Search Documents

By James M. Neilson

In contrast to the rather generalized title of this paper, the subject of discussion will deal with two specific cases of sliding in glacial lake clays in northern Michigan. The slides in question occurred on lands owned by the Upper Peninsula Power Company a short distance south of Lake Superior. Slope failure problems have plagued the Company's operations for many years. It is hoped that this paper may provide some insight into the causes and possible mechanisms of clay slides in general as well as providing details of the two slides specifically cited. LOCATION The Upper Peninsula Power Company's Victoria facilities lie in section 29, T. 50 N., R. 39 W., in Ontonagon County, Michigan. The power site is situated on the West Branch of the Ontonagon River, approximately five miles southwest of the town of Rockland and only one mile to the southeast of the old mining location of Victoria. The area lies wholly within the Precambrian Shield and it is geologically similar to adjacent parts of Wisconsin, Minn¬esota, and Ontario. (Figure 1). THE VICTORIA HYDROELECTRIC SITE The Victoria hydroelectric power facilities were constructed in 1930 on a portion of the West Branch where meanders are conspicuously developed. The generating station is actually sited on an abandoned meander at a place where valley widening has occurred. Water is conducted from Victoria Dam through a 6000-foot, 10-foot diameter wood stove pipe - through a surge tank - and into the powerhouse where

Jan 1, 1971

By A. Gungor

Thermal treatment can significantly improve industrial comminution operations by reducing energy requirements and increasing mineral liberation. The assistance of thermal pretreatment prior to grinding by microwave heating is scrutinized in this study. For this purpose three copper ore samples with different chemical composition were used. To see the effect of microwave heating on ore; work index, breakage rate and breakage distribution functions of original and heat treated samples were examined. The results obtained in this study did not show significant improvement in the grindability characteristics of the studied ores with microwave heat treatment. The inadequate amount of microwave transparent matrix was the main reason for the absence of cracks and micro-fractures in the microwave heated copper samples.

Jan 1, 1999

By Carl Rampacek

Laboratory and small-scale continuous pilot-plant investigations made at the Tucson Metallurgy Research Laboratory of the Bureau of Mines have demonstrated that the copper segregation process is applicable to the treatment of oxidized and mixed oxide-sulfide copper ores regardless of the gangue constituents. The process comprises heating the ore to a temperature of 750° C. with small quantities- of sodim chloride and coke to produce metallic copper, which then is recovered by flotation. Tests were made on' 23 copper ores of different types containing 0.8 to 5 percent Cu, .The copper recoveries ranged from 73 to 96 percent in concentrates assaying 10 to 62 percent Cu, depending on the grade and type of ore, The direct operating cost for a 1,000-ton-per-day furnace and flotation plant is estimated at about- $3 per ton of ore.

Jan 1, 1960

By Donald J. Hill

To be successful, every organization within the mining industry must involve itself in researching and evaluating methods of loss control. The appraisal and evaluation of accidents and injuries is required to determine the costs of loss producing practices and conditions. This involves all of an organizations disciplines that concern themselves with a more efficient and cost effective organization. To come to know the cost of your safety program or how much is expended yearly for each employee on safety; to know what your safety costs are per man-hour or per ton-produced; to know what the health, medical and compensation costs are for any given incident are just a few of the important facts and figures that the safety management of a given organization needs to know to operate in the mining industry today.

Jan 1, 1984

By T. R. Ellis

"In August 2013, the Appraisal Practices Board of the U.S. Appraisal Foundation issued its “APB Valuation Advisory #4 - Identifying Comparable Properties,” which contains analysis and examples that may suggest a broader meaning of the term “comparable properties” than is current convention in real property value appraisal in the United States and internationally. The advisory is directed at the appraisal of real property of all kinds, including interests in mineral properties, as indicated by the inclusion of two mineral property appraisal papers in the appendix that lists suggestions for further reading.This paper firstly reviews as background the historical meaning of a comparable property, with its perceived constraints, against real-world examples of transacted mineral properties that are adjusted to subject properties to provide market value indications. The advisory’s findings are then examined and evaluated as to whether they may influence and benefit the work of mineral property appraisers, particularly in situations where their sales comparison analyses may be challenged. The conclusion is that the combination of constraints that the advisory’s findings specify for use of the term “comparable” will for mineral properties be met infrequently or rarely. As a result, mineral property appraisers are advised to avoid using the terms comparable or “comp” when referring to transactions of mineral properties that they analyze to derive data for appraising the value of their subject mineral properties. IntroductionA mineral property appraiser rarely finds a sale of a mineral property that meets the literal meaning of the term “comparable sale,” by being directly comparable to the subject property of the appraisal in all factors of significance in the determination of the value of the property interest being appraised. Real estate appraisers have long used a more liberal interpretation of the meaning of comparable sale and its commonly used abbreviation, “comp.” Real estate appraisers compare sales to their subject property on the basis of price per hectare or acre of land and price per square meter or square foot of building floor area. Adjustments totaling to within the range of +30 to -30 percent from the sale property to the subject, before factoring in the property area, have generally been viewed as appropriate for the sale to be considered a comparable sale."

