Search Documents

By D. Nutakor

This paper presents the results of a study conducted on a slope failure that occurred in the Q7 mining cut at Rio Tinto's Bingham Canyon Mine. The slope failure occurred in a weak rock mass with an estimated rock mass rating of 25%. The failure mechanism was of the circular type, involving ten 15-m (50-ft) benches and covered a total width of 152 m (500 ft). The analysis used Adam Technology's photogrammetric method with a two-dimensional rock fall simulation program (RocFall software) to design a 3-m- (1 0-ft-) high berm located 7 m (24 ft) from the toe of the failed mass. Back and predictive analyses were performed on a cross-section through the slide using Slope/W software, resulting in flattening the interramp angle (IRA) from 44° to 38°. This design modification produced a factor of safety (FOS) of 1.14. Sensitivity analysis involving FOS vs. pore water pressure showed that FOS is sensitive to water saturation. A dewatering system using a series of horizontal holes drilled below the slide and dewatering holes drilled from a drainage gallery has since been established to improve the stability of the slope. Throughout the one-year period since this investigation, no significant slope movement has been detected by the slope stability radar, and mining is in progress below the failure.

Jan 1, 2012

By R. L. Morse

The thermodynamic program is similar to previous mine ventilation programs but has been expanded to consider the compressibility of air. The thermodynamic program does consider: 1) air density variations, 2) humidity changes, 3) intake, exhaust, and underground fans, 4) heat transfer between rock and air, 5) refrigeration of heating plants, both surface and underground, and 6) heat generated by equipment, both diesel and electric. 110st of the compressibility factors are handled in the branch calculations. The field survey necessary to supply-data for this program is quite similar to the basic base and leap-frog pair of stations method used with most incompressible mine ventilation programs. The thermodynamic program is a complete package of ventilation network analysis which can provide mine management with good operational control and planning of mine ventilation systems.

Jan 1, 1977

By H. L. Holden

The single line grinding circuit at Bond Gold's Colosseum mine consists of variable speed drive semi-autogenous (SAG) milling and secondary grinding with a fixed speed ball mill. There are several advantages and disadvantages of operating SAG mills with variable speed drives. Discussion in this paper will focus on the effects of variable speed SAG milling in relation to mill liner wear, grinding media consumption, and mill operating availability. Operating experiences, corresponding mill data, and pertinent design changes are also presented.

Jan 1, 1991

This paper presents the results of column flotation of a fine feed sample of Florida phosphate. A central composite design is used to study the main and interaction effects of parameters affecting column efficiency. The statistical design is also used to determine the optimum conditions. The results indicate that, depending on the experimental conditions, it is possible to achieve a concentrate of high grade and recovery. A concentration of 15 ppm of non-ionic frother is found to be enough to maximize the recovery at the pH of 9.5.

Jan 1, 1999

By D. P. Gold

Major sources and reserves of Cb/Nb, Ta, REE, Y, Sc, Zr, Hf, Cu, apatite and vermiculite may be concentrated in primary and secondary minerals associated with different stages and depths of emplacement in carbonatite complexes and kindred alkalic intrusive rocks. Exploration targets include: apatite and pyrochlore (Nb) in the plutonic and hypabyssal core and ring-dikes: bastnaesite (REE), strontianite, barite and fluorite in hydrothermal veins and cone-sheets (subvolcanic setting): thortveitite (Sc,Y) and vermiculite in metasomatized aureoles (fenites): high grade eluvial deposits of apatite and pyrochlore, and secondary REE, Nb, Ti. and V-minerals in supergene and weathered zones.

