Search Documents

By Evan Adams

The Ireland Mine is located some seven miles South of Moundsville West Virginia, along the bank of the Ohio River. We are mining the Pittsburgh #8 seam. This seam is approximately 60" in thickness, and is immediately overlain by some 10 feet of a conglommerate material. The roof is difficult to control, due to the fact that it frequently is composed of substances not hard enough to be held together with 6-foot roof bolts. In many cases, we must use 10-foot roof bolts, in order to get bolt anchorage in the limestone above the conglommerate. Due to the elasticity of the limestone and its tendency to bend rather than to break, we have been unable to maintain a pillar line. Thus, we have found it necessary to mine by the room and pillar system. Belt haulage is used on room entries to automatic loading stations, thence into 15-ton mine cars, controlled at the loading point by car spotters. The maximum belt length is 2,000 feet. Rail haulage to the slope-bottom dump is by 27- and 50-ton locomotives. The mine produces coal two shifts per day, with 7 production crews on each shift. Mine and machinery maintenance is performed on the Midnight shift. We handle an average of 660 tons per machine shift.

Jan 1, 1964

By D. W. Agers

This paper is an extension of previous work evaluating a new extractant, LIX®-64, for recovery of copper from dilute acidic solutions. Large scale pilot plant operations have confirmed the technical and economic feasibility of the process and, with minor exceptions, scale up parameters obtained by previous laboratory work. Operating problems encountered in the pilot plants are discussed. Design parameters for-scale-up to commercial plants are presented and discussed along with a revised capital cost estimate. The future pilot program is discussed, including minor design changes and the effect of entrained organic on dump leaching efficiency.

Jan 1, 1967

By Ralph W. Barbaro

This paper presents a cyclic queueing model which evaluates the productivity of a shovel-truck materials haulage system. For a cyclic queueing problem with exponentially distributed service times, a cyclic queueing model provides exact solutions in a fraction of the time that simulation takes to produce an approximate solution. The model is applied to an example problem, and the results are validated with simulation. Simulation is used to show that the assumptions of exponentially distributed service times and steady-state are not serious problems. A cyclic queueing model can be used to quickly obtain an accurate assessment of the productivity of a shovel-truck system.

Jan 1, 1986

By T. M. Klemetti, T. J. Batchler, T. J. Matthews

"From 2011–2016 there were 1,511 documented injures, including 7 fatalities, from ground falls in U.S. underground coal mines. The majority of these ground fall injuries were not caused by a major roof collapse, but from falls of smaller rocks from the immediate roof. Roof screen can significantly reduce the number of these injuries and has been widely utilized in underground coal mines for surface control. Because of the potential of reducing ground-fall injuries, the National Institute for Occupational Safety and Health (NIOSH) is further evaluating the performance characteristics of welded wire screen as used in underground coal mines by conducting a laboratory testing program at the Mine Roof Simulator (MRS) in Pittsburgh, PA. The load-displacement characteristics of a 2.4-m x 3.7-m panel of 8-gauge welded screen were evaluated using a newly designed, large laboratory screen test frame with multiple load pull locations. This screen was tested in a configuration that simulates current installation practices in U.S. coal mines. In this study, the effects of displacement loading rate, load pull surface geometry, and the inclusion of roof channel on the screen performance were evaluated. Ultimately, the type of information obtained in this and similar studies can be used to aid in developing wire roof screen design criteria and to assist mine operators in the selection and use of roof screen in underground mines. INTRODUCTION Over 1,500 injures, including 7 fatalities, occurred from 2011–2016 from ground falls in U.S. underground mines with the majority of these ground-fall injuries caused by falls of smaller rocks from the immediate roof. Various controls are currently being used in mines to control this surface rock, including the use of wire roof screen. In mines where wire roof screen has been installed, injuries from rock falls have been reduced dramatically (Robertson and Hinshaw, 2001). Roof screen has the potential to prevent hundreds of injuries caused by the fall of small rocks between permanent roof supports (Comptonet al., 2007). Because of this potential for reducing ground-fall injuries, the National Institute for Occupational Safety and Health (NIOSH) is evaluating the performance characteristics of welded wire screen as used in underground coal mines by conducting a laboratory testing program at the Pittsburgh Research Laboratory (PRL)."

