Search Documents

By M. McPherson, G. Danko

Methods of measuring in situ rock thermo-physical properties are rapidly evolving. Among those existing in the literature, a particular measurement procedure was selected for further development. The measurement is based on creating a spherical temperature field in a drill hole using a point source heater of constant heat flux. The bivariate temperature distribution 0 (r, t) is measured at several points along the length of the drillhole, radius r from the heater and at particular time intervals (t). A number of different evaluation methods were tested for calculating the unknown thermal conductivity (k) and diffusivity [] from the measured temperature and the known heat flux. The results showed that evaluation using the finite difference scheme and small temperature differences measured at points close together, cannot give a reasonable result. In order to solve the problem a new general analytical evaluation method is developed. Using an appropriate technique, it is possible to simultaneously obtain values for k and [], incorporating a semi least square technique to reduce the uncertainty in the evaluation. The new device and evaluation method makes it possible to obtain from a single drill hole highly precise k and [] values within an 8 hour period. The method has been used in several underground mines in the U.S. with good results.

Jan 1, 1987

By R. F. Kovar, R. N. Torbin, R. E. Gundersen

I have to express my .surprise and must send a note of warning concerning the use of polyurethane foam as described in a paper by R.N. Torbin and R.F. Kovar, entitled "Innovative Shaft Lining Method," published in your February 1989 edition. In September, 1986, 177 miners lost their lives when they were exposed to fumes downwind from a fire in a tunnel lined with polyurethane foam. Whilst polyurethane exhibits reasonable fire retardent properties in small-scale tests, mass use in a tubular configuration, exacerbated by the furnace effect of cross-radiation, can lead to a rapid, uncontrollable conflagration. I do not wish these comments to detract from the engineering achievements of the authors but rather to sound a loud warning as to the application of the system. Any shaft designed for human access- be it for transport or shaft work - and any intake airway, should not consider the use of polyurethane foam. It only needs a slip with a cutting torch or an electric fault to initiate a disaster. Many countries have banned or restricted the use of polyurethane foam in the workings of a mine and maybe alternative foams (e.g. phenolics) can be used or developed

Jan 1, 1991

By Michael A. Redfearn

The use of nitrogen in molybdenite flotation circuits is a relatively new concept utilized by only a few mines around the world. This paper briefly discusses circuit chemistry and the reason for its success. It follows the entire testing process which resulted in a sodium hydro-sulphide dosage reduction from 18.5 to 4.4 lbs/ ton (9250 to 2200 g/t) through to the final installation of an inert gas generator which will produce reagent savings in excess of one million dollars annually. A description of the various types of nitrogen generators commercially available is included.

Jan 1, 1983

By Dayu Long, Changhong Li, Yu Wang, Juzhou Li, Yongyue Hu

To address the problem of seepage failure that affects the stability of the fine-grained tailings dam, two kinds of prevention and treatment measures were proposed involving composite flocculants and composite curing agents. The orthogonal test was conducted to determine the optimal ratio flocculant (ORF) and the optimal ratio curing agent (ORCG). Then, numerical models were established to evaluate the effects of the prevention and treatment measures on the seepage and stability of the tailings dam. The results show that the mechanical properties and microstructure of the tailings are significantly improved by adding the ORF and ORCG. Furthermore, numerical studies suggest that the addition of the ORF and the ORCG to the tailings improves the factor of safety of the tailings dam, but the addition of the ORCG also increases the height of the phreatic line. It is also speculated that the addition of the ORF can prevent the formation of through failure zone in the tailings dam. Therefore, the optimal measure to prevent seepage failure in the tailings dam is adding an appropriate amount of the ORF, as it reduces the height of the dam’s phreatic line and lowers the risk of seepage failure. The typical area susceptible to seepage failure can be treated by adding the ORCG. However, it is important to ensure adequate drainage of the area and to maintain the phreatic line at a reasonable buried depth.