May 1, 2016

By James E. Palmer

Geologic constraints on mining and recoverability include the following: coal seams too thin or thick for conventional mining methods; coal seams with insufficient stratigraphic separation; unstable roof or floor strata; discontinuous or lenticular seams; coal seams that have high dips or are intensely faulted; water problems due to proximity of aquifers; and coal quality problems such as excessive sulfur, ash, chlorine, sodium, etc. The demonstrated reserve base for western coal of 220 billion tons is considered misleading as it does not adequately incorporate the above parameters in estimating procedures. Current reserve base estimating procedures involve an abstraction of data from generalized resource estimates. The authors believe the reserve base should be determined independently beginning with well-known deposits, with all mining and recoverability constraints fully incorporated.

Jan 1, 1981

By G. Guzman, L. Sevilla, M. Botz

"Newmont Mining Corporation operates the Yanacocha mine in Perú and the gold milling section of the property includes a Sulfidization-Acidification-Recycle-Thickening (SART) plant to remove copper from pregnant leach solution. Since its commissioning in 2008, the plant has been intermittently operated as needed to remove copper upstream of a carbon adsorption circuit. However, starting in 2015 Newmont expects the plant to operate on a more continuous basis in response to higher copper ores that will be processed in the gold mill. In anticipation of this, Newmont conducted a campaign in May 2014 with stockpiled high-copper ore to evaluate performance of the SART plant with elevated levels of copper in feed solution. Results from the campaign demonstrated the SART plant is capable of efficiently treating high-copper leach solution. During the campaign, leach solution copper levels ranged from about 100 to 700 mg/L, and copper removals ranging from about 56% to +99% were achieved. The median copper removal efficiency observed during the campaign was about 94%. The primary plant modification determined necessary following the campaign was the need to improve consistency with sulfide dosing. INTRODUCTION Copper removal from cyanide leach solution can be affected through the addition of sulfide at acidic pH to precipitate copper sulfide as a solid. There has been renewed interest in the process in the past several years due to the increasingly common issue of high copper levels in cyanide leach solutions. The term Sulfidization- Acidification-Recycle-Thickening (SART) is used as an acronym for the process according to the primary unit operations utilized. At a pH of approximately 4.0 to 5.0, the addition of soluble sulfide to a copper-bearing leach solution will result in the precipitation of copper sulfide (Cu2S) solid. The overall acidification and sulfidization reaction is (assuming the use of sulfuric acid for pH adjustment): 2Cu(CN)3-2 + 3H2SO4 + S-2 ? Cu2S(s) + 6HCN(aq) + 3SO4-2 The above reaction is written relative to the copper-cyanide complex 2Cu(CN)3-2, though analogous reactions also take place with the other common copper-cyanide complexes Cu(CN)2- and Cu(CN)4-3. Sulfide in the above reaction (S-2) is normally supplied as sodium hydrosulfide (NaHS) purchased in solid or concentrated liquid form. Two characteristics of this reaction that are beneficial to a leaching operation are: 1. Copper is removed from solution as Cu2S (synthetic chalcocite) solid, which can then be sold to a smelter for its copper value. 2. Cyanide that is complexed with copper in the leach solution is released as free cyanide, thereby regenerating cyanide that can be recycled to the leaching operation for continued use."

Jan 1, 2015

By N. A. Abdel-Khalek

The objective of this investigation was to compare the results of counter-current flotation column versus conventional flotation cell for the cleaning of a sulphur ore and its discrete size fractions. The tests were carried out using diesel oil as a collector and alcohol as a frother. Generally, flotation column produced concentrates of higher grade. For example, the grade of a rougher concentrate for a given feed obtained with the column increased by 33% higher than that produced with the flotation cell. Such higher grade could not be obtained using conventional cell even after 3 cleaning stages. Moreover, the column gave superior results for flotation of fine and ultrafine particles.

