Search Documents

By K. N. Han, P. B. Queneau, A. Stojsic, M. J. Collins, V. J. Ketcham, R. M. G. S. Berezowsky, W. D. Vardill

The bulk of the ore found in the Lihir Island deposit is refractory in nature, with the gold contained in auriferous pyrite. In support of an evaluation of the development of this deposit by Kennecott (a wholly owned subsidiary of RTZ) and Niugini Mining Ltd., testwork has been carried out at the Sherritt Research Centre to demonstrate the amenability of the Lihir ore to pressure oxidation pretreatment to liberate the refractory gold. The results of pilot plant treatment of the Lihir ore in a continuous circuit with a feed rate of between 10 and 30 kg/h ore are described. The integrated circuit comprised pressure oxidation, residue washing, and gold recovery from the washed residue by carbon in leach or carbon in pulp cyanide leaching. Significant factors affecting gold recovery included temperature and retention time in the pressure oxidation step, and the concentration of soluble chloride in the feed. Gold extraction from well washed ore, after oxidation at 210°C for 66 minutes in the autoclave, was typically between 94 and 96%, compared with less than 30% by direct cyanidation.

Jan 1, 1993

By Thomas E. Bruner

Today many small diameter tunnels are being constructed in Metropolitan areas and towns as transmission holes for utilities such as water, electricity, natural gas and sewage, to name a few. These tunnels function as utilities beneath the streets, highways, railways, and other structures where open-cut techniques are impractical for any one of a number of reasons. Many such bores range in diameter from 15 to 72 inches and in lengths from 100 to 500 feet. Auger drills with auger type heads have long been used to bore these "road crossings" as they are usually termed; however, many such crossings must be bored in rock with rock-boring heads. Rock with a compressive strength of 15,000 p.s.i. and higher seems to present the greatest challenge for the contractor. These rocks include most igneous and metamorphic rocks and some sedimentary rocks. In general, this grasps most granites, basalts, gneisses, slates, schists, quartzites, limestones, and cherts. In the past ten years boring machines have been developed and used to excavate road crossings through hard rock. Many crossings have been successfully excavated using these machines, and the degree of success has increased substantially in the last few years. A variety of machines have been built and manufactured to bore most rock in a range of diameters up to 72 inches. The machines vary in capabilities, size ranges, and designs but all perform the same basic task and function of boring horizontally. Incidently, here the term horizontal implies horizontal or within five degrees of horizontal. In addition, there is a wide variety of designs, sizes, and types of drill stems, joints, and pipe to meet the various conditions and

Jan 1, 1974

By R. S. Ondrey, R. A. Haney, T Tomb, R. T. Stoltz, Novakowski D. L. Chiz, E. J. Gerbec, D. J. Atchinson

Although the number of operating longwalls in the United States (approximately 100) has remained relatively constant over the last five years, longwall production levels have significantly increased and in some cases more than doubled. As a result of this production increase, control of respirable dust continues to be a problem. Therefore, the Mine Safety and Health Administration (MSHA), Pittsburgh Health Technology Center, Dust Division, initiated a study to investigate the availability and adequacy of technology for controlling dust on longwall mining operations. The study involved 23 longwall mining operations in three different Coal Mine Safety and Health Districts. Each operation was visited for a full shift. Respirable dust samples were collected on face personnel and at fixed locations along the face. Methods being used to control dust were noted, with special emphasis placed on obtaining quantitative data relative to ventilation, headgate dust controls, cutting drum sprays, external machine sprays and cutting sequence. Attempts were made to correlate dust control practices in place at the time of the visit to dust concentrations measured at the tail and on the tail shearer operator and to the average of all the dust concentration measurements from the occupations sampled. The methods used to control dust were also compared to the gamut of methods known to be available. This paper presents a discussion on the effectiveness of the methods being used to control dust and on the availability of technology for the control of dust on longwall mining operations.