Mar 4, 2024

By Jian Deng, Hehua Zhu, Lianyang Zhang

Rockburst is defined as a sudden and violent explosion of rock on the surface of a rock excavation. Rockburst has been regarded as the least understood and most feared hazard problem for underground rock excavations. Traditionally, rockbursts were classified into the strain, pillar, and fault-slip categories. However, rockbursts are also known to occur at stress levels well below the rock yield strength, in mines where the rock is far from brittle, or without the presence of geological discontinuities. A plausible explanation of rockbursts is buckling, which has been identified as one of the main mechanisms for rockbursts. It is observed that rockbursts are often induced by dynamic loadings (pulses) from adjacent blasting. Therefore, the present paper studies the effect of pulse shape and amplitude on pillar rockbursts induced by dynamic loadings from blasting using the method of numerical analysis. The governing equation of a pillar’s motion is set up and the mechanism of pillar rockbursts is investigated through a practical example. The results show that it is not the shape of a pulse but the impact energy to decide the occurrence of pillar rockbursts. If all other parameters remain the same, pillar rockbursts are more likely to occur when the pulse duration is longer. The parametric resonance and the perturbation of dynamic loadings are also found to play an important role in the occurrence of rockbursts. These insights would provide invaluable clues about the mechanism and for better control of pillar rockbursts.

Apr 26, 2022

By S. L. Bessinger

Introduction Extensive testing in the past ten years has shown that where a uniform natural gamma background is present in the strata bordering a seam, the thickness of the boundary coal left in place after mining can be determined by measuring the attenuation of that radiation (Nelson and Bessinger, 1989). Measurements made by the authors in underground mines in Pennsylvania, West Virginia, Ohio, Illinois and Kentucky and by others in Wyoming and New Mexico have shown the presence of such a gamma background (Nelson. 1989). Natural gamma coal-thickness sensors of several configurations have been tested in mines owned and operated by the Consolidation Coal Company (Consol) in Pennsylvania and West Virginia (Nelson and Bessinger, 1988). This paper describes the installation of a natural gamma coal-thickness sensor on an operating continuous miner. Previous tests had shown that the NGB-1000 coal-thickness sensor manufactured by American Mining Electronics, Inc., of Huntsville. AL, is an accurate, mine-worthy instrument. This large gamma detector consists of a sensing head and a control panel. The sensing head contains thallium-doped, sodium iodide scintillating crystal, which is coupled to a photomultiplier tube. The control panel contains the electronic components required for calibration, count conversion and display to the operator. Methods Conditions at a Consol mine in northern West Virginia require that 10 to 15 cm (4 to 6 in.) of coal be left at the roof boundary of continuous miner development sections. This roof coal is required because the shale of the immediate roof is friable and unstable. In the past, operators have used a dirt band that is usually visible near the top of the seam as a guide in maintaining the proper cutting horizon. However, this is not always reliable. Earlier observation showed that the actual thickness of the coal left on the roof varied widely; further, it was noted that occasional, accidental excursions into the immediate roof required supplementary roof control measures, such as installation of planks or center bolts. Thus, it was concluded that operators needed a better source of guidance for control of the cutting horizon, and a roof-coal thickness sensor was scheduled for installation. The NGB-1000 sensor was installed on a Joy 12CM10 continuous miner in June 1988. The sensing head was mounted on the cutter boom of the miner, and the control panel was mounted in the operator's cab. Power for the sensor was initially derived from an intrinsically safe battery power supply. Initial measurements with the sensor showed that the calibration was the same as that used in earlier tests at two other mines, indicating the uniformity of the natural gamma background above the Pittsburgh seam. Operating personnel were initially skeptical of the instrument's accuracy, and were hesitant to use its readings as a guide in maintaining a proper cutting horizon. Because gamma attenuation, the instrument's operating principle, is somewhat abstract, attempts to demonstrate the instrument's accuracy by explaining that principle were generally ineffective. It was found, however, that an operator could usually be convinced of the usefulness of the instrument by placing a large piece of coal of fairly uniform thickness over the instrument's sensing head and allowing the operator to see that the instrument reading increased by an amount very near his estimate of the thickness of the piece. The mine was provided with seven battery power supplies and a charging station. The charging station was kept in the lampman's office, and the mechanic on each shift was instructed that he was responsible for two battery power supplies each day: a freshly charged one to be taken in at the beginning of his shift and a depleted one to be brought out at the end. This system worked well for a few weeks, but eventually some battery power supplies were left in use so long that their batteries were discharged too deeply to allow recharging. In addition, transport and recharging of the batteries represented an additional task for the mechanics, who were already very busy. Consequently, a request was filed with MSHA to allow the sensor to be powered through intrinsic safety barriers by an electronic power supply connected to machine power. The permit was granted, and the sensor was connected to machine power. After the sensor was connected to machine power, the only operating problem experienced was occasional failure of cables. A supply of the required cables was made and delivered to the mine so damaged cables could be quickly replaced. Much of the cable damage could be eliminated by slight modifications to the miner during a rebuild, so that cables could be installed in more protected locations. After the sensor had been in operation for about two months, a survey was made to determine its effect on continuous miner operations. In previous research, coal thickness measurements made in 88 locations by the natural gamma method were compared to measurements made in the same locations by observing drill cuttings and by inspections of drill holes with a borescope. That research showed that the gamma method is at least as accurate as the other two methods (Nelson and Bessinger, 1989) and is also much easier to use. The object of the survey described here was not to assess the accuracy of the natural gamma measurements. but rather to determine the effectiveness of the sensor output as a guide for the operator in maintaining control of the cutting horizon. Thus a smaller, hand-held gamma detector

