Search Documents

By W. C. Yates

Lack of visibility from cabs of the large haulage trucks used in open-pit mines has become a serious safety problem. This Anaconda research program was conducted to develop a low-cost system for alerting haulage truck operators of the presence of small vehicles in their blind areas. Several systems, developed and tested to help solve this problem, are summarized and evaluated in this paper. As the size of the haulage trucks used in large open-pit mines has increased, so have the blind areas. Mine utility vehicles, pickup tucks and cars become concealed within these blind areas and, thus, become a serious safety hazard. Figure 1 shows the typical blind areas of a 150-ton haulage truck. The areas of greatest concern are those at the rear center and front right corner of the truck. It is within these areas of "no visibility" that numerous small vehicles over the years have been crushed by the large haulage trucks at various mine sites. Although the occupants in most instances, have escaped the vehicle before it was destroyed, injuries and deaths have occurred. The accidents, in most cases, were attributed to negligence or carelessness on the part of the driver of the smaller vehicle, but the problem of limited visibility still exists, and a solution is needed.

Jan 1, 1982

By H. E. Hawkes

Reconnaissance mineral exploration based on the distribution of ore metals in stream sediments has become a generally accepted method of mineral reconnaissance. This approach seems to work almost equally well in all climates and in all kinds of terrain, provided of course that the ore deposits being sought are exposed at or near the surface and are actively undergoing erosion. Nobody with any experience in the field would question the validity of the concept on which stream sediment reconnaissance is based. Considerable dispute does arise, however, when the subject of density of sample sites per unit area, or sample spacing, comes up for discussion. What is the optimum balance between completeness of coverage and cost? The tacit assumption is frequently made that a greater sample density necessarily leads to more complete coverage and hence a lower probability of missing an important discovery, without regard for the size of the stream sample or the topology of the drainage pattern. The purpose of this paper is to attempt to bring the problem of site selection in stream sediment sampling into better focus, and to present a formula that may help in planning reconnaissance programs.

Jan 1, 1976

By R. Fred Pena

The Tower Mill has proven to be a grinding machine with a demonstrated application flexibility. Variations in applications have proven to be numerous. This mill was originally intended for fine grinding applications. Subsequent testwork and installations have demonstrated the mill can be utilized in place of ball mills as secondary mills. The following lists a few of the circuits tested: 1. Tower Mill secondary receiving feed from a primary SAG mill grinding stage. 2. Tower Mill as tertiary grind unit following a rod mill/ball mill. 3. Tower Mill as secondary grind unit following a primary ball mill. 4. Tower Mill as a limeslaker. 5. Tower Mill grinding as a primary unit taking limestone crusher discharge. Applications demonstrate the mill is energy efficient and is sensitive to the following consideration: 1. Circuit chosen. 2. Top size of feed. 3. Product size required. 4. Classification equipment performance. 5. Media size required. 6. Media type required.

Jan 1, 1986

By Terrence J. Stobbe

On the job injuries to the musculoskeletal system are probably the oldest of the industrial safety problems. Long before we had pinchpoints to guard, chemical vapors to ventilate, and noise to enclose, people were getting strains, sprains, and sore backs from their work activities. In spite of the age of the problem, it remains a long way from being solved. The past ten years have seen a significant commitment by the sci¬entific community to understanding the problem. Engineers, scientists, doctors, and epidemi¬ologists have been involved, and as a result, today we have a much better understanding of the problem. The first step in understanding a problem such as this is to explore its history and epidemiology. The research done by Chaffin (1977), Snook (1970), Ayoub (1978), the ILO (1962), and others, led NIOSH to publish its Work Practices Guide for Manual Lifting in 1981. The guide was based on research carried out in general industry, but subsequent research by Stobbe (1983) and Peters (1983) has suggested that the nature of the problems producing injuries in underground mining is the same as in general industry. The problems are more intense in the mining environment.

