Search Documents

By A. R. Laplante

A novel methodology to estimate gold recovery by gravity is presented. The methodology makes use of a population balance model which represents gold liberation, breakage and classification behaviour and applies pre-concentration and recovery performance curves to gravity-recoverable gold to predict overall recovery. Derivation of the necessary parameters is explained and demonstrated using data from an actual gravity circuit and one projected application. The methodology makes it possible to estimate the performance of circuits with large gold circulating loads and relatively low unit recoveries (e.g. jigs), or with high recoveries on a bleed of the circulating load (e.g. Knelson concentrators).

Jan 1, 1994

By P. Zhang

Phosphate mining in Florida generates approximately 100,000 tons/day of phosphatic clays (slime). This waste slime not only creates one of the most difficult disposal problems in the mining industry, but also causes tremendous loss of P2O5. About 20-30% of the phosphate mined end up in phosphatic clays. Recovering the phosphate from this waste is difficult for two main reasons: 1) the slime is extremely fine in size, and 2) clay minerals account for almost half of the material. A half dozen dispersants were evaluated for keeping the clay minerals suspended for subsequent separation from non-clay minerals by either settling or cycloning. The separation efficiency and economics are discussed.

Jan 1, 1998

By J. Choi

For the first time, the influence of stearyl trimethyl ammonium chloride (STAC) as a collector, on the flotation behavior of lepidolite (Uljin, South Korea) was systematically examined in Denver Sub-A cells. Flotation tests were carried out by varying amount of STAC (50?200 g/ton), feed size (-65, -100, -150, and -200 mesh), and solution pH. The impeller speed of 1000 rpm, flotation time of 10 min and AF-65 (a frother) of 250 mL/ton were invariably applied. In order to complement flotation experiments, zeta potential measurements and XRD analysis were conducted. XRD results showed that the ores were mainly composed of lepidolite, muscovite, quartz, calcite and albite. In addition, zeta potential results showed that isoelectric points were about 2.5, 2.3, and 9.7 for quartz, albite, and calcite, respectively, and lepidolite was determined to be less than 2. Overall, the results of 3-stage flotation showed that Li2O grade and recovery tended to increase with increasing STAC dosage and decreasing feed size. In addition, Li2O grade increased with decreasing pH. The results were explained by the extent of the interaction between STAC and each mineral.

Feb 23, 2014

By O. Salami, G. Xu

Fire accident is one of the most classic safety concerns in underground mines both in the USA and abroad. It may occur from pool fires due to leakages in hose or pipes, vehicle fires, or fires in tires and conveyor belts in the underground mines. It may also result from the storage of flammable materials such as gasoline, diesel, and explosives in the underground. When fire occurs in an underground mine, it releases heat, smoke, and other toxic gases such as carbon monoxide, and methane to the surrounding thereby making life unbearable to the miners. Furthermore, smoke greatly impact visibility in the underground which makes evacuation even more onerous and challenging. To this end, a thorough investigation of fire behavior and spread of toxic gases in a practical underground mine is imperative to develop a reliable emergency evacuation plan in an event of fire disaster in the underground mine. The objective of this study is to investigate temperature variation and CO spread along mine airways by conducting full-scale fire experiment in the underground mine. The results presented from this study are crucial to developing evacuation plans in underground mines. In addition, the findings from this study could be used to validate existing evacuation models.

Mar 2, 2022

By Francois J. E. Scholtz, Raymond J. Davidson, Peter Greenhalgh, R. Paul Riley

A 1 t/d continuous elution pilot plan is being operated by General Mining at their Grootvlei Gold Mine using the technology developed at the Anglo American Research Laboratories. Flowsheet design and plant erection was carried out by Van Eck & Lurie and completed in December 1989. Following the conclusion of six test runs designed to optimise reagent additions, it was shown that elution efficiencies of 98-99% could be achieved using reagent additions as· low as 16 kg/ton of carbon NaCN and 28 kg/ton NaOH while consistently producing eluted carbon containing less than 50 g/t gold. Significant savings were indicated when compared and power were indicated when com­pared with the traditional batch AARL, Zadra and Micron alcohol elution procedures.