Jan 1, 1992

By A. H. Srnallbone

Over the past few years the rising production costs, shortage of skilled labor, and increased use of lower grade ore bodies have all added justification for the use of on-stream analysis. A rise in the number of on-stream units indicates that this type of assay is now being accepted as a necessity. On-stream analysis is a much more rapid means of obtaining true assays of a flowing product when compared to wet chemistry or "grab" samples dried, briquetted and assayed by x-ray. In contrast, on-stream analysis uses real time samples assayed every 30 seconds while each stream is assayed every 5 to 15 minutes. It is very important not only to know that a change has occurred in the process, but to know what caused the change and how to correct for the change. For example, in a tailing sample the elements of interest comprise between 1% and 10% of the sample. The remainder is water and gangue. Previously the gangue was not assayed nor were the low atomic number elements used for corrections. In addition to the demand for higher accuracies some concentrators were being penalized for excessive Ca or in some cases 5i in their concentrates. This penalty was being imposed by the smelter in order that they could better cope with pollution problems and prolong the life of their furnaces. But until Ca, 5i, and S are measured on-line, nothing can be done about their control. By accurately measuring these light elements on-line, a complete assay is obtained of the total sample providing improved accuracy for the important products. The justification for complete accuracy assays is now even more obvious because they are possible at very 1ittle increased cost and at no increase in analytical time.

Jan 1, 1977

By R. L. Atwood

The structure, properties, and composition of commercial chelating-type copper extractants are examined. Characterization of these extractants was accomplished using organic separation techniques and analytical tools such as NMR and IR. Results indicate that only the trans isomer of the diphenylhydroxyoxime (LIX (R) 64N) is capable of copper chelation. The effect of the structural modification of the extractants on the extraction and stripping reactions are discussed.

Jan 1, 1972

The impact of a methane explosion on mining operations cannot be over-emphasized. The explosion is a result of rapid combustion when a methane/air mixture is ignited by an unexpected energy release, such as a mine fire, electrical arc or sparks caused by frictions or rock falls. In most cases, an ignition of methane/air mixture could result in a deflagration other than detonation. Resulting flames and overpressure induced by a methane deflagration will harm neighboring miners and local ventilation control devices.. ,It is essential that the mechanism of an explosion and associated destructiveness be fully understood. This research seeks to predict an influence region of an incident happened within a representative underground mine geometry. The most common geometric changes in an underground coal mine are bends, regulators/doors, obstacle in airways and changes in sectional area. These geometric changes could result in an attenuation of the flame and pressure wave as a result of a methane deflagration. A study of this phenomenon could enable mine planners to have better understanding of the over-pressure redistribution due to the explosion. Both numerical and experimental work has been done in this study to ascertain a better insight of this potentially devastating event. The experimental data are also used to validate the turbulence and combustion models used in this test.