Jan 1, 2018

By Yiming Sun, David Tsztoo, Rick Nolting, Adam M. Wirthlin, Rebecca Fusee

"Excavation and initial support of the New Irvington Tunnel presented significant challenges, including rapidly changing ground conditions, heavy ground loads, and squeezing. Such behaviors were anticipated from historic tunneling records of the adjacent Existing Irvington Tunnel, and extensive site investigation, but clearer understanding of their actual extent and causes has resulted from convergence measurements, observations of ground behavior, initial support monitoring and detailed geologic mapping. Time-dependent movements, documented hours to months after excavation in clay-rich rock and in moderately to intensely fractured rock, identified squeezing areas, allowed classification by currently-used predictive methods and added to the list of lessons learned in tunneling such ground. INTRODUCTION In March 2003 the San Francisco Public Utilities Commission (SFPUC) authorized funding for the $4.6 billion Water System Improvement Program (WSIP) to repair, replace, and seismically upgrade its water system. The program consists of 35 local projects located within San Francisco and 48 regional projects located in several counties from the Sierra foothills to the San Francisco Bay Area. The New Irvington Tunnel (NIT), a key component of the WSIP, is located east of Fremont in Alameda County, on the east side of San Francisco Bay. The NIT is a new 18,660 foot (5,689 m), redundant tunnel, 190 to 670 feet (58–204 m) offset from, and subparallel to the Existing Irvington Tunnel (EIT). Built between 1928 and 1932, the EIT was constructed with an unreinforced cast-in-place concrete lining and is vulnerable to damage in the event of a major earthquake along the two closest active faults. The Hayward Fault is located less than a mile west of the tunnel, and the Calaveras Fault is located half a mile east of the tunnel. Although the alignment does not intersect these faults, the shaking and sympathetic displacement along secondary faults that cross the tunnel alignment are potential hazards. The NIT provides a seismically reliable water transmission facility capable of withstanding earthquake damage and maintaining continuous water service after a major earthquake. The NIT also adds system redundancy and provides for operation flexibility of running water through both tunnels, or through one tunnel while the other is out of service for inspections and maintenance."

Jan 1, 2016

By M Aboagye, K Appau, W. Assibey-Bonsu, C. Muller

A case study based on two recoverable resource modelling techniques (indirect and direct or localised methods) have been derived using typical feasibility study or new mine drilling data configurations from the extensions of an existing mine’s massive production database. The database is from the Gold Fields Tarkwa Gold mine (~6Moz Mineral Reserves and 13-year Life-of mine). The corresponding recoverable resources from the various techniques are then analysed using the open pit Whittle optimisation process. The results were then compared based on the Whittle optimisation results to determine the efficiencies of the approaches and the validity of the recoverable mineral resource estimates for mine planning and financial forecasts (including Cash Flows etc). Based on historical production metal recovery, the paper also assesses the corresponding orebody and mine planning as well as financial risks with regards to the modelling techniques. The study shows that the localized direct and somewhat more straight forward approach if applied efficiently can provide an equally useful tool for computing recoverable resources for mine planning and financial forecasts, as compared to the indirect approach as presently in use.

Jun 25, 2023

By William K. Brown

Are the results of an exploration program worth the cost? This is a question I suspect many of you are familiar with and, theoretically at least, it is an easy question to answer. The answer, of course, lies in comparing the future earnings stream the program is expected to generate, to the present value of the cost of carrying it out. While historical costs can be determined without much difficulty, estimating the value of a future earnings stream involves all sorts of assumptions regarding future costs, metal prices, inflation rates and an appropriate discount factor; and in the context in which the question arises, requires additional assumptions about mineral deposits which have yet to be discovered. As a practical matter, this kind of approach isn't likely to produce a very convincing answer; certainly not one convincing enough to satisfy a skeptical audience; nor one likely to temper the illusions of recent converts to mineral exploration, who are convinced that if enough money is spent, profitable discoveries will inevitably follow. Within broad limits, however, I believe it is possible to analyze the costs and results of gold exploration in the U.S.A. over the past 20 odd years in a useful manner. And while such an analysis is imperfect, it will provide some insight into this fascinating subject.

