Search Documents

By A. D. Davis, G. A. Zabolotney

A ground-water flow model was developed to simulate the postmining recharge rate from precipitation at the Belle Ayr surface coal mine, which is located in the Powder River Basin near Gillette, WY Wyoming state regulations require that reclaimed lands should provide a rate of recharge that approximates the premining rate. Steady-state calibration and transient simulations showed that the postmining recharge rate through spoil is at least 50 mm (2 in.) per year, exceeding the original infiltration rate of 4 mm (0.16 in.) per year to shallow overburden aquifers. Major reasons for the increase include the flat topography of the reclaimed areas and the decreased spoil density. It is expected that the backfill will disaggregate and settle over time, eventually resulting in a nearly constant recharge rate that is less than 50 mm (2 in.) per year but still somewhat greater than the premining rate.

Jan 1, 1997

By R. Poulin, A. Lamontagne, N. Tassé

This paper presents the results of a laboratory investigation aiming to verify the concept of co-mingling of waste rock with layers of compacted tailings. Overall, co-mingling is expected to delay the onset and reduce the magnitude of acid mine drainage (AMD) production in waste rock. To denionstrate the efficiency of the method proposed, five different column tests have been set-up. Columns were fed with deionized water at the top and drainage waters were collected and analyzed. Bacteria counts were done on the tailings and waste rock after the column tests. Permeability in saturated conditions and capillary parameters were measured for the tailings. The results obtained show that the co-mingling method would be effective in mitigating AMD by maintaining nearly water-saturated conditions in compacted tailings, thus reducing oxygen supply in waste rock by preventing thermal air convection and minimizing oxygen advection and diffusion.

Jan 1, 2000

By Richardo Montoya

Radomiro Tomic, the new CODELCO division, is a copper deposit located at 3000 m a.s.l. and 40 Km from Calama in northern Chile. It has total oxide reserves of 802,000,000 tonnes with an average grade of 0.59% total Cu (using a cut-off grade of 0.4% total Cu). The copper oxide ore is mainly atacamite and chrysocolla. Startup is expected to commence in December 1997 of 150,000 t/y of Cu cathodes. Future expansion to 250,000 t/a of Cu cathodes is currently being planned. The process consists of an open-pit mine, a two-stage crushing system, agglomeration with sulphuric acid and emplacement on a heap leach pad for a 45-day leaching cycle. Solvent extraction and electrowinning will produce LME "A grade cathode. A number of significant technology innovations have been incorporated into the project.

Jan 1, 1998

By H. M. von Seebach, M. P. Trubeljal, L. G. Austin

Six US coals and a crystalline quartz were tested in an instrumented laboratory high-pressure grinding rolls machine equipped with 100-mm-diam. rolls. The machine was choke-fed to maximize the capacity. As expected, the specific capacity decreased with increased grinding pressure for each material tested. Among the six coals, there were significant differences in the critical angle of nip, the effective feed porosity and the variation of strain at the gap relative to the grinding pressure. Although a precise correlation was not obtained, the overall effect of these factors was that, at a given grinding pressure, the specific capacity increased as the Hardgrove grindability index of the coal increased. The relationship between the specific capacity and the grinding pressure for a given coal was independent of feed size down to 150 µm. However, smaller feed sizes produced anomalous results, and the flow within the feed hopper was restricted.

Jan 1, 1996

By D. R. Maneval

The vast coal resources of North Slope, Alaska, can be expected to attract substantial interest because the nearly flat-lying coal beds of the coastal plain are specially amenable to surface mining. Mining on a scale large enough to justify coal development in this area could have severe environmental effects. The mitigation would be uncertain because large-scale coal mining and reclamation operations have not been carried out in the arctic. The deficiency of the scientific data base is another factor that requires consideration if coal mining has to develop in accordance with the objectives of PL 95-87. The objective of this paper is to establish the inter-relationship between the problems due to permafrost and factors in reclamation of post-mining land in order to find ways to transform nature in a rational and purposeful manner and to suggest specific reclamation approaches that may be appropriate in this region.

Jan 1, 1987

By J. Rostami, P. P. Nelson, A. Khetwaln

Tunnel boring machines (TBMs) can be considered as the method of choice for tunneling in many projects due to the high level of efficiency and high potential productivity, safety, and applicability in a variety of subsurface conditions. The muck transportation system in a TBM tunneling operation plays a significant role in the process and impacts the overall performance of the machine. This paper introduces a recently developed method of simulating TBM operation through discrete event simulation (DES), which allows for tracking of the various activities, incurred downtimes in the operations, and overall machine utilization. The study presented here compares two different muck transportation systems, conveyor and rail, under similar geological conditions to quantify the impacts of the choice of muck transportation systems on machine utilization. The results show the applicability and extent of redundancy in the use of the two systems relative to machine capabilities and their sensitivity to geological conditions.

