Search Documents

By Ben Benally, Joseph M. Hans

INTRODUCTION The decontamination of the former Shiprock uranium millsite and the interim stabilization of its tailings piles began in March 1974, and ended in June 1978. Personnel monitoring for whole body gamma ray exposure was conducted for selected individuals working at the mill site throughout most of this period. The millsite and exposure conditions are briefly described to develop a basis for interpretation of the exposure data. Millsite The Shiprock uranium millsite is located in the community of Shiprock, New Mexico on a bench overlooking the San Juan River (Figure 1). Both Shiprock and the millsite are located on the Navajo Indian Reservation. About 1.5 million tons of tailings were produced on the millsite during its operation from 1954 to 1963. The tailings were pulped with waste process fluids and water, and discharged to form two tailings piles. The piles (ponds, dams) were formed with earth starter dikes and the dikes were then raised using the separated sand fraction of the tailings. The slime fraction of the tailings were discharged into the diked impoundment. The mill was shut down and partially dismantled before the lease expired in 1973, and the remainder of the mill and tailings reverted back to the Navajo Tribe which was the lessor. Portions of the millsite were then occupied by the Navajo Engineering and Construction Authority (NECA), a tribal enterprise. In addition to its regular activities, NECA established an on-site training school for heavy equipment operators. The trainees principally used the south tailings pile as a practice area and spread the tailings into a 10 hectare row of raffinate ponds located along the southwest side of the millsite. Overall, the training activities inceased the effective area of the tailings piles from 20 to 35 hectares. Another 56 hectares were contaminated with wind and water eroded tailings. Exposure Conditions Persons decontaminating a millsite may be subject to radiation exposures from several sources. Only whole body gamma exposures are discussed in this report. These exposures are arbitrarily divided into three levels: high, intermediate, and low. The levels are related to areas in which the decontamination work was being done and have no connotation concerning imminent hazards. High exposures would result when persons were working with raw tailings, and intermediate exposures would occur when persons were working in the ore storage and mill yards. Low exposures would result from working in areas where surface contamination exists from wind and water erosion. [ ] The millsite and its contaminated environs were divided into major areas to facilitate the decontamination work (Figure 2). Areas A, B, and C are defined as perimeter areas containing surface contamination. Work in these areas was expected to result in low exposures. Areas D, E, and F are the

Jan 1, 1981

By Onur Golbası, Berk Gokce

Investment decisions in the mining industry are complicated by sector-specific uncertainties. This study presents a multi-submodule system dynamics model to capture the dynamic complexities of decision-making across mineral property development stages. The model includes five interconnected subsystems: valuation, production, growth strategy, demand, and finance. Developed through system decomposition, expert input, and literature, the model is tested on a hypothetical copper mine with 850 ktpa capacity and 1% cu grade. Simulated over five years with quarterly steps, it estimates an enterprise value of $78.9 million and a target growth rate of 11.2%. Results highlight the significant effects of operating costs, capital policies, and inflation on free cash flow, and the critical role of mineral reserves in sustaining growth. This model supports strategic investment analysis across different minerals and development phases, offering mining investors a robust tool for optimizing decisions.

Feb 22, 2026

By D. Tepavac, S. Simmonds

"The high virgin horizontal in situ stress field in the Sydney Basin and its impact on civil engineering projects is a well-known and accepted phenomenon found in significant literature (e.g., Pells, 2013). The prevailing high-stress effects depend on many factors — rock quality, tunnel orientation, proximity of geological features to tunnel crown, size and shape of opening, depth of excavation and stress magnitude. The behavior of the rock mass under high in situ stress conditions can cause stress fracturing and consequent dilation of the tunnel periphery, resulting in rock spalling at the tunnel crown/ invert or raveling of rock blocks on the tunnel sidewall. This type of failure is of a brittle nature and may create construction and safety risks during tunnel excavation, if it occurs behind the excavation face where ground support has already been installed. Therefore, the associated risks need to be managed during construction. This paper presents the design strategy adopted to mitigate these adverse tunneling conditions for the WestConnex Project to-date. Overview of the WestConnex M4 East and new M5 tunnel projectsWestConnex is one of the New South Wales government’s key infrastructure projects. This 33 km (20.5 mile) project aims to ease congestion and connect communities and is the largest integrated transport and urban revitalization project in Australia. It was a key recommendation of the State Infrastructure Strategy released in October 2012. It brings together a number of important road projects, which, together, form a vital link in Sydney’s Orbital Network. These road projects include a widening of the M4 east of Parramatta, a duplication of the M5 East, and new sections of motorway to provide a connection between these two key corridors. The WestConnex project includes a number of stages: Stage 1a: M4 Widening; Stage 1b: M4 East; Stage 2: New M5; and Stage 3: M4–M5 Link. The tunnel design referenced in this paper relates to Stage 1b and Stage 2 of the WestConnex Project (Fig. 1)."

