Search Documents

By Keith G. Wallace, K. M. (Chris) Chmura, Kirk H. McDaniel

The Waste Isolation Pilot Plant (WIPP) performed a feasibility analysis for the purpose of either modifying, supplementing, or replacing its two main mine fans. The WIPP, located near Carlsbad, New Mexico, is a U.S. Department of Energy (DOE) fa¬cility designed to demonstrate the permanent, safe disposal of U.S. defense-generated transuranic waste in a deep bedded salt deposit. Since the centrifugal fans were installed in 1988, multiple op¬erational and performance concerns have been identified. A com¬prehensive engineering study was conducted in 1995 to: 1) Qualify and quantify operational concerns, 2) Evaluate possible alternatives, and 3) Recommend an optimum solution. Multiple system modification and/or replacement scenarios were evaluated with associated cost estimates developed. The study considered replacement with either centrifugal or axial fans. Multiple fan duties are required at the WIPP. Therefore, Variable Frequency Drives and Inlet Vane Controls (IVC) were investigated for centrifugal fans. In-flight adjustable blades were investigated for axial fans. The study indicated that replacing the existing system with two double-width, double-inlet centrifugal fans equipped with IVCs was the best choice. This alternative provided the most desirable combination of: 1) ensuring the required operational readiness, and 2) improving system performance. The WIPP is currently planning to replace the first fan in 1997.

Jan 1, 1997

By D. R. Kalasky, J. M. Mutmansky, B. Kolonja

This paper considers simulation of truck dispatching systems using maximum expected production of the truck-shovel system as the measure of performance. Two analysis methods are utilized: multiple comparisons with the best (MCB) and the combination of MCB with the variance reduction technique known as common random numbers (CRN). These two techniques are compared via simulation experiments. Results show that the combined procedure of MCB with CRN is the superior tool to use to reduce the total number of replications needed to ensure the specified probability of correct selection from a number of systems. In this case study, MCB with CRN reduced the variance by 29% and the number of required replications by 48%. Also, the MCB with CRN procedure narrowed the confidence interval by 18%.

Jan 1, 1995

By Fang-tu Wei

The purpose of developing this system is to monitor the operating status of the fully mechanized mining system in order to raise it's reliability. The completely mechanized coal mining system is a complex dynamic system, involving many sub-systems. It is the key of the mining process as well as a connected system composed of each working procedure. Any hitch in breaking, loading or transporting will interrupt the mining process. The analyses of the operating data has proved that the reasons causing the interruption of the extracting processes mainly come from the inner of coal face. Hence, after the installation of the MINOS system in England, the delays of belt conveyor sub-system were reduced. But the production increment was not as much as expected.

Jan 1, 1986

By C. J. Bise

Continuous mining accounts for about 69% of the nation's underground coal production. This level is not expected to change much in the near future. This is because continuous mining represents the primary means of under- ground coal production. It is also the primary means of driving development entries for underground coal mines, including longwall mines. The continuous miner worksite contains many characteristics that can lead to personnel accidents. It continues to be an area of concern for mine managers, safety engineers, and training coordinators. In an effort to assist mine management in attempts to reduce the number of accidents and injuries sustained in this area, this paper presents a loss-control-based, non-intrusive strategy for conducting safety evaluations at continuous miner worksites.

Jan 1, 1991

By E. K. H. Goh

A reliability-based engineering design approach for the effective design of reshaped spoil dumps was developed with the aim of obtaining structurally reliable spoil dumps at optimum reshaping costs. The aim was also to satisfy environmental erosion standards and community expectations. This approach encompasses the linking up of three major components: erosion appraisal of spoil dump designs, reliability-based engineering design of spoil dumps and costing of spoil dump reshaping practices. This paper addresses the application of the reliability-based engineering- design approach to the assessment of spoil dump designs for erosion control. Included are various types of erosion prediction models and reliability-based engineering-design analytical techniques. Also included is a case study that demonstrates the application of this approach.

Jan 1, 2000

By David Shuck

On November 1991, Homestake Mining Co. completed the installation of a $5.7-million, 2.7-kt/d (3000-stpd) flotation circuit into the flowsheet of the McLaughlin Mine in California's coastal mountain range, about 113 km (70 miles) north of San Francisco. This addition reduced overall operating costs and improved the gold recovery of the low-grade refractory reserves over that expected from direct cyanidation. In addition, flotation provided a means to generate a sulfide concentrate that is used to supplement feed to the pressure oxidation circuit. The McLaughlin operation started in 1985 as the first pressure oxidation plant for treating sulfide refractory ore. During the mine's short history, efforts have been made to reduce costs and increase production through process development.