Jan 1, 1983

By G. Blackwell

In the 1980's the Canadian surface mining industry was confronted by declining competitiveness in the face of low cost foreign producers and alternative materials. Low metal prices undermined profits for many mining companies. Restructuring, rationalization, capacity reduction, technology transfer, as well as favourable currency rates and higher commodity prices, helped revitalize the industry by the close of the decade. Now in the 1990's, however, the need to improve competitiveness for profitability has re-emerged in greater intensity. In the current climate it is considered that there are three strategies available to industry to ensure profitability: continued rationalization and restructuring; optimization of operating practice; and technology development and transfer.

Jan 1, 1993

By D. H. Dvorak

Two pilot-scale biological reactor systems were installed to treat metal-contaminated water. The reactors consisted of barrels and tanks filled with spent mushroom compost, within which bacterial sulfate reduction became established. Concentrations of Fe, Zn, Mn, Ni, and Cd were lowered by over 95% as these metals were precipitated as insoluble sulfides by reaction with bacterially generated H2S. The chemistry of the reactor systems is examined, and opportunities for maximizing their metal-retaining and alkalinity-generating potentials are discussed.

Jan 1, 1991

By L. K. Lepley

A marine sonic sub-bottom profiling system and a hovercraft were used in an engineering geophysics survey of the tailings being deposited at the Mercur gold mine. Detailed density sections with vertical resolution of one meter were desired for computations of strength, permeability and potential self-compaction. The logistical problems of conducting a geophysical survey and in collection of geotechnical soil samples from an active tailing impoundment was solved by using the amphibious hovercraft for towing and transport on the impoundment. The "chirp" sonic system produced continuous, real-time geophysical cross-sections with vertical resolution of ten centimeters showing possible trapped gas. The hovercraft provided a platform over water, ice, slurry, and solid beach for collection of geotechnical information and physical samples.

Jan 1, 1994

"The Industrial Comminution Efficiency (ICE) working group, part of the Global Mining Standards and Guidelines Group (GMSG) has engaged a large number of industry professionals representing mining companies, equipment vendors, consultants and metallurgical laboratories with interests and capabilities in the comminution field. These participants have collaborated to develop three guidelines for the assessment of the efficiency of mineral comminution circuits. Two of these guidelines deal specifically with power based modelling techniques to quantify energy efficiency using widely practiced techniques, those developed by Bond (1961), Rowland and McIvor (2009), and Morrell (2009). The third guideline deals with the sampling and surveying of grinding circuits as is required to provide the necessary information, at appropriate quality, to furnish the efficiency analysis promoted by the first two guidelines. This preprint will focus on the Guideline on Methods to Survey and Sample Grinding Circuits, which is currently in the final stages of peer review and finalization by the GMSG. INTRODUCTION It is important to make a clear distinction on the scope of work of the GMSG guideline for sampling grinding circuits. Many mineral processing practitioners are familiar with the sampling and surveying of comminution circuits, in particular grinding circuits, for performance diagnosis and the identification of optimization potential. These surveys often provide information for population balance modelling of individual comminution and classification unit processes, and as a result require a large amount of information to calibrate and validate the unit models. As a result these surveys are labour intensive, somewhat expensive depending on internal capabilities of the mine site or company, and have a long time span from initial planning to final reporting. They also require a high level of expertise to process the survey data, simulate the circuit and make sensible recommendations on follow up actions. As a result of these factors full grinding circuit surveys are not a common occurrence at a large number of facilities, and several years may pass before follow up surveys are conducted. In the ensuing gap between surveys, the efficiency of the grinding circuit must often be taken on faith, and this is considered an unacceptable lapse in an environment of strained natural resources and low commodity prices. To support the rapid and productive energy efficiency analysis being promoted by the ICE working group, a much simplified survey and analysis process is required. The process reflected in the GMSG guideline is indeed more conducive to frequent analysis, at a skill level that is well within the capabilities of the average plant metallurgist. As a result it becomes feasible to conduct mini-surveys of plant performance, which can be used to quickly and precisely diagnose the high level impact of process changes. It can also be manipulated by experienced practitioner to provide sufficient information for modelling of the circuit to estimate the impact of process changes, supporting an initial rate and rank exercise to focus plant optimization efforts."