Jan 1, 1991

By James E. Lawver

During the past century, the Florida Phosphate Industry has established an enviable record of innovative technology in nearly all aspects of mining and beneficiation. A notable exception is the lack of technology to improve the present practice of storing waste clay in earthen dams. The rule which has been adopted by the Department of Natural Resources states, "Since storage of clay wastes for long periods of time interferes with expeditious reclamation and since above grade storage of clays takes otherwise useful land out of production and raises potential health and safety problems, below grade storage and rapid reclamation techniques are encouraged." The two waste products from the beneficiation plant are clay slimes (-0.1 mm in size) and sand tailings. The sand tailings do not present a problem since the tailings rapidly dewater to a dry weight of about 100 pounds/ft3 and make good land fill. By contrast, disposal of waste clay slimes is a formidable task. The basic problem is simply that the waste clay not only dewaters very slowly, but also that the ultimate solids content is very low and in most cases the volume of the clay greatly exceeds the available volume of below ground storage of the mined land.

Jan 1, 1984

By G. A. Nyamekye

Two major Inco matte constituents, chalcocite and heazlewoodite, are separated by differential flotation with diphenylguanidine as collector. A new reagent system involving the use of dextrin as a modifying agent which provides better selectivity has been studied for the last three years. Adsorption tests reveal that while dextrin exhibits high affinity towards heazlewoodite, the adsorption isotherm for dextrin on chalcocite shows only weak interactions. Our electrokinetic measurements confirm such conclusions. Since dextrin interaction with solid surfaces seems to be especially strong when such surfaces are covered by hydroxide layer, our electrokinetic measurements are in line with other researchers' findings who postulated that copper hydroxide is not a stable product on the surface of copper sulphides.

Jan 1, 1992

By L. B. Gittinger

Mr, Chairman, members- and guests of the AIMS, I greatly appreciate this opportunity to speak before you. I hope this is just the beginning of a long and mutually beneficial relationship. This winter I decided to join the other 36 Freeporters who belong to the AIME; and, I applied for membership in the Society of Mining Engineers. To queries as to my interests in the Society, I had this answer: our principal challenge -- more so today, than at any time in my nearly 25 years in the industry -- is discovery and development of new sources of raw materials. I want to join you in meeting this challenge.

Jan 1, 1966

By Nikolaos Syrtariotis, Mark Berger, Timothy O’Brien, Vojtech Gall

The Northeast Corridor Superconducting Maglev Project (SCMAGLEV) entails construction of a high-speed train system between Washington, DC and New York City, with the first leg between Washington and Baltimore, MD. This innovative project will shorten travel times between Washington DC and Baltimore to approximately 15 minutes, and connect Washington, DC to New York City in under an hour. In 2021 the draft EIS is expected to be issued for comment with a Final EIS/ROD anticipated by early 2022. This paper provides an update on the project as presented in Gall et al. (2020) and discusses the economic and environmental benefits, preferred alignment alternative, preliminary staging and launching of the TBMs for construction, and preliminary station design.

Jun 13, 2021

By S. Tuylu, D. Adiguzel, A. Bascetin

"In recent years the fact that mining tailings cause serious environmental problems resulted in increasing number of studies about their disposal, storage and usability in various areas. Therefore the new studies about using the tailings for some purposes such as using in shotcrete or producing concrete have been increasing recently. The study is focused on applicability of tailings for producing shotcrete. Under this scope it is considered that mining tailings can bring many advantages in case of that they are used instead of sand, silt or fine aggregate in shotcrete applications. Most important advantages can be listed as decreasing shotcrete cost, decreasing amount if mining tailings to be disposed and the contribution to be provided on sustainable production of sources. The main objective of this study is the investigation of using mine tailing instead of fine aggregate in shotcrete. In this study, 10 shotcrete designs in different proportions were formed, and properties of the mixtures were identified. Then, the experimental results were statistically analyzed, the effects of the amount of the tailing material used on shotcrete properties were presented, and empirical approaches that can be used for the estimation of these properties were developed. INTRODUCTION The disposal of high amount mine tailing on the surface is caused a lot of problems in terms of environmental impact. Unfortunately, it is known that classic disposal techniques such as tailing dam cannot provide a solution these problems. The tailing dams which are usually used in the disposal of mining tailings bring along many problems in terms of cost, environment, and human health. So mine tailings are used in different production such as shotcrete. This technique is becoming increasingly common during recent years. The usability of mine tailings in brick and concrete production instead of cement and fine aggregate has been studied by many studies [1-4]. This situation has been promising for the usability of tailings in shotcrete which is commonly used for ground support especially in tunnels. Shotcrete (sprayed concrete) is applied mainly for construction of tunnels, shafts, renovation works and strengthening of slopes. Main advantage of shotcrete is fast development of strength, which quickly ensures stability of strengthened structure [5]. Shotcrete can be defined as spraying the grout consisting of water, aggregate, cement and optional additive mixture on the desired surface with a compressed air. According to the definition of the American Concrete Institute (ACI), it is the spraying of sprayed grout or concrete on a surface at high speed with air pressure [6]. In recent years, the use of shotcrete for the support of underground excavations is decreased in the mining industry. The design of shotcrete support for underground excavations is a very imprecise process. Strength and pumpability properties of shotcrete are very significant for determining suitable shotcrete design. Flow characteristics of the shotcrete must be determined for pumpability and fluidity of the material."