Jan 1, 1991

By Baojie Zhang

The main goal of this study was not only to investigate the effectiveness of the FGX Dry Separator for removing pure rock from run-of-mine coal producing a better feed stock for conventional coal preparation plants but also to optimize the FGX Dry Separator performance for producing a salable clean coal product without using the conventional wet coal preparation processes. A Model FGX-1 Dry Separator with feed throughput capacity of 10 tph was extensively tested at the Illinois Coal Development Park using two coal samples having distinctly different cleaning characteristics. Statistically designed experimental programs were conducted to indentify critical process variables and optimize FGX Dry Separator performance by systematic adjustments of critical process variable parameters. The coal cleaning performance of the FGX Dry Separator was evaluated for the particle size range of 63.5 x 4.76 mm in most cases, although FGX Dry Separator feed consisted of nominal -63.5 mm run-of-mine coals. The best cleaning performance obtained from the FGX Dry Separator is described by specific gravity of separation (SG50) and probable error (Ep) values of 1.98 and 0.17, respectively. The SG50 and Ep values for individual size fractions were as follow: 1.90 and 0.12 for the +50.8 mm size fraction, 1.95 and 0.18 for the 50.8 x 25.4 mm size fraction, 2.01 and 0.19 for the 25.4 x 12.7 mm size fraction, and 2.03 and 0.23 for the 12.7 x 4.76 mm size fraction. These process efficiency measures produced a clean coal with ash content of 13.38% from a feed coal with ash content of 34.45%. Ash content of tailings and middlings streams were 85.09% and 39.57%, respectively. Total sulfur contents of corresponding streams were 3.87%, 4.68%, 6.87%, and 4.62%. For a relatively easy to clean Illinois No 6 seam coal (Cleaning Index: 0.72), only about 0.42% of the clean coal (i.e., 1.6 float fraction) present in the feed was lost to the tailings stream. For a relatively difficult to clean coal (Cleaning Index: 0.53), about 0.98% of the clean coal present in the feed was lost to the tailings stream.

Jan 1, 2012

By J. J. McClellenand, R. A. Jankowski

Face ventilation and water sprays are the primary controls used on continuous miner sections to protect workers from respirable coal and silica (quartz) dust. Laboratory tests were conducted by the U.S. Bureau of Mines to determine the impact on respirable dust concentrations when increasing airflow from 3000 to 9000 cfm (1.42 to 4.25 m3/sec), water flow from 15 to 35 gpm (0.057 to 0.132 m3/min) , and water pressure from 80 to 200 psi (5.52 x105 to 1.38 x106 pa). The effective limits for each control and interactions between these controls were of particular interest. Initial analysis concentrated on defining the impact of the control parameters on the respirable fraction of the feed dust, which was a blend containing 90% coal and 10% quartz. Gravimetric sampling indicated that airflow had the most significant individual impact on respirable dust levels and resulted in reductions of 99% at the operator and 57% in the return. Regression modeling was used to predict dust concentrations at the operator and in the return. Significant interactions were observed between control parameters and often, defined the level for a control parameter where increases above that level did not significantly benefit dust control. Increasing airflow to 8400 cfm (3.96 m3/sec), water flow to 25 gpm (0.095 m3/min), and water pressure to 140 psi (9.65 x105 Pa) typically provided respirable dust reductions at both sampling locations, while optimizing use of control resources. After determining these relationships for the total respirable fraction, selected filters were analyzed for quartz content to define the impact on the quartz component of the feed dust. For the individual control parameters, airflow again had the most significant impact and resulted in reductions of 98% at the operator and 26% in the return. Regression modeling of the quartz concentrations indicated that no significant interactions between control parameters were present. At the operators location, airflow was the only parameter identified as having a statistically significant reduction for quartz dust. A reduction in quartz approaching 95% was observed for increasing airflow to 6000 cfm (2.83 m3/sec). Increases above 6000 cfm had little additional impact. In the return, a linear relationship between control parameters and quartz levels was observed with reductions of approximately 27% predicted for increasing any one control parameter to its maximum level. The synergistic impact of increasing all control parameters to maximum levels resulted in a maximum predicted reduction of 81%.