Dec 1, 2018

By David E. Lindorff

The impact of surface coal mining on the geologic materials and ground water in different geologic settings is being investigated by the Illinois State. Geological Survey at three abandoned surface mines in Illinois. At a site near Ottawa in La Salle County, the overburden prior to mining consisted largely of pyritic shale; sand was the major component of the overburden and spoil at a mine near Coal City, Grundy County. Clays, lacustrine silts, and some shale and limestone were the dominant premining overburden materials at a mine near Harrisburg, in Saline County. Ground-water elevations at Coal City and Harrisburg are approximately at premining levels, whereas at Ottawa they are near the base of the spoil. Ground-water quality has deteriorated at all three sites, especially at Ottawa and Harrisburg.

Jan 1, 1981

By W. P. Blacutt

A financial-economic model incorporating physical, market, and policy variables is developed for mining investment in Bolivia. Additional risk criteria emanating from political instability. new mining legislation, recent environmental regulations, and a new minerals taxation system are accounted for and are integrated into the investment decision model. Results of the model indicate that geologic and market variables have the dominant effect on the investment-worth function. Among policy variables, exchange rate and taxation policies have the most significant influence. Depreciation allowance for infrastructure development has negligible weight in the investment-worth function. The business structure of the firm considering investing in the Bolivian Polymetallic Project is found to be an instrumental factor in the investment-worth outcome. Specifically, undiversified mining companies whose operations exclude zinc production as the primary source of revenue would benefit most from adoption of this project.

Jan 1, 1993

By P. Dhar, H. R. Kota, M. Thornhill

A very high-grade calcite deposit located in northern Norway consists of CaCO3 ore with minor silicate and sulphide impurities. Cationic (Tallow-1,3-diaminopropane, Duomeen T) collector has been used in the purification of calcite by flotation with an aim of achieving calcite concentrate for its use in value-added products in a variety of industries. The feasibility of sulphide flotation from calcite by this cationic collector has been initially judged from Hallimond flotation and zeta potential on pure mineral systems and the results illustrate the removal of sulphide from calcite ore at neutral pH region. The adsorption mechanism of diamine on both the sulphide minerals was found to be the same by zeta potential studies. The variations in zeta potential are in good agreement with the adsorption of diamine molecular and ionic species as a function of pH. FTIR studies also showed the adsorption of diamine species in agreement with the zeta potential and Hallimond flotation results. Furthermore, the removal of sulphide impurities with selective flotation by diamine collector was performed in bench-scale flotation with the calcite ore and the results indeed showed that the calcite concentrate could meet the quality requirements for its use in the paper industry for coating and filler purposes.

By Atta Ur Rehman, Kwame Awuah-Offei

This paper examines the effect of bucket geometry (cutting-blade profile, floor profile and blade thickness), speed, motor power output and muckpile particle sizes on bucket penetration and draft for rubber tire loaders. The work uses a 1:16 scale model of a load-haul-dump (LHD) in full-factorial experiments to examine the effect of the variables on penetration and maximum draft. The results show that speed and motor output are positively correlated with penetration and draft, and muckpile particle size is positively correlated with penetration and negatively correlated with draft (p < 0.0014).

By J. M. King

A crucial step in the acquisition by one company of the assets of another, the acquisition of the stock of another company, or the merger of two com-ponies, is the legal due diligence which needs to be performed in order for the acquirer to ascertain or confirm the obligations, liabilities and exposures to risk that are being assumed along with the assets or corporate stock being acquired. Where the obligations, liabilities, or exposures to risk arise from existing contracts, or from pending lawsuits, administrative proceedings, or threats of these actions, those matters are relatively straightforward to discover by careful review of the files of the party whose assets or stock is being acquired. However, where a company is engaged in ongoing mining or processing operations and has operated or owned mining proper-. ties, there are many sources of liability and exposure to risk which could have major adverse economic consequences to the acquiring party and which are not revealed, or at least are not clearly delineated, by the records of the company whose stock or assets are being acquired.