Jan 1, 1984

By Stephen Utter

This report summarizes the results of preliminary investigations concerning the influence of block caving mining upon adjacent mine openings and discusses possible methods for reducing critical rock pressures and damage to these openings. These investigations are one part of a general study of the rock mechanics of block caving by the Denver Mining Research Center of the Federal Bureau of Mines. The purpose of this part of the study Is to obtain an estimate of the stress concentrations around mine openings adjacent to block caving stopes for use in developing better designed openings and improving mining methods. When mine openings such as slusher drifts, grizzly drifts, and haulage drifts are damaged by rock pressures induced by block caving mining, the mining cost increases, mine production decreases, and ore recovery may be consider- ably lessened. Methods of mining that result in lower rock pressures and methods of design that enable mine openings to withstand these pressures are desirable. The development of these methods, in turn, requires a fuller understanding of the following: The stres concentrations around the mine openings and the changes in stress induced by adjacent mining; the physical properties, such as the compressive strength and modulus of elasticity of the rock surrounding the openings; and the support supplied by the concrete lining, timber sets, or other types of supports used in the openings.

Jan 1, 1962

By William T. Ingram

Early in the 60's the author served as Chairman of the Engineering Foundation's Coordinating Committee on Air Pollution Research. One of our objectives was the development of a study on the measurement of stack emissions. Three publications of the Foundation resulted from these efforts to focus attention on the stack sampling problem.1,2,3 Two of these were annotated bibliographies covering 197 references. The third reported the results of a workshop meeting at which some 21 individuals from research institutes, industry and government discussed the possible and probable areas of research that would add to or increase the ease, precision and utility of sampling gaseous and particulate matter emitted from stacks. The American Society of Mechanical Engineers has had in its Power Test Codes a Standard Code for Determining the Dust Concentration in a Gas stream4 since 1941, The American Industrial Hygiene Association has published, in its Air Pollution Manual,5 a Section on Stack Sampling. Industry and regulatory agency requirements for stack sampling have utilized some modification of the alternatives in methodology. There has been ho single guide to stack sampling that met the needs of those who have the need to know.

Jan 1, 1970

By J. A. Pigott

Undercut-and-fill mining is a method developed by the International Nickel Company to deal with abnormal pillar mining conditions at one of its mines. Results have been such that its use has been extended to normal, pillar recovery operations in other mines of the Company as a replacement for conventional square-set pillar mining. It is anticipated that the method will also largely replace square-set stoping at INCo mines, especially for mining at deep horizons.

Jan 1, 1962

By D. W. McGlashan

Zeta potential changes were determined as a function of pH, metal ion, and surfactant concentrations. Prom the analysis of data, flotation experiments were carried out to correlate float-ability with the differences in zeta potential. Cassiterite in water bears a negative zeta potential, The zeta potential of cassiterite is sensitive to pH changes; the electric double layer arises from the preferential adsorption of H+ and OH- ions and subsequent ionization of the hydroxylated surface. It is suspected that hydronium-ion concentration may cause reversal in the sign of the zeta potential. The ZPC was found to occur at pH 3.4. Metallic ions and the hydrated ions thereof affect the zeta potential of cassiterite in differing degrees of intensity. Without prior activation, sulfonated surfactants do not change the zeta potential of cassiterite. Sodium alkyl aryl sulfonate is especially active on lead-activated cassiterite and ferric-activated cassiteriten Microcalorimetric fiests confimed the activity of ions on cassiterite and showed the hydrated character of cassiterite smfaces. Close correlation between zeta potential and microflotation results was achieved.