Feb 23, 2014

"The adsorption of mixed cationic/anionic surfactants with different molar ratios onto quartz was investigated. The cationic surfactant used was dodecylamine bromide (DDA), and the anionic surfactant was sodium oleate (NaOL). The critical micelle concentration values for the individual surfactants and their corresponding mixtures were determined using a platinum plate. The adsorption mechanisms of mixed surfactants on quartz were studied using contact angle measurements, flotation tests and adsorption amount measurements. At alkaline condition, NaOL depresses DDA flotation of quartz without depressing the adsorption of DDA. The molar ratio of mixed surfactants is found to be a key factor in the orientation of alkyl chains and thereby the flotation response of quartz. A mixture of 1/2 or 1/3 DDA/NaOL forms on the surface of quartz when the concentration of NaOL is higher than that of DDA. The adsorption of the mixture decreases the wetting of quartz since the alkyl chains are in chaotically orientation with a conceivable number of head groups directing towards the solution phase. These results provide important insights into the adsorption of mixed surfactants onto quartz surface. INTRODUCTION Froth flotation is known as an effective method of separating mineral particles on the basis of their surface chemistry, specifically their hydrophobicity. [1]. The hydrophobic particles will attach to the bubbles and rise to the top of the containing vessel to form a froth that flows over the lip of the vessel. The hydrophilic particles remain in the liquid [2]. In the process, surfactant is often used as collectors for surface modification in order to change the wetting properties of mineral particles. The primary long chain alkyl ammonium salts are the most widely used as collectors for the flotation of oxide minerals, such as quartz, muscovite, hematite, phosphate and feldspar [3, 4]. Adsorption mechanism of alkyl ammonium salts on oxide minerals has been extensively analyzed [5, 6]. Generally, the ammonium salts are adsorbed through electrostatic interaction of the polar group of the molecules with the surface of these minerals [7]. Despite many obvious advantages of the ammonium salts in low temperature resistance and hard water resisting, however, their unavoidable drawbacks, such as high sensitivity and poor selectivity for slimes, relatively high cost, have limited their applications [8]. In recent years, mixed surfactants have drawn much attention due to their superior physicochemical and surface properties than single surfactants [1, 9-11]. They have been used in many industrial processes such as dispersion/flocculation, flotation, detergent, corrosion inhibition, cosmetics, foods, paints, chemical mechanical polishing, enhanced oil recovery, and nanolithography [12]. Most of the mixed surfactants have synergistic advantage in reduction of the surface tension and critical micelle concentration (CMC); therefore, they exhibit spurious properties, like excellent surface/interfacial activities, and are less expensive than single mixed surfactant systems [13, 14]."

Jan 1, 2016

By J. M. Wempen, M. K. McCarter

"Differential Interferometric Synthetic Aperture Radar (DInSAR) is a satellite-based remote sensing technique capable of measuring centimeter-level surface displacement with high spatial resolution over large areas. Regular monitoring of subsidence due to underground mine development is one potential application of DInSAR, and in this study, the application of DInSAR for subsidence monitoring is evaluated for two mining regions in the mountain west of the United States. In general, DInSAR has potential to identify the shape and extent of subsidence; in some cases, magnitudes and rates of subsidence can be defined. Importantly, the effectiveness of DInSAR for subsidence monitoring depends on the radar band (wavelength), the subsidence rate and the time between image acquisitions, and the topographic and vegetative surface characteristics. INTRODUCTION Differential Interferometric Synthetic Aperture Radar (DInSAR) is a satellite-based remote technique that can be used to measure small surface displacements. Under good conditions, centimeter-level displacements can be measured with subcentimeter accuracy (Buckley, 2000; Massonnet and Feigl, 1998). Additionally, DInSAR data have relatively high spatial and temporal resolutions. Pixels in Synthetic Aperture Radar (SAR) images can have a ground resolution as small as about 3 m, and images often include tens to hundreds of thousands of pixels and cover tens of kilometers. Regions are imaged regularly, and periods between images typically range from weeks to months. In DInSAR, phase measurements from two radar images acquired over the same region at different times are used to precisely measure relative distances (Rosen, 2014). Surface deformation, topography, and changes in the satellite position all contribute to differences in the length of the path that the radar wave travels in each image. SAR sensors use radar with relatively long wavelengths; L-band (24 cm wavelength), C-band (6 cm wavelength), and X-band (3 cm wavelength) radar are used most commonly. Because the wavelengths are long, small changes in the path length of the radar signal can be quantified by measuring the change in the phase of the radar signal between the images. In general, changes in the path length due to changes in the satellite position and topography are known or can be estimated, and centimeter-level changes in the path length due to deformation are measurable. This study evaluates the effectiveness of DInSAR for measuring subsidence in two mining regions in the mountain west of the United States. L-band data from the Advanced Land Observing Satellite (ALOS) and X-band data from the TerraSAR-X mission are evaluated. Imaging characteristics, including the radar band and the time between image acquisitions, are important for effective subsidence monitoring."