Jun 13, 2021

By V. Steinbach

Non-renewable mineral raw materials are grouped into three categories to investigate ways leading to sustainable use of natural resources: 1.) metallic resources, 2.) non-metallic resources with the exception of the fertilizer minerals, and 3) the fertilizer minerals for the nutrients nitrogen (N), potassium (K), and phosphorous (P). With the exception of minerals in Group 3 which are essential for plant growth, mankind does not need raw materials as such, only the intrinsic property of a material that fulfils a useful function. This is especially true for non-metallic materials. Metallic resources have the best chance to become renewable if one makes optimal use of the resources of the man-made technosphere. For the fertilizer elements K and N there does not exist a problem, because sea water or air respectively provide an inexhaustible source for them. This does not apply to P however. So P is serving as one of our apposite case studies for solving sustainability challenges. For all the challenges along the road from a non-sustainable to a sustainable resource economy technology can be envisioned to come to the rescue provided conditions that are considered to be essential for sustainable use for all natural resources-- affordable renewable energy and human ingenuity to find new solutions for functions, to optimize processes and to minimize losses-- are satisfied.

Jan 1, 2011

By B. Das, B. K. Mohapatra, K. S. Narasimhan, S. K. Bhaumik

The iron ore slimes (d80 ~ 50 µm) generated at Noamundi iron ore washing plant (TISCO), assaying 57% Fe, 4% Si02 and 8.3% A1203, have been subjected to hydrocyclone studies. The effects of different design and operating parameters have been studied to get a product suitable for subsequent use in the sinter mix. The studies indicate that it is possible to obtain a product containing 64% Fe, 1.4% Si02 and 3.5% A1203 with a recovery of 49% iron. The process involves classification followed by separation in a hydrocyclone. By this method, the overall yield of iron ore production in the plant is expected to increase by 8%. Microscopic examinations and X-ray diffraction studies were conducted to elucidate the mineralogy and liberation characteristics of Noamundi iron ore slimes. This paper deals with the findings of the investigations.

Jan 1, 1993

By DeVerle P. Harris

The structure of an exploration model reflects a number of design considerations, one of which is the question or issue-to be investigated by the model. Thus, a model designed to evaluate the magnitude of risk and its economic implication to optimal decision making at each decision juncture of a multistage exploration architecture differs considerably from one designed to evaluate, say, the long run average cost of discovery, in which the architecture of exploration is suppressed and risk is simply an element of average cost. The perspective of the model examined in this paper is that exploration is investment in (purchase of) information and that the next stage of an exploration program is undertaken only when the expected value of information to be acquired in that stage exceeds its cost. The degree to which this perspective is honored influences considerably model design. Consider two design objectives:

Jan 1, 1989

By T. W. Camm, J. C. Johnson

"Most engineers are bright, hard-working, reliable, and prefer to avoid conflict. An engineering curriculum tends to self-select these characteristics. By most standards, you would expect workers exhibiting these traits to require minimal supervision. But is this true? Is this how most current engineering managers lead? Looking at some current theories on leadership combined with personal anecdotes, this presentation will look at some common misconceptions about leading engineers. INTRODUCTION Engineers are different. There, I said it. From cartoons to movies to television shows and more, there is a reason stereotypes of engineers resonate. Yes, you can find a lot individual variation among specific engineers that you may know, but they do not detract from some of the overarching commonalities that engineers are known for. CLASH OF CULTURES What distinguishes a professional? Raelin (1985), in his book Clash of Cultures, describes professionals as having superior intellectual training, maintaining their own standards of excellence, and being supported by associations that maintain the quality of the profession. Engineers obviously fit all three of these ideas: an engineering degree is still regarded as one of the most difficult to attain; we maintain our own standards both through peer-review and in academia through ABET accreditation; and through professional associations like SME to promote the discipline and foster technical growth. Six characteristics representing professional status are described by Raelin (1985, p. 9): Expertise—prolonged specialized training in a body of abstract knowledge. Autonomy—the freedom to choose the means to solving a problem. Commitment—Primary interest is in pursuing the practice of one’s own chosen specialty. Identification—identifying with the profession and with fellow professionals, both through formal associations and through peers external to the organization. Ethics—providing service without concern for oneself or without becoming emotionally involved with the client. Standards—committed to help in policing the conduct of fellow professionals. Engineers are smart—in the vast majority of cases they are hired specifically for their expertise. At a typical mine the ventilation engineer knows more about mine ventilation than anyone else on site; the same is true for the rock mechanics engineer, the explosives engineer, the planning engineer who uses sophisticated computer software—each is the expert for their particular area at the mine, that is why they have that responsibility. This can present a dilemma for the manager for each (sometimes all) of these engineers. The manager needs to keep everyone on task and focused on the objectives of the organization. Because they have reached their position by following the norms and expectations of the organization, managers tend to have a certain amount of loyalty to that organization. Engineers, on the other hand, tend to have mixed loyalties, having as much loyalty and affinity for their profession as they do for the particular company they happen to be working for at any given time. This dynamic can often lead to power struggles between the managers, based on their positional authority in the organization, and the engineers, based on their specialized knowledge (Camm, 2013)."