Jan 1, 1969

By Joseph P. Nugent

The new combination gypsum plaster and gypsum wallboard plant of Compania Industrial Kaiser S.A., the first of its kind in Mexico went into production in April of 1969. This was approximately fourteen months from the signing of the formal order for the plant and equipment. Compania Industrial Kaiser S.A. is an affiliate of the Kaiser Gypsum Company in the United States and will market practically the same line of products and to the same standards as those produced in American plants. Located in the City of Puebla, the plant will readily service the major Mexican sales areas. It is approximately 85 miles away from Mexico City on a modern, four-lane, divided highway and distribution to other major consumer areas can be readily effected by the use of a good highway system, as well as, by rail. This, plant is the, sixteenth Gypsum Wallboard Mill supplied abroad by my company, United States Wallboard Machinery Company. Other installations are in Australia, New Zealand, Chile, England, Scotland, Ireland, Finland, South Africa, Latvia and Germany. Two new mills are on order; a small unit for Brazil and a comparatively large unit for New Zealand. All these mills have one thing in common with plants in the United States and Canada; they are equipped with standard, time-proven and tested equipment and they are designed in accor¬dance with the latest engineering thinking in order to produce efficiently, the highest quality product at lowest cost. They differ generally in the size of plant, the factors that brought them into being and in the market that they supply. I believe that these differences will be of interest to you.

Jan 1, 1969

By John W. Nebgen

Surface water quality is determined by complicated interactions between water and land. Runoff--the flow of waters in surface streams and rivers-¬represents the total amount of water collected in a drainage basin or watershed that appears at the outlet of the basin. As the water flows through the basin, it is in contact with land and can pick up impurities from the land. Thus, surface waters are not pure--they contain impurities, or "pollutants," in vary¬ing concentrations determined by the nature of the land which they drain. The composition of surface waters thus tends to represent a steady state equilibrium between interactions of water and land. However, when man utilizes the land in the drainage basin or watershed, the natural equilibrium between water in the runoff and the land is disturbed. Such disturbances usually effect adverse changes in surface water quality, as new equilibrium conditions between land and water are established. These adverse changes in surface water quality can be thought of as "nonpoint pollution." Esti¬mation of nonpoint pollutant loads thus ultimately reduces to determining the magnitude of the differences between water qualities before and after man's disturbance of land within a watershed. The important key in making such an estimation lies in the determination of water quality in the natural or "back¬ground" condition of the watershed. In subsequent discussion in this paper, tools for making an estimation of background water quality will be described.

Jan 1, 1975

By D. J. Rose

The San Miguel Mine is owned by San Miguel Electrical Cooperative, Inc. and operated by Atascosa Mining Company, a wholly-owned subsidiary of Morrison-Knudsen Company, Inc. This multiseam, single-zone lignite surface mine is located near Jourdanton, Texas, 110 kilometers (68 miles) south of San Antonio. Lignite extracted from four closely-spaced seams is used to fuel the 400-MW San Miguel Power Plant. Recovery depths range from 7 to 37 meters (25 to 120 feet). The mine began stripping operations in the spring of 1980 and now produces approximately 2.5 million tonnes (2.8 million tons) of lignite annually. Atascosa Mining Company is responsible for production, maintenance, engineering, and management services. Production responsibilities include topsoil removal, overburden removal, lignite mining, spoil pile regrading and topsoil replacement, as well as ash disposal and construction and maintenance of water retention and diversion facilities.

Jan 1, 1984

By Z. R. Llanos

The petroleum refining industry makes extensive use of catalysts for the conversion of crude oils into more usable products such as gasoline, fuel oil and gas, aromatics, and others. Catalysts used for hydraprocessing contain cobalt-molybdenum or nickel -molybdenum, although there are catalysts that also contain tungsten. During hydroprocessing, nickel and vanadium are deposited on the catalysts, eventually rendering them inactive. The refiners are then confronted with the problem of disposing the spent catalysts. In the past, landfilling was a common method of disposal and it is still practiced in some countries. Other refiners prefer to stockpile the spent catalysts at the refineries until the price of metals warrants their sale to metal reclaimers. This practice, however, poses environmental problems to the refineries for storage and disposal of spent catalysts. Other types of catalysts are amenable to regeneration. The purpose of this paper is to focus attention on the recovery of nickel, cobalt, molybdenum, vanadium, and alumina from spent hydroprocessing catalysts by Gulf Chemical and Metallurgical Corporation and to review the use of sodium hydroxide and sodium carbonate for pressure leaching of spent catalysts.