Jan 1, 1991

By Frank A. Jerabek

Problems of mine backfilling and fill material deposited underground, the characteristics and relationship between the deposited fill material and overlying ground, and the practical applications and limitations of hydraulic backfilling as ground support are discussed. A great variety of materials ranging from coal washery refuse to concentrator tailings is used as hydraulic fill. Some materials will solidify and cement; others will resemble quicksand, Hydraulic fill as ground support is more efficient in inclined mine openings than in horizontal mine openings, where it cannot be placed tightly to the back. This and other deficiencies of hydraulic backfilling led to the development of pneumatic stowing. Research work in hydraulic backfilling at the Pennsylvania State University is also discussed. This research work includes the investigation of segregation in the discharged fill slurry, the quantity of solids escaping in the drain liquid, the relationship of escaping solids to slurry concentration and discharge rate, and the compressibility of fine fill material.

Jan 1, 1965

By Carlton M. Ray, William P. Levy, Thomas Lindberg

"The District of Columbia Water and Sewer Authority (DC Water) is implementing its $2.6 billion DC Clean Rivers Project to reduce combined sewer overflows to the District’s receiving waterbodies and mitigate chronic sewer flooding in District neighborhoods. The First Street Tunnel project is a major component of the DC Clean Rivers Project, designed to mitigate sewer flooding and basement backups in the District’s historic and densely populated Bloomingdale neighborhood. Bloomingdale has been historically affected by sewer flooding and was severely impacted by four storms in the summer of 2012 that caused significant damage to homes, the environment and public property. As a result, DC Water accelerated the design and construction of the First Street Tunnel in order to mitigate the effect storms have on the undersized sewers serving the neighborhood. The infrastructure designed to mitigate flooding, including the tunnel, are located within the highly urbanized neighborhood – with some structures being less than ten feet from residents front door steps. The success of a large public works project of this magnitude and in this unique location depends on a well informed and supportive public. With the local community impacted by flooding but concerned about heavy construction impacts, this paper details the components of a successful public outreach plan and lessons learned throughout the design and construction process. Early identification of community mitigation, working cooperatively with stakeholders and frequent dissemination of accurate information required the project team to establish a culture of problem solving collaboration with the community. BACKGROUND Chronic Flooding in the Northeast Boundary Sewershed The Northeast Boundary sewershed, in which the Bloomingdale neighborhood is located, is served primarily by a combined sewer system and has a long history of chronic flooding problems during moderate to severe storm events. The sewer system that serves the Northeast Boundary drainage area was constructed by the Federal Government in the late 1800's when developed areas of the District terminated at what is now Florida Avenue. Since construction of the system, population within the sewershed area has grown at an exponential rate. In meeting the growing needs of the population, the District experienced development that transformed previously low-density rural areas into new communities. Impervious areas have increased drastically since the sewer system was constructed and consequently, the existing sewer system does not have the capacity to convey storms with return frequencies beyond the 2-year storm without flooding. As a result of the capacity limitations, many of the low-lying areas have become chronic flooding areas due to the surcharging of sewers."

Jan 1, 2016

By R. W. Plume

Gold extraction along the Carlin trend requires large withdrawals of ground water, which can be perched, unconfined at shallow depth, and (or) confined at depth. Five hydrogeologic units-Quaternary basin-fill sediments, Tertiary basin-fill sediments and sedimentary rocks, Tertiary volcanic rocks, Devonian to Ordovician siltstones, and Devonian to Ordovician carbonate rocks--form the framework for two aquifer systems that discharge along some reaches of the Humboldt River and its tributaries and are recharged by streamflow along other reaches. Ground-water withdrawals eventually could affect these stream-aquifer interactions. Further work is needed to quantify regional hydrologic processes and evaluate potential effects of mining on water resources.