Jan 1, 1990

By Haydn H. Murray

Although alumina constitutes about ii percent of the earth&apos;s crust, it is expensive to separate and purify for the production of aluminum with the exception off the alumina in bauxite. The United states has a variety of non-bauxite resources that could substitute for bauxite, including high alumina clays, alunite, dawsonite in oil shale, anorthosite, and nepheline syenite. Each of these resources are discussed from the standpoint of geology, geography, processing, potential recovery, and environmental problems. Potential by-products include silica from clays, potash and sulfuric acid from alunite, soda ash from dawsonite, and soda ash and potash from anorthosite and nepheline syenite.

Jan 1, 1982

By Steven E. Paulson

In situ mining is emerging as a potential alternative to conventional surf ace and underground mining techniques. A major factor in determining recoveries by in situ mining is the proportion of ore minerals that can be contacted and solubilized by the leach solutions. To provide basic information on the processes occurring during in situ leaching, particularly at the microscopic scale, the Bureau of Mines has developed a geologic characterization research program. This includes laboratory experiments using leaching apparatus that can accommodate whole core samples. Whole core experiments result in higher leach solution-ore mineral contact ratios than packed column experiments, and also allow for the assessment of permeability changes taking place as the result of mineral dissolution, precipitation, and clay swelling within the flow channels in the rock. A nonreactive, reusable reaction cell has been designed and tested. The leaching apparatus can be used for constant-pressure or constant-flow experiments and allows for the control of flow rate, pressure, and temperature during the experiments, thus permitting studies on a wide variety of ore samples. Details of the experimental apparatus and design are presented, as well as preliminary results from the first series of experiments on an oxide copper ore from the Casa Grande, AZ, area.

Jan 1, 1987

By E. C. Winegartner

In producing and selling coal, the coal company is faced with many different parameters by which the quality of its product is evaluated. One type, which we choose to call the economic parameters, includes moisture, ash, sulfur, and Btu&apos;s. These are reasonably well understood by both the coal supplier and the customer, and the dollar values can be placed on them. This is the group of parameters of primary interest to most purchasing agents buying coal. A second group of parameters governs how the coal will behave in the boiler itself and is of primary concern to the engineers designing the boiler and to the men who must operate and maintain it. Since we have not yet learned to put dollar values on these parameters, they generally show up in coal contracts simply as cutoff points, the purchaser simply saying that he will not accept coal outside of certain limits.

Jan 1, 1975

By R. Gray, B. Hebblewhite

Experience from Australia had identified what is referred to as nonconventional surface subsidence behavior. This occurs under irregular surface topography, resulting in valley closure, valley floor uplift or “upsidence,” and far-field horizontal movements, occurring even beyond conventional “angle of draw” limits. This paper discusses such behavior recently observed in Pennsylvania and focuses on the 2005 case of Duke Lake Dam in Ryerson Station State Park. In July 2005, there was a significant increase in water leakage through a number of growing cracks in the dam, leading to the dam being breached to avoid an uncontrolled failure. An underground longwall mine was located approximately 900 ft to the north, mining at depths of 330 to 720 ft. Investigations, including a subsequent ground movement monitoring program, found a range of evidence in the vicinity suggesting that valley closure and farfield horizontal movements may have occurred, resulting from the adjacent mining. Besides discussing the phenomenon of nonconventional subsidence behavior and the Ryerson State Park case study, this paper includes an assessment of the mining, geology and subsidence impacts and suggested ground behavioral mechanisms.