Jan 1, 1991

By Betty L. Gibbs

What does the information age mean to mining companies? The perception of greatly increased access to information is based on modern communications through ‘smart’ fax machines and computer networks. Computer media allow us to `talk' to the President or to a sister in Australia. If we need data to help put together a mining permit, we can find that data somewhere on computer media. The vast amount of easily accessible information quickly overwhelms us. To avoid `information burnout,' we must learn to target searches and be able to discriminate between dross and information that is useful to our goals. If you watch commercial TV, you have learned to screen out most product commercials. A similar screening process must be applied to computerized information sources. You may need to sort through a lot of irrelevant information before finding the pearls you are looking for. ‘Smart’ fax machines can send information with no direct human intervention. MINES FaxBac, for example, from the US Bureau of Mines instructs you to enter four-digit numbers to have particular reports sent directly to your fax machine. Software vendors use a similar system to supply information about their products. You select an item by number, and the related brochure is faxed to your machine. To compete, the industry must maintain access to as many information sources as possible. The availability of computers and software for almost every conceivable application allows us to accomplish work faster than we ever thought possible, even as recently as 10 years ago. Most mining companies have become aware that doing geology, reserves, mine planning and other technical tasks completely by hand is much too slow. The world moves faster, drilling happens faster, mining happens faster, all related activities happen faster. We no longer have the manpower or time to keep all maps. calculations and records up to date.

Jan 1, 1994

By John K. Adams

Phosphorus may be incorporated into sedimentary rocks in at least four different ways: (1) by the accumulation of detrital mineral fragments, (2) by the accumulation of phosphatic organic debris, (3) by diagenesis and (4) perhaps by the primary precipitation of calcium phosphate. Based-on the petrographic examination of Cretaceous and Tertiary sediments from the northern and central parts of the Atlantic Coastal Plain, Diagenesis is the most important of these mechanisms. Both syndiagenesis and epidiagenesis are required to explain the origin of all the diagenetic phosphate mineral species which occur in the northern and central parts of the coastal plain. Syndiagenesis produced much of the coastal plain's apatite. It was operative below the sediment-water interface while the substrate was being compacted. Compaction forced pore waters, which were enriched in phosphate by the decomposition of organic matter, upward through calcareous sediments. The PO43- radicle replaced the CO23- and calcareous nodules, pellets and shell fragments were converted to apatite. Epidiagenetic reactions occurred in the subaerial environment where downward percolating meteoric waters carried phosphate in solution to cites where cation activity was sufficiently high to form new minerals. Vivianite may form where ferrous iron is available and wavellite and variscite may form in the presence of aluminum rich minerals. Textural evidence suggests that many of the reactions were repeated. The present day appearance of apatite, vivianite, wavellite and variscite in the coastal plain may represent several generations of diagenesis.

Jan 1, 1972

By Carl G. Bock

INTRODUCTION Rapid transit systems involving near surface tunneling in hard rock are becoming more numerous, especially along the northeast corridor of the East Coast. Tunneled systems are under construction in Washington, D.C. and are being planned for Atlanta, Buffalo and Baltimore. Near surface tunneling is defined for this paper as being that in which the crown is 100 feet or less below ground surface. For Rosslyn Station, the total cover ranged from 52 to 70 feet. The rock cover, however, ranged from 40 to 50 feet which is slightly less than the station height and about two-thirds of its width. Rosslyn Station (Fig. 1) is the only station excavated completely in hard rock in the Virginia portion of the 98.5 mile Washington Metropolitan Area Transit Authority's (WMATA) rapid transit system. The station site, oriented in a north-south direction beneath a main thoroughfare and flanked by multistory office buildings, was fixed by the need to serve a dense population center at a specific location and geologic conditions were a secondary consideration in siting. There was no previous underground rock excavation in the Washington Metropolitan Area of the size and scope of Rosslyn Station that offered a practical case history guide to the geologic conditions and excavation problems to be encountered. GEOLOGY The regional geology of the Washington Metropolitan Area is divided into two physiographic provinces by the northeast trending Fall Line (Fig. 2). Northwest of this boundary is the Piedmont Province