Jan 1, 1992

By E. McCullough, S. Gaillard

"Diesel particulate matter (DPM) has been regulated by the U.S. Mine Safety and Health Administration since 2002 in underground metal and nonmetal mines. To demonstrate regulatory compliance, DPM samples must be collected and later analyzed by the U.S. National Institute for Occupational Safety and Health (NIOSH) 5040 standard method, but the FLIR Airtec DPM monitor can serve as a complementary engineering tool. The monitor is a handheld instrument that offers near-real-time measurements of elemental carbon (EC), which is a primary constituent of DPM. As part of an ongoing field study, the monitor was used to survey EC in an underground stone mine. This effort was aimed at determining spatial and temporal DPM variations in several key locations. The results of prolonged area monitoring—that is, lasting several hours — revealed that DPM concentrations were diluted substantially as air moved away from the primary production zone, but that concentrations could vary quite a bit in a single location from day to day and between seasons. DPM concentrations were generally lower in winter than in summer, which is consistent with increased natural ventilation airflows during winter. Using a modified sampling cassette, an attempt was also made to sensitize the Airtec monitor to allow for “spot-checking” of EC concentrations — that is, measurements made in several minutes. Preliminary field data showed that the sensitive cassette performed well in terms of providing accurate data that could be useful for rapid assessment of DPM. IntroductionDiesel particulate matter (DPM) is the solid fraction of the exhaust emissions from a diesel engine. It largely consists of elemental carbon (EC) and organic carbon (OC) (Birch, 2003). The World Health Organization International Agency for Research on Cancer classified diesel exhaust, including DPM, as a carcinogen (World Health Organization, 2012). It is believed to cause and/or exacerbate respiratory illness upon inhalation, deposition and retention in lung tissue. Because DPM exists in both the micro- and nanoparticulate ranges, it can bypass typical autoimmune defense mechanisms that keep larger particles out of the respiratory system (Ristovski et al., 2012)."

Dec 1, 2016

Critical safety tools to locate miners underground are featured by several exhibitors at MINExpo. Communication was the buzzword for health and safety products at the 2008 MINExpo, and it is still important in 2012. Products unveiled following the Miner Act in 2006 have been upgraded and improved. Saving lives and reducing injuries through better leadership, planning and practice is the goal of every mine professional.

Jan 1, 2012

By Wang Ding-heng, Wang Zhi-yuan, Nolan B. Aughenbaugh

The People's Republic of China has abundant coal resources with proven reserves amounting to 582 Gt (641 billion st). Recognizing coal as a major energy source on which to build the country's industrial and economic base, there has been a rapid increase in production since the founding of the People's Republic. In 1949, only 29.4 Mt (32.4 million st) of coal was mined. Production has increased to 576.5 Mt (635.5 million st), exclusive of Taiwan, at present, making China the third largest coal producing country in the world. Plans call for a 4-5% increase in annual production for the next 20 years. Coal constitutes 70% of the primary energy consumption in China. The remaining 30% is divided between petroleum and natural gas with 26% and hydropower with 4%. Coal use and consumption is divided as follows. General industrial use comprised 48.9%, power generation uses 20.1%, and coking accounts for 10.5% (6.3% for metallurgy and 4.2% for chemical industry). Domestic use such as home heating and cooking makes up 17.8% and coal-fired steam engines for railways uses 4.7%. Coal Districts Coal underlies about 1/18 of China's land area. It occurs in 30 provinces, autonomous regions, and municipalities. In addition, the western interior region, which has not been explored, may contain sizable reserves. Based on geology, geography, and administration, the coal fields can be grouped into five districts as shown in Fig. 1. The north China district, the heart of the industrial base for the country, has the most extensive and largest deposits of the five districts. This amounts to almost 40% of the country's total reserves. The largest coal basin with proven reserves of 181.4 Gt (200 billion st) and the most exploitable seams is located some 300 km (186 miles) southwest of Beijing (Peking) in Shanxi Province. Centered around Taiyuan, the compound field extends from Datong in the north to Xian in the south. Its western extension is not known fully. The Northwest and Northeast districts contain the second and third largest deposits. The biggest coal field in South China is located in the Sichuan and Guizhou Provinces near Chongqing. At present, it is not known if sizable coal measures exist in the Tibetan district. Coal Types China's coal varies widely both in age and rank. Geologically, coal measures were deposited from the lower Carboniferous (Pennsylvanian of the US) and Permian of late Paleozoic, mainly during the Jurassic of the Mesozoic and peri¬odically throughout the Cenozoic. Collectively, coal from the lower Carboniferous, Permian, and Ju-

