Search Documents

By T. Hollingsworth

The Boddington Gold Mine, located near Perth in Western Australia, has recently completed the construction of a new process plant. An overland conveyor system was installed to convey the ore from the primary crusher to the process plant. This paper will discuss the overland conveyor?s mechanical design including dynamic analysis and the selection of primary mechanical and electrical components.

Jan 1, 2010

By C. M. McCulloch

More and more mining underground is being conducted using the longwall method. Likewise, many new surface mines use area or mountaintop removal methods. These methods can have a significant impact on surface and groundwater resources. The overall study of the effects on surface and groundwater from mining is referred to as the probable hydrologic consequences (PHC) determination of mining and reclamation. Collection and interpretation of information concerning groundwater and surface water quality and quantity, as well as detailed geologic analysis, is required to adequately define the impacts of mining. This paper discusses the present day requirements and methodology of preparing a PHC for a large mining operation in the eastern coalfields.

Jan 1, 1995

By D. Kruse, M. Sanaei

"3D finite element models of the Segmentally Lined Shaft (SLS) structure are simulated as means of numerical analyses of the system’s structural behavior. Top-down constructed rings, comprised of precast concrete segments, create a large diameter, relatively shallow underground space that can be utilized for various applications. To further investigate the effects of soil conditions and different loadings on the shaft structure, the FE model was run under various boundary conditions. Simulations include a) effects of various soil layers on the SLS, including a circumferential boundary of modified ground, b) effects of various soil layers on the SLS without any ground modification, c) Seismic analysis of the SLS with ground modification and d) Seismic analysis of the SLS without any ground modification. Comparing the analyses outcomes emphasizes the significance of the inclusion of the ground modification boundary in the structural performance of the SLS. INTRODUCTION TO SLS Underground structures are classically built rectangular in shape, which normally requires a two-step construction process beginning with installation of temporary shoring to support earth loads during the excavation, followed by the construction of the permanent structure. Attractive and practical alternatives are circular shafts referred to as segmentally lined shafts (SLS). The structure consists of a stacked series of rings formed from an assemblage of precast concrete segments. Top-down constructed systems of large diameter, relatively shallow SLS structures provide both temporary earth support during excavation and permanent structural support for many civil and building applications. The circular shafts sustain the lateral earth pressure mainly through hoop-stress mechanism, resulting in improved stability and structural efficiency. Cylindrical shell structures with large diameter to wall thickness ratios are prone to buckling under external pressure. In typical designs of small diameter shafts and tunnel linings with small diameter to wall thickness ratios, nonlinear buckling analysis (i.e., nonlinear geometric analysis) is usually not considered, since the buckling capacities for those structures are much higher than typical pressures encountered at their design depths. With an economically viable wall thickness, buckling becomes a critical issue, which should be addressed, for circular shafts with very large diameters. In the design and construction of the SLS, the stability of the structure can be improved by modifying the soil surrounding the circumference of the shaft to a limited thickness and to about 10 ft below the finished shaft structure. This thick wall of soil mixed with cement creates a composite integrated structure while serving additional purposes such as ground control and ground water seepage cutoff."

Jan 1, 2016

By Valerio Violo, Antonio Raschillà, Livia Cicinelli

"The Cityringen project foresees the construction of a new circular metro line in and around the city center of Copenhagen. Both drives, the north and the south one, required the TBMs to be equipped in order to cope with contaminated water table and soil. The north drive mined in water contaminated with chlorinated compounds, including chloroform and vinyl chloride, while the south TBMs excavated in a highly benzene contaminated area, becoming the first TBMs to complete such a challenge. Despite the pollution and the stricter operative procedures, the production has been extremely successful with record up to 520 m in one month and 32 m in one day. 1 INTRODUCTION The Cityringen is an extension of the existing metro line. The 15 km long twin tunnels will form a new circular line with 21 new stations (17 + 4 crossovers). When finished it will interchange with the existing metro, rail and bus infrastructure at key locations around town, taking 90% of Copenhagen citizen at less the 600m from a metro station (Figure 1). The Contract has been awarded in April 2011 to the Copenhagen Metro Team (CMT), a joint venture between the Italian companies Salini Impregilo, Tecnimont and Seli SpA. Tunnels are being excavated with 4 Seli-Kawasaki EPB TBMs, two of which manufactured in Denmark by Seli Tunneling Denmark ApS, which is also operating them. At the moment this article is written 50% of the tunnels have been completed and over 40% handed over for the electromechanical works. Seli Tunnelling Denmark is a Danish company constituted in 2012 as a subsidiary of Seli SpA for this project and subsequently acquired by the Salini Impregilo Group in 2015."