Jan 1, 1994

By W. Hennig

Efforts to define sustainability indicators are continuing in the mineral extracting industry and sector research institutions. Comprehensive ‘sets’ of economic, ecological and social sustainability indicators for the minerals industry are a necessary precondition for rationale-based negotiations with stakeholders from society. These tools alone, however, will not suffice in a delicately balanced economy-ecology -social well-being equilibrium with ever shifting valuation of different variables. Individual interests and emotions and also ideologically motivated positions of diverse stakeholders are gaining momentum. The minerals industry therefore has to develop beyond the rational pro-arguments for mining in the form of sustainability indicators also proactively its ‘soft skills’ to deal with expectations, fears and outright anti-mining bias, if it wants to retain the ‘social licence’ to continue.

Jan 1, 2005

By Ch. Arvanitidis

This work concentrates on investigating the development of a geotechnical classification method for the Greek soils, which can readily provide a rough but usable estimate of the main strength parameters of the soil. It is expected that such a system will be useful to the structural engineer for either checking the laboratory results or for providing a direct estimate in cases where no tests have been conducted. The method provides strength parameter values by relating classification or physical parameters of various types of soils and/or in situ observations of geological and physiographical nature to the strength parameters, such as, cohesion, angle of internal friction, compressibility, modulus of elasticity, etc, by means of a statistical approach and the extraction of empirical formulae.

Jan 1, 2006

By Th. Petropulos

The Zn-Ag-Pb mineralization zone near Molai (Greece) was explored by more, than 60 drillholes. Promising results led to the decision of additional drillholes in order to confirm the expected spatial extension of the deposit. A multiobjective approach is described which optimizes the location of a set of 5 additional drillholes. The decision is based on estimation errors for grade, thickness and depth of the main ore bearing layer, with respect to cut-off values for grade and thickness. The linear combination of these variables defines a favorability index which is used for mapping optimal drillhole locations. The map shows several clusters of favorable cells. A declustrering algorithm is used to select a representative cell for drilling in each cluster.

Jan 1, 1989

By P. G. Irwin

Natural resins, those derived from coal and those mined in the Uintah basin, face challenges from synthetic resins that are derived from petroleum sources and rosin or wood sources. In the past, fossil resins from coal were produced by various companies, the last one being Hercules, Inc., which sold BLACKHAWK resin until a fire destroyed the plant in the mid 1970's. Approximately four to fjve million pounds of BLACKHAWK were produced and sold mostly to the printing ink industry. Uintaite, more commonly known as Gilsonite® resin, was widely used by various industries, notably in printing inks, coatings, stains, adhesives, foundry, asphalt paving, and oil well drilling muds. Gilsonite has lost market share over the last thirty years to various synthetic resins particularly hydrocarbon resins that are derived from petroleum sources.

Jan 1, 1990

By Ali Yalçin

The study area is located in the NW of Uluborlu (Isparta). Massive limestones and alluvial deposits form the lithological units of the study area. The average thickness of the alluvium deposit consisting mainly of light brown - red colored and fine grained clastic sediments which derived from the limestone is about 10 meters. The aim of this study to investigate the uses of this alluvial sediments as tile - brick material. For this aim, disturbed and undisturbed samples have been taken from different depths in the alluvial deposits. Mineralogical compositions have been determined by XRD and major oxide contents by XRF. Laboratory experiments have been carried out to determine the technological properties of the samples. The selected major oxide contents of samples vary between A12O3 (24.6 - 24.12 wt %), CaO (0.76 - 4.27 wt %), Fe2O3 (10.21 - 10.29 wt %), MgO2 (1.25 - 1.51 wt %). CaCO3 and MgCO3 values calculated from the geochemical analyses, are between 1.55 - 1.62 and 2.62 - 3.17 respectively. The ratios of grain size of the samples are 82 % for < 0.2 mm and 5 % for > 3 mm. Geochemical analyses and technological features of the samples indicate that these fine grained sediments of alluvial deposit are suitable in terms of uses as tile - brick material. The potential reserve of this tile - brick material has been determined as 40 million tones.

