveys it via three pressure pipelines to the WTP. The conveyance piping exits the RWPS, ascends approximately 23 m up a near vertical rock outcropping then enters a 120 m long tunnel. Upon exiting the tunnel the piping continues underground to the WTP. The drill and blast tunnel is horseshoe shaped and nominally 3.3 m high by 3.3 m wide. The easternmost 62.3 m of the tunnel is without any type of support. The remainder is lined with concrete. According to the City of Kingsport, the concrete lining was installed in the 1970’s as part of upgrades to the facility. An evaluation of the current facilities concluded that the conveyance piping was in poor condition and required replacement."

Jan 1, 2016

By I. Duckworth

P.T. Freeport Indonesia operates a mining complex located in the highlands of Papua, Indonesia. This district consists of both underground and surface operations. The East Ertsberg Skarn System (EESS) is one of the major orebodies in this district. Subsurface caving of the EESS has been carried out in a systematic series of mining lifts dating back almost 30 years. Present production is from the third lift (Deep Ore Zone), which is scheduled to peak at 80,000 mtpd during 2009, with this rate sustained through 2015. The orebody is proven below the existing caving level, with the next vertical block called the Deep Mill Level Zone (DMLZ). This paper presents an overview of the DMLZ Mine based on recent feasibility level study. The mine is being designed for a peak production rate of 29.2 million mtpy, with 1,803 total ore draw points spread over a panel caving footprint of about 1.3km by 375m. The present reserves for this mine total 501 million tonnes. Located 1,400-1,800m below the original surface, the DMLZ will be one of the deepest caving operations in the world. Production is scheduled to commence in 2015. Discussion is provided on most design aspects including; caving methodology and layouts, geotechnical predictions and risks, ore handling systems, ventilation design and associated infrastructure, high-lift pumping system, cost estimation and expenditure scheduling.

Jan 1, 2010

By N. Edmonson

The demand for sulfur divides into two major categories: agricultural and industrial. Most of the agricultural demand is related to the production of phosphate fertilizer products. Industrial demand is derived from the demands for a large number of products and is related to a variety of industrial processes, no one of which characterizes it in a simple way.

Jan 1, 1994

By S. J. Schatzel, K. M. Ajayi, E. N. Rubinstein, Z. Khademian

This study simulates the impact of a shale gas well casing breach near a longwall mine. Field studies are conducted to measure mining-induced permeability changes over the abutment pillar of a longwall mine, and a geomechanical model is developed in 3DEC, a three-dimensional numerical modeling code, to predict the aperture of fractures in the overburden at the study site. The predicted aperture values are used to determine mining-induced permeabilities and the results are compared with the field measurements. These aperture values are provided as inputs into fracture flow code (FFC), which generates a stochastic discrete fracture network (DFN) model for the study site and predicts the potential shale gas flow to the mine. Results from 100 DFN realizations are statistically analyzed using the bootstrapping method to compensate for notable variation in fracture geometry. The results show a significant difference between the gas inflow for nearby panels due to increase in the induced permeability during mining of the second panel. The average gas flow to the mine was calculated as 4.72×10−2 m3/ s (49 cfm) for a hypothetical breach at the Sewickley horizon during the first panel mining, 8.97×10−3 m3/ s (19 cfm) for a hypothetical breach at the Uniontown horizon during the first panel mining, 2.16×10−1 m3/ s (458 cfm) for a hypothetical breach at the Sewickley horizon during the second panel mining, and 8.07×10−2 m3/ s (171 cfm) for a hypothetical breach at the Uniontown horizon during the second panel mining. Depending on the mine ventilation system, this could result in methane concentrations exceeding regulatory limits. Hence, these findings provide insights into the potential risk of an unconventional gas well casing breach near a longwall mine under shallow cover.

Feb 15, 2023

A virtual reality approach is presented that can aid entities such as mining companies and land use planners in communicating a visual understanding of a mining operation to interested stakeholders, citizens? groups, and public committees. These visualizations are particularly useful in permitting, production planning and mining closures, contributing to accurate communication and evaluation of mine plans, ultimate land use and evaluation of potential design options A case study is presented, that was created using commercially available virtual reality tools, to emphasize the benefits of visualization technologies in the sustainable development of mineral resources.