Jan 1, 1974

By P. Hambach

Murer Company, Andermatt, Switzerland, can claim to have done pioneer work in the construction of inclined shafts. This happened in 1968/69, when we decided to bore with a Wirth tunnel borer an inclined shaft, 1100 m in length, 3.0 m in diameter, and with a grade of 65%, in the 2400 kilo pascall per sq. cm granite of the Montblanc Massive. The whole excavation was accomplished in ten months which, at least for European conditions, can be claimed as a record. It was, at least to our knowledge, the first inclined shaft to be bored full-face (Fig. 1). Encouraged by the experiences and performances attained at Châtelard, we approached other projects of the same kind. We were awarded, together with Hochtief Ltd., Essen, a contract from Schluchseewerke, Freiburg, Germany, in December 1969, for the construction of a penstock for the Hornbergstufe at Wehr, Germany, with a diameter of 6.3 m. This inclined shaft with a grade of 55% is located in Schwarzwalder granite with a compressive strength of up to 2000 kilo pascall per sq. cm, about 31,000 psi. As no exact geological data were available about the rock to be worked, and a fault zone from 80 to 150 m long had to be faced, as well as a few individual fissures of varying thickness, it was decided to use the multi-stage method. The 3-m diam tunnelling machine which had driven the oblique shaft at Châtelard had now finished work, and an immediate beginning was made with driving the pilot staft. This was very welcome to the contractor, since exact information about the type of rock present and the inflows of water was required immediately and before the final borehole diameter was fixed, for the purpose of dimensioning the supports to be subsequently installed.

Jan 1, 1974

By Robert L. Akright

The Sumich (Victorine) gold mine is located in the Toiyabe Mountain Range on the east side of Victorine Canyon, a north-trending branch off Kingston Canyon in the northwest quarter of Section 27 and southwest quarter of Section 22, T16N, R43E, in the southern end of Lander County, Nevada (Fig. 1). HISTORY Discovered in 1862, the Victorine reached a peak of development between 1872 and 1887. The "Victorine" and "Morning Star" lode mining claims, located on the outcrop of a prominent auriferous quartz vein, were patented in 1869 and 1891, respectively. 1, respectively. Gold ore was mined underground in adits driven, on the level, directly into the side of the mountain. Ore brought to the surface was trammed about 457 m (1500 ft) south on a track constructed along the contour to ore bins. From this transfer point, the ore was moved by aerial tram to the bottom of the canyon then hauled by horse-drawn wagon to the mill located about 3.2 km (2 miles) east down Kingston Canyon. Exact details of the milling process used on the Victorine are lacking, but old reports mention water-driven stamp mills, amalgamation, chlorination, and cyanidation. Gold and silver mill products are reported to have been sent to England for final refining. High-grade gold values of 103 g/t (3 oz per ton) remaining in mine walls and on outcrops, attest to the lack of success in treating the Victorine ore in the early mills. The Victorine mine may have been worked sporadically after 1887 with little success. In 1934, control of the property was acquired by William P. Moloney, an attorney from Marion, OH, who also control- 1 led an interest in the successful Goldacres mine in Lander County, NV. This property was studied, sampled, and metallurgical tests were done in 1934, but no development resulted from this work.

Jan 1, 1990

By Eric Forssberg, Mats Hallin

INTRODUCTION Evaluation and optimization of mineral processes has been going on since the the first plant started hundreds of years ago. A huge mass of knowledge has been collected since then. The main problem with this type of empirical knowledge of complex processes is that it is very difficult to formulate and document. The methods used for collecting the knowledge is not consistent but-varies with "he person" that does it. In the late 60's and early 70's efforts were made to use computer based techniques to evaluate process performance and to formulate process models for mineral processes. Models were developed, such as the flotation model by R. P. King (1973) which is still used to simulate flotation circuit behaviour. During the 70's. a number of mass balancing packages were developed together with process simulation packages. The industrial sector also made great efforts to develop and utilize computer based systems for process control and evaluation. The expert system that BOLIDEN created in 1974 at the Kristineberg plant was a remarkable achievement considering the hardware (CDC 3600) and the software tools (FORTRAN) available at that time. The main obstacle to successfully implement optimizing computer control of mineral processes was and still is the limited knowledge about the dynamics of complex processes. There are, however. many activities going on in this area today and it seems that the technology is very near a break through. Process evaluation is the most important tool to improve and maintain the optimal performance of a process. Today dedicated computer based techniques are used for fast and reliable screening of the processes. The stages in process evaluation consist of three basic steps: - Data acquisition, manually or by data logging. - Data refining, mass balancing and parameter calculation. - Data evaluation. The refined data can then be used for model construction/calibration and subsequently for process simulation. This paper describes two studies where the techniques mentioned above are used to evaluate and simulate