Jan 1, 2005

The stability of mine roofs in permafrost zones is determined mainly by temperature and ice content. The deformation resulting from creep and temperature dependent physical properties of frozen rockmass is the dominant component of total deformation. Roof bolts can consolidate the roof and control its deformation. In this paper, a finite element model for analysis of the effects of roof bolting in a frozen rockmass is presented. The model includes the variables normally encountered when analyzing the effects of roof bolting in rocks. It also accounts for properties unique to frozen rockmass, creep deformation and the change in Young&apos;s modulus with changing temperature. The model shows that, as bolt spacing decreases, there is a trade-off between increased roof stability from increased mechanical support and decreased stability from increased conduction of heat into the frozen roof. This result was expected, and shows that, for a given set of rockmass conditions, including ice content, temperature, particle size, etc., there is an optimum bolt length and bolt density for minimum roof deflection.

Jan 1, 1996

By Frank F. Aplan, G. Rinelli

INTRODUCTION Coal is a solid, combustible mineral substance resulting from the degradation and alteration of vegetable matter largely in the absence of air. In this natural process of coalification, some non-combustible mineral matter is always associated with the combustible material. Coal preparation or cleaning is the process of removing this inert mineral matter from the coal. Preparation is highly successful in removing the large fragments of inert material, but is not very effective in removing the fine inorganic mineral matter intimately associated with the coal. Of the 600 million tons of coal produced in the United States every year, approximately one-half is produced by coal cleaning methods (1). The bulk of this tonnage is cleaned by coarse or intermediate gravity preparation methods (5 inches to 28 mesh, Tyler). Fine cleaning, say, -28 mesh, is done by shaking tables, washing cyclones, and flotation, or, until recently, the fines were either incorporated into the clean coal or simply discarded--not infrequently, the latter. In 1972, only 13 million tons of raw coal were cleaned by flotation in the United States, and from this 8.4 million tons of clean coal were produced (1). The percentage of clean coal produced by flotation in Europe (England, West Germany, Poland, U.S.S.R., etc.) is substantially higher. However, coal flotation has grown rapidly in the United States from only a few plants in 1950 to 31 in 1960 (2) and 66 in 1970 (1). Virtually all new preparation plants incorporate flotation into their basic flowsheet. The essential difference between ore and coal flotation is that for ores the entire tonnage is ground to flotation size, whereas for coal

Jan 1, 1976

By Behzad Khorshidi

"The ultimate objectives of the post-tensioned strands are to connect the precast segments into a ring and provide pre-stress in the tunnel circumference. The method involves inserting the strand through the preliminary embedded duct in the precast concrete segments and then tensioning the strand by jack and fastening it. The post-tensioned strand eliminates the necessity of bolt connections between the segments and may reduce the labor cost and increase speed of lining construction. Pre-stressing of the segmental lining reduces the steel reinforcement or fiber volume in precast segments and/or thickness of the precast segments which would result in reducing the manufacturing cost of them. Pre-stressing would reduce cracking and increase water tightness, and would provide smooth intrados due to eliminated bolt joints and pockets in the tunnel lining. Pre-stressing would increase resistance to internal pressures as well. Further, this system could work very well structurally in tunnels with squeezing rock or tunnels with high seismic loadings. INTRODUCTION OF THE METHODPost-tensioning is commonly used in the construction of bridges, large buildings, nuclear power stations, and water tanks but its utilization in tunnels is still in its infancy.The precast pre-stressed concrete segmental lining can be used for shield tunnels. It provides a reinforced lining ring by the following construction stages and as shown in Figure 1:1) Segments to be assembled by TBM to complete a full ring2) Steel strand to be inserted through embedded duct (sheath) within the segments3) The strand to be tensioned by Jack after anchorage of the other end4) The strand to be fastened after reaching required tension load5) The horizontal strands (if necessary) to be installed, tensioned and fastened6) The recesses and gap between strand and duct to be filled by groutingFurther, Figure 2 shows an unbonded post-tensioning strand model; Figure 3 shows an anchor sample (Xanchor); Figure 4 shows a duct (sheath) and anchor within reinforcement; Figure 5 depicts the posttensioning of a strand by jack; and Figure 6 is an image of the Midorigaoka Trunk line tunnel in Sagamihara, Japan which was constructed using this system."