Jan 1, 2016

By K. Biswas

For the pillars, which have been standing long after mining, the stability depends much on the weathering action in the presence of mine moisture. From the field observations, it has been found that this weathering action becomes critical in terms of pillar stability if the coal seam contains partings or binders in it. The weathering action degrades both the partings and coal in terms of their load bearing capacity as the mine moisture penetrates into them. This paper investigates the effect of weathering action on coal and partings in the laboratory. In the field, the strength profile in the coal and the partings and the effect of time (in terms of the pillar age) on them have been studied by using borehole penetrometer. In this paper, an attempt has also been made to establish formulae for time dependent strength of coal and partings.

Jan 1, 1997

By R. Wu, R. Howell, J. Dase

Turquoise Ridge is an underground gold mine located in the Potosi Mining District, approximately 64 km northeast of Winnemucca, Nevada. Turquoise Ridge Underground is accessed via two shafts and a system of internal ramps and utilizes underhand drift and fill mining methods with cemented rockfill. The mine also employs mechanical mining as well as sill benching as mining methods. Ground conditions at Turquoise Ridge Underground are poor, and the Rock Mass Rating (RMR) may be less than 20, or very poor, in ore headings. Current production rate is 2,700 tonnes of ore per day. Key challenges in increasing production levels and reducing costs are the development of sufficient stoping areas and the transition from top-cut development to undercut stoping. Completion of the infrastructure development in the North Zone is necessary to achieve and optimize higher production levels. The #3 Shaft project is well underway and is expected to be commissioned in mid. 2022. The shaft will drastically decrease the haulage requirements in the North Zone

Mar 2, 2022

By John A. Rajala

The water chemistry of the froth flotation pulp is one of many parameters which can affect the flotation process. The fluid may contain certain inorganic salts which, along with increased ionic strength, can produce undesirable flotation depression or activation. A source of a salt could be the use of calcium chloride to prevent freezing in ore cars, chutes, and bins (Anon., 1980). Alternately, the salt or salts could be initially contained in the water as in the case of sea water and some brackish waters. These salts may become more concentrated because of the need for recycling of plant water due to environmental regulations and/or economic considerations (Davis, F.T., et. al., 1976). The presence of inorganic salts in flotation pulps and their effects upon the recoveries and surface chemistries of different oxide minerals have been the object of various studies. Some researchers (Fuerstenau, D. W. and Raghavan, 1976; Fuerstenau, D. W. and Modi, H. J. 1960; Kulkarni, R. D. and Somasundaran, P., 1977) have reported that addition of a salt can increase or decrease flotation recovery depending upon the particular system.

Jan 1, 1982

By A. Benchekroun

The phosphate mining industry is confronted everywhere in the world with financial difficulties and low prices which prohibit further investments and development of new mines even in regions with a comparative cost advantage (North America/ North Africa/ and Middle East). But old mines are being progressively exhausted/ and if no replacement mines come on stream in the near future/ we may soon find ourselves (around the year 2000) with a global annual production capacity of 160 million tonnes of marketable phosphate rock instead of the capacity of 200 million tonnes existing today. Unless prices improve/ phosphate rock/ a non-renewable resource and a vital commodity to world agriculture/ may turn to be in short supply to world fertilizer industry. Whatever the extent of recovery of fertilizer demand/ the expected decline of the production capacity during the 1990 I s is bound to cause the disappearance by the year 2000 of the important surplus characterizing today the supply/demand balance.