Jan 1, 1990

By Sepp A. Kutschera

are gaining increased interest for over­burden removal and ore production at large open cast mines. The application of bucket wheel excavators is still tied to soft un­consolidated rocks and soils, while belt conveyors can cope with all kind of matri­als restricted only by the top grain _ size. Therefore, mode of transport and the re­quirement of down stream ore processing de­fine the materials size distribution. These requirements are usually met by primary crushing or scalping. The paper discusses general applica­ tion criteria of bucket wheel excavator with systems primary for in-pit overburden crusher removal. and It _indeapits scalper units and discusses their technical and operational features. It further com­pares the capital and operating cost struc­ture relative to the syste

Jan 1, 1992

By A. W. Khair

This paper presents a strength formula for the design of coal pillars. The formula is derived from results of laboratory experiments, studying the effects of primary factors influencing the strength of the coal specimens/pillars. Five primary factors, significantly affecting the strength characteristics of the coal specimens/pillars were identified and extensive laboratory investigations were carried out. The five primary factors were namely 1) coefficient of friction between loading platens and coal specimens, 2) elastic properties of the loading platens, 3) coal specimen geometry, 4) coal specimen size, and 5) rate of loading. Four to nine levels of variation for each primary factor on the strength of coal were studied. An empirical formula, implementing the variation of the primary factors affecting the strength of coal specimens/pillars, has been developed. A comparative analysis of the results provided by this and some well known formulae is also presented.

Jan 1, 1994

By R. H. Sergent

The interest in using halogens for extracting precious metals from ores has increased due to changes In ore characteristics, environmental concerns and regulations. The rediscovery of halogen leaching capability has been the topic of these and other writers1-30. Much work has been done on the performance of bromine, chlorine and iodine5-29. Of these, bromine and chlorine look most promising. Iodine is quite expensive and sometimes forms an Insoluble film on a precious metal surface22,23. Little experimental work has been published on the relative performance of bromine versus chlorine. The Pourbaix diagrams for the halide leach system (see Fig. 1-4) Indicates a significant stability advantage for bromine In forming complex ions with gold. This should result In greater extraction of gold under similar leach conditions and Is evaluated In this work. The regeneration of halogen from a spent leech solution is a critical requirement for an environmentally acceptable halogen leach process. Bromide can be oxidized In-situ to bromine ~ adding chlorine or ozone2,31. Bromide like chloride can be oxidized In an electrochemical cell to produce halogen on demand 13,15,17. Bromine clearly offers a number of possible regeneration pathways. This work strives to compare the relative ability of chlorine and bromine to extract gold from partially and fully oxidized ores. A commercially pressure oxidized sample was evaluated under a number of experimental conditions. The autoclave feed ore from the same mill was also evaluated after complete oxidation In a laboratory autoclave.

Jan 1, 1993

By P. Guliov

In the first part of this paper the authors present an overview of industrial minerals produced in the Canadian provinces of British Columbia, Alberta and Saskatchewan, and supplied to the Pacific Rim countries. The second part outlines some of the unique opportunities for industrial minerals that exist in the three western Canadian provinces and those minerals we feel have development potential for overseas markets. Because of time constraints, it is not an exhaustive presentation on industrial minerals, but is focused on a few selected minerals that we believe have high potential.

Jan 1, 1990

Caterpillar recently held two, two-day demonstration programs for its mining customers. The event, billed as MineDemo by Caterpillar, consisted of two sessions held on consecutive weeks at the company's Tinaja Hills proving ground south of Tucson, AZ. The program included several classroom sessions that focused on Caterpillar equipment applications, including the VIMS (vital information management system) and the CAES (computer-aided earthmoving system). Also included were field demonstrations and the opportunity to test drive mining-related heavy equipment, including dozers, trucks, graders, shovels and loaders. Featured at the event were the recently upgraded 785, 789 and 793 C-Series trucks. Caterpillar recently announced the availability of the 136-t (150-st) 785C and the 177-t (195-st) 789C. The upgraded haulers have replaced the respective B-Series models. The 218-t (240-st) 793C was introduced in 1996. It, too, has been upgraded but retains the C-Series designation. While attending the press event, the author had the opportunity to test drive the 793C at the Tinaja Hills test site. It was amazing how well the machine handled. The operation was smooth and the braking system was precise. The cab was extremely comfortable. To see a C-Series truck in action, the author also visited Newmont Mining's Mesquite Mine, located in Cali¬fornia, across the border from Yuma, AZ. The Mesquite Mine operates a new model 785C truck. At the mine, temperatures have been measured as high as 58° C (138° F) in the pit. Needless to say, the ability to operate dependably in extreme heat is an important consideration for the mine operators. An interview with the driver and later with management confirmed that the 785C has worked out well. The driver praised the comfort of the cab and the ease of operation. Management reported significant fuel savings and was impressed by the truck's maintenance features.