Jan 1, 2017

By C. Zhou, B. Whisner, J. Carr

Proximity Detection Systems (PDSs) are used in the mining industry for protecting mine workers from striking, pinning, and crushing injuries when they work in close proximity to heavy machines such as continuous mining machines (CMMs). Currently all Mine Safety and Health Administration (MSHA) approved PDSs are magnetic field based systems which can be influenced by the presence of wire mesh that is commonly used for supporting roof and ribs in underground coal m ines. In this paper, researchers at the National Institute for Occupational Safety and Health (NIOSH) characterize the influence of the mesh on the performance of magnetic PDSs by measuring the magnetic field difference around a CMM caused by the presence of the mesh. The results show that the magnetic fields are generally enhanced by the mesh which causes the PDS detection zones to be increased correspondingly. It was discovered that the fields around the joints of two mesh sections have the greatest enhancement and thus deserve more attention. In addition, it is found that the presence of mesh can also cause a variation in the generator current. The influence of mesh is characterized by the change in the generator current with respect to the distance between the generator and the mesh. It was found that the generator current change caused by the mesh can be significant (on the order of ten) when the mesh is extremely close to the generator (e.g, less than 1 cm) and is negligible when mesh is relatively far (greater than 0.15 m). The findings in this paper can be used to develop guidelines and best practices to mitigate the influence of mesh on PDSs. INTRODUCTION The Mine Safety and Health Administration (MSHA) requires operators of underground coal mines to equip place-changing continuous mining machines (CMMs) with proximity detection systems (PDSs) to protect mine workers from striking, pinning and crushing injuries when they work around these heavy machines. Although a variety of technologies can be implemented for proximity detection, the magnetic-field-based PDS that was originally developed at the National Institute for Occupational Safety and Health (NIOSH) has shown great effectiveness in challenging mining environments and currently all MSHA-approved PDSs are magnetic-field-based systems. As shown in Figure 1, a magnetic PDS typically includes two major components----the magnetic field generator and the Miner Wearable Component (MWC). Magnetic fields are generated by injecting a high electric current into a ferrite-rod antenna sealed in the generator. The magnetic field strength detected by an MWC varies with the distance between the MWC and the generator. In a typical PDS, multiple generators are mounted on different locations of the machine. The relative location/zone of an MWC is determined based on the field strengths from different generators picked by the MWC. Ideally, for a PDS to work properly in the underground, the magnetic fields generated by the different generators should be stable and not vary with the environment, as the system would interpret any variation of the magnetic field as a result of the distance change between the machine and the miner wearing the MWC. In reality, however, this is not always the case since magnetic fields can be altered by a number of environmental factors such as the presence of steel wire mesh that has been widely used in underground coal mines for supporting roof and ribs In this paper, the influence of mesh on the PDS performance is investigated and the magnetic field change caused by the mesh is measured.

Jan 1, 2019

By E. Zahl, J. Whyatt, H. Lawson

The U.S. Mine Safety and Health Administration (MSHA) issued Program Information Bulletin P09-03 in April 2008, providing formal guidance on using programs that model the redistribution of stress during underground mining of coal. A key part of this guidance is visual observation and mapping of ground conditions. If a correlation between ground conditions and model output can be established, the model is considered to be verified, and can be used to guide mine design in similar ground. A simple scale is recommended for ranking observed roof, rib and floor conditions. This paper discusses optimization and implementation of a ground condition rating scheme in the gateroads of a deep underground longwall coal mine. Roughly 80% of each gateroad length deteriorated in a fairly uniform manner. However, this manner varied between gateroads, as did pillar size. The implementation of a ground condition mapping program, similar to that recommended in PIB P09-03, was successful in characterizing the ground response to mining in gateroads of a longwall coal mine.