Jan 1, 1991

By A. W. Khair, S. S. Peng

Discussion by J. Parker Gentlemen; Rainy day in Upper Michigan, a good time to catch up on reading. Am doing that, and have a couple of questions concerning the K and P paper on roof problems and supports. I wonder if the authors can enlighten me. The compressive strength of the coal was reported as 4.4 MPa (633 psi) and compressive stresses measured in the coal seam were reported at around 27.6 and 48.2 MPa(4000 and 7000psi ). Can such a soft coal actually contain such a high level of stress? Can it be measured as if the material were elastic, or does the coal behave plastically? Can that stress level be confirmed with hydraulic load cells? And if the coal is so soft, and if it is plastic, why is the stress field not hydrostatic'? The intact roofrock appears to be unusually strong, with compressive strength reported at around 145 MPa (21,000 psi), and some failures were noted as soon as the rock was exposed. Were tests run to find out how that rock responded to the addition of moisture, from sprays or from humid air? Did moisture weaken the rock? Did it cause the rock to expand quickly, thus to induce internal compressive stress? How can the near-vertical cutters, as shown in the photographs, be attributed to primarily horizontal stresses? Did the cutters follow any particular pattern in the development panels, which might be related to a particular stress pattern? For example, did they always appear alongside the stiffest pillar? Or always along the northwest rib? Was there any evidence of the pillars and entries "rotating" under the influence of differential horizontal stresses? How much did the entries and pillars rotate as the longwall face approached and passed? After rooffalls, did the openings assume shapes which would indicate a preferred shape in that stressfield and geology? Did crosscuts always survive without damage, as shown in the sketch?

Jan 1, 1992

By Arthur G. Strassburger

INTRODUCTION High in the Sierra Nevada Mountains of California, some 50 airline miles (80 km) northeast of Fresno, and near the John Muir Wilderness and Kings Canyon National Park, a large underground hydroelectric project is under construction. Pacific Gas & Electric (PG&E) Company's 1,125 MW Helms Pumped Storage Project exhibits a number of impressive statistics, unusual features, and other characteristics of interest to the tunneling or power plant designer and construction contractor. The most significant underground facilities include almost 20,000 ft (6,096 m) of 27-ft (8.2 m) diam concrete-lined pressure tunnel; 3,700 ft (1,128 m) of access tunnel; 1,600 ft (488 m) of steel-lined high-pressure conduit, 2 major underground chambers more than 1,000 ft (305 m) below ground; 3 deep vertical shafts, and one steep inclined shaft. Maximum static pressures within the conduits range from 200 ft (61 m) to 1,744 ft (532 m), with hydraulic transients that increase pressure to 2,500 ft (762 m). The purpose of these underground works is to provide 475,000 hp (354,350 KW) of water power to each of the 3 reversible pump-turbines, each connected to a 375 MW generator motor. The units, rated at 1,744 ft (532 m) maximum static head, are among the world's front-runners, considering the size-head combination. The Helms Project develops the existing power drop between two of PG&E's reservoirs, Courtright Lake and Lake Wishon. These reservoirs are retained by two concrete-faced rockfill dams completed in 1958, each storing approximately 125,000 acre ft (154 x 106 m3) of water. Although the project is intended to operate on a typical

Jan 1, 1981

By R. S. Shoemaker

It is said that there is nothing new under the sun and this is certainly true about refractory gold Ores. Ores which have been refractory to treatment have been the bane of the Metallurgist's life ever since gold has been recognized as a metal valued for its indestructability, malleability and beauty. Webster's Dictionary defines "Refractory" as; "Resisting control or authority, stubborn, resistant to treatment or cure, unresponsive to stimuli, difficult to corrode or draw out," And gives as a synonym the word "unruly." I don't think any metallurgist would disagree with these definitions as they quite accurately describe refractory gold ores as we know them and I wouldn't be a bit surprised if many of you in this room today had applied far stonger language to your own refractory ores in the course of your metallurgical test programs. Pliny the elder put it very well when he wrote in 79 A.D., Gold is the first of man's follies, Silver the second." Perhaps Pliny was speaking of "unassayable gold" or "incipient gold." These are truly refrac tory ores which probably existed before Pliny's time and although many people have claimed to have solved their metallurgy the untold wealth that lies within them has never been bankable. On the other hand, Virgil is his Aenead, could very well have been speaking of refractory ores when he wrote; "Quid non mortalia pectora cogis, auri sacra fames!" which translates as, Accursed thirst for gold! What doest thou not compel mortals to do. Certainly, gold was extremely rare at that time because it had to be recovered by much labor from the then refractory ores and their refractoriness caused the early metallurgists (or alchemists if you will) to seek an easier way to produce it; thus the long and fruitless search for the "philosopher 's stone" which would aid in turn-