Jan 3, 1983

By Christian Heinz, Doug Harding

TBMs can last for decades and be rebuilt project after project with proper maintenance. How successful can rebuilt TBMs be? At the DigIndy Tunnel System in Indianapolis, Indiana, USA, a rebuilt TBM was used to great effect. The 6.2 m diameter Main Beam, originally manufactured in 1980, bored 40+ km of tunnels and set three world records in its size class of 6 to 7 m, including a best month of 1,754 m. In this paper, the authors analyze the TBM rebuild, performance and lessons learned to make recommendations for future projects seeking to use rebuilt TBMs over long distances.

Jun 23, 2024

By M. R. Peterson

The U.S. Bureau of Mines has investigated new methods for increasing the selectivity in flotation by creating and regulating reagent concentration gradients within flotation columns at steady-state operation. Gradients were generated and traced in a water-only system with the use of fluorescent dyes, and the effects of various operating parameters on these gradients were investigated. From this investigation, it was found that both gradual and steep gradients could be generated in the froth cleaning zone, and that these gradients could be changed through the manipulation of both physical and chemical operating parameters. The application of reagent-gradient control to mineral systems could improve both flotation grade and recovery in commercial flotation operations without the use of additional flotation circuitry.

Jan 1, 1992

By R. E. Nivens

In the past, Newmont Gold Company relied on cement for their ore agglomeration process. With assistance from Betz Industrial, Newmont began Investigating the use of polymers for ore agglomeration. If gold recovery would not be jeopardized, then polymers could replace cement and possibly reduce operational costs associated with cement agglomeration. The following outlines the preliminary testing conducted to determine the feasibility of polymer agglomeration with Newmont's ore and the results of the test heap, which was constructed so the program could be examined under actual operating conditions. Similar polymer agglomeration testing has been successfully performed in other Nevada gold operations. By eliminating the need for cement, a polymeric agglomeration program could improve material handling operations, as well as offer the following additional savings. First, the polymer application uses only lime for adjusting basicity, the polymer does not contribute any alkalinity to the heap. Because lime is more soluble than cement, detoxification of the heap becomes much faster and less costly for the mine relative to rinsing cement alkalinity. The following graph compares the detoxification rate of cement and polymer over a 33 day cycle.

Jan 1, 1993

By N. Del Bel Belluz

Drilling underground in the Grasberg De-watering drifts has routinely hit water aquifers with high flow rates and pressures. Two types of holes are utilized; pilot-holes to probe ahead of the tunnel development to intersect aquifers ahead of the face; and de-watering holes to de-water rock formations that will drain water from the Grasberg pit and allow tunnel development to proceed safely. Recently, rates of 1050 psi static pressure have been recorded with flows from a NQ hole measured at 1350 gpm (US). The water flows can be slightly acidic, necessitating the use of stainless steel collar gear to resist corrosion. These rates were anticipated and contingencies were planned early to deal with these conditions. The collar gear is used to control water flows whereby the water is treated as an important resource. As a result, pm has established procedures to maintain safety of the drill crews, enable coring of the rock and to maintain safety of the miners who are driving the drifts.