Jan 1, 2015

By D. C. McLean

Early studies in the carbonate leaching of uranium ores led to the investigation of pressure leaching as a method to enhance the dissolution of the metal values in this system. The initial investigations conducted at the University of British Columbia supplemented by the work done by the group at the A.E.C. Grand Junction pilot plant, all established the higher efficiency and better economics of the alkaline pressure leaching system. This work was conducted either in laboratory autoclaves using oxygen overpressures, or in pilot plant sized horizontal autoclaves with air as an oxidant. Both of these testing vehicles utilized agitation provided by relatively high speed impellers (300 to 700 rpm), which apparently enhanced the oxidation of the uranium to the hexavalent state. The installation of vertical autoclaves on a production scale, which through design considerations require relatively slow agitator speeds (68 rpm), led to the studies of the utilization efficiency of the air addition and the use of catalytic type oxidants to effect a greater usage of the oxygen added through the aeration system. In addition to investigating the effects of the chemical additives, studies were also conducted on the effect of different impeller configurations on the extraction of uranium, which in itself is a measure of oxidation efficiency. The material presented in this paper was compiled in the Ambrosia Lake district of New Mexico, and the majority of the data was obtained in the Homestake- Sapin Partners mill, located at Grants, New Mexico.

Jan 1, 1960

By B. A. Barnum

The Chino mine is an open pit copper mine located in southwestern New Mexico, at an elevation of 1890 m (6200 feet) above sea level, approximately 117 km (70 miles) north of the Mexican border. It is owned by Chino Mines Co., a Phelps Dodge Corporation-Mitsubishi Minerals partnership, and is operated by Phelps Dodge Corporation. As part of an effort to maximize production and minimize costs, a computerized truck dispatching system was approved for purchase and installation at the Chino mine in March. 1984. Modular Mining Systems, Inc. was commissioned to install their system, trade named DISPATCH. The system installation was completed and operation began in July, 1985. Installation and operation of the system has presented some interesting challenges and problems, which have been overcome, resulting in increased productivity for the haulage truck and shovel fleets.

Jan 1, 1987

By M. R. Shahan, W. R. Reed, P. Zhang, J. P. Rider

Roof bolter operators may be exposed to high respirable dust concentrations on continuous miner sections with blowing face ventilation when bolting is performed downwind of the continuous miner. One solution to reduce the high respirable dust concentrations is to use a canopy air curtain (CAC) to deliver clean air from a filtered blower fan directly to the bolter operators under the canopies. The influence of CAC installation in the airflow and dust dispersion around the location of the roof bolter operator can be evaluated by using computational fluid dynamics (CFD). This study, performed by the National Institute for Occupational Safety and Health (NIOSH), considers two scenarios: (1) a roof bolting machine in the center of the entry for installation of the fifth row of bolts from the face, and (2) a roof bolting machine positioned close to the face for the installation of the last row of bolts. In both scenarios, the bolting machine is placed in an environment which contains 6.0 mg/m3 of respirable dust and is ventilated by a blowing curtain with 3,000 cfm (1.42 m3/s) of air. This environment is used to simulate the roof bolter machine operating downstream of a continuous mining machine. Two operation positions are simulated at the same bolting location: dual drill heads in the inward position for two inside bolts; and dual drill heads in the outward position for two outside bolts. The influence of the CAC on airflows and dust dispersion is evaluated with the CAC operating at 250 cfm (0.12 m3/s). INTRODUCTION Roof bolting machines are used to drill bolt holes into the roof of an underground mine at specified patterns and to install roof bolts to secure the roof from falling. At times, the roof bolting machine is also used to install rib bolts; however, only the roof bolting operation was considered in this simulation. Though the roof bolting operation drastically improved the safety of miners from roof falls, some roof bolter operators are experiencing health problems associated with respirable dust. Based on recent statistics [1], following a low point in the late 1990s where the prevalence of coal workers’ pneumoconiosis (CWP) in miners with 25 years or more tenure was approximately 5%, CWP now exceeds 10% for miners with 25 years or more of tenure. In central Appalachia (Kentucky, Virginia, West Virginia), 20.6% of long-tenured miners have CWP and 4.5% have progressive massive fibrosis, the most severe form of CWP. CWP, also known as black lung, is an occupational respiratory disease that has no cure and can ultimately be fatal. The only way to prevent the incidence of black lung is to eliminate miners’ exposure to respirable coal mine dust. Current U.S. regulations require that the overall respirable dust concentration to be 1.5 mg/m3 or less for a full-shift sampling if respirable quartz is not present; otherwise, the standard is 10 divided by the percent quartz (not to exceed the 1.5 mg/m3 respirable dust standard) [2, 3].