Jan 1, 1990

By E. Turner

This is the 3rd Paper in a series by this author, the first two being published at the two previous International Conferences. Since the Aachen Conference, Rio Tinto has carried out an extensive benchmarking exercise to see how we are positioned with respect to other leading companies (in our sector and other sectors of major economic importance). We need to be sure that Rio Tinto is at the forefront of best practises in Sustainable Development (SD) and is using the most effective tools and methods. This paper will present key findings from this work. Rio Tinto Minerals, working as representatives of IMA-Europe was a leading contributor to the European Commission DG Enterprise Voluntary Reporting Scheme for SD Indicators in the Non-Energy Extractive Industry. In Rio Tinto Minerals we have been using these SDIs in the management of our business and the paper will report on how they contribute to the management of our business and the paper will report on how they contribute to business value in: deepening customer relationships, eco-efficiency of operations, land use planning and permitting for new and expanding facilities, community relations, policy engagement with government authorities and strengthening the bond between the company and employees. We continue to support the Voluntary SDI Reporting Scheme, considering it to be important in the expanding EU and as a model for other regions globally. For example we have ore suppliers in developing countries and we use these SDIs in assisting them to better their performance, for we have an obligation to use our influence for continuous improvement. The paper will describe this work. Over the last 12 months our company has created a new Industrial Minerals unit called Rio Tinto Minerals which brings together all the borates, talc and salt operations, R&D, marketing, sales and customer care worldwide. The paper will present also the new Sustainability Policy of Rio Tinto Minerals.

Jan 1, 2007

Throughout the 1970s, the US Bureau of Mines rode an ebb tide in Washington political circles. In rapid fire succession, the agency lost its mine health and safety enforcement responsibility (1973), a large portion of its energy research responsibility (1975), and then its fuel statistics functions plus a sizable portion of its coal R&D (1977). By 1978, johnny-come-latelies in the Energy, Labor, and Interior Departments had siphoned away from the Bureau some $125 million in program responsibilities as well as 900 of its employees. The bruising decade came to a close with a Department of Natural Resources proposal that, in its original form, would have scattered the Bureau’s responsibilities to the winds. There is no doubt in my wind,” said Lindsay Norman, acting director of the Bureau of Mines (see box), “that were the Bureau to continue down the path it was on, the next step was closing the doors and going out of business.” The doors are still open, but erosion of responsibilities had a devastating effect on the resources available to fulfill the Bureau’s mission. Devastating,too, in terms of internal morale, considering the Bureau had six directors in a 10-year span. “When the troops are in the trenches and are being shot at,” Norman said, “they need a leader—hopefully, a permanent one— that can get them advancing. This is something the Bureau did not consistently have in the 1970s.” In September 1978, Roger Markle climbed aboard as director of the Bureau to rejuvenate the 70-year-old agency. He resigned only six months later* but the program Markle set in motion is being carried through by Lindsay Norman. Since Norman’s appointment as acting director, he has spent considerable time on the road explaining his agency’s redefined goals. At one such stop in Duluth, Norman and his two deputy directors, Charles Kenahan and Mike Kaas, answered the following questions.

Jan 6, 1980

By S. R. Brown

A number of relatively recent factors associated with the design of new metallurgical processing plants have made the effective training of operators a requirement for a successful start-up. Some of these factors include large capital investment in a minimum of processing lines, highly complex process control systems, and stringent regulations on plant effluent, to name a few. More than ever, operating mistakes during the start-up phase can lead to substantial delays in achieving design production, as well as problems with government authorities if permit limits are exceeded. The only way to assure your return on plant investment is to ensure new plant operators have the knowledge to properly run the plant from the outset. A comprehensive set of operating manuals specifically targeted for plant operators and foreman, written by experienced operating personnel, is the only effective way to provide the necessary information for start-up-related training.