Jan 1, 1986

By Zhiyuan Shen, Dan Zhao

The abstract discusses the importance of reliable mine monitoring systems for preventing accidents. It focuses on diagnosing ventilation system failures caused by roadway faults that alter airflow resistance. The paper proposes using an improved Support Vector Machine (SVM) method to identify the fault location based on changes in air volume detected by wind speed sensors. The approach involves building a sensitivity 0-1 matrix and establishing a roadway fault scope library. The improved SVM method is tested on the Daming coal mine, demonstrating its effectiveness in diagnosing fault locations, reducing training time, and improving accuracy compared to traditional SVM.

Apr 5, 2022

By Don Cchultz

The United States Forest Service, as a land managing agency, is responsible for the surface administration of National Forest lands. The basic objectives of management are protection and utilization of renewable resources such as water, forage, timber, wildlife, recreation, and clean air. Much of the National Forest land in this country is open to mineral prospecting and development. When large de-posits of minerals are extracted from the forest environment, especially by surface methods, there are oftentimes conflicts between accepted mining methods and the objectives of other resource management goals. Such is the situation in Southeast Idaho where several members of the phosphate industry are operating on and adjacent to the Caribou National Forest. In 1966, the phosphate industry and the Caribou National Forest became mutually concerned with the problems of rehabilitating mined areas and minimizing potential damage to adjacent forest areas. A Cooperative Administrative Study was initiated with industry supporting the Forest Service financially and with equipment, material, and manpower, as well as interest and enthusiasm. The objectives of the study are to provide basic, applicable information pertinent to: 1. Protecting the quality of water emanating from mined water-sheds. 2. Providing for soil stabilization on mined areas. 3. Returning mined areas to surface resource production. 4. The feasibility of making mined areas esthetically acceptable. It was concluded that the following separate--yet intergrated--fields should be studied in order to obtain the desired information:

Jan 1, 1971

By R. G. Church

Belle Ayr Mine was established in 1972 as the first large surface coal mine in the Powder River Basin of Wyoming. During the mid-1980s, it was eventually out-distanced in productivity by newer mines, and management recognized that the mine must recapitalize its major mining equipment and enhance its workforce flexibility in order to be competitive in the deteriorating market situation. Therefore, state-of-the-art haulage and loading equipment was placed into service, and a 12-hour rotating shift and a technician-based workforce was implemented. Belle Ayr Mine is located 29 km (18 miles) southeast of Gillette, Wyoming, in Campbell County (Figure 1). The mine is a part of AMAX Coal West, Inc., and with its sister mine, Eagle Butte, located 8 km (5 miles) north of Gillette, is a major contributor to the overall coal production of AMAX Coal Industries, Inc., headquartered in Houston, Texas. This paper addresses mine planning, recapitalization initiatives, and innovative workforce changes which propelled this large, surface coal mine to the forefront of productivity in the ever tightening low sulphur coal market.

Jan 1, 1994

By Robert Cook, Valeria Zarate, Jason Hallowell

The long hole open stoping (LHOS) method is widely used in underground mining. While methods to predict stable stope geometries are well established, the ability to maintain a stable back often assumes effective ground support across the full stope span. The efficacy of the support strategy is dependent on rock jointing, quality, density, top cut width and height, and the type, amount, and orientations of bolts installed. However, it is becoming increasingly common for operators to assume narrow top cuts in service of wider stope spans with minimal bolting coverage. Failure to account for the required top cut drift size and support requirements can ultimately lead to raveling type instabilities along stope shoulders that result in back collapse. A new method has been developed to evaluate the minimum top cut dimension necessary to accommodate wider stope spans with various rock bolting configurations. Due to the economic impacts of top cut development and support, this is a critical consideration in the accurate costing and scheduling of a LHOS operation. Tables 1 lists the acronyms are used throughout this paper.