Jan 1, 1995

By Péter Siklósi, János Zámbó, Károly Solymár

It is fundamentally important to evaluate bauxites in a realistic, commercial way on the basis of the processing technology both for the supply of existing alumina plants and for the designing of new ones. The evaluation system developped by ALUTERV-FKI consists of chemical, mineralogical, texture and technological testing. The commercial value of bauxites is basically determined by their available alumina content and the caustic soda consumption required for their processing. However, their contaminants have to be taken into consideration, too. The commercial value of bauxites also depends on the processing technology and their possibly unfavourable chemical and mineralogical composition can be /at least partially/ compensated by R&D efforts. The selection of the optimum processing technology and the effects of further developing the same are demonstrated on monohydrate bauxites containing goethite and carbonates. Some of the technological solutions /desilication or deironing of bauxites, hydrothermal treatment of the digestion residue / make at the same time possible the complex processing of the bauxites, the profitable utilization of their main components.

Jan 1, 1984

? World industrialization, increased urbanization, and population growth are driving a sustained demand for minerals, metals and coal. Energy demand is expected to increase significantly in the coming decades - placing even more emphasis on supply, security and environmental impact issues. ? Several countries are taking steps to nationalize their own resources thus safeguarding their supplies and reducing exports of natural resources. ? Understanding the future availability of critical minerals requires a global perspective. It is essential to know where deposits are located, their reserves and resources, the technologies necessary for production, and the costs of producing and transporting the products to consumers. ? As mining companies look to maintain or increase their operating capabilities and increase their mineral resource bases, the search for commodities expands beyond developed terrestrial regions of the world, to include marine resources. (Figure 1) Operating challenges in these locations include finding skilled workers, building infrastructure, improving recovery technologies and practicing sustainable development.

Jan 1, 2011

One of the most challenging and ambitious dump rehabilitation projects in South Africa’s mining industry is being carried out at Greenside Colliery’s smoldering coal dump, which lies adjacent to the N 12 Johannesburg-Witbank highway. Greenside Colliery is the largest coal mine in the Gold Fields Group. It began operation in 1946, the year in which the burning dump had its origins. Today, Gold Fields plans to spend R16 million (about $USS8 million) to encapsulate the dump, bringing it into compliance with South Africa’s Mining Environmental Management Programme, according to Martin Hamer, engineering manager of the Greenside Colliery. The improved environmental management approach will result in reduced sulfur dioxide gas, smoke and dust emisson into the air and an enhanced aesthetic appearance of the dump from the N 12 highway. The objectives of the project are to place and compact coal discard to within the National Institute of Coal Research specifications in order to prevent spontaneous combustion, and to preserve as an asset the coal portion of the discard.

Jan 1, 1994

By Lane White

Loading shovels are at the heart of most surface mine production. As truck sizes have increased, shovel manufacturers have matched them with larger shovels (see table, page 343). Further increases in shovel size may be in order if trucks in the 270-t (300-st) range find acceptance at the largest surface mines. However, larger shovels are not currently the primary focus of shovel design engineers. Competition and user pressure are combining to keep their work directed toward improved shovel productivity and efficiency. Computer design technology and advanced electronics play an increasingly prominent role in this work. "Improved diagnostic capability, system monitoring, vibration analysis and above all increased user friendliness in machine control systems are being pursued by most manufacturers working in our industry today," observes Stuart R. Cotterill, director of marketing for Harnischfeger Corp. The use of computer-aided design (CAD) systems in shovel design has been in place for many years. However, recent advances in computer capability and improved software programs and graphics are making computers even more useful.

Jan 1, 1995

In his keynote address at the 18th International Minerals Processing Conference (IMPC), R.P. King, director of the University of Utah Comminution Center, said "it will be the application of very fundamental physical principles that is likely to bring major advances in comminution technology (IMPC, pp. 39-45)." It is evident from the literature published in 1993 that many of these fundamental studies, particularly as they relate to single-particle fracture mechanics and mineral liberation, are starting to bear fruit. The beginnings of fundamental mathematical models for design, scale-up and control of comminution systems are now taking shape. Modeling/fundamentals Population balance models (PBM) have been used to describe grinding systems for 20 to 30 years. However, Williams and Meloy (IMPC, pp. 73-79) pointed out some of the inherent problems with this modeling approach and that there is no unique solution for the unconstrained PBM for grinding. Many of the current constraints used to back-fit selection and breakage functions were also shown to have problems. The need for a more fundamental means of determining these parameters was indicated.

Jan 1, 1994