Jan 1, 1995

By V. P. Petrov

There is a great number of asbestos deposits in the USSR. Some of them are quite large ones. The main deposits of chrysotile asbestos can be seen in the sketch map (fig. 1). Bazhenovo deposit situated in Sverdlovsk region is the largest of them. It is on mining operations since year 1889. Systematical studies of asbestos deposits were begun from the first years of Soviet Government and connected with the names of K.E. Tarasov, P. M. Tatarinov, B. J. Merenkov, N.D. Sobolev, F. V. Syromjatnikov, V. N. Lodochnikov, V.P. Petrov, V.P. Eremeev, L.A. Sokolova, V. R. Artemov, V.F. Dybkov and many others. This investigations served the USSR to be one of the most important producers of asbestos in the world. In the limits of the report a characteristic of the main asbestos deposits of the USSR may be done in general outline, from the point of view of their genesis, and in order to show their common features and differences that must be taken into account for forecasting, exploration, and mining of asbestos. All chrysotile asbestos deposits of the USSR were formed of magnesium rock as a result of comparatively lower-grade temperature hydrothermal alteration and free crystallization of fibrous chrysotile in open cavities that served as catalyst As a matter of fact an important mineral for industry is not chrysotile in general, a widely distributed rock-forming mineral, but a long fibrous and mainly vein variety of chrysotile. It must serve for geologists as an important prospecting criteria. A geologist should search for the mineral not only places of possible chrysotile generations, but places where asbestos may be crystallized in its long fibers that could be fiberized well. The Soviet geologists distinguish two groups of chrysotile-asbestos deposits: (1) related to ultrabasic rocks and (2) related to sedimentary dolomite terranes, taking into account what the maternal rock was affected by hydrothermal solutions. The largest deposits related to ultrabasite. The largest deposits in dolomite are small ones but their asbestos contains almost no iron. So much asbestos is a better filler into insulating plastics. There is a few types of asbestos deposits in the limits of the ultrabasic group. The largest of them is a Bazhenovo type which the deposits of Urals are attributed, and Bazhenovo deposits is the first instance. The Bazhenovo type is characterized by the most complete zonality in disposition of various kinds of asbestization. This type of deposits is practically the only one to be in working now in the USSR.

Jan 1, 1978

By Gunnar Nord, Per-Anders Persson, Duri Prader

The paper gives a short resumé of the findings of the joint US - Swedish "Mechanical Boring (MB) or Drill and Blast Tunneling (DB) ? Workshop" in Stockholm December 1976. New developments and trends in both MB and DB techniques in Europe since 1976 are described, and information is given on some interesting new projects. Differences in contracting principles between the US and Europe lead to different practices for preinvestigations, design, excavation and arbitration and legal affairs. It is shown that this often leads to a higher cost in the US than in Europe for similar excavation jobs. A typical US tunnel job also has more men on the site than a similar job in Europe. This adds to the cost difference and is only partly balanced by a slightly higher rate of excavation in the US. A comparison is made between two quantitative methods of predicting MB penetration rates. These are in reasonable agreement. A probable future development in machine design is an increase in cutter load towards perhaps 25 tons per disc where the tunnel diameter is large enough to house the machine size dictated by the size of the very large electric motors required. Recent European developments in drill and blast technique include improved methods for cautious blasting, precision hydraulic drilling of small diameter holes, and non-electric interval blasting techniques. These developments still keep the drill and blast method ahead of mechanical boring costwise for tunnels in igneous rock whereas for most sedimentary materials mechanical boring has a lead, particularly for long tunnels.