Jan 1, 2019

By Jerry C. Tien

The rare earth elements (REEs) are a group of 17 chemical (metallic) elements which appear in the periodic table. The group consists of 15 lanthanide elements along with yttrium and scandium (Table 1). They share many similar properties, which is why they occur together in geological deposits. Although commonly referred to as rare, they are really quite common; the reason they are perceived as rare is because it is not common to find them in commercially viable concentrations. These metals are critical to advanced technology, ranging from smart phones to global positions system (GPS) receivers, medical devices and jet engines. They are critical in green, high-tech and defense industries (Fig.1 and 2). Although there have been increasing efforts to find alternative supplies, these efforts have been complicated by the pollution that rare earth mining and processing creates. To extract rare earths minerals from mined ore is a complicated and costly process. The ore is first mined through normal mining process, the bastnaesite, which generally contains a number of minerals of little value, is first removed through a floatation process. The bastnaesite containing the REEs is further separated into their respective pure forms in a separation plant using acid and various solvent extraction separation steps. Each element has its own unique extraction steps and chemical processes. At times, these elements, in the form of oxides, will require reprocessing to achieve ideal purity. The last steps would be to further process into metals first, then alloys for various applications. The entire process takes approximately 10 days. The mining and processing of REEs, if not carefully controlled, can create environmental hazards. This is one of the reasons the Mountain Pass Mine in California was closed down in the 1980s.

Dec 1, 2013

By Cody Giroux, Homer Scurlock, Michel Wasag

Silica and Crystalline Quartz exposure continues to be a serious health threat to nearly 2 million workers in the United States, including more than 100,000 working in high risk jobs such as abrasive blasting, foundry work, stonecutting, rock drilling, quarry work, mining and tunneling. The primary focus of this study is to identify the best methodology to reduce particulate-laden air and limit/eliminate exposure to respirable dust with silica/crystalline quartz during tunneling operations. This study focuses on two de-dusting systems employed on similar tunnel construction projects. The first project is the Coxwell Bypass Tunnel located in Toronto, Ontario Canada. The second project is the Westerly Storage Tunnel located in Cleveland, Ohio. The Toronto project is utilizing a wet de-dusting system. The Cleveland project is using a dry de-dusting system. The objective is to determine which system provides the best protection and suitability to capture, remove and ultimately reduce respirable concentrations of silica/ crystalline quartz to safety and healthy levels in underground tunneling activities.

Jun 13, 2021

By Leping Liu, Sachin Urade, Li-Ting Chen, Pengbo Chu

This study aims to provide industrial perspectives on the current U.S. metal mining engineering education and areas for improvement. An online survey was designed to seek opinions from the U.S. mining industry. Findings indicated a shortage of qualified graduates from the current U.S. metal mining engineering education system. The qualifications that need to be improved include engineering sciences underlying mining methods, mining design experience, mining feasibility study, the connection between theory and practice, and understanding of the overall mining operation. The survey also identified future desired qualifications, such as the ability to acquire and apply new knowledge as needed and sufficient field experience. Respondents recommended enhancing collaborations between industry and academia.