Jan 1, 1999

By Y. H. Zhan

A new P(MAAA) latex was developed and used in separation of ultrafine apatite from calcite and silica by means of selective flocculation. The latex was found to flocculate selectively apatite from apatite/calcite and apatite/silica mixtures in the presence of sodium tripolyphosphate and sodium silicate over a pH range from 9.1 to 9.4. The separation of apatite from calcite was more selective with sodium tripolyphosphate, while the results of the separation of apatite from silica were better when sodium silicate was used. In the apatite/calcite system, 90% apatite recoveries into a concentrate containing 34% P2O5 were possible in the presence of 4 mg/l of sodium tripolyphosphate at a latex dosage of 2.2 kg/t. In the apatite/silica system, 80% of apatite could be recovered into a concentrate containing 33% P2O5 in the presence of 20 mg/l of sodium silicate at a latex dosage of 1.1 kg/t. Deposition tests were used to study the interaction between the latex and the mineral surfaces. The results revealed that deposition density of the latex on apatite was higher than on calcite; the differences between the deposition onto these two minerals were higher at pH 9.2 than at 7.2. The results point to the stronger interaction between the latex and apatite surface when compared with the latex-calcite interactions.

Jan 1, 1998

Laboratory tests were conducted to evaluate the silica collection efficiency of flooded-bed scrubbers with six different filter panel designs and at two operating velocities. Test results indicated that reductions in filter density negatively impacted respirable dust collection. Silica collection efficiency for the least dense filter was as much as 33 % lower than the collection efficiency of the densest filter. At the low operating velocity, the least dense filter allowed over 40% of the respirable silica dust in the scrubber intake air to pass through the unit, where it would be discharged back into the mine environment. Operation of the scrubber at the higher test air velocity increased silica collection efficiency, regardless of the filter panel tested. The density of the filter panels also impacted the quantity of air that is moved through the scrubber, with higher density filters reducing scrubber airflow. For each filter, the relationship between dust collection efficiency and air moving capacity must be considered to determine overall effectiveness for specific mine applications.

Jan 1, 1998

By L. M. Sandoval, R. Kaunda, C. N. Vasquez, S. C. Falcon

Artisanal and small-scale mining (ASM) involves a wide range of practices, from highly informal and minimally mechanized mining operations with predominantly manual work to formal practices carried out by small but high-tech industrial mining operations [1]. ASM may be a traditional practice, with skills passed from one generation to another. It can be an important driver of local economic development, while simultaneously contributing to a complex array of positive and negative socioeconomic and environmental impacts. There are more than 100 million artisanal and small-scale miners in 80 countries worldwide, and they supply around 20% of the worldwide gold production [2]. According to the Peruvian Ministry of Energy and Mining (MINEM), in 2020, 32% of fatal accidents in formal (legal) Peruvian mining operations were caused by groundfall events [3].The lack of resources, knowledge of best practices in health and safety, and insufficient equipment used in ASM make the probability of suffering work accidents very high. Furthermore, groundfall is one of the main causes of accidents and injuries in underground mines around the world [4], and it is also a concerning problem in ASM, where the associated fatality rate is similarly high. Unfortunately, a proper record of accidents in ASM is not kept, so an estimate of the actual number of groundfall accidents cannot be accurately developed [5]. Currently miners rely on empirical and observational tools acquired through previous experience to assess groundfall risks. The risks for artisanal miners can tend to be significantly greater than risks for those from the mining industry. This is due to the lack of regulation of ASM, which tends to operate outside the legal framework and the regulations lack of enforcement in force for occupational health and safety regulations.

Mar 2, 2022

By L. Yuan, J. Soles, W. Tang, R. Thomas

Lithium-ion battery pack fires pose great hazards to the safety and health of miners. A detailed experimental study has been conducted at the National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Mining Research Division (PMRD) to investigate the effectiveness of different fire suppression systems on Li-ion battery pack fire extinguishment. Tests were conducted in a well-ventilated container. Two sizes of battery packs (12V, 24V) were heated by heater strips to trigger thermal runaway and fire. Water mist with different flow rates, ABC powder, type D dry chemical, and water mist with F500 additives were used as the fire suppression agents. Multiple thermocouples were installed on the battery packs to measure the temperature evolution during the tests. The results indicated that the water mist with F500 additives is the most effective suppressant among the agents tested. Dry chemicals, however, do quench the fire for a moment, but cannot prevent re-ignition of the battery since they do not provide enough cooling. The findings of this paper can be used to develop safer battery fire suppression techniques in mining environments.

Feb 1, 2023

By Richard J. Robbins

This paper is presented with particular reference to the findings of the OECD Advisory Conference on tunneling held last July in Washington D. C. A great deal has been said about the Conference in the past few months, but it may be appropriate to review briefly the background and objectives of the Conference to better understand how the mining community can relate its underground excavation problems to the results of the Conference. OBJECTIVES OF THE OECD CONFERENCE The world demand for tunneling (the term tunneling is used here loosely to include almost all forms of underground excavation) is expected to grow at an in- creasing rate. During the decade of the ?70's, the demand is expected to at least double by comparison with the previous decade. Much of this increase in demand will be due to the rapid growth of urbanization around the world. As urban populations grow larger and denser, the conservation of surface land and the quality of the environment become more important. This aspect of the increasing demand poses a difficult challenge to those who must plan and implement urban development.