Jan 1, 2016

By Jeramy B. Decker, Paul H. Madsen

"During the excavation of the north bound tunnel of the Devil’s Slide Tunnel project, deformation (convergence) was measured after passing through Fault Zone B. The tunnel convergence was not symmetrical, but was larger on the left side of the profile. It was determined that a shear zone nearly parallel with the tunnel drive was contributing to the uneven deformation. This paper will discuss how it was determined that the shear zone existed and how multi-point borehole Extensometers (MPBX) were used to verify that a significant amount of the deformation was occurring due to movement along the shear zone as the excavation was advanced. In addition, performance of the shotcrete liner in the area of the convergence will be examined. Finally, the paper will consider the means and methods that were utilized to ultimately control and stabilize the deformation. INTRODUCTION The Devil’s Slide Tunnel Project consisted of excavating two 1,250 meter tunnels each with a profile of 80 m2 utilizing the New Austrian Tunneling Method (NATM) or otherwise known as the Sequential Excavation Method (SEM). The tunnels are part of the California Coastal Highway south of Pacifica, CA, a suburb of San Francisco. The tunnels were opened to traffic in March of 2013. Geological Setting The tunnels run north-south through the San Pedro Mountain ridge, which is part of the Santa Cruz Mountains. The tunnel lies within the San Andreas Fault system and is 7.2 km west of the surface trace of the San Andreas Fault and 2.8 km east of the surface trace of the San Gregorio Fault. The 10 km strip between these two faults is referred to as the La Honda structural and terrain block (Decker et al. 2010; Amini et al. 2005; Earth Mechanics Inc. 2003). Locally, the tunnel passes through three blocks representing different geological conditions: South Block, Central Block, and North Block (Figure 1) (Decker et al. 2010; HNTB Corporation et al. 2005). The South Block consists of Mesozoic aged granodiorite and quartz diorite. The South Block also contains many local shear zones and a low angle thrust fault (Fault A). The South Block ends at Fault B, which is the southern border of the Central Block."

Jan 1, 2016

By Michael Schultz, Gregory Sanders

The City of New Haven is planning to construct the Downtown Storm Sewer Infrastructure Improvement project to mitigate on-going stormwater flooding in the Long Wharf District. The proposed project includes a 685 cubic feet per second (cfs) stormwater pump station and a 3,200 linear feet (975 meter) long tunnel segment with an internal diameter of 120-inches (3.05 meters). This paper presents the aspects of the final design and the use of the cloud-based data management software to make better data-informed decisions. The software was used to create a spatially aware database of the subsurface conditions, as well as improve visualization and analysis of the soil properties.

Dec 1, 2022

By T. Peter Philip, Erich U. Petersen, William J. Tafuri, Donald M. Hausen, Douglas N. Halbe

Scarcely a month goes by that I or someone else at Newmont Mining or Newmont Gold isn't asked to give a talk on the topic I was asked to discuss today. Investors, financial analysts, geologists, metallurgists, even our government--everybody wants to know what the future holds for gold mining. Well, you're not going to get exactly what you asked for. Today, I'm prepared to focus primarily not on what the future will bring to us, but rather on what the future will demand from us. More than that, I cannot undertake because it isn't within my scope to predict how wise and resourceful everyone in our industry will be in the future. What our future will hold, as I see it, will depend on our--and our colleagues'-- responses to these very real demands. Three critical issues stand out in my mind as to what the future will demand of us in the gold mining industry. And these demands will be for: 1. The very greatest of technical expertise and innovation. 2. The highest order of environmental sensitivity and timely accommodation. 3. Planning, planning and more planning. All of these flow inexorably today from the traditional objective of any mining company--or any company in any business, and that is, to make money. Nothing as I see it, should be undertaken by a geologist, metallurgist or even an environmental department, unless the exercises will enhance profits; and nothing may be ignored which can have consequent damage to the bottom line. Thus, the three issues I've listed for you subordinate themselves to the objective of making money, although at least in the environmental area, it might seem to some that we can only incur additional costs without even a dollar-for-dollar return. I hope to disabuse you today of any such out-of-date notion. Let's tackle the first issue-- Technical Expertise and Innovation. Newmont Gold Company this year is celebrating its 25th anniversary of successful and profitable operations on the Carlin Trend. Carlin in 1961, which is when exploration began on the "Trend" by Newmont, actually may share a lot of similarities with Carlin today. They didn't then know where the gold was and, if they found it, they had one hell of a challenge mining and processing ore at a profit because gold was selling at only $35 an ounce. Today, we know where the current reserves are. But we don't know where our future reserves lie. Furthermore, we don't know exactly how we're going to mine them, and, as everyone here knows too well, we don't know what the optimum metallurgical treatment is, even if we can find and mine them. And all that despite the abundant level of modern experience and skills within the current generation of mining companies, and the fact that, even taking inflation into account, gold sells at a higher price today than in 1965 when Carlin began operations. But, of course, I'm telling you what you already know.