Oct 1, 2023

By Peter J. King

Demand for both lead and zinc to the year 2000 will be characterised by modest to nil growth in mature economies, with positive 3 to 4 per cent annual growth rates in developing nations. Asia and China will feature significantly in this growth. Overall lead demand is expected to grow about 1 per cent a year, with industry becoming more dependent on the fortunes of the automotive industry as the lead-acid battery will be the only major end use to expand. Zinc will become more dependent on its main use, galvanising, as the automotive and construction industries move to high levels of dependence on corrosion prevention. Strong growth in zinc consumption in S.E. Asia, China and India is likely to feature widespread development of the continuous steel strip mini-galvanising line technology. Thank you Mr. Chairman for inviting me to this Conference. As an Australian I am honoured to be here to offer some thoughts about future trends in metal consumption -- with particular reference to the role of countries in my own neighbourhood, the developing Asian nations, including China. It is customary for a member of the producer fraternity to speak to the topic of future development. This is no doubt due to the fact that our companies are so often engaged in endeavours to determine the future prospects of the metals as essential background to massive investment decisions relating to the development of new mines and smelters. This is sometimes also applied in relation to the more painful decision of closures of aging operations. In this paper I have drawn upon recent studies by AM&S into the future of lead and zinc. While this work has been thorough and skillful, we are nonetheless left with uncertainty on a number of counts. Firstly. predictions in the past in our industry have not been all that credible. Need I remind a U.S. audience for instance of the Paley &apos; investigation setup by President Truman in 1950 to study U.S. copper requirements for 25 years in the future. Asarco&apos;s Simon Strauss gave those of us daring to forecast long term commodity trends a salutary reminder that the Paley Commission with all the expertise at its disposal missed the mark in its copper predictions by a very wide margin indeed. Additionally, it is difficult to take comfort from longer term economic forecasts. Too many important economic issues remain unresolved suggesting considerable caution. These include the threat of growing protectionism; low economic growth rates with stubborn unemployment levels; and levels of government expenditure at near saturation as a percentage of GDP, to name a few. However, on a more optimistic note. we can look to China, where there appears to be momentum in its economic growth; oil, where stable oil prices to the mid 1990&apos;s will contribute to inflation control; and the fact that LDC debt, while still a major issue, is declining in importance and priority. In the short time allocated to us. I wish to deal succinctly with the lead and zinc raw materials supply picture, which is one I do not believe will hold too many surprises for this audience. Following the review of raw materials supply, we will turn our attention to the changes in the pattern of demand towards the year 2000. emphasising the Asian position. In this context. I would like to focus on the theme of the changes in OECD consumption levels relative to those of the emerging nations. One area we will be paying special attention to is China.

Jan 1, 1986

By Duk-Wom Park

INTRODUCTION he most important information required for the engineering design of structures in rock is its inherent rock properties. Without providing adequate parameters on the rock property, high quality of the engineering design cannot be expected. Many laboratory rock testing methods have been developed, but they are mostly for testing intact homogeneous rock without appreciable discontinuities. In reality, the intact rock properties do not represent the behavior of rock masses because rock masses include irregularities such as joints, cracks, interlayers, variations in mineral compositjon, etc. In general the type and intensity of the rock defects may be much more important than the type of rock which will be encountered (Terzaghi, 1977; Bieniawski, 1984). In-situ rock testing can provide better information on rock parameters, but it takes a tremendous amount of effort, time and cost. In recent years, numerical modeling techniques are gaining popularity as a design tool for structures in rock bodies due to the enormous progress in computer technology (Wang, 1985; Kripakov and Melvin, 1983; Park and Ash, 1985), but it is quite dangerous to use numerical techniques without having proper input data. Bieniawski (1984) states as follows: Some design methods such as numerical techniques have outpaced our ability to provide the input data necessary for the application of these methods. In order to provide an adequate amount of input data, an extensive testing program may be required, thus major efforts in time and expenses are commonly spent, In this paper, a new rock testing method, which utilizes the principles of laser holographic interferometry, is introduced. This method requires only a few minutes to measure the modulus of elasticity and quality of a rock core sample, which does not have to be cut or ground. The Poisson&apos;s ratio can also be measured in a few minutes from a sliced rock specimen. HOLOGRAPHIC INTERFEROMETRY Principles of Holographic Interferometry In 1948, Gabor invented holography, which is the technique of reviving three dimensional images using a monochromatic light source. A full demonstration was not made then because a clean monochromatic light source was not available. Later, in the early 19601s, the laser was adopted as a monochromatic and coherent light source (Leith and Upatnieks, 1963). Since then, applications have been made in many different fields ranging from crime prevention to three dimensional television. In this technique, an image is usually recorded by means of constructing a hologram which is a record of the interference pattern formed on a high resolution photographic system as shown in Figure I. A beam splitter divides the laser beam into two beams: (1) an object beam which is expanded while passing through a beam expander and illuminates the object, and (2) a reference beam which is expanded and illuminates the holographic plate. Subsequent to an exposure, the holographic plate is developed and illuminated by the expanded reference beam. The original scene of the object is revived in a three-dimensional image. The entire instrument should be placed on a vibration free environment. The wave fields reflected by the object in two slightly different configurations can be superimposed to form an interference fringe pattern. Thus, it is possible to measure the displacement that took place between the two configurations. This method is called holographic interferometrv. There are two methods of achieving this phenomena. The first is the double exposure method, wherein two exposures of the object are made prior to developing the film. The first exposure represents the original condition and the second, the disturbed condition. The second method is the real time holographic method. In

Jan 1, 1986