Jan 1, 1970

By J. F. T. Agapito

The load carrying capacity of oil shale pillars excavated by conventional blasting, presplit blasting, and mechanical mining is evaluated. The study was based on a comparison of in-situ vertical stresses and fractures obtained from overcoring horizontal holes in the Colony Mine, Piceance Creek Basin, Colorado. Results indicate that conventional blasting causes a zone of damage approximately 3 m (10 ft) thick with low stress distributions. Presplit blasting reduces damage significantly, and increases the load carrying capacity in the 3 m (10 ft) thick zone by 5.93 MPa (860 psi). Mechanical mining causes little or no rock damage, and an increase of 9.83 MPa (1425 psi) in strength in the same 3 m (10 ft) thick zone. An example of pillar design is given showing that the use of presplit blasting and mechanical mining techniques can increase the extraction ratio by at least three and five percent, respectively, as compared to conventional blasting. It is speculated that comparable increases in extraction should also occur due to increases in span dimensions.

Jan 1, 1984

By Andrew Torok

Activated bleaching clays, so called because of their ability to remove color bodies from bleach fats and oils, are produced from clays of bentonitic origin. Activation is achieved by subjecting these clays to physical or chemical alteration to increase selective sorption capacities (1) . The future of activated bleaching clays depends upon the ability of producers to recognize the new areas of applications which are arising, and their skill in developing sophisticated active clays to meet new and stringent requirements. The major portion of activated bentonites are produced for decolorization of oils. New techniques of activation will improve these clays for broader spectrum use. General properties expected to result from present activation methods are: 1. Modification of hydrophobic-hydrophilic properties and increased available surface area in non-aqueous systems, thereby improving sorption capacity and ability to remove color bodies from oils. The following additional properties will be expected from future activated clays: 2. High purity of the active clay with interfering impurities totally removed. 3. Increased selective sorption capacity in aqueous systems. 4. Selective chemical reactivity, such as oxidation or hydrolysis. This property is required for removing

Jan 1, 1971

By DeVerle Harris

The enthusiasm with which individuals have participated in mineral exploration in the development of this country testifies to the fact that there was once a very real probability of making a worthwhile discovery. Over the years, the discovery and subsequent exploitation of the accessible ore deposits have made the finding of new deposits progressively more difficult. Present day mineral exploration has evolved from the lone prospector with the grubstaker behind him to a very costly and complex business, involving large sums of money and a staff of experts in the fields of exploration technology. Exploration today must be carried out on a large scale to be profitable. With the involvement of large amounts of capital, there has been a good deal of interest in methods of optimization of the allocation of the resources of a firm 'engaged in mineral exploration. As a step toward this, mathematical models have been formulated which are designed to quantify those variables of mineral exploration in such a manner that they can be integrated with all phases of the firms operations so as to optimize its profit objective or more simply, to make exploration more efficient and effective.

Jan 1, 1964

By Charles G. Zink

Anthracite is widely known as a domestic or space heating fuel. The prevailing market ratio of domestic to industrial consumption was about 80 to 20 up until 1950. Since then it has been shifting until now the ratio index is about 50/50, exclusive of overseas export. Despite a declining domestic space heating market, the demand for industrial anthracite remains good. However, as a result of stringent air pollution regulations, there is a renewed interest in this low sulphur coal which cannot smoke under any conditions. Anthracite serves other important industries such as power generating, metallurgical, cement, ceramic, chemical, water sewage and industrial wastes filtration. Anthracite is an excellent natural source of carbon and may be utilized in many processes.

Jan 1, 1966

By T. A. Farr, I. A. Gibbs, F. Guevara, S. R. Simms, G. Nojima

This paper describes an installation of a medium-voltage adjustable frequency motor drive (AFD) on a high starting torque regrinding mill. This type of application is typically found in the mineral industry dealing with hard ore. The AFD electrical architecture is introduced from line to load. The type of closed loop encoder feedback motor control algorithm is briefly described. The results of the AFD motor identification auto-tuning are compared against the manufacturer’s supplied data. The motor drive performance results are shown for pre-ramp DC fluxing, high starting torque with overload current, excessive load torque stall condition, and blocked rotor. The instrumentation and arrangement for the two watt-meter method to capture low frequency data are presented. The data shown is from the input power quality meter, the AFD computer tool, the output motor protection relay, an oscilloscope, and load shaft connected strain gauge (rotating telemetry for torque assessment). These types of high starting torque constant torque loads are found in mining and process industry applications employing AC adjustable frequency drives. Using field results should help demystify the use of voltage matching output transformers in AFD applications including constant torque loads

Mar 2, 2022