Jan 1, 2017

By Jorge Alberto Soares Tenório, Denise Crocce Romano Espinosa, Amilton Barbosa Botelho Junior

A new step in the Bayer process has been used to recover NaOH and to reduce its content in red mud. After digestion, the residue is separated from the Bayer liquor and goes through press filters, which enables the recovery of NaOH and decreases the moisture content. It is well known that red mud is one of the most important sources of scandium. For this reason, the goal of this work was to characterize a Brazilian red mud (BRM) for scandium recovery. The sample was collected after the press filter system process. Analysis of energy-dispersive X-ray fluorescence (EDXRF), scanning electron microscopy/energy-dispersive X-ray spectroscopy (SEM/EDS), and X-ray diffraction (XRD) was performed. Microwave digestion using an acid mixture was carried out to determine the concentration of the main elements. Fe2O3 represented 40% of the BRM, and the Sc concentration was 43 mg/kg. The SiO2 content was 24%, which is the highest value found in the literature, whereas the sodium concentration was the lowest. A literature review was carried out to compare results with BRM, as well as the current studies for recovery of scandium by the leaching/ion-exchange process. Scandium recovery using a leaching/ion exchange process may be possible with efficiency higher than 90%. The greatest challenge is the occurrence of silica gel formation during leaching.

Oct 19, 2020

By Praterm J. D.

The process parameters for effective utilization of nitric acid as an oxidant for copper-iron sulfides have been developed. Leaching variables found to be important were acid concentration, temperature, time, atmosphere, pressure, mineral type, particle size, and percent solids. Particular attention was devoted to analysis and control of fumes evolved during the oxidation. Responses recorded were metal extraction, elemental sulfur formation and oxidation, product gas composition and evolution rate, reagent consumption, and residue flotation response. The paper concludes by laboratory testing a flow sheet based on the above observations. Ninety-eight percent of the copper contained in a chalcopyrite-bornite concentrate was recovered, requiring 1. 6 pounds of nitric acid to be regenerated externally per pound of copper extracted. Iron remained in the leach residue as hydrogen jarosite and was ultimately rejected from the system by froth flotation. Sixty percent of the sulfur contained, in the heading concentrate reported in the elemental form; the remainder was oxidized to sulfate and eliminated with the hydrogen jarosite in the flotation tails or by neutralization of the solvent extraction raffinate with lime. Nitrogen was evolved primarily as NO and NO2; up to 3 percent N2O was also present. Gases containing sulfur were absent except when pyrrhotite was solubilized in the absence of soluble copper. In this case, H2S was evolved.

Jan 1, 1972

By Elimame Elaloui, Kais Elghniji, Constantin Virlan, Aurel Pui, Chaima Ouled Amor

Separation and identification of minerals composing the Tunisian silica sands have been conducted by acid etching and hot filtration/sedimentation (HFS) without affecting the quartz component. It was found that the hot acid etching process is an effective method to separate quartz and clay minerals in the silica sand. The SEM micrographs of the silica sand show rough surface and some cracks with irregular shapes. The surface becomes clean and smooth after acid etching process. After chemical dissolution, the clay minerals were recovered by hot filtration following by sedimentation at low temperature. FT-IR, EDS maps, and secondary electron (SE) analyses of separated clay minerals reveal the presence of Fe2O3, montmorillonite, and kaolinite minerals. The LIBS analysis of clay minerals shows the presence of Al, Fe, Ca, Al, and Mg. The sequential etching process can be introduced in the purification methods as an effective way to separate quartz from clay minerals.