Jan 1, 2003

By F. M. Benavides

The mining complex being analyzed consists of four mines and two processing plants located in an area where there are several existing modes of transportation. Figure 1 shows a map of the general layout of the four proposed mines and the two existing processing plants. The mines are identified by the numerals "I" through "IV" and the plants by the letters "A" and "B". A proposed overland conveyor would collect the product from all four mines and convey it to Processing Plant A. Alternate transportation systems are as follows: Railroad transport from Mines I and II to Plant B; Highway trucking from Mines I and II to Plant A; Off-the-road truck haulage from Mine III to Plant B and from Mine IV to Plant A. River transportation from the mines to the processing plants was not considered in this study under the assumption that the high capital investments for the loading and unloading facilities, in addition to difficult traffic problems, would make this mode of transportation unattractive.

Jan 1, 1980

By David Court, Rab Brown

The paper discusses the work in progress on the construction of the extension of the High Speed Rail line from the Channel Tunnel into the centre of London UK known as the “Channel Tunnel Rail Link” (CTRL), and particularly on contract 250 which involves the construction of two 5.3Km tunnels 7.15m diameter constructed with two EPB convertible tunnelling machines underneath the densely populated area of East London. In addition the paper will look at an innovative Alliance that has been formed between the Contractors and the Client’s Engineer involved in the construction of the London Tunnel Contracts

Jan 1, 2003

By V. T. McLemore

NMBGMR has been collecting data on uranium mining districts, mines and mills since it was created in 1927 and has converted years of historical data into a relational database that can be imported in ArcMap. The database includes information on mining districts, mines, mills, geochemistry, photographs, and bibliography. The available data includes location, production, reserves, geologic, geochemical, resource potential, and other data. The NURE stream-sediment data provides geochemical analyses for >27,000 samples collected in New Mexico during 1970s. The NURE hydrogeochemical data provides analyses for water samples. ArcMap includes location of individual ore bodies as polygons and incorporates the mines and NURE data as individual site locations. The purposes of these databases are to provide computerized data that will aid in identifying and evaluating resource potential, resource development and management, production, and possible environmental concerns, such as physical hazards (i.e. hazardous mine openings), indoor radon, regional exposure to radiation from the mines, background geochemical data and point-sources of possible pollution in areas of known mineral deposits.

Jan 1, 2010

By A. L. Mular

A great deal of effort is being expended by mineral processing engineers to acquire a basic knowledge of modelling and optimization techniques. Stimuli such as immediate process improvement, expanded process understanding, optimal flowsheet design and re-design, and the development of new and better control systems are goals which excite the imagination in terms of increased profits. To reach these goals, process models and efficient optimization strategies, regardless of their purpose, assume an important role. Consequently, few of us can argue that such efforts are of no value. The purpose of this paper is to review empirical modelling methods and optimization strategies which appear to be of value to mineral engineers.

Jan 1, 1972

By N. Paas

Diesel powered equipment has been operated in underground coal for more than 50 years. According to the Mine Safety and Health Administration (MSHA), there are approximately 3,000 diesel units operating in underground coal mines in the United States. This number is expected to reach 5,000 diesel units in 250 coal mines by the year 2000. Also, there are approximately 5,000 diesel units operating in metal/nonmetal mines such as trona, potash and salt mines: and more than 3,000 diesel units operating in Canada. This increased popularity of diesel powered equipment over trolley wire, electric trailing cable or battery powered equipment is because of improved safety, greater mobility, higher productivity and increased power of diesel equipment.

Jan 1, 1997

By Richard E. Gray

Virtually all structures show some signs of distress due to deterioration of the building components, to changed loads, or to changed support conditions. Changed support conditions result from ground movements. In mining regions many cases of structural distress are attributed to mining without considering alternative causes. This is particularly true of coal mining since it occurs under extensive areas. Coal mining is estimated to have already undermined more than eight million acres and may eventually undermine 40 million acres in the United States (HRB Singer, Inc., 1977). Other nonmetal and metal underground mines impact much smaller areas. Although it is sometimes difficult, even with careful study, to identify the actual cause of damage, persons responsible for underground coal mining should at least be aware of possible causes of building stress other than mine subsidence. This paper presents information on distress to structures and briefly reviews a number of causes of ground movements other than subsidence: Mass movements, dissolution, erosion, frost action, shrinking and swelling, yield into excavations and compressibility

Jan 1, 1986