Jan 1, 1998

By L. Zhou, J. P. Rider, T. W. Beck, J. A. Organiscak, Y. Zheng

The U.S. National Institute for Occupational Safety and Health (NIOSH)’s Pittsburgh Mining Research Division (PMRD) recently developed a series of models using computational fluid dynamics (CFD) to study gas distribution around a continuous mining machine with various fan-powered flooded bed scrubber discharge configurations in an exhaust curtain working face. CFD models utilizing species transport model without reactions in FLUENT were constructed to evaluate the redirection of scrubber discharge toward the mining face rather than behind the return curtain. The study illustrates the gas distribution in the slab (second) cut. The following scenarios are considered in this study: 100 percent of the discharge redirected back toward the face on the off-curtain side; 100 percent of the discharge redirected back toward the face, but divided equally to both sides; and 15 percent of the discharge redirected toward the face on the off-curtain side, with 85 percent directed toward the return curtain. These models are compared against a model with a conventional scrubber discharge where air is directed away from the face into the return. The models were validated against experimental data, proving to accurately predict sulfur hexafluoride (SF6 ) gas levels at four gas monitoring locations. This study includes a predictive simulation examining a 45° scrubber angle compared with the 23° angle for the 100 percent redirected, equally divided case. This paper describes the validation of the CFD models based on experimental data of the gas distribution results.

Jan 1, 2017

By L. Zhou, J. P. Rider, T. W. Beck, J. A. Organiscak, Y. Zheng

The U.S. National Institute for Occupational Safety and Health (NIOSH)’s Pittsburgh Mining Research Division (PMRD) recently developed a series of models using computational fluid dynamics (CFD) to study gas distribution around a continuous mining machine with various fan-powered flooded bed scrubber discharge configurations in an exhaust curtain working face. CFD models utilizing species transport model without reactions in FLUENT were constructed to evaluate the redirection of scrubber discharge toward the mining face rather than behind the return curtain. The study illustrates the gas distribution in the slab (second) cut. The following scenarios are considered in this study: 100 percent of the discharge redirected back toward the face on the off-curtain side; 100 percent of the discharge redirected back toward the face, but divided equally to both sides; and 15 percent of the discharge redirected toward the face on the off-curtain side, with 85 percent directed toward the return curtain. These models are compared against a model with a conventional scrubber discharge where air is directed away from the face into the return. The models were validated against experimental data, proving to accurately predict sulfur hexafluoride (SF6 ) gas levels at four gas monitoring locations. This study includes a predictive simulation examining a 45° scrubber angle compared with the 23° angle for the 100 percent redirected, equally divided case. This paper describes the validation of the CFD models based on experimental data of the gas distribution results.

Jan 1, 2018

By Z. Henderson, J. R. Saylor, L. Rojas-Mendoza

"Diesel particulate matter (DPM) is a major occupational health hazard in underground mine environments, even with available abatement technologies. Prior work has demonstrated that micrometer-scale water droplets, or “fog,” may be effective in removing significant number fractions of DPM from a conditioned exhaust stream. Here, a series of laboratory experiments are described which demonstrate that such a treatment can remove significant DPM mass from an unconditioned stream. The removal mechanism involved coagulation of the DPM and drops. The fog treatment removed about 45 percent more DPM mass on average than no treatment. Varying engine load, flow rate and fog droplet number density did not significantly affect the results under the range of conditions tested. IntroductionDiesel engines have seen widespread use for well over a century due to their relatively high thermal efficiency and fuel economy (Heywood, 1988). Recently, however, the adverse health risks of diesel exhaust have become increasingly clear. The term diesel particulate matter (DPM) is used to refer to the solid components of diesel exhaust, which are an ultrafine mixture of elemental and organic carbon (EC and OC) and minor constituents including sulfates and metal ash (Kittelson, 1997). DPM is generally considered to occur almost entirely in the submicrometer range. It is classified as a carcinogen (Occupational Safety and Health Administration, 2013), and epidemiological studies have demonstrated a positive correlation between long-term exposure to DPM and other combustionrelated fine particulates and increased cardiovascular and pulmonary diseases (Pope et al., 2002; McDonald et al., 2011). Many of the risks of diesel exhaust are associated with the physical and chemical properties of exhaust components (Heywood, 1988; El-Shobokshy, 1994; Kittelson, 1997). Exposures are generally measured and regulated on the basis of mass concentration. However, DPM number density and particle size are increasingly recognized as critical factors in terms of health outcomes (Bugarski et al., 2012; Kittelson, 1997; Occupational Safety and Health Administration, 2013; Pope et al., 2002)."

Jan 11, 2017