Jan 1, 2017

By J. Kretschmann

Southeast Asian countries cannot maintain their economic growth rate without the development of their mining industries. To make this development as sustainable as possible requires sound fundamentals securing not only economic progress and environment protection but also improvements in occupational safety and health (OSH) for the miners. Mining in South East Asia is still very labor intense and dangerous. Tremendous achievements from world class mining operations in advanced mining countries can be used as role models to improve the status quo of the Southeast Asian countries in OSH management. Know-how transfer, therefore, is a key factor for major improvements. Effects of this transfer based on a multi-level approach will be discussed based on a case study. It describes the transfer from German to Vietnamese hard coal mining industry. Crucial requisites for excellent achievements in OSH in Southeast Asian mining countries are also mentioned.

Feb 23, 2014

By J G. Dunn, S M. Thurgate, A C. Chamberlain, P Franzmann, M Jeffrey, L J. Warren, G E. Poinen, T Williams

Gold has always fascinated mankind. From Tutankhamen's mask to the huge nuggets that have been found in the Australian outback, gold has quickened the pulse and fevered the eye. But in recent years, governments around the western world have shown a singular lack of interest in research into gold processing, with many programs being cut. There are some notable exceptions, fortunately, and this paper summarizes a large research effort that is well supported by the Australian government and the Australian gold industry. The AJ Parker Cooperative Research Centre for Hydrometallurgy is an unincorporated joint venture between the CSIRO Division of Minerals, Murdoch University, Curtin University of Technology and the Western Australian Department of Minerals and Energy. The Australian Mineral Industry Research Association (AMIRA) is the Parker Centre's broker for generic R&D contracts with industry. Each of the partners makes available staff, students and equipment to further the work of the Parker Centre, and the Australian Government provides additional funding. The Parker Centre is nearly five years old and has grown spectacularly in that time. There are now about 30 full-time-equivalents of effort from 50 scientists and engineers, as well as about 40 postgraduate and honours students. The fundamentals of the key operations in hydrometallurgy are studied in three programs: leaching (which includes pretreatment by roasting etc), precipitation (or crystallisation), and surface processes (which includes solid/liquid separation, adsorption, solvent extraction, etc). A large part of the Parker Centre's R&D is directed towards gold processing technology. In Australia, a dramatic increase in gold production, from about 30 to nearly 300 tonnes per year (1977-1997), has been made possible largely as a result of a brilliant metallurgical innovation, the carbon-in-pulp process. However, falling head grades eg 2.56 to 1.84 g(Au)/t over the last 10 years, and environmental concerns, are squeezing profit margins. There is increasing pressure to reduce costs, and the Parker Centre program is focussed on providing the scientific understanding required to do this. A selection of research highlights will be given, to indicate the depth and breadth of the R&D at the Parker Centre.

Jan 1, 1997

By C. A. Rowland

When studying the feasibility of using autogenous or semi-autogenous grinding, operating and engineering companies frequently request assistance from the mill manufacturers in three areas - 1. Recommendations for studying the suitability of autogenous or semi-autogenous grinding for the specific ore. 2. Mill sizing, to accomplish required grind. 3. Recommendations on mill design and operation. Rod mills and ball mills are selected by the use of bench scale standard grindability tests and established calculation procedures, of which the most frequently used are the Bond Grindability tests and the Bond Work Index equation(1). The accuracy of these have been reviewed by C. A. Rowland in his papers, showing the correlation of work indices calculated from plant operating data and laboratory grindability tests(2)(3). The selection of autogenous and semi-autogenous primary mills has not reached the stage where mill size selection can be made from bench scale tests. Considerably more extensive testing will be necessary than required for selecting rod mills and ball mills.