Jan 1, 1990

By Francesco Chiappalone, Marco Invernizzi, Franco Gasperin, Fabrizio Fara

As part of the Ship Canal Water Quality Project, 2.7-mile Combined Sewer Overflow tunnel is excavated with a 21.5-foot diameter EPB Tunnel Boring Machine. Due to the difficult geological and hydrogeological conditions, the tunnel is excavated maintaining a ground support pressure between 1 and 3 bar imposing significant challenges to the projects. The first part of the paper describes the general characteristics of the project while the second part focuses on the challenges and technical details of the pressurized breakthrough that took place in a deep shaft excavated in urban environment as part of the project.

Jun 23, 2024

By Rohan Fernando, David P. Snyder, John F. Burr, Susan M. Moore

"The Mine Improvement and New Emergency Response Act of 2006 (MINER Act Public Law 109-236) was passed by Congress in response to three major underground coal mine accidents in the United States that claimed the lives of 19 miners. The Act resulted in substantial changes in the underground coal industry relative to the use of technology for mine escape, rescue, disaster response and other areas where the lack of these technologies contributed to the fatalities caused by these tragedies. This year marks the 10th anniversary of the MINER Act, which makes it an opportune time to reflect on the events that led to its passage, the changes that have been made since then, and the work that remains to be done.As discussed below, the last decade has demonstrated tremendous cooperative efforts among mining operators, technology innovators, labor, The National Institute for Occupational Safety and Health (NIOSH), the U.S. Mine Safety and Health Administration (MSHA) and state regulators, resulting in substantial improvement of the technologies used for escape and rescue and noteworthy progress toward meeting many of the goals of the MINER Act. While the MINER Act and this article pertain primarily to coal mining, many of the technologies are equally applicable to any underground mining and have already found some acceptance outside of coal.Technology gaps targeted by the MINER ActThe MINER Act addressed several technology challenges:• Problems with donning and switching between self-contained, self-rescuers (SCSRs).• Poor visibility in smoke.• No wayfinding assistance for escape from the mine.• Limited breathable air supply.• Inability to locate trapped miners.• Inability to communicate with trapped miners.• Failure of mine seals."

Dec 1, 2016

By T. A. Toney

With new lightweight designs, spirals have become standard equipment in coal preparation plants worldwide. To their credit, spirals typically show very low coal losses to the refuse stream under most operating conditions. However, spirals do tend to separate at cut points in excess of 1.80 S.G. Attempts to obtain lower cut points have typically resulted in coal losses to middlings. Middlings retreatment with secondary spirals is therefore becoming common place. Other forms of retreatment with water-only cyclones, hydrosizers, and recirculation have been attempted with some success. This paper reports on a novel (Patent Applied For) approach to retreating spiral middlings m a heavy-media-cyclone circuit.

Jan 1, 1998

By P. Grotjohann

In processing heavy mineral sands, the low feed concentration and respective high value of the desired minerals require high capacity production and sharp classification/separation techniques to reduce the specific production costs. The allflux® separator, a new process system introduced to the heavy mineral industry, meets these criteria in an economical way. Its two-stage process, a combination of rising current and fluidized bed technology, allows the treatment of extremely high massflows in a single unit. Using concepts that have proven successful in processing concrete sands for many years, testwork in coal, iron ore, and heavy minerals looks very promising.