Feb 1, 2025

By Ulf Georg Gwildis

Overexcavation and ground loss events during pressurized-face TBMadvance in soft ground can result in unplanned deformations above the tunnel and damage to existing infrastructure. Successfully managing the risk of this occurring is crucial for any project in an urban area to proceed. Common risk management approaches include a combination of establishing suitable ranges of TBM operational parameters and using geotechnical instrumentation for deformation monitoring. Another risk management tool is material flow reconciliation, which varies depending on the specified mining method and the equipment choices by the contractor. This paper compares recent and ongoing projects in the Pacific Northwest regarding overexcavation risk management.

Jun 13, 2023

By Isabel Barton

This article describes and analyzes the history of research into the origins of the uranium-vanadium(-radium) deposits of the Paradox Basin. For several decades after their discovery in 1881, research was desultory and almost entirely descriptive, fluctuating with demand for vanadium and radium. Systematic geologic descriptions, accumulated between 1910 and 1950, supported rapid progress during a government-backed surge of research in the 1950s, when uranium was the chief commodity of interest. Most of the major theoretical innovations date from this decade, including the use of concepts from solution chemistry to identify the conditions and constrain the processes of deposit formation and alteration. Research from this time was highly influential in geology at large, providing the model for sandstone-hosted uranium deposits worldwide and numerous new minerals and mineral structures. After about 1960, mine production remained high but research dwindled, and most new advances were to the details of the hydrothermal model of ore formation rather than its core concepts. By the end of the 1960s, the deposits were understood to have formed at the mixing interface of an oxidized, metal-bearing water with a reducing fluid of debated origin. Research was desultory over the ensuing decades; the source of the metals and the nature of the chemicals constituting the trap were not clearly established. They remain questions today, as do factors like the relationship between ore mineralization and the geologic history of the basin. (More in the full paper.)

Jan 1, 2025

By W. Hu

Gravity concentration has been the main method for tin ore beneficiation, based on the significant difference of density between cassiterite and gangue in the tin ore. However, with the exhaustion of rich and coarse reserves, the proportion of tin distribution in slime be-comes as high as 50 to 70% and has a size range of -19 urn. In some sulfide tin ore, most of the tin is of the minus 10-urn size fraction, and thus slime processing has gained importance in tin ore processing. Some innovations are being developed, such as the centrifugal cone separator, belt concentrator, slime table, B-M separator, and slime flotation. Direct flotation with tolyl arsonic acid has been practiced with success.

Jan 1, 1989

By Brett P. Spigarelli

"To meet the growing need for CO2 capture and storage technology, Michigan Technological University is studying CO2 capture using alkali-based solvents. The objective of the present study was to find a way to increase the absorption rate of CO2 into an alkali solution without reducing the absorption capacity of the solution. One approach to increasing absorption rate is to use a surfactant to chemically alter the gas bubble size. The surfactant chosen for the study was a neutral-charge polypropylene glycol methyl ether (PPGME) with a molecular weight of 200. Experiments were conducted to study the absorption rate of CO2 at varying surfactant concentrations. Results showed that as the concentration of PPGME increased in solution, the absorption rate also increased. The CO2 absorption rate increased from 3.45 x 10-3 mol/min CO2 at 0g/L PPGME to 3.92 x 10-3 mol/min CO2 at 0.48 g/L PPGME. This amounted to a 14% increase in the CO2 absorption rate with no decrease in the absorption capacity of the solution. IntroductionChemical absorption using an amine solvent is currently the most mature carbon capture and storage technology available. Amines are advantageous in that they have a fast CO2 absorption rate, which leads to a high CO2 removal efficiency. However, amine absorption has some considerable drawbacks, such as high energy requirements, high equipment corrosion rates, amine degradation in the presence of oxygen, high waste generation and a large increase in plant footprint if new equipment is constructed (Herzog and Golomb, 2004; D’Alessandro et al., 2010). Due to these drawbacks, Michigan Technological University (MTU) is studying CO2 absorption using alkali-based solvents, which address the above disadvantages of amine solvents."

Jan 1, 2015