Jan 1, 2013

By F. F. Peng

A unique collector dispersion techniques was developed and used to improve the flotation rate and recovery of coarser and ultrafine coal-rich particles in the froth flotation processes. In this novel collector dispersion method, the collector such as hydrocarbon-oil is gasified and transported by gas phase (air stream) into the pulp. In addition to the excellent mode of collector dispersion, the collector-encapsulated air bubbles are generated in the pulp. This approach alters the surface properties of air bubbles and provides the fast rate of flotation compared to that of direct liquid collector addition froth flotation. Using gasified kerosene as the collector, the effect of altering surface properties of bubbles on the recovery of larger and finer coal-rich particles of -1.7 mm (-12 mesh) and -600 µ m (-30 mesh) raw coal samples were studied. The Redstone seam coal obtained from Northern Central region of West Virginia was used in this work. The effect of particle size on oil-coated bubble flotation rate and recovery were also evaluated. The conventional froth flotation test with a liquid form of kerosene addition was also conducted for comparison purpose.

Jan 1, 1991

By Morgan M. Sears

The stability of gateroad pillars is crucial in deep-cover longwall mining, especially during transitions to wider panel layouts. This study evaluates the transition from a 700-foot to a 1,000-foot panel layout with an inter-panel barrier in a deep-cover longwall mine in Southwestern Virginia to identify a configuration that enhances stability and reduces operational risks. Using the LaModel program, three pillar configurations were simulated to assess their performance based on stress distributions and pillar safety factors. These included the previously used 4-Entry Yield-Abutment-Yield layout, the current 3-Entry Yield-Abutment layout with a 220-ft inter-panel barrier, and the proposed 3-Entry Yield-Yield layout with a 320-ft inter-panel barrier. The findings of this study suggest that the proposed 3-Entry Yield-Yield pillar layout is more effective in managing stresses in deep-cover mining environments. By optimizing pillar placement and improving load management, this layout could positively impact mineworker safety and health. The study underscores the importance of advanced simulation tools in developing innovative solutions to address the challenges of modern longwall mining operations.

Feb 1, 2025

By R. V. Ramani

Minerals, together with agricultural and forestry products, are the primary source of wealth produced in the United States. Although the production of minerals requires only a small fraction of the state's total land surface, as compared with either agriculture or forestry (Table 1), mining activities generally are much more disruptive to the land surface, and rehabilitation is more complex and costly. The past 10 to 15 years have witnessed a sharp increase in mineral exploration and mining, particularly coal mining, which has brought with it an increase in conflict over land use and an increase in negotiations for purposes of mineral prospecting and mining. The general increase in the production and consumption of coal and the particular increase in the percentage of coal extracted by surface mining methods coupled with a growing nationwide environmental consciousness have created increased public concern and in some cases outrage over mining activities. Although there is ample evidence to indicate that it is possible to plan for and design mining activities in such a way that they are compatible with other activities and can thus be made a part of a sequential land-use plan, there is a general lack of knowledge regarding the importance of mining as the provider of basic and essential raw materials to supply society's constantly expanding and increasing mineral needs. This lack of knowledge extends to such matters as land and mineral rights negotiations, the character of mineral deposits and minerals, mineral economics, and land-use planning.

Jan 1, 1977

By Ehsan Moosavi, Kamyar Tolouei

In open-pit mines, the long-term production scheduling optimization problem (LTPSOP) is a complicated problem that contains constraints, large datasets and uncertainties. Due to its dimensions and NP-hard nature, it is usually difficult to find an ideal solution to the LTPSOP. The optimal schedule generally restricts the ore, metal and waste tonnages, average grades, and cash flows of each period. In this paper, to synthesize grade uncertainty into the strategic schedule, a stochastic integer programming (SIP) framework is presented to LTPSOP. The objective function of the SIP model is to maximize the net present value and minimize the risk of deviation from the production targets considering grade uncertainty simultaneously while satisfying all technical constraints and operational requirements. Instead of applying one estimated orebody model as input to optimize the production schedule, a set of equally probable orebody realizations is applied to synthesize grade uncertainty in the strategic schedule and produce a more profitable and riskbased production schedule. To solve the LTPSOP, the hybrid approach with the augmented Lagrangian relaxation method, the Harris Hawks optimization, the Random Forest method and Monte Carlo method was proposed. To indicate the applicability of the model, a case study on a gold mine was implemented. The framework displays the capability to minimize risk and improvement in the expected net present value and financial profitability .