Jan 1, 1998

By Z. Yu

The effect of particle size on coal dewatering has been well recognized However, there are no systematic studies on ultrafine coal dewatering. The results discussed last year revealed the effect of flocculant type and coal wettability on the filtration of ultrafine coal In this paper, the differences in dewatering between -25 µ m ultrafine and -500 µ m fine coal with addition of flocculants, surfactants and oil-emulsions in vacuum filtration are further investigated Significant differences were observed in the reduction of the cake moisture. The utilized emulsions were found to be very powerful and promising filtration aids for both ultrafine and fine fractions of hydrophobic and hydrophilic coal

Jan 1, 1995

By R. Patterson

Tracer gas sampling methods are useful for monitoring ventilation systems, especially in remote or inaccessible areas, and can be utilized for analysis of the ventilation system immediately following a mine emergency. However, the success of this technique is largely dependent on the accuracy of release and sampling methods. Analysis of sampling methods is crucial for rapid response and dependable results during emergencies. For the purpose of this study, four well-accepted sampling techniques currently used in the mining industry were compared using solid-phase microextraction (SPMe) fibers with sulfur hexafluoride (SF6), an industry standard, as the tracer gas. Current sample collection techniques include plastic syringes, glass syringes, Tedlar bags and vacutainers. SPMe fibers are used in a variety of industries, from forensics to environmental sampling, and are a solventless method of sampling analytes. To analyze these sampling methods, samples were taken from a 0.01 % standard mixture of SF6 and nitrogen and analyzed using electron capture gas chromatography. A relative standard error of less than 10% validated results to compare the accuracy of various methods. The technical and practical issues surrounding each sampling method were also observed and discussed.

Jan 1, 2011

By S. Hodgson

The Red Dog zinc/lead deposit in northwest Alaska is the second largest zinc deposit ever discovered. Being developed by Cominco Alaska with startup scheduled for early 1990, it will ultimately be the largest zinc mine in the Western World. Table 1 illustrates the reserves of the deposit.

Jan 1, 1988

By B. J. Scheiner

A ferrous chloride-oxygen leaching system was investigated by the Federal Bureau of Mines as a means of re-covering copper and silver from a sulfide concentrate that had been pretreated to remove a majority of the antimony. The pretreated concentrate contained Cu, Ag, Pb, Zn, Sb, and As. Parameters affecting metal extraction, such as temperature, pressure, amount of ferrous chloride, and initial hydrogen ion concentration, were studied. Copper extraction of 98 pct was achieved by leaching 4 hours at 40 pounds per?square inch gage (psig) and 1000 ?C. Copper was recovered from leach solutions by cementation with iron, and the resulting ferrous chloride was recycled. Leaching the residue with cyanide followed by electrowinning recovered 99.7 pct of the silver. Iron, Sb, As, Pb, and S reported to the tails.

Jan 1, 1978

By Ravi Shah, Augusto Lucarelli, Daniele Peila

"In mechanized tunneling the annular gap between the segmental lining and the surrounding soil caused by tunnel driving, must be backfilled almost instantaneously with an adequate grouting mortar. The objective of this research is to perform a fully three dimensional modeled parametric study using FLAC 3D and evaluate the effects of backfill grouting on the tunneling performance. The research focuses on comparisons between different injection materials and state-of-the-art Bi-Component grout and their effects on the settlements on the surface. The research consists of testing a regular situation of tunnel excavation using a shielded machine with face under pressure. The tunnel dimensions and the soil properties are selected as close as possible to the reality and based on Turin Metro case. 1 INTRODUCTION Excavation of tunnels in urban areas can induce ground movements, which have negative effects on existing structures. In such scenarios, shield tunneling has become a well-accepted construction method in various ground conditions. It is characterized by relatively complex interactions between the soil, the tunnel boring machine (TBM) itself, the tunnel lining and the tail void grout. The problem to control the settlement depends on the face pressure, ground properties and back filling procedure and material of the tail void. The face pressure acts against the front to guarantee the face stability. In case of EPB TBMs the stability of the tunnel face is ensured through the excavated soil itself, which is conditioned and is maintained in compressed state within the excavation chamber. When excavating with TBMs a tail void is created between ground and the lining (Fig.1) after the TBM excavation and ring assembly that must be backfilled instantaneously by injecting the backfill material through the TBM’s tail shield. The process is of primary importance as it reduces the surface settlements and creates an immediate link between the ground and lining, sealing against ground water and leakage, reducing the differential movements between segments and providing long-term stability. The most used backfilling materials are: Inert mixtures that do not contain cement instead sometimes they are replaced by fly ash or other substitutes. A typical design of an inert mortar consists of sand, fly ash, bentonite and water. Pea gravel, which is constituted of granular materials with grain size ranging from 8 to 12 mm. This mixture is highly recommended for tunnels being constructed in rock mass with little deformation rates.Cement mortar is composed of cement, water, aggregates and sometimes bentonite. Cement controls the principle mechanical property of the mix, which can reach high values of 15-20 MPa in 28 days. The aggregates contribute towards the shear strength and reduce the pumpablity of the mix (Thewes and Budach, 2009). The reduced active systems have a cement content of 50-100 kg/m3, whereas the active system the binder component derives full hydration with cement content of over 200 kg/m3 ."