Jan 1, 1974

By James S. Browning

Extensive deposits of kyanite occur in the southeastern United States, The reserves of these deposits, if developed, are adequate to supply the United States with 35-mesh kyanite concentrate:; for many years at the present-rate of consumption, According to Espenshade and Potter,1 the kyanite-quartz rock type deposits in this area contain about 100 million tons of ore averaging 10 to 30 percent kyanite. The tonnage of kyanite-bearing gneiss and schist is, much larger than the tonnage of kyanite-quartz rock, but the kyanite gneiss and schist are appreciably lower in grade. The largest deposits of kyanite-quartz rock are in the Farmville district, Virginia, and Kings Mountain district, North Carolina South Carolina, and at Graves Mountain, Georgia. Of the known deposits, only four were being mined for kyanite in 1967. These deposits are near Farmville and Dillwyn, Va., Clover S. C., and Washington, Ga. Production of kyanite and synthetic mullite increased substantially in 1965.2 Output of, domestic kyanite concentrate increased by 14 percent in 1965, establishing a record high for the fifth consecutive year. Estimated annual consumption of kyanite minerals and synthetic mullite was in excess of 100,000 tons. The manufacture of mulatto refractories accounts for most of the kyanite minerals consumed annually, but non-refractory uses are expanding.3 Most mullite refractories are used as furnace linings in metallurgical and glass manufacturing furnaces. The remainder is used largely for kilns, kiln furniture, and saggers by the ceramic industry. Small quantities of kyanite without calcination are used as a source of alumina in the manufacture of glass, electrical and chemical, porcelain, pyrometer tubes, and in the form of kyanite concentrate to increase the alumina content of fireclays. Kyanite is used to improve workability, increase strength, and to compensate for firing shrinkage in floor and wall tile and other ceramic products.

Jan 1, 1968

By T. Diering

Gemcom PCBCTM is a software package which has been developed over the last 22 years for the planning and scheduling of block cave mines. This paper presents an update of the various research and development activities done to PCBC recently. It also provides an overview of the current capabilities of the software including tools for both feasibility type studies as well as tools for operating mines. PCBC is used extensively by prospective and operating block cave mines and some of the recent applications are described.

Jan 1, 2010

By B. W. Lawrence

Shaft alignment requirements are consistently met using conventional shaft sinking methods. Little attention has been given to achieving similar alignment accuracies using rotary drilled shaft methods. Alignment of these shafts is difficult to control and guarantee. Bare shafts and shafts that use drum hoisting systems can accept some deviation. However, combining drilled shafts with Koepe hoist installations presents new accuracy requirements for drilled shafts. This paper describes the importance of verticality with practical examples, and discusses various methods of measuring verticality and their respective limitations.

Jan 1, 1989

By M. A. Cristovici

The possibility of using surfactants as wetting agents for the suppression of sulphide ore dust has been investigated. Numerous surfactants were examined to determine their characteristics and to investigate their ability to improve the wetting of the sulphide ore dust. However, the surfactants selected as suitable dust suppressors proved to have a negative effect on the flotation of the ore contaminated with such reagents. A method was developed to eliminate the detrimental influence of dust-suppressing surfactants. It consisted of surfactants adsorption on activated carbon and separation of loaded carbon prior to flotation. The technique is simple and requires minimal changes in the plant flowsheet.

Jan 1, 1990

By A. J. Guse

The primary limiting factor for hoisting capacity from great depths is the self-weight of steel wire ropes. Steel wire ropes are very suitable for mine hoisting due to their high strength and durability, but have the negative characteristic of a low strength/weight ratio. Also, as hoisting depths increase, the service life of steel wire ropes decreases due to the higher stresses and physical effects on the ropes. The significantly higher strength/weight ratio of synthetic ropes offers the primary advantage of hoisting a larger payload with a similar size rope and hoisting plant. The beneficial properties of synthetic ropes could be used to improve the overall economics of deep underground mining both for new deep shaft projects and for existing mining operations expanding to deeper orebodies. A research and development program has been initiated to evaluate the suitability of a fully synthetic rope for the mine hoisting application.

Feb 23, 2014

By J. A. Domenico

A safe and precise mineral separation alternative to heavy liquids is being used for mineral sands exploration on large scale orebodies. The separation process, Magstream®, uses ferro-fluids and magnetic and centrifugal forces to produce precise split points over a range of specific gravities from 1.5 to 18.0 g/cc. This paper describes a commercial scale exploration program treating, roughly, 90 samples per day in Senegal (West Africa). Separation results comparing Magstream® and conventional heavy-liquid separation are presented.

Jan 1, 1994