Jun 25, 2023

By J. W. Sweeney

The .Florida land-pebble mining industry of central Florida was examined to identify trends in land use; conflicts in land use; and the effect of the conflicts on mineral resources. Many conflicts exist in the study area, such as conflicts with other users of land resources and land surface; conflicts with high revenue land users; conflicts for land surface in urban and suburban areas; and conflicting restrictions concerning utilization. Projections are made showing that lands in phosphate company ownership are expected to be made available to help meet the need for future urban expansion in the study area. Some phosphate resources have been lost due to land use conflicts, however, most of the resource loss has been small. Land use conflicts and phosphate mining are reconcilable and considerable progress toward their maximum and multiple use of land and mineral resources can be resolved through farsighted planning based on factual data.

Jan 1, 1972

By Lawson. Heather

"The purpose of this study is to explore how the geochemical and petrographic components of coal may impact its physical properties, as well as how these components correlate with a history of reportable dynamic failure in coal mines. Dynamic failure events, also termed bumps, bounces, or bursts, are the explosive failures of rock in a mining environment. These events occur suddenly and often with no warning, resulting in worker injury up to and including fatality in greater than 60% of MSHA reportable cases. A database of variables was compiled using publicly available datasets, which included compositional geographic, strength, and Hardgrove Grindability Index (HGI) data (ACARP, 1998). Results indicate that bumping coals are less mature, lower in carbon, higher in oxygen, softer, and less well cleated than coals that do not bump. High liptinite content was found to correlate with higher average UCS values. However, no clear, direct correlation between UCS and dynamic failure status was observed. The findings of this study establish that differences exist between coals that have experienced reportable dynamic failure accidents versus those that have not. These differences are inherent to the coal itself, independent of mining-induced risk factors. Results further illuminate how compositional attributes of coal influence physical properties and begin to clarify potential links between geochemistry and dynamic failure status. Only through the better understanding of risk can more effective mitigating strategies be enacted.INTRODUCTIONDynamic failure events, also termed bumps, bounces, or bursts, are the sudden failures of rock in a mining or quarrying environment. Failure occurs when the rock’s critical bearing capacity has been exceeded and the rock fails energetically through the outward expulsion of rubblized material (Peng, 2008). These events occur suddenly and often with no warning, resulting in worker injury up to and including fatality in greater than 60% of reported cases through the Mine Safety and Health Administration (MSHA). Much research has been devoted to the prevention of these events. The effects of overburden depth and stiffness, mine design, mining practices, and in situ stresses are well documented (Agapito and Goodrich, 2000; Brauner, 1994; Campoli and Kertis, 1987; Holland and Thomas, 1954; Iannacchione and Zelanko, 1995; Lawson et al., 2016b; Mark, 2016; Newman, 2002; Peng, 2008; Whyatt, 2008). Despite these significant advancements in coal mine ground control, however, events continue to occur. Proactive risk mitigation remains an important research area. This is particularly true in underground coal settings, where the rockmass is layered, lithologically diverse, and does not exhibit consistent material properties across deposits.Many conditions have been associated with the occurrence of dynamic failure phenomena, including:"

Jan 1, 2019

By David L. Martin

This paper discusses the development of a SLAM II* simulation model with imbedded optimization modules designed M evaluate mineral exploration and exploitation strategies. The model traces through a sequential exploration program, evaluating each deposit site based upon geologic information and potential profitability of the site. At a specified time during the simulation, a new production plan is developed for currently producing deposits which takes into account the planning horizon and deposits which are currently being explored. Potential uses of the model by geologists, engineers, and management decision makers include setting corporate objectives and policies on exploration and production. The model is also useful for testing past decisions to evaluate decision making criteria and evaluating mineral deposit profit potential.

Jan 1, 1983

To generate a most profitable ultimate pit limit is generally the first step in mine design. This paper presents a new graph theory oriented, optimum ultimate pit limit design algorithm which will maximize the total undiscounted net profit. This algorithm performs much better than the well known Lerchs-Grossmann algorithm, in terms of the reduction in computation time and computer memory requirements. This algorithm operates on many directed trees in a graph, where each vertex in a tree represents a block in the mine model. The formation of each directed tree is based more on the ore-waste support concept than the geometry constraints alone. The general procedures of the algorithm, programming considerations and two case study results are discussed in the paper.

Jan 1, 1990