Jan 1, 2016

By Denys B. Smith

Electric logs and cuttings records from Zechstein 3 and 4 strata in boreholes in the British Sector of have been interpreted in the light of numerous cored boreholes through this sequence in north-east England. This interpretation shows that potash salts in the two cycles are thickest and most consistent in a belt 20 to 40 km wide parallel with and a few kilometres from the present basin margin, and are here generally similar in grade to those known onshore. The potash ores in both cycles are mainly of sylvinite in onshore areas, the layered Upper the Southern North Sea Potash of the fourth cycle being rather less variable but generally of appreciably lower average grade than the Boulby Potash of the third cycle. Potash salts in both cycles are highly variable in thickness and grade in basin centre areas where they have been grossly affected by diapirism of the thick second cycle salts.

Jan 1, 1978

By Thomas Fiest, Helmut Wannenmacher, Wulf Schubert, Manuel Entfellner

Mining and tunneling in so-called “squeezing ground conditions” at high in-situ stress can result in substantial and enduring ground deformations. The magnitude of deformations is closely tied to the applied excavation- and support concept, though typically, they can reach tens of centimeters. The yielding principle is based on the idea, that the need for support capacity decreases as deformation increases. To enable controlled ground deformation and safe working conditions, yielding elements as a part of the shotcrete lining are implemented. These types of elements avoid an overstressing of the shotcrete lining. During the deformation process, the support pressure of the yielding elements and lining increases, thus stabilizing the ground. Furthermore, long-term creep deformations of the rock mass can be absorbed with such a system. This economic support technique represents the state-of-the-art infrastructure tunneling practice in squeezing ground condition. A novel yielding element of High-Strength Expanded Polystyrene (HS-EPS) was invented, which overcomes existing systems’ drawbacks. This innovative system is lightweight and allows for safe and rapid installation. Furthermore, the modular setup of the element enables an easy on-site adaption to react to in-situ deformation patterns and changing ground conditions. Recent experiences from applications in Alpine base tunnels in squeezing ground are presented.

Jun 25, 2024

By K. J. Stanaway

Concentrations of minerals between 3.5 and 5 specific gravity such as ilmenite, rutile and zircon in large accumulations of sand constitute "heavy mineral" placers. Two fundamentally different modes of formation characterize "trap" and "bed" placer variants. Smaller and generally higher grade trap placers form during sediment erosion or reworking. Because of their smaller size, they rarely yield economic heavy mineral deposits. They become economic, either if they contain more valuable "heavies" such as gold, or, if they occur within or near much larger but lower grade bed placers. Bed placers form during sediment accumulation episodes in any environment and lithofacies where mineral supply and fluid dynamics are favorable. Three heavy mineral deposits are discussed to illustrate bed placer geology and how trap placers occur with and relate to them.

Jan 1, 1991

By Byron R. Berger

Epithermal Ag-Au deposits form at low to moderate temperatures in near-surface environments. Historically, these deposits have been the source of high-grade ores. Increases in the market prices for gold and silver make lower-grade ores economically viable when available in large tonnages. Both the high-grade and bulk-tonnage ores are a consequence of the same processes, and general models of epithermal systems can be useful in the search for new precious-metal resources. A detailed study of deposits at Round Mountain, Nevada; Balei, Russia; Creede, Colorado; Guanajuato, Mexico; and Chanarcillo, Chile, indicates that the hydrodynamics of the fluid systems as determined by fracture geometries, the permeability, and composition of the host rocks are the key factors in the creation of both high-grade and bulk-tonnage epithermal deposits. End-member models that explain the range of observed deposit characteristics are: (1) the hot-springs deposition model; (2) the stacked-cell convection model (where mineral deposition occurs laterally along the interface of two partially separated fluid reservoirs); and, (3) the closed-cell convection model (where deposition occurs in vertical zones due to the relatively unimpeded vertical flow of hydrothermal fluids). Boiling and fluid mixing appear to be agents of precious-metal deposition with the self-sealing of the hydrothermal system being an important adjunct to boiling. Imaginative application of model concepts in exploration has led and can lead to the discovery of new high-grade and/or bulk-tonnage precious-metal deposits.

Jan 1, 1982