Jan 1, 2016

By Ramamritham Sridhar, Vaikuntam I. Lakshmanan, Dan A. Macki

Historically, introducing new technology to the mining industry has been problematic. In general, the industry is reluctant to take risks with new technology because it is already heavily tied to risk, even using existing technology. Risk in the orebody itself can be substantial. The company is dependent on drill hole patterns that are expected to define what is underground, and process test work is often based on drill cores and other samples, which occasionally produce surprises. And even well-proven processing techniques can blindside the producer, resulting in embarrassing and costly difficulties. But if the industry is to grow in knowledge and become more efficient, new ideas must be introduced. How to introduce new technology is the essence of this paper.

Jan 1, 2001

By John R. Marks

Few if any mines in North America have used exhaust air to remove heat at temperatures above the stope reject temperature. In contrast, the South African mining industry has long taken advantage of this heat removal method. The Homestake Gold Mine in Lead, South Dakota, has reached the point where a large air-conditioning upgrade is needed. Since existing air and water resources are being utilized about as well as practically possible, it was recently decided to install an 8.1 MW(R) (2300 ton) plant in the deepest mining division. Two horizontal bulk air spray coolers will distribute the coo1th to active workings via controlled recirculation. The heat will be rejected to exhaust air in four parallel cooling towers. The number and size of these large direct-contact heat exchangers prompted an investigation into South African planning techniques.

Jan 1, 1987

By Y. J. Wang

In the, mathematical analysis of electrical networks, the electrical devices are often modeled using idealized network elements such as current sources, voltage sources and resistors. An analogous approach is outlined for the modeling of mine ventilation networks, which can be considered nonlinear resistive networks. The proposed modeling technique uses the following five basic (nonreducible) elements: H, Q, D, R and N. These elements are characterized by their pressure gain or loss, their air quantity and their pressure-vs. -quantity relationships, each of which may be known or unknown. In addition to the definition of the basic elements, the necessary conditions for which there exists a unique solution are discussed This is performed using theoretical developments derived from electrical circuit theory and illustrated in example networks. The proposed procedures are useful in the solution and characterization of mine-ventilation networks.

Jan 1, 1997

By Denis M. Riley, Neville C. Lockhart, Bruce A. Firth

The potential use of the Kelsey Centrifugal Jig to clean fine coal has been studied. It was found capable of cleaning coal at very fine sizes, at least to 0.038 mm at relative densities as low as 1.6. This effect was however very dependent upon the solids feed rate and the absence of significant amounts of clay slimes. Comparisons with a spiral and a laboratory scale Jameson Flotation Cell were made. The concept of recleaning spiral product was investigated. Use of a spiral to reclean the coarse fraction, and a centrifugal jig or flotation to treat the fine fraction, gave significant improvements in final ash values over spiral recleaning of the full size. Future R&D needs include improving feed rate capacity, and application to problems like pyrite removal that are difficult to solve via flotation.

Jan 1, 1995

By Jan M. Mutmansky, Y. J. Wang

In the mathematical analysis of electrical networks, the electrical devices are often modeled using idealized network elements such as current sources, voltage sources and resistors. An analogous approach is outlined for the modeling of mine ventilation networks, which can be considered nonlinear resistive networks. The proposed modeling technique uses the following five basic (nonreducible) elements: H, Q, D, R and N. These elements are characterized by their pressure gain or loss, their air quantity and their pressure-vs.-quantity relationships, each of which may be known or unknown. In addition to the definition of the basic elements, the necessary conditions for which there exists a unique solution are discussed. This is performed using theoretical developments derived from electrical circuit theory and illustrated in example networks. The proposed procedures are useful in the solution and characterization of mine-ventilation networks.

Jan 1, 1998

By John C. Schneider

In the mid 60's Prochem & Hydrochem Development, it's research division, developed the high efficiency Maxflo impeller. Since the Maxflo impeller had a design that had proven to be very efficient in gas-liquid-solid contacting, it was a natural extension to apply this design to flotation & the research commenced in the mid 80's. An opportunity to test the energy savings occurred at Dickenson Mines in 1987, & comparative results with existing conventional flotation cells showed a marked increase in capacity, grade & recovery with 25% less power applied. This r success was followed by the installation of the fist agitated Flotation Colunm (5ft. dia. x 25ft. tall). As a result of the Dickenson success, Hydrochem started a comprehensive 2-part research program in 1988. At Randol Gold Forum 1988 a paper by Hydrochem was pre

Jan 1, 2000