Jan 1, 1979

By Qiong Wu, Qinghua Gu, Yichuan Lv, Jin Yuan, Caiwu Lu

"The cut-off grade is one of the important parameters of mining production. Different material cut-off grade is directed to different destinations. Based on reasonable and optimal cut-off grade, long term mining plan and investment decision analysis can be made for mining managers. In view of multiple-metals open-pit, the paper has proposed that multiple-metals cut-off grade optimization model is set using the objective function to maximize net present value (NPV). The method of equivalent coefficient calculation is proposed to convert multi-metals cut-off grade optimization to a single metal cut-off grade optimization. Then the optimization model is applied in a molybdenum and tungsten large open-pit mine in china. The parameters of concentrate price are calculated by PRT in the model and the curve of grade-recovery rate is analyzed and studied according to actual production data. Based on 3D metal deposit model, the distribution of grade-tonnage is analyzed. At final step, an optimal cut-off grade is proposed to guarantee to maximize NPV. The example shows that the model of multiple-metals cut-off grade optimization can provide reasonable analysis for optimal multi-metals cut-off grade and develop optimal production strategies. Introduction Cut-off grade is one of the most important parameters in metal ore mining because of its influence on the overall economic profit of mining production. Along with the development of the mining production, dynamic optimization of cut-off grade is necessary through the analysis of technical economy. It is better to manage the mining production according to the variation of market. The cut-off grade plays an important role in mining production."

Jan 1, 2017

By Stephen G. Tough, Ted M. Noskiewicz

INTRODUCTION For many years, in Europe and in North America, pre-formed metallic and concrete segmental linings in tunnels have been used extensively as temporary and permanent ground support systems. In the United Kingdom the use of cast iron as a means of ground support in mining shafts dates from the first decade of the 19th century. Although at that time wood tubbing was extensively employed, cast iron was used in shafts at Wallsend and Percy Main collieries in the North East of England. The original form of cast iron tubbing consisted of cylinders which were lowered bodily into the pit and were built from the bottom up, but subsequently they were subdivided into segments which involved the making of vertical as well as horizontal joints. Principally, the practice of providing immediate pre-formed support developed because of the incompetent state of the surrounding ground and, although this still remains the over-riding consideration nowadays, several other factors are examined before finally deciding what type of lining to use. Other branches of sub-terranean technology such as tunnel thrusting or immersed tubes (both of which involve pre-formed linings) can provide alternative solutions to problems hitherto thought better solved by bored tunnelling methods. However, this paper will confine itself to those linings developed for the more traditional tunnelling methods. Usually the shape of segmentally lined tunnels is circular because this profile is the most suitable for bad ground and many tunnelling machines. This does not always lead to the most economic use of space within the tunnel and horseshoe or elliptical linings are sometimes used in suitable ground. The number of segments

Jan 1, 1974

By Bruce K. Cantrell, Stephen W. Stein, Kenneth L. Williams, David Hassel, Harvey Patashnick

In June 1992, the Mine Safety and Health Administration (MSHA) published the 'Report of the Coal Mine Respirable Dust Task Group; Review of the Program to Control Respirable Coal Mine Dust in the United States." As one of its recommendations, the report called for the accelerated development of two mine dust monitors: (1) a fixed-site monitor capable of providing continuous information on dust levels to the miner, mine operator, and to MSHA, if necessary, and (2) a personal sampling device capable of providing both a short-term personal exposure measurement as well as a full-shift measurement. In response to this recommendation, the National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Center, initiated the development of a fixed-site machine-mounted continuous respirable dust monitor. The technology chosen for monitor development is the Rupprecht and Patashnick Co., Inc. tapered element oscillating microbalance. Laboratory and in- mine tests have indicated that, with modification, this sensor can meet the humidity and vibration requirements for underground coal mine use. NIOSH is continuing that effort by developing prototypes of a continuous dust monitor based on this technology. These prototypes are being evaluated in underground coal mines as they become available. This effort, conducted as a joint venture with MSHA, is nearing completion with every promise of success. The immediate benefit of this effort will be to researchers, regulatory personnel, and mine personnel, by permitting evaluation of specific mining practices to see which expose mine workers to excessive dust levels. Using this information, mine personnel can optimize mining procedures to reduce dust exposure. MSHA and the operators will also be able to use the dust concentration data to judge whether dust plan parameters are adequate to continuously maintaining environmental dust levels below the applicable standard. The second development recommended by the Dust Task Group was a person-wearable version of the continuous dust monitor. It will be a monitoring system designed to provide a measurement of worker exposure to respirable dust, both during and at the end of the shift.

Jan 1, 1997