Jul 29, 2020

By L. Alagha, F. Schott, M. B. Haya, Z. Xiao, K. C. Monyake

"Froth flotation is a process in which valuable minerals are separated from gangue minerals on the basis of surface wettabilities. It is a universally accepted process for the beneficiation of coal. The large amount of coal fines that have been generated from both mining and beneficiation processes has been reported as a chronic problem to both fine coal preparation and utilization as these fines contain a high amount of ash forming minerals. The current study investigated the potential application of Synthetic Bio-compatible Polymers as slime depressants in fine coal flotation for the possibility to enhance the combustible recovery and ash rejection. Raw coal samples containing 21% of ash-forming minerals were crushed, grinded and floated in the presence of Chitosan polymer. Flotation tests were carried out in D-12 Denver flotation cell with 1-Liter capacity. Flotation outcomes were studied as a function of polymer concentration. Box-Behnken factorial method was used for experimental design. Second order response functions were produced for ash% and combustible recovery. The results obtained from this study demonstrated positive influence of chitosan polymer on ash% and combustible recovery. Ash % was decreased by 3.32 % while an increase of 48.15 % in combustible recovery was observed when chitosan was introduced in the flotation process. INTRODUCTION Froth flotation is a widely used method of separating minerals by utilizing the difference between surface wettabilities [1], [2].Modern mechanized mining and ore handling operations produce large amounts of coal fines which in the past were not processed but discarded as waste[3]. Even though flotation is the best method of beneficiation for coal, it can be challenging in case of fine coals. In fine coals, slime coatings of colloidal mineral matter exist on the coal surface. These coatings render the coal hydrophilic, hence reducing flotation efficiency and recovery. Of late, different researches have been using biodegradable polymers to determine their feasibility in enhancing fine coal flotation efficiency[4].Naturally occurring and synthetic polymers, for example, polyacrylamide-based polymers, have been widely used in flotation as multifunctional reagents[5],[6],[7]. Hybrid polyacrylamide polymer has been successfully used as a depressant for ash forming minerals in fine coal flotation[3]. Recently, chitosan has been successfully used in flocculating quartz particles to produce faster settling rates of fine tailings [4]."

Jan 1, 2018

By Barbara J. Arnold

The Electric Power Research Institute (EPRI) and six EPRI-member utilities are sponsoring research to define relationships between coal properties and coal handling behavior. Deratings and outages caused by plugged chutes or bunkers or frozen coal can cost utilities millions of dollars annually in lost energy production as well as in manpower to restore coal flow. There is also the added expense of maintaining redundant equipment to assure a continuous coal feed to the boiler, a common practice for utilities. Over the past two years, researchers at CQ Inc. and Iowa state university have collected and analyzed coal samples to develop a coal handleability index for utilities to use when specifying coals for their power plants. These coal samples cover ranges in ash content, rank, grindability, size distribution, and moisture content--properties that affect the handling behavior of coals. Other properties, such as the washability and ash composition, are measured as well. Over the remaining two years of the project, all of these analyses will be correlated to handling behavior, measured using a triaxial shear tester that determines the strength of a coal under compression. An index will be developed and validated at host utility power plants.

Jan 1, 1991

By G. F. Revey

Most commercial explosives contain 70 to 94% ammonium nitrate, by weight. When portions of these explosives end up in shot rock and ore, through spillage or incomplete detonation, ammonia and nitrates leach out of them and into ground water. In recent years, State and Federal regulators have been applying more stringent water quality standards, particularly at new mines and development projects. Bulk ANFO, a mixture of ammonium nitrate and fuel oil, is the explosive of choice at most mines, when mining conditions allow it. ANFO use is desired because it less costly than other explosives, but when spilled it dissolves readily in water. Several case histories in the United States and Canada show a clear connection between uncontrolled losses of bulk explosives and high nitrate levels in mine effluents. Mining companies have tried several approaches to reduce ammonia and nitrate levels in groundwater. They either control explosive losses, or they treat mine effluents at the end-of-pipe. This paper addresses the former solution --controlling explosive losses. For both packaged and bulk explosives, guidelines designed to limit losses during storage, handling and use, are described in detail.

Jan 1, 1995

By H. M. Castrantas

Caro's (peroxymonosulfuric) acid has been reported to destroy WAD (weakly acid dissociable) CN-but, until recently, the technology has not been demonstrated in other than a laboratory setting. During the last two years, Caro's acid has been shown to successfully detoxify WAD CN-in tailings at two large North American gold mines. Using on-site FMC generators, Caro's acid reduced the WAD CN-from 40-55 ppm to below 20-35 ppm WAD CN-, the target range for the two mines. The detoxification costs using Caro's acid were less than 50% of the treatment cost of using hydrogen peroxide, the previous oxidant of choice. In addition to the considerable savings in CN-detoxification costs, lower WAD CN-values were achieved and the detoxification time with Caro's acid was greatly reduced compared to hydrogen peroxide